Search Documents

By M Heidari, M Ataei

Today, the selection of a mining method is a multi-criteria decisionmaking process, with many factors in this process connected to each other. These trends do not have a high degree of confidence. In this study the analytical hierarchy process was used to select the suitable mining method for anomaly No 3 of Gol-Gohar iron mine of Iran. The results of this study show that gathering all existing information from the exploration stages and using AHP technique, the open pit mining method is the mining method for this anomaly.

Jan 1, 2003

Leadership challenges for mine management over the next decade will be primarily about doing more with less labour. This will require a greater focus on people leadership and management, reducing uncertainty by evening out employment peaks and troughs, understanding and addressing our demographic destiny and its implications whilst identifying and holding onto our mission critical employees, managing creativity and accepting diversity whilst providing flexibility in employment for work-life balance. Greater emphasis will also be required on the non-technical social skills of complex interactions with community and education providers and finally a greater emphasis on forecasting and planning for the provision of future skills needs. Skills needs will become an ever increasing priority in risk management as retention starts with attraction and remember: SATISFACTION = REALITY                                EXPECTATIONS These are the challenges and opportunities for leadership and mine management of the 21st century to assist in better meeting and maintaining our human resources needs and thus contributing to the sustainability of the sector in Australasia.

Jan 1, 2006

Epicentres of recent shallow earthquakes in the region (3-12¦S, 126-150`E) were plotted to identify the various plate boundaries in the region, in particular the southernmost one marking the northern edge of the Australian plate. New and published fault plane solutions were examined to determine the style of faulting and state of stress along the Australian plate boundary. From east to west the boundary is first a subduction zone along the Solomon Islands, then a spreading centre across the Solomon Sea, a zone of compression and left lateral strike slip along the Papua Peninsula, almost pure thrusting across the centre of New Guinea and lastly left lateral strike silo through Irian Taya to the outer Banda Arc. The principal stress is very consistent, trending NW to NNW in a near horizontal plane, from the triple junction of the Pacific, Solomon Sea and Australian plates in the east to the Banda Sea in the west. Only along southern Solomon Sea plate margin which is a divergent boundary, is the stress different in type and direction.

Jan 1, 1987

Studies of the minor element content of sphalerite and pyrite have generally been concerned with individual deposits or localised groups of deposits. However, a small number of more regional investigations have been reported (e.g. Davidson, 1962; Groves and Loftus-Hills, 1968; Loftus-Hills and Solomon, 1967; Price, 1972; Bralia et al., 1979) which have used the minor element abundances to evaluate the petrogenesis and geological affinities of diverse ore types and to fingerprint metallogenic provinces (e.g. Ivanov, 1964). While generally held to be valid, some doubts have nevertheless been cast on the reliability of minor element abundances in petrogenetic deliberations (e.g. Mercer, This paper reports on the distribution of he. Cpl and Mn in sphalerite, and Co, Ni and Mn in pyrite, from sulphide mineral occurrences within the "eugeosynclinal" prism comprising the New England Region of north-eastern New South Wales and south- eastern Queensland (Fig. 1). The occurrences examined are representative of two well-defined styles of mineralisation (Stanton et al., 1974) within which clear patterns of ore-rock distribution give rise to specific metal associations (Herbert. 1977).

