Search Documents

By R Kahnt, S Jahn, D Baacke, M Eckart

Relocation into the Lichtenberg open pit mine of about 110 million m3 of sulfide-bearing and ARD-generating waste rock piled up on the surface is the most important and cost-intensive single surface restoration project conducted by WISMUT GmbH at the former Ronneburg uranium mining site. The waste rock comprises for the most part Palaeozoic shales, limestones and diabases with pyrite contents of up to seven per cent. Waste pile relocation began in 1992 and is scheduled to be completed by 2007. The approach used for relocation has been extensively described elsewhere (Jakubick et al, 1997; Hockley et al, 1997; Chapman et al, 1998; Paul, 2003). Following completion of the backfill that will be up to 60 m above the initial ground level, a dry cover will be placed on top of the backfilled mine wastes. The area to be covered amounts to about 220 ha. Design planning for the final cover placement of which is to begin in 2004 had to be based on a comprehensive cost-benefit analysis over and above compliance with legal requirements. The crucial question to be answered in this respect was to determine û in addition to the expenditure required to ensure reuse, radiation protection and soil protection û the extent to which additional time, effort and money were justified in order to minimise contaminant release from the unsaturated portion of the backfilled pit contributing to total releases into the ground water and possibly achieve savings in long-term operating costs for the on-site water treatment plant. Optimisation was based on contaminant balance modelling for the entire site reproducing dominant physical and geochemical processes. Among the specifics underlying the cover design is that contaminant release from the backfilled open pit must not be considered independently of that from the adjacent flooded underground mine and that a major part of the backfilled open pit will also be submerged. Following weighing of cover-related short- and long-term costs it was found that higher construction costs for the various cover options will not be offset by cost savings in the long-term water treatment. As a consequence of pit flooding, even a costly multiple cover including an impermeable layer will only insignificantly impact on concentrations and loads at ground water spill over points. As a result of comprehensive studies and investigations, a combined cover of cohesive soil material from on-site excavation overlain by a 0.4 m thick storage layer to restore natural soil functions for revegetation was derived and submitted for approval. Together with hydraulic measures, this approach is to meet any requirement in terms of radiology, water protection, stability, erosion protection, and reuse.

Jan 1, 2003

By H Waterer, L Zheng, T Kalinowski

The Hunter Valley Coal Chain (HVCC) consists of mining companies, rail operators, rail track owners and terminal operators, together forming the worldÆs largest coal exporting facility. In 2008, the throughput of HVCC was about 92 million tonnes, or more than ten per cent of the worldÆs total trade in coal for that year. The coal export operation generates around $15 billion in annual export income for Australia. As demand has increased significantly in recent years, and is expected to increase further in the future, efficient supply chain management is crucial. The Hunter Valley Coal Chain Coordinator Limited (HVCCC) was founded to enable integrated planning and coordination of the interests of all parties, thus improving the efficiency of the system as a whole. One of the many planning challenges faced by the HVCCC is that of annual maintenance planning. Different supply chain elements, such as trains, railway track, terminal equipment and load points, must undergo regular preventive and corrective maintenance, leading to significant reductions in system capacity (up to 15 per cent). However good alignment of the maintenance tasks can reduce their impact, and the HVCCC undertakes an annual process to ensure the impact of maintenance on the supply chain capacity is as small as possible. This is achieved in an iterative negotiation process between HVCCC and individual service providers. In the past, maintenance schedule optimisation was largely manual, which for the more than 1000 tasks involved is quite labour-intensive.In this paper the authors describe an approach developed at the University of Newcastle in partnership with the HVCCC to automate this schedule optimisation process. We will discuss our experience in applying exact (mixed integer programming) and heuristic techniques from mathematics and computer science to address the problem. This work is anticipated to lead to new decision-support tools for the HVCCCÆs capacity planning team.

