Search Documents

Several coal preparation plants are presently "automated" to the extent of automatic sequencing and interlocking via digital means, together with closed loop control on various level and density circuits. This paper will explore the potential for second generation automation utilizing on-stream ash analysers and other measuring elements so as to optimize the total metallurgical process. This would enable maxim-ization of recovery, improved product homogeneity and minimum reagent consumption.

Jan 1, 1985

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By Sims D. A

This paper primarily describes the application of geology to the different mining methods employed in a large underground mine. The steeply dipping stratiform Silver/Lead/Zinc mineralisation at Mount Isa include up to 28 mineable orebodies. The orebodiea are mined by cut and fill, sublevel benching and sublevel open stoping; the method chosen depending mainly on orebody geomechanics.The sources and methods of data collection, and the interpretation process undertaken, are described. The paper emphasises the different geological input required, by each individual mining method, to provide the necessary production and strata control. This input contributes significantly to the success and efficiency of the operations.

Jan 1, 1990

By Morrison R. D, Kojovic T

Industry-sponsored research at the Julius Kruttschnitt Mineral Research Centre has produced models of high tension roll and electrostatic plate separators operating in mineral sands dry plants. The behaviour of mineral species has been characterised under a wide variety of operating conditions by extensive plant machine sampling and laboratory measurements. The effect of operating conditions on separator performance has been quantified by monitoring changes in the weight distribution of mineral species along the product splitter axis. The response of each mineral species has been modelled on a size-by-size basis using an average surface charge decay time and a variation in its surface properties. The models incorporate changes in machine, mineral and ambient conditions on the separation and predict all product flows, assays and size distributions. This paper outlines the structure of the models. These models are being implemented in JKSimSand, an user-friendly simulation software Package.

Jan 1, 1991

By Yoon R-H, Luttrell GH

A theoretical model has been developed to predict the probability of particle collection by air bubbles in a quiescent flotation pulp. The model considers the effects of both hydrodynamic and surface chemistry forces acting during the bubble-particle interaction. Hydrodynamic forces considered include the gravitational, buoyancy, streamline and film thinning resistance forces. The surface chemistry forces considered include the electrostatic, dispersion and hydrophobic forces. The hydrophobic force has been estimated from extended DLVO theory. The model is capable of predicting hydrodynamic and surface chemistry conditions under which bubble-particle adhesion is possible. Validity of the model has been verified experimentally.

Jan 1, 1993

By Koppe J. C, Dimitrakopoulos R, Costa J. F

Grade control and the delineation of ore/waste in open pit operations is traditionally based on the comparison of estimated grades with an economic cut-off. This paper deals with an alternative approach to grade control based on estimating gra

Jan 1, 1998

By Teague JWS, Jung RF, Kadletz O, Jones DR, Jones CJ

A study of the passive treatment system for Hilton minewater revealed that it consists of four main process steps. The water, which contains soluble and particulate iron and zinc and is supersaturated with CO , is pumped to the surface and then passes throuqh a degassinq unit into settling ponds where larger particles of iron hydroxide, containing some adsorbed zinc, can settle out. The still turbid supernatant is pumped to the top of a hill, from where it is allowed to trickle in a broad sheet, releasing CO , towards an earthen channel in the valley below. Consequently the pArises from around 6 to 7.5. This in turn promotes further decrease in the concentration of soluble zinc by increased adsorption of zinc on to iron hydroxide particles. The channel then transports the water to the third process in the system - a 53 ML pond acting primarily as a flocculation-sedimentation basin. The clarified water overflows into a second channel, downstream of the pond, which constitutes the fourth process in the system. Here, copious quantities of filamentous algae further reduce zinc concentrations to acceptable levels before the water is collected for recycle into mine operations. The work reported here represents a detailed study of this system and describes the optimisation of the operation of each of the individual steps involved.

