Search Documents

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By J M. Menacho, L Zhang, A Hoadley, L Verdugo, B Etschmann, W Bruckard

Since the introduction of Lithium-Ion Batteries (LIBs) in 1991, the market for lithium-ion cells has been driven by the high demand for portable electronic devices and more recently for batteries for the electric car industry. It is expected to grow rapidly to reach 2600 GWh globally by 2030 (US Government, Office of Energy Efficiency and Renewable Energy, 2021). However, there is a desperate need to recycle LIBs to recover valuable cathode materials and graphite. For this reason, several physical and chemical recycling technologies have been proposed to recover these materials from spent batteries. Amongst these, froth flotation technology is a potential cost-effective technology for separation of the graphite fraction from the lithium oxide components due to the natural hydrophobicity of graphite and density difference between graphite and cathode materials (Folayan et al, 2021).

Aug 24, 2022

By M Manefield, G Bournival, S Ata

Asteroids contain an abundance of valuable resources such as: nickel, cobalt, gold, platinum and rhodium. Whilst the consumption of mineral resources on Earth continues to deplete, meteoroids have the potential to become a significant source of minerals. Even though the minerals content of asteroids may be relatively high, the valuable minerals are more likely to be only a small portion of the total ore present in the main body. The ores must, therefore, be processed to extract the metals of interest from the waste. Existing terrestrial technologies rely on manipulating the physical and chemical properties of minerals. The application of these techniques to asteroids processing, however, is not straightforward due to the presence of different conditions such as zero gravity and lack of water in space. This paper discusses potential separation and extraction techniques that can be used for processing of asteroids.CITATION:Ata, S, Bournival, G and Manefield, M, 2015. Resource recovery in space, in Proceedings Third International Future Mining Conference, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By T Berryman

The Fimiston reserve is being depleted at the rate of one million ounces per year; most of which is processed by the Fimiston plant, with the remainder being stockpiled. As for most other large open cut mines around the world, Fimiston has an excellent dispatch and tracking system. Reconciliation is used to determine how the various models used in mine planning (such as a reserve, budget and schedule models) are tracking against production. It is also used to gauge the performance of grade control estimation against production; however, analysing the results of this can be complicated and, at times, misleading. The reconciliation process involves adjusting the monthly production data to equal the mill reported tonnes and grade, plus the change in stockpiles. This adjusted number is then compared to the grade control reported tonnes and grade, the scheduled model (monthly planning model) tonnes and grade and against budget (Reserve) tonnes and grade. This paper includes explanations of all assumptions made in the reconciliation process, including the end of month closing stocks balance, the application of adjustment factors to the dispatch data to create a new balanced set of production data and the monthly sign off to comply with the Sarbanes-Oxley requirements of the North American owners. The reserve is reconciled by proved and probable classification. This tool is used to assess the robustness of the classification scheme utilised and identify any reconciliation issues as they arise. Within the Fimiston deposit there are still issues that are clouded by the assumptions made concerning the scale of observation, poor data support and the mining of the narrow lode areas of the deposit. The declared ore mined (DOM) number (which is defined in the paper) can be significantly affected by these assumptions, and these need to be clearly stated and understood when looking at the reconciliation data. The DOM tonnes and grade is a good indicator of real mine performance as it adjusts mined tonnes and grade to take into account the milled tonnes and grade each month, and prevents cumulative errors from building up in mine predicted dispatch numbers or end of period stockpiles. This number allows monthly monitoring of the mine to mill performance and allows valid comparisons to be made back to budgets and reserves over a period of time. KCGM uses three month rolling averages to monitor performance against reserve and budget models. This ensures that monthly distortions in the figures due to stockpiling issues or over mining in a particular period do not lead to false conclusions. Reconciliation performance over a longer period (12 - 18 months) is used to adjust reserve models should significant variance be observed. By closely monitoring the reconciliation performance at the Fimiston operation, fine tuning of all aspects of the grade estimation process from reserve through to grade control can be made. This allows the most accurate data to be used when planning from reserve data for the Life of Mine Plan through to grade control data for short-term mill feed.