Jan 1, 1987

Sample preparation for gold samples, where the distribution and size of gold particles is often irregular, usually demands that a relatively large sample weight is taken to produce a representative sample for analysis. Traditional sample preparation of gold samples incorporated multiple stages of coarse particle size reduction followed by subdivision of the sample prior to final fine pulverising. This technique developed because of the limited equipment options available to laboratories. As a result significant errors are introduced and the final sample size being pulverised is a small fraction of the original sample weight. Three significant developments have occurred in the last 25 years to significantly improve sample preparation of gold samples: 1.  large capacity fine pulverising,2.  fine jaw crushing, and3.  whole sample coarse pulverising. In the mid-1980s an Australian manufacturer developed large capacity pulverising bowls which had the ability to reduce samples with a mass of 1.5 - 3.5 kg to a nominal 0.075 mm product in approximately three to five minutes. Laboratories were able to produce a large homogeneous pulverised sample which significantly reduced the error in sampling. However, exploration and mine samples are usually 7 to 10 kg and the sample requires a subdivision stage following crushing to produce the 3.5 kg for the pulverising step, thus introducing potential for significant error. The development of fine jaw crushing allowed particle size reduction to -2 mm which reduced the subdivision error of the bulk sample prior to fine pulverising. Subdivision of the crushed sample at -2 mm still results in potential sampling errors, where the gold particles are not sufficiently liberated to be representatively sampled. Clearly the best option would be to reduce the particle size small enough to ensure a representative sample prior to final pulverising. Continuous mills offer a partial solution but are relatively slow and subject the sample to differential pulverising prior to subdivision. Clearly this does not provide the best solution for routine laboratory applications where high volumes of samples are to be processed. The recent development of a large capacity coarse pulverising system allows samples of up to 10 kg to be reduced to -0.25 mm prior to subdivision, and fine pulverised to -0.075 mm. Laboratories now have the necessary equipment to perform reliable large capacity sample preparation of gold samples. The exact choice of a sample preparation scheme may still depend on particular ore types but the need for multiple crushing and subdivision stages is redundant.

Jan 1, 2008

There are two main challenges in analysis of spectral data: to output as accurate an interpretation of the sample mineral assemblage as possible and to then use the spectral data to map out trends (downhole, across section or traverse) that will assist the exploration geologist to target drilling and further exploration. This paper will discuss methods of extracting the maximum amount of information from spectral data and examples of plotting the information downhole, in section and plan view to assist in exploration and mining. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Onton W

During the latter part of 1936, conditions encountered in sinking the Main Ore shaft made it impractical and uneconomical to continue deepening it to serve haulage levels below the present No. 5 level. Plans were therefore made for an interior shaft, to serve new lower levels, that terminated above No. 5 level so that ore hoisted could be drawn off on this level and transported to the Main Ore shaft for final conveyance to the mill crude ore bin. The No. 2 interior ore shaft was only developed below No. 4 level and borehole ropeways with a winder located on the surface were installed in preference to an underground winder installation. No. 2 ore shaft with borehole ropeways commenced lead ore hoisting operations in September 1938. Apart from the copper ore hoisted in the war years of 1943-46, lead ore was hoisted to No. 5 level until September, 1951.

Jan 1, 1988

Late Cretaceous and early Tertiary coals in the Greymouth, Ohai and Kaitangata coalfields represent a major national energy resource comprising-up to 2500 x 106 tonnes of coal in ground. The three coalfields are closely related in terms of age and sedimentary and structural character. The most striking feature common to all is the complexity of the geology which has severely restricted exploration and mining of these coal resources. This complexity is manifest in the irregular lensoid nature of coal seams and by the incidence of unpredictable medium and small scale faulting and folding. There are many geological similarities between these coalfields which are considered to arise from a common origin which can be related to the plate tectonic evolution of the southwest Pacific region. In order to efficiently assess and exploit these coal resources it will be necessary to know their geology in great detail. This can he achieved by increasing the understanding of the sedimentary and structural evolution of the coal bearing basins. This knowledge may be gained by the application of traditional (ie drilling, field mapping) and innovative techniques (ie high resolution seismic, in seam seismic) with on going research-oriented studies (ie basin analysis, coal petrography).

Jan 1, 1987

By Dunne R, Defilippi J

Dump leaching began at Teller in late-1988 at a rate of 4 MTPA and has been progressively expanded to the present rate of 10 MTPA. Teller's on-going commitment to dump leaching is driven by the amenability of gold ores to the process and the availability of large tonnages of low grade gold ore. The sequence of evaluating ores for dump leaching involves rolling bottle tests on coarsely ground ore, followed by small and large column leaching and finally trial heaps. Trial heap tests are very expensive and an alternative approach to this is large diameter column leaching.A four-column permanent facility was built at Teller to specifically evaluate the leaching characteristics of new dump leach ores. Details of construction, operation and dismantling are discussed in the paper. Capital cost for the four column facility was some $45 940, while operating costs are about $24 800 per column.