Sep 26, 2011

Hindustan Zinc Limited (HZL) is one of the leading base metal producers in India. It operates a two-smelter Complex at Visakhapatnam, Andhra Pradesh. At this zinc-lead smelter zinc is manufactured by the conventional hydrometallurgical route and lead is produced by Blast furnace technology generating residues or wastes which contain substantial quantities of metal values. Disposal of such wastes is a problem in any non-ferrous industry. Both the stringent environmental regulations and the changing industrial scenario emphasise the need for industrial research to find economically viable and environmentally friendly technologies to recover the metal values from these waste materials. The in-house R&D Centre at Vizag Zinc Smelter (VZS) thinking globally re-engineered its activities and major thrust was given for converting waste to valuable metals and metal compounds. Basic analytical chemistry with the hydrometallurgical concepts has been adopted in developing these innovative technologies. In this paper attempts are made to provide a clear history of the different waste raw material, the process developed for each raw material and their superiority of over other parallel work. Most of the processes described here are pilot plant tested and under patenting. The process flowsheet, results obtained and advantages of each process are presented. This paper provides a consolidated approach through which the varied smelter waste materials can be processed with cost effective and eco-friendly innovative technologies. In-house R&D efforts at VZS with its contribution and achievement in converting æwastes into wealthÆ technologies are presented in this paper on the following the major thrust areas:recovery of zinc from liquid effluent; recovery of zinc from effluent treatment plant (ETP) gypsum sludge; production of highly pure electrolytic zinc metal powder from zinc bearing gypsum residue/sludge generated at the effluent treatment plant; hydrometallurgical recovery of copper as copper sulphate solution which can be used for CuSO4.5H2O, copper cathode/copper metal powder from copper-cadmium cement; recovery of manganese, lead and silver from anode mud generated at Zinc Cell House and 4-metal extraction/recovery of manganese, cobalt, copper and nickel from Indian ocean bed manganese nodules; recovery of zinc, lead, silver and sulphur values from silver concentrate residue generated at the froth flotation process; recovery of silver and lead as lead-silver sponge/lead-silver sulphide concentrate from lead bearing residues; recovery of lead, silver and copper from copper matte; recovery of antimony as antimony metal or lead-antimony master alloy from antimony bearing dross; and recovery of nickel and dimethylglyoxime from Ni-DMG complex.

Jan 1, 2000

Blasting has been the most frequently used method for rock breakage since black powder was first used to fragment rocks, more than two hundred years ago. This paper is an attempt to reassess standard design techniques used in blasting by providing an alternative approach to blast design. The new approach has been termed asymmetric blasting. Based on providing real time rock recognition through the capacity of measurement while drilling (MWD) techniques, asymmetric blasting is an approach to deal with rock properties as they occur in nature, ie randomly and asymmetrically spatially distributed. It is well accepted that performance of basic mining operations, such as excavation and crushing rely on a broken rock mass which has been pre conditioned by the blast. By pre conditioned we mean well fragmented, sufficiently loose and with adequate muckpile profile. These muckpile characteristics affect loading and hauling (Scott, 1996). The influence of blasting does not end there. Under the Mine to Mill paradigm, blasting has a significant leverage on downstream operations such as crushing and milling . There is a body of evidence that blasting affects mineral liberation (Djordjevic, N, 2001). Thus, the importance of blasting has increased from simply fragmenting and loosing the rock mass, to a broader role that encompasses many aspects of mining, which affects the cost of the end product. A new approach is proposed in this paper which facilitates this trend æto treat non-homogeneous media (rock mass) in a non-homogeneous manner (an asymmetrical pattern) in order to achieve an optimal result (in terms of muck-pile size distribution)Æ. It is postulated there are no logical reasons (besides the current lack of means to infer rock mass properties in the blind zones of the bench and onsite precedents) for drilling a regular blast pattern over a rock mass that is inherently heterogeneous. Real and theoretical examples of such a method are presented.