Jan 1, 2006

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Andrews JRG

Chrysotile asbestos is a valuable resource. Used as a reinforcement in asbestos cement, products are obtained which are cheap, are not attacked by vermin, do not rot or support growth of fungi and are unaffected by water or humid conditions. Such products are of great value in the developing countries where inexpensive and durable building materials and pressure pipe are very important to development, housing and water supplies. Concern over the adverse effects of inhaling asbestos has led to the introduction of increasingly stringent controls world wide on the quantities of airborne asbestos per- missible in the occupational situation. Wet processing has the potential for virtually eliminating the environmental concerns with asbestos dust both in fibre production and in the materials handling section of the manufac- ture of asbestos cement products. In addition, high efficiencies associated with wet process- ing mean that better yields are obtained and that the tailings which are dumped have a lower residual asbestos content. Since early 1977, ICI Australia and Woodsreef Mines have been engaged in a programme of research to develop and evaluate a wet mill- ingprocess to produce, from ore and existing tailings, high grade fibre suitable for use in asbestos cement products. The process has been developed through microscopic studies, labora- tory bench scale experiments, work in a small scale semi-continuous plant and product evalua- tion on experimental size Hatschek asbestos cement machines. A prototype mill with a normal feed rate of 1z tonnes per hour and capable of producing pipe grade asbestos from Woodsreef ore has been constructed and was operational from January, 1982 to July, 1983. A range of asbestos cement products have been made successfully on full scale Hatschek machines using fibre from ore and tailings milled in the prototype mill. Economic evaluations indicate that a wet process mill would be cheaper to build, operate and maintain than an equivalent dry process plant. A commercial plant has been designed 1. Manager New Process Development, Woodsreef Mines Limited, Barraba, Australia. 2. Senior Lecturer, Department of Chemical Engineering, Monash University, Vic, Australia. formerly Senior Research Officer, Research Department, ICI Australia Limited

Jan 1, 1986

By A Karrech, A Hasan

This paper presents the numerical simulation of mine backfilling in underground stopes using three-dimensional discrete element modelling (DEM). The simulation predicts the forces exerted at the stope base and barricade with respect to time under free drained conditions. The results of the numerical simulation are validated using basic analytical solutions and advanced experimental tests involving a geotechnical centrifuge system. Overall, a good agreement between the present numerical simulations and the existing experimental and analytical results was found. The present model suggests that DEM is a promising computational tool to predict barricade pressure in underground mine stopes.CITATION:Hasan, A and Karrech, A, 2014. Simulating mine backfill in a fully drained condition using discrete element modelling, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 117–124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P F. Knights

Mining companies are striving to achieve new levels of operational maturity and drive process improvement across the organisation in the face of unprecedented demand and limited supply of experienced human resources. Advanced analytics techniques can help overcome these fundamental challenges by applying data techniques not previously applied in mining. Today, decisions are usually locally optimised but do not achieve optimum capability for the value chain. Although more information is collected then ever before, it is difficult to link many sources of data together in the same place in real-time, for example plant history, maintenance, mine planning, logistics and engineering data. Consequently complex analysis of data is time consuming and requires specialist skills and knowledge, and is often neglected in the decision-making process. In the future, analytics will close the loop between analysing data and taking action. Analytics will become embedded in the business and routinely applied to improve decision making across the organisation, from senior management to operations and maintenance workers, but will not require specialist skills or be time consuming to analyse data. As analytics becomes embedded in the business process, decisions are supported by data (not on gut feel), and critically, data from many sources are integrated in real-time to improve the quality of decisions. Ultimately, predictive tools will help suggest, or even in some cases automate, courses of action. The main opportunities for analytics exist where the enterprise requires supporting technology to enable it to continue to evolve to higher level of maturity. This will be in the areas of asset management, rapid reconciliation and adaptive planning, and the inbound and outbound supply chains. Advanced analytics are also a key enabler for increasing the effectiveness and realising the true value of Remote Operations Centres to safely and efficiently support operations in remote locations with smaller workforces.