Jan 1, 1992

By Andersson PO

Boliden Mineral AB Boliden Mineral AB operates nine mines in Northern and Central Sweden, producing zinc, lead and silver concentrates and copper and gold. Seven of these mines use cut and fill (C&F) mining with a total production of 2 Mtonnes of ore per year.

Jan 1, 1998

During Gepp's lifetime, Australia was in the forefront of science and art in metallurgical practice. This did not come easily for although blessed with a unique mineral deposit at Broken Hill large in size and rich in values much courage and daring was needed in the development of processes whereby they could yield the best results.The resultant development of the flotation processes at Broken Hill is one of the most important inventions of the 20th century.

Jan 1, 1993

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

As part of a prefeasibility study being undertaken by Newcrest Mining Limited, the Cadia East Implementation Team has developed an access decline to the proposed underground operation. This paper describes new technologies that have been employed in this development, which include: high frequency drifters that have penetration rates one and a half times that of competitors, ensuring minimal increase in drill time, despite rounds greater than 5.5 m;automated drilling used in conjunction with laser navigation and face pattern design software, which facilitates exact positioning of hole collars, lengths and lookouts for accuracy and repeatability; andemulsion charging that reduces manual handling; has variable string loading capabilities, via its hose retraction system, for perimeter control and reduced fume characteristics. A Six Sigma improvement process was used to support the system change undertaken and demonstrated that development rates improved 60 per cent above the comparable single heading benchmark.

Jan 1, 2008

By Moy A. D

The Esperanza deposit is located 120 kin N of Mount Isa, Queensland at approximately lat 19¦20'S, long 139¦22'E on the Camooweal (SE 54-13) 1:250 000 scale map sheet. It is one of several structurally controlled copper ¦ cobalt deposits developed along the Mount Gordon Fault zone and related faults, within the Western Fold Belt of the Mount Isa Inlier (Figure 1). Together with the nearby Mammoth orebodies it forms the basis of the Gunpowder operation of Aberfoyle Limited. Until recently ore was mined from the Mammoth orebodies by open stoping with decline haulage to surface leach pads. Leaching of in situ broken ore (in place) and surface heaps, followed by solvent extraction and electro-winning (SX-EW), produced copper metal on-site. In March 1997, mining was suspended at Mammoth and the focus of the Gunpowder operation switched to development of the Esperanza orebody, which is expected to begin open cut production in mid 1998. SX-EW methods will produce 44 000 tpa of copper from an expanded plant. The pre-mining mineral resource at Esperanza (measured, indicated and inferred) is estimated at 4.6 Mt averaging 7.7 per cent copper.

Jan 1, 1997

The Drummond Basin is a large intracratonic basin which developed in central Queensland during Late Devonian to Early Carboniferous times. It is postulated that the Drummond Basin developed as a foreland basin, to the west of a probable west dipping continental margin volcanic arc and subduction zone. The Drummond Basin sequence has been s,ibdivided into three tectono-sedirnentary cycles. Cycle I forms the base of the sequence and comprises thick sequences of intermediate to felsic volcanics and proximal volcanolithic sediments. The volcanics, particularly in the northeast of the basin, occur in separate sub-basins around what were probably isolated eruptive centres. In contrast, the rocks of Cycle 2 and Cycle 3 have been deposited during episodes of broad, basin wide subsidence. Five major igneous episodes, some of which may be co-magmatic, are recorded in the eastern Drummond Basin and environs between the Late Devonian and the Early Permian. The first and second episodes occurred during the Late Devonian to Early Carboniferous and are represented by the volcanics in Cycle 1 and Cycle 3. The third episode involves the intrusion of granitoids of Early Carboniferous age into the Drummond Basin sequence. These occur in the Ukalunda area and are related to gold mineralisation at Ukalunda and Valhalla. Episode four includes the felsic volcanics of the Bulgonunna Volcanics. This episode does not appear to he broadly auriferous but gold mineralisation does occur in possible basal Bulgonunna Volcanics at Mount Coolon. The final episode includes a suite of granitic intrusives which intrude the Bulgonunna Volcanics and which are considered to be co-magmatic with them. These intrusives do not appear to be generally associated with gold mineralisation. Gold mineralisation is widespread in the north- eastern Drummond Basin and environs. It is probable that the gold mineralisation is concentrated in epithermal cells during the Late Devonian to Early Carboniferous volcanic cycles. This style of mineralisation appears to be related to tectonic setting in modern analogues.