Jan 1, 2001

By S Yang, J Wang, J G. Ning

A series of conventional dynamic uniaxial compression (CDUC) tests and coupled static-dynamic loading (CSDL) tests were conducted using a split Hopkinson pressure bar (SHPB) system to explore the dynamic mechanical behaviour and fracture characteristics of medium sandstone on a microscale in the laboratory. In the CDUC tests, the dynamic uniaxial compressive strength of the medium sandstone was rate-dependent, while the dynamic elastic modulus was not dependent on the strain rate. Then, we proposed a generalised model to characterise the rate-dependent strength from 17.5 s-1 to 96.8 s-1. In the CSDL tests, with increasing initial pre-static stress, the dynamic elastic modulus and dynamic strength increased nonlinearly at first and then decreased. The results show that two classical mechanical types (ie Class I and Class II) are observed from the dynamic stress-strain responses of the CDUC and CSDL tests. By means of scanning electron microscopy (SEM), the micro difference of post-loading microfracture characteristics in Class I and Class II behaviour was identified. In Class I behaviour, intergranular fracture (IF) usually initiates at or near the grains, most cracks deflected along the grain boundaries, resulting in a sharp angular edge, then coalesces to the main fracture surface that splits the specimen along the direction of stress wave propagation. In contrast, Class II behaviour results from the combined IF and transgranular fracture (TF).

Nov 29, 2022

Drum winders have now been built to attain depths of 3000 m and more in a single lift in accordance with the South African Code of Practice SABS 0294, which was introduced at the time of the last hoisting conference in 2000. Since then, this code has not only been followed for several winders in South Africa but was also followed in deep mines in Canada. Design of winders and their braking systems are described in the paper. Koepe winders are in use for high payloads of up to 50 t and to hoisting depths of around 2100 m. As known, the stress range of the hoisting ropes is the key parameter for rope fatigue. However, as per the SABS Code of Practice 0294, relying on static design is not the answer to the question of where the limits are for Koepe installation. The paper describes factors that are recognised to have influence in rope life and suggests definition of new design criteria for friction winders in order to get viable solutions for high-capacity hoisting from deep mines similar to drum hoisting.

Jan 1, 2005

The geology of an area in north-western New South Wales, bounded by the South Australian and Queensland borders, latitude 32° S. and longitude 14° E. is discussed.The area involved includes sixteen 1:250,000 standard military sheets and covers approximately 96,000 sq. miles.The geology of the Willyama Complex is not dealt with but a small area of metasediments previously included in this unit is separated and a possible correlation with Precambrian to the east is suggested. Torrowangee Group sediments are described and the problem of nomenclature using a glacial implication is raised.Nine areas of proven Lower Palaeozoic sediments are considered and their relationship to the boundaries of the Bancannia Trough outlined. It is possible that some exposures not yet substantiated by fossil evidence may prove to be Lower Palaeozoic rather than Precambrian in age.The sediments of the Lachlan Geosyncline in the area of the Cobar massif are described and new concepts on the age and distribution of some of the established stratigraphic units are introduced. The absence of rocks of Middle Silurian age probably indicates the time of a major orogeny in this area.Lithology, thickness, and distribution of the Upper Devonian sediments is considered and some of the more recently found fish plate localities are listed.Mesozoic sediments occur in isolated areas of Lower Jurassic age and in the Great Australian (Artesian) Basin. A four-fold subdivision of sediments of the basin has been possible in some areas but lack of sub-surface information at present, precludes the possibility of correlation with the type sections in Queensland.Units in the Cainozoic are subdivided and a five fold subdivision of the Quaternary, at present being used throughout western New South Wales, is described.