Jan 1, 2008

By D Craw

Otago Schist and Klondike Schist are two Paleozoic-Mesozoic metamorphic belts on the circum-Pacific margin in which there has been a long history of abundant alluvial gold mining, but only minor hard-rock gold mining.   Modern exploration for hard-rock gold is ongoing in both belts, and the active Macraes mine in Otago (>2 Moz production) highlights the hard-rock potential of the geological setting of these belts. Hard-rock gold mineralisation in both belts formed in the latter stages of schist exhumation, after rocks were subjected to major regional ductile folding and then uplifted through the brittle-ductile transition. The majority of known hard-rock gold-bearing systems in both belts consist of well-defined, but generally discontinuous, vein swarms. Most Otago veins are hosted in steeply dipping post-metamorphic normal faults and fractures. However, the Macraes mine is hosted by a late-metamorphic shear zone, and much ore is sulphide-impregnated auriferous schist. Goldbearing veins in the Klondike schist are hosted primarily in extensional sites associated with post-metamorphic compressional structures. Some disseminated sulphide mineralisation is associated with Klondike veins and this is important as it extends the exploration target for these veins. No foliation-parallel late metamorphic mineralisation has been identified in the Klondike but exposure is relatively poor compared with Otago and both schist belts are highly prospective for deposits of this type.

Jan 1, 2007

Gallium occurs at above background levels in most samples collected from 11 of the major geothermal areas in the Taupo Volcanic Zone. Concentrations of Ga in the 48 samples ranged from 8 to 144 mg kg-1 and varies widely from place to place within each geothermal area. Gallium is contained within the alumino-silicate structure of clay in the mud, having substituted mainly for Al. Suggested deposition mechanisms for Ga also involve co-precipitation with Sb, As, and SiO2 colloids. Digestion trials, carried out to determine extraction conditions for possible commercial exploitation, showed that heating the mud to 500 - 600¦C for 1 hour followed by acid/alkali treatment gave complete recoveries.

Jan 1, 1995

By I R. F MacCulloch, K Jones

Pintail Systems, Inc, a Colorado USA based company has developed and commercially applied bioremediation processes for biological detoxification of cyanide compounds in mine waste. Site-specific microorganisms are isolated from spent ore, tailings or process solutions and augmented in the laboratory for cyanide oxidation, denitrification and metal biomineralisation. Biological processes typically treat complex contaminants (cyanide compounds, soluble metals and nitrates) in a fraction of the time of conventional remediation processes. Cyanide is used in microbial metabolic processes as a carbon or a nitrogen source. Biological detoxification processes applied at the end of mine life can end long-term liability and perpetual monitoring and containment. Case studies from commercial application and demonstration programs for the US Environmental Protection Agency will be presented in this paper.