Jan 1, 1989

By Mousset-Jones P, McPherson M. J

This paper explains and discusses a computer program developed to deter- mine the optimum combination of fan pressures that will give a required distribution of airflows in a mine ven- tilation system. The program is based on an existing simulator, VNETPC and two experimentally developed relationships: (1) linearity between fan pressures and added regulator resistances and (2) a non- linear convex function relating the system air power and the fan operating Pressures.

Jan 1, 1988

By G K. Robinson

The existence of bias in samples taken by cross-stream sample cutters has been investigated using three-dimensional discrete element method (DEM) modelling. Detailed quantitative information on overall extraction ratios, size specific extraction ratios, missed and extra sample components can be made by comparing a reference sample to the actual sample. A key advantage of using this modelling approach over physical experimentation is that the reference sample can be measured on precisely the same portion of the stream of material as the actual sample, thereby allowing the elimination of a significant fraction of the variability and allowing statistically significant results to be obtained using many fewer replicates. Quantitative analysis of results broadly supports the commonly-used rule that the cutter aperture should be at least three times the nominal top-size of the material being sampled, but does not support the commonly-used rule requiring increase in cutter aperture if the cutter speed exceeds 0.6 m/s. Sampler performance can be understood in terms of the balance of forces in the congested region of material formed by the slowing of the particle stream due to collisional interactions around the mouth of the cutter.

Jan 1, 2008

The output of Dexin Pit Copper is up to 33 million tonnes a year and the final depth is more than 500 m. As a cost reduction measure, the in-pit crushing and conveying system has was introduced to deliver ore from the pit to mills. This paper describes the in-pit crushing and conveying system, and highlights the optimum level where the shovel-truck haulage system transfers into In-pit Crushing and Conveying system, relocation of an in-pit crushing system, and includes the impact of the transferring point when the costs change.

Jan 1, 2003

By J, J M. Young, P T. Nielsen, R Zhu

Improved understanding of the variables that influence hydrocyclone performance is of increasing interest to the iron ore industry, where hydorcyclones are widely used to deslime fine ore. In many cases, the impact of particular variables is not quantified sufficiently well experimentally to ensure that industrial performance will match expectations. The current work focused on developing and implementing a systematic methodology to evaluate and compare the performance of four different hydrocyclones in a desliming application. A critical component of the project was the design and construction of a pilot-scale hydrocyclone rig using state of the art monitoring and sampling methods. A wide ranging test programme was conducted to quantify the effect on metallurgical performance of the key hydrocyclone variables such as pressure, feed density, vortex finder size, spigot size and hydrocyclone make/overall design. Details of the experimental approach are presented, along with a discussion of the sizing analysis methods used. Performance criteria were established to assess the four hydrocyclones. The effects of each major variable were quantified over a wide range of conditions. The results show that clear performance differentiation was achieved, enabling the selection of the optimum configuration. The results from this work demonstrate the benefit of objectively assessing the performance of nominally equivalent units in selecting an optimum configuration that best satisfies the performance criteria.

Jan 1, 2002

A Master of Applied Science degree course in Mining Geomechanics commenced in 1983 at The University of New South Wales, taught by extern- al (correspondence) studies. The course is aimed at graduates employed in the mining indust- ry, and especially people involved in geomechan- ics projects on a routine basis in remote locations. This kind of course is unique in Australia and is one of only two correspondence programmes available at this University. The author designed the course and nursed it through the early years, and was Director until 1986. The paper describes the teaching and assess- ment methods and also discusses aspects of admin- istration and coordination of such a course. It is concluded that an important need of the mining industry is being catered for and it appears that similar correspondence course for- mats would also be useful in other areas of the minerals industry.

Jan 1, 1986