Jan 1, 1969

By Z R. Guo, Y Qiu, X F. Wang

Mechanical damage leads to the increase of effective stress of sediments, and pore closure hinders the discharge of methane gas. Ignoring the influence of mechanical damage leads to an excessive prediction of hydrate gas production. Therefore, a fully coupled model considering mechanical damage-chemical decomposition-gas-water two-phase seepage-temperature was developed in this study, and the model was verified by Masuda experiment. Based on the fully coupled model, the temporal and spatial evolution of the whole process of hydrate decomposition under the influence of three initial absolute permeabilities, three pressure drops and three water saturations were considered. The results showed that: • The gas production rate reached the peak value in a short time after depressurisation, and the peak value increased with the increase of the absolute initial permeability. The larger the initial absolute permeability was, the faster the damage variable reached the peak value. The porosity increased gradually before the damage variable reached its peak, and the gas flowed more easily. • When the pressure drop was low, the hydrate remained stable in solid form. As the pressure drop increased, the hydrate gradually began to decompose. The greater the pressure drop was, the faster the initial decomposition rate of the hydrate was. So the damage variable increased rapidly and the porosity increased continuously, resulting in a large gas production rate at the initial stage of decomposition. • The larger the initial water saturation was, the smaller the effective stress wss, resulting in the slow growth of the damage variable and the small change of porosity.While the gas relative permeability was small, it resulted in a smaller gas production rate, and hydrate decomposition was slower. • The damage variable showed a process of rapid growth first, then slowly increased to the peak, and then gradually decreased to a stable state. When the damage was considered, the hydrate decomposition time to the steady state was longer, and the gas production was about 80.68 per cent of that without considering the damage.

Nov 29, 2022

Anodic stripping voltammetry is an analytical technique which has established some popularity for trace analysis of metals because of its sensitivity, selectivity and capability for simultaneous analysis of some elements. The technique can be readily adapted for field use because of its relative simplicity and low power requirements. This paper describes a relatively new instrument, the Portable Digital Voltammeter, developed by CSIRO, which utilises the glassy carbon electrode in a novel cell design and provides parts per billion (ug/L) sensitivity in an instrument which can be field operated. Ten elements, Zn, Cd, Tl, Pb, Cu, Sb, Bi, Hg, As and Au can be routinely analysed. Many of these elements are of interest to the mining industry, and to exploration geochemistry in particular. Case histories where the instrument has been successfully employed for stream and stream sediment analysis of Cu and Pb, for soil surveys of Cu and Au, and for Au in stream sediments and drill chips indicate there are advantages in having on-site data, during Exploration.

Jan 1, 1987

By Chapman RL

A new process has been developed to remove the impurities copper, cadmium, cobalt and nickel from a zinc plant electrolyte by cementation on zinc dust. The process has been tested in the laboratory and in a continuously operated pilot plant. It has been found that cadmium, in the presence of small amounts of antimony in solution, assists the removal of cobalt. Cementation is conducted in two stages: the first stage for removal of copper with a small excess of zinc dust to produce a relatively high grade product, the second stage for removal of cadmium, cobalt and nickel by addition of zinc dust in the presence of anti- mony. The excess zinc and the cadmium present in the second stage cementate can be selective- ly recovered by slow leaching in spent electrolyte. Zinc dust processes in use elsewhere are described and compared with the present system for use in the Risdon circuit.

Jan 1, 1984

By P K. Seccombe

The McKinnons gold deposit is hosted by weakly deformed, Palaeozoic metasedimentary rocks of the Cobar Basin in the western Lachlan Fold Belt of New South Wales. Mineralisation comprised a largely supergene resource of 1.7 Mt of ore, grading 1.7 g/t gold, established over structurally controlled, primary gold and base-metal mineralisation in underlying, carbonate-rich meta-siltstones and sandstones of Early Devonian age. Mineralisation was associated with at least two major fluid cycles. The first cycle was characterised by four stages of vein formation. Early quartz and carbonate veins (Stages 1 and 2) and quartz-pyrite breccias (Stage-3) occurred prior to, or early in, the main regional deformation (D1). Continued D1 deformation produced syntectonic, carbonate-base-metal veins (Stage-4), primarily in dilatant zones adjacent to fold axes. The second cycle of mineralisation was an epithermal-style event, driven by a shallow, syn-D2 or post-tectonic intrusion, defined by aeromagnetic imaging. The intrusion may have exploited a jog, controlled along the basin margin by basement faults. Mineralisation produced gold-pyrite veins, associated with pervasive quartz-sericite-adularia and chlorite-sericite alteration. Highest primary gold grades are confined to quartz-adularia boiling zones. The McKinnons deposit offers an important example of mineralisation formed by multiple processes. Early-stage, base-metal mineralisation at McKinnons reflects structurally focussed, basin dewatering and metamorphic processes, typical of other deposits in the Cobar Basin. By contrast, late-stage gold mineralisation at McKinnons is magmatically driven and of epithermal style. Recognition of overprinting distinctive geological events is critical, not only in modelling ore formation, but in developing a versatile exploration concept.