Jan 1, 2004

By Gao K, Wu C, Langley J. M, Waugh B, Farrell K

The dissolution of carbon from carbonaceous materials into molten iron is a key step in various ironmaking operations. For example, in new direct smelting processes, carbon in the form of coal is injected into the molten iron bath, which leads to the dissolution of carbon. In foundry operations, typical recarburizer materials can range from high purity graphite to chars. The dissolution performance of these" materials is critical to the operation and could dictate the efficiency and economics of the process.Dissolution kinetics has been studied by various investigators to explain the influence of melt conditions and carbon type (Sahajwalla et al, 1994; Shigeno, Tokuda, and Ohtani, 1985; Orsten and Oeters; 1988; Ganguly and Reid, 1992; Wright and Taylor, 1993). The influence of melt sulphur content on the dissolution kinetics has been characterised (Sahajwalla et al, 1994), with sulphur retarding the rate of carbon dissolution. The carbon dissolution from different sources is seen to vary significantly even under similar melt conditions. This observation has been explained by investigators on the basis of the varying ash content present in the carbonaceous materials. However, ash content alone cannot account for the variability in dissolution kinetics reported in other studies. One such study is presented below.In a recent study (Sahajwalla et al, 1994), pulverised carbonaceous materials were injected into the molten iron bath and the" dissolution kinetics was established. The dissolution of graphite and glassy carbon, which contain almost 100 per cent carbon, was seen to be significantly different when the molten iron contained sulphur. The influence of melt sulphur content was explained on the basis of different wetting behaviour observed.Importantly, the study showed that even pure carbon sources dissolved at significantly different rates. Hence, their performance could not be explained on the basis of ash content.The key difference between graphite and glassy carbon is in their atomic structure. Graphite is highly ordered whereas glassy carbon has relatively poor ordering in its atomic structure. This study showed that the atomic structure in carbonaceous materials can have a significant effect on their dissolution performance.The focus of the present investigation which stems from the past study described above (Sahajwalla et al, 1994), is to investigate the influence of atomic structure of carbonaceous materials on their dissolution into Fe-C-S melts.The specific objective of this study is to determine the relationship between dissolution kinetics and crystallographic character of carbon sources. In order to accomplish this goal, a range of different materials representing a spectrum of carbon sources have been chosen for the investigation. These materials include brown coal char, two types of Auscarb (A and B), and commercial graphite. Auscarb is prepared by calcining Auscoal at 1000°C. Auscoal is made from chemically cleaned Australian coals (Bowling, Chandler and Waugh, 1990). Part 1 of this paper details the dissolution performance of the materials studied, while Part 11 describes the X-ray diffraction study. The relationship between the atomic structural dimension and dissolution rate constant is discussed in light of the results obtained.

Jan 1, 1996

By Y L. Ma, M Chen, W Bruckard

With the extensive exploitation and gradual depletion of high-grade copper reserves, the mining industry is paying more and more attention to the hydrometallurgical extraction of copper from lowgrade and arsenic bearing copper ores. Hydrometallurgical processing, such as heap leaching, column leaching and bioleaching, provide a viable alternative to the traditional pyrometallurgy due to its harmony with the environment, moderate capital investment, and low operating costs. However, the slow leaching kinetics of enargite (Cu3AsS4) and chalcopyrite (CuFeS2) remain problematic for commercial leaching practice. The formation mechanism and the nature of the passivating layers during leaching is still a matter of debate in hydrometallurgical research. In this study, the dissolution mechanism of enargite and chalcopyrite in sulfuric acid solution was investigated using a range of electrochemical and spectroscopic analysis methods. Electrochemical oxidation of enargite demonstrated an obvious passivation region from 500 to 750 mV (Ag/AgCl). The formed passivation film was found a n-type semiconductor behaviour, which is different from the original enargite with a p-type behaviour. The results of X-ray photoelectron spectroscopy (XPS) suggested that a nonstoichiometric film Cu(3−x)As(1−y)S4 (x>>y) accumulated on the electrode surface, which accounted for the obvious decrease in current density in the passive potential region. For chalcopyrite, three important potentials of 550, 680 and 730 mV which are related to the formation and dissolution of passivation film were observed based on the cyclic voltammetry (CV) and potentiodynamic polarisation. Raman and X-ray absorption near edge structure (XANES) spectra studies of the chalcopyrite electrodes after being treated under these three potentials indicated a metal-deficient sulfide of Cu1−xFe1−yS2 (y>>x) might be responsible for the passivation phenomenon. Hence, it is concluded that the passivation of enargite and chalcopyrite are similar which are caused by metaldeficient sulfide surfaces although the compositions of the metal-deficient sulfide are different.