Jan 1, 1999

By M, C Silveira, C Ellice, D Christensen

Peak Gold Mines (PGM), a member of the Rio Tinto Group, is an underground and open cut gold mining operation located near Cobar, NSW. A multi-phase study was initiated in 2001 in support of developing a dry æmoisture store and releaseÆ cover system design for the PGM tailings dam, which contains potentially acid-forming tailings material. The first phase consisted of characterising the tailings and potential cover material (waste rock from an open cut operation) as well as soil-atmosphere cover design modelling. The second phase involved construction of two cover system field trials on the tailings dam and installation of a variety of field instruments to monitor the hydraulic performance of the test covers during all seasons of the year. Field performance monitoring commenced in April 2002 and will continue for a minimum of two wet-dry climate cycles (third phase), prior to using the field data for calibration and subsequent validation of numerical models developed for the cover system trials (fourth phase). This paper describes the work completed for the first two project phases and also discusses the initial performance of the cover system trials.

Jan 1, 2003

In the past two decades the global metalliferous mineral industry has trended away from pyrometallurgical (pyromet) and towards hydrometallurgical (hydromet) technologies including biometallurgical (biomet) processes. Pyromet, biomet and hydromet technologies have all developed considerably over this period. New projects have been biased or directed by legislation towards supposedly cleaner and greener hydromet and biomet technologies. The environmental cost and energy cost of pyromet production processes for copper and cobalt are compared with comparable hydromet processes using Life Cycle Assessment (LCA). The æreal costÆ of the global warming obsession and negative public perception of pyrometallurgy include greater carbon dioxide emissions and energy consumption per unit, associated with current hydromet technologies. Specific examples for copper and cobalt produced via the different routes are provided. The poor science involved with the global warming hypothesis is discussed. The use of LCA with sensitivity analysis as a decision making tool for mineral processing projects and technology developers is discussed.

Jan 1, 2004

Transport Canada (Federal Government) constructed the Halifax International Airport (HIA) near Halifax, Nova Scotia, Canada in the late-1950s. Site location criteria were primarily; direct access to the city and a raised flat topography. Unfortunately, the site chosen was located on shallow Meguma group pyritic slate bedrock. In 1982, during the construction of an airport taxiway, it became very apparent that acidic run-off from excavated bedrock at the site was having a negative impact on adjacent aquatic habitat. The ensuing 20 years involved many efforts to rectify the acidic drainage problem with mixed results. Some of the techniques which have been implemented at HIA to address the acid rock drainage (ARD) issue include: dry covers, wet covers, wetlands, electrochemical treatment, open limestone channels, limestone gravel polishing beds, agricultural limestone application, and two hydrated lime [Ca(OH)2] addition treatment plants, the first producing low density sludge and the new one that creates high-density sludge. Based on over 20 years of water quality monitoring data it is apparent that only certain acid drainage mitigation methods have been effective at HIA. In 2000 when the Halifax International Airport Authority (the Authority) took control of the operation and management of the airport, including the ARD issue, it was decided to construct a modern, highdensity sludge, hydrated lime treatment system. This new $CAN 7 million system is now in operation and is achieving compliance with water quality guidelines. Due to high operating cost, a review of methods to optimise the system is being carried out. The HIA ARD problem, though minor by comparison to most mine sites, has provided unique challenges and may provide valuable insights into this urgent environmental and financial issue.

Jan 1, 2003

By A Quigley

The Northside Storage Tunnel Project in Sydney includes over 20 km of TBM driven tunnels, over 3 km of declines and major caverns and pump rooms. The paper describes methods used for design on the project. Emphasis is given to the refinement of the use of empirical rock mass classifications, and to the use of discontinuum numerical methods.The use of empirical rock mass classifications in Sydney sandstone has usually led to conservative design because the systems are based on a random orientation of joints in the rockmass. Because the joint sets are usually oriented in a way that is beneficial for tunnelling, limits must be placed on the parameters used in the classifications system. The paper discusses these limits and the derivation of the parameters.The use of numerical methods in Sydney sandstone is discussed. Continuum methods have their uses, but discontinuum methods are preferred. The use of UDEC has been validated against a previous project, the New Southern Railway. Recommendations are given for UDEC models.