Aug 24, 2022

By Paton T. P

In the technical sense, as well as in the professional sense, the word 'model' can have many meanings. More than 23 000 references were uncovered by a simple literature search on keywords ' MO D EL#. and. (META LLURG#. or. M I NERAL#)' . For the purpose of this paper, 'models' will be considered to be mathematical formulations which attempt to represent or approximate a process. The model may be purely, or a combination of: ò fundamental models, based on the laws of physics, chemistry and thermodynamics; ò semi-empirical or phenomenological models, where an intuitive concept of the process is formulated and found by testwork to fit observed behaviour; and ò empirical or 'black-box' models (including neural networks), where a mathematically convenient form is proposed and fitted. Even under this more restricted definition, which eliminates heuristic and statistical 'models', it is clear that the efforts expended in devising and using models have exploded during the years since the first APCOM Conference in 1961, benefiting from the dramatic decrease in the cost of computer power. This paper reviews the areas of usage of computer modelling in the metallurgical and mineral processing industries, from plant design, through off-line support, to on-line modelling and automatic control. In each area, frontiers of new development of the technology are mentioned. It is noted that, while modelling is now standard practice in design, it is not yet the norm in operating and controlling plants. The reasons for this partial acceptance are, it is argued, less related to the limitations of the technology than to the human and organisational factors involved in transferring technology to implementation.

Jan 1, 1995

By R C, K L. Rees, J S. J van Deventer

In contrast with previously published models for the carbon-in-pulp (CIP) process, the model proposed in this paper incorporates film transfer, intraparticle diffusion, simultaneous leaching, preg-robbing, the loading of multicomponent species, and the effects of fouling and changing cyanide levels. The rationale behind this comprehensive model is that changes in fouling and competitive adsorption along a CIP cascade affect the profiles of gold loading. As it is impossible to quantify all these non-ideal factors, a method is proposed whereby an imaginary species is postulated so as to combine all the competitive effects. A plant survey at the Telfer mine has shown that the mass loss due to a gravimetric analysis of the fouled carbon could be used directly to quantify this competitive effect. The degradation and consumption of cyanide along the Telfer CIP cascade enhance the loading of copper on to the carbon, which should be taken into account when modelling the gold profiles. It appeared that the effect of cyanide itself on the loading of gold was negligible compared with its effect on the copper. Evidently much more research is required on this topic in order to optimise CIP operations exposed to constantly changing conditions.

Jan 1, 1998

By J Wu

Swirl Flow Technology (SFT), a novel approach for agitation in large industrial slurry tanks, was jointly developed and patented by CSIRO and Queensland Alumina Ltd (QAL). Currently, SFT is used in 16 alumina precipitation tanks at QAL, with the first installation in January 1997. This paper provides insight to the underlying fluid dynamics, which were investigated through pilot-scale experiments. A key finding was that SFT produces tank wall velocities approximately four times that of conventional draft tube agitator systems for the same power input, whilst for solids suspension, much less power is needed. SFT is energy efficient and practical in scaling suppression as demonstrated by the full-scale experience at QAL.

Aug 8, 2011

Stringent environmental benchmarks imposed by governments and successful legal challenges in the country of origin have changed the risk profile for all mining companies over recent years. In developing countries, however, where high government standards may not always be in place, direct community action has often made worthless substantial investments in otherwise viable mining operations. Real limitations are therefore imposed from these risks on all areas of mining activity, wherever they may be. Thus, the bar has been raised for all companies developing or operating mines. This paper argues real financial and global industry reputation benefits accrue when all known environmental risks, where practical, are managed. In response, among major international mining companies, as the industry moves towards greater global consolidation, senior management teams have increasingly adopted corporate governance standards including æTriple Bottom LineÆ (shareholder/government/community) sustainability reporting. Sustainability reporting is encouraged by improved international stockholder and financial investor perceptions by contributing to lowered social, community and geopolitical risk which lowers the cost of access to funds as well as improving staff morale and productivity. New mines must not only be primarily financially viable but must operate throughout in a sustainable way. Case studies of some recent mining operations, who have not foreseen or proactively managed major environmental risks, demonstrate the dire financial and personal implications for managers, directors and shareholders from not identifying and managing these environmental risks. Merely having a corporate policy statement on environmental standards or high level Government approvals process for a mining activity does not preclude mining operations from the risk of direct action by local populations or future adverse legal implications from risks which were perhaps identified but not mitigated effectively. Methods and processes for the identification and active management of environmental risks in the global arena are discussed to add a practical element to sustainability, based on the authors recent strategy development processes with governments and major mining houses such as BHPBillition, Rio and Xstrata. Emphasis is placed on proactive, innovative yet practical solutions which, where possible, show positive contributions firstly to the financial bottom line but also the community at large.

Jan 1, 2003

By D J. Williams, M S. Zbik, A Shokouhi

There is a considerable difference in the particle size distribution (PSD) of clay mineral-rich coarse coal reject with variations in the test moisture state and the chemistry of the water used for testing. The coarse coal reject tested were collected from Jeebropilly Mine, located in the Ipswich Coalfields of south-eastern Queensland. Differences between the results of dry and wet sieving analysis indicate a significant breakdown of the clay mineral-rich coarse coal reject on wetting-up. Wet sieving caused a breakdown of the gravel-sized fraction to silt and clay size without significant breakdown to sand size. There is also a considerable variation in the results of hydrometer analyses of the clay mineral-rich coarse coal reject with variations in the chemistry of the water used, particularly at the fine end of the particle size range. The waters used included tap water, coal processing water and deionised water. In addition, the method of dispersion applied prior to hydrometer analysis can have a significant effect on the PSD of clay mineral-rich coarse coal reject, with boiling and sonic vibration causing the most breakdown of the clay particles. This paper describes the testing methodology used and the test results obtained, and attempts to explain the results in terms of clay mineralogy and water chemistry.CITATION:Shokouhi, A, Williams, D J and Zbik, M S, 2015. Influence of water on particle size distribution of clay mineral-rich coarse coal reject, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

A low grade, refractory ore gold mine with high striping ratio such as at Macraes is always challenged in ways to improve margins. Common practice approaches used at OceanaGold Ltd Macraes are to maximise grade delivery, optimise recovery and reduce unit costs, as well as take any opportunities to incorporate new technologies and implement enhanced commercial strategies.   The Business Improvement (BI) programme was implemented across the Macraes operations in late 2003 and is being rolled-out to all other parts of the business. The core focus of BI at OGL is to: +        increase revenue, +        reduce cost, and +        improve processes.   A dedicated BI team comprising of a manager, team leaders and business analysts were engaged to identify and manage a series of opportunities to reduce operating expenses, optimise capital outlays and generate extra revenue. The Business Improvement Programme, though in its formative phase, has begun a cultural change within the organisation. Many people are starting to challenge the way they do things and are looking for ways to continually improve business performance.   The BI team encompasses individuals from different departments who can offer the diverse skill set necessary to produce intended results. The current team is made up of a BI manager, BI Team Leaders in Mining and Processing and analysts from Mining, Processing, Commercial and Plant Maintenance workgroups. A team member has recently been formally trained as a Six Sigma Black Belt. ] The BIÆs team role is to assist in the establishment of project management processes for each improvement idea. In addition the team will assist in tracking implementation, identifying and unblocking restrictions and limitations as well as setting up metrics to quantify the level of benefit returned and sustained.   From a more strategic point of view, the BI team is advancing the Business Improvement capability of the company by developing long term Communication and Training strategies. These strategies will set the direction of BI initiatives in the years to come to: +        educate the OGL workforce in basic BI techniques, +        assist the OGL workforce in applying basic BI techniques, +        communication the direction of BI in OGL, and +        close the information feedback loop to facilitate transparent communication between the OGL workforce and the BI team.

Jan 1, 2004