Jan 1, 1999

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

Sampling and sample preparation systems at the Hamersley Iron Pty. Limited port of Dampier, W.A., were developed for two separate objectives. 1. The need for rapid determination of physical properties. On stream size analysis enables lump ore and pellet- ized ore physical properties to be monitored and controlled whilst shiploading is in progress. As a control procedure this facility allows optimum shiploading rates con sistent with physical quality control. 2. The need for accurate chemical analysis. Chemical analysis on ship- loading forms the final link in overall quality control procedures encompassing the operation of mining, railway and port blending. Thus maintenance of specification products with minimum variation in chemical characteristics is ensured.

Jan 1, 1976

By Holcombe R. J, Dobos S. K, Little T. R

Blue amphibole-bearing rocks in the North D'aguilar Block of southeast Queensland occur either as relict pods and lenses within regionally extensive greenschist facies phyllites and schists or as blocks entrained in serpentinite-matrix melange. Epidote + crossite-bearing varieties predominate and formed under conditions consistent with underplating and high P:T metamorphism in a subduction-related tectonic environment. Neither lawsonite nor jadeite has been observed and metamorphic conditions are estimated at 380-4500C for pressures of 0.5-0.8 GPa. High P:T metamorphism occurred during the earliest stages of deformation and was superimposed upon protoliths of inferred Late Devonian - Early Carboniferous age, including mafic volcanics, tuffs and coarse volcaniclastic breccias as well as pelagic and henipelagic sediments, all of which have undergone varying degrees of over-printing to the greenschist facies. Greenschist facies metamorphism occurred during the second phase of deformation and was associated with the formation of mainly flat-lying or subhorizontal structures; it followed the cessation of subduction and occurred in response to either thermal relaxation during uplift or the imposition of regional heating induced by crustal thickening and/or synkinanatic granite emplacement. Uplift and cooling of the high P:T rocks was completed by 260-265 Ma and may have occurred in response to the same extensional processes which gave rise to the onset of rifting in the adjacent Esk Trough.

Jan 1, 1990

By G Lane, S Morrell

The design of the 12 m diameter SAG mill installed at the Cadia Hill Mine in New South Wales followed after two years of extensive laboratory and pilot plant testwork. The testwork showed the Cadia ores to be hard and competent necessitating the use of both a variable speed SAG mill drive and pebble crushing. The grinding power requirements for the SAG mill was based on engineering in-house grinding software, pilot plant data and simulations using JK SimMet software. Surveys of the SAG mill operation during the first four weeks showed the feed size distribution, transfer size and pebble rate to be lower or less than those for which it was designed. To compensate for the lower pebble rate, the SAG ball load was increased. This resulted in the total comminution circuit power being some 0.5 kWh/t higher than predicted. The JK SimMet SAG model has been modified to take account of these variations.

Jan 1, 2000

Mining projects have long since presented challenges for the protection of the water environment. Lessons learnt from historical pollution incidents and increasingly stringent environmental controls have significantly improved the environmental performance of mines in developed countries. In contrast, water protection legislation and guidance in the Former Soviet Union (FSU) countries, based on the æpolluter paysÆ principle, has not promoted the prevention of water pollution, and examples of poor environmental performance in mining still exist. However, there is now evidence of emerging legislation encouraging the protection of the water environment. This paper provides an overview of water protection legislation in the Russian Federation and Armenia and highlights some of the challenges facing international mining companies developing projects. A mining case study is described, which highlights how communities in Armenia increasingly value their water environment. Here, greater public participation in development projects is playing a vital role in influencing water protection legislation. It is considered that public opinion and emerging legislation will increasingly present challenges for the development of mining projects.

Jan 1, 2006