Jan 1, 1988

**Add abstract here**

Jun 1, 2010

By De Janti VP

The automation and centralized monitoring of longwall type underground mining is presently an important subject matter of research in France. The purposes are :to improve safety and working conditions to increase productivity.to improve efficiency in machine operation through continuous "health monitoring". to make winning possible in difficult seams.

Jan 1, 1985

A typical large surface mine in Scandinavia has hard rock, a cold cli- mate, poor ore, a complicated vein type orebody and high labour costs. In order to survive, these mines have to maximise their ore production, minimise waste extraction and get the most out of every man hour. This article describes two examples of how inclined blastholes drilled with hydraulic percussive drills can help to meet these requirements. Both of these Scandinavian mines, Kemira Ltd's Siilinjarvi mine in Finland and Sydvaranger A/S's Bjornevattn iron mine in Norway, use inclined blastholes of 200 mm in diameter. The Siilinjarvi quarry is using inclined holes in production drilling. The Bjornevattn iron mine is blasting the final pit walls with inclined holes. The benefits gained when using inclined instead of vertical blastholes are better selectivity, better bench drilling conditions, steeper final pit walls and increased safety.

Jan 1, 1989

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June, 1,,896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to -the works, the firewood being of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides).The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall. The areas so far exploited aggregate a total of about 42 sq. 'miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cub. ft. per ton, 60 tons per acre being considered a good average yield. The gross amount of firewood handled during the past 13 years approximates 1,200,000 tons, the greater portion of which has been obtained by ordinary tramming methods. The company's main line of railway, 3-ft. 6-in. gauge, has served as a trunk line for all supplies derived from the Queen River valley, south of the reduction works, while the northern and western areas have been exploited by means of...

Jan 1, 1911

The integration of historic exploration geoscientific data with high precision multi-element and isotope geochemistry can provide explorers fundamental information on mineral potentiality, tectonic setting, source signatures, fluid migration, mineralisation environment and the timing of mineralising events. Such knowledge is crucial for ore modelling and target generation, particularly for concealed ore systems in both brown and greenfields. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Underground mines in Australia and worldwide are extending to greater depths. The effect of depth brings a number of challenges to mining engineers including geotechnical, ventilation, haulage and selection of mining method. The main effects of depth from a ventilation perspective are increased heat and humidity leading to reductions in productivity, occupational safety and health issues and the potential for fatalities. Numerous approaches have been undertaken over the years to mitigate against these effects. In this paper a review of various approaches to improving climatic conditions at a number of mine sites worldwide is undertaken. From these case studies it is argued that for mines at depth with the potential for a climate problem perhaps an alternative design philosophy to the established design philosophy should be utilised. In conclusion, the paper proposes some simple rules of thumb for use in mines with climate problems or the potential for climate problems.

Jan 1, 2008

By Jena P. K

Smaller deposits of high grade chalcopyrite or the concentrates of low grade and complex copper bearing ores, can be subjected to extraction processes other than smelting and converting. Low temperature chlorination and segregation processes are among those mentioned in the literature. In the present work, extraction of copper from a Brazilian chalcopyrite concentrate by slurry chlorination with chlorine gas at room temperature, dry chlorination by chlorine gas in the temperature range of 350 to 450¦C and segregation roasting of the calcined concentrate in the temperature range of 650 to 800¦C have been carried out. The effect of several experimental variables on the extraction of copper has been discussed in all these cases. Under optimum experimental conditions, 100 per cent Cu extraction was possible by either slurry or dry chlorination processes and around 86 per cent Cu by segregation roasting. For all the three cases, possible methods have been suggested to trial the studies on a pilot scale to assess their technoeconomic viability.

Jan 1, 1992

Diamond drilling is a relatively new commodity in terms of drilling. The first known diamond drilling activities were carried out in the Swiss Alps around 1863 when the Swiss engineer M Leschot designed and made a tube with a diamond set face which was used in probing ahead drilling for the Mont Cenis tunnel (Figure 1). Craelius AB which today is a part of the Atlas Copco Group was formed in 1886. The name Craelius is a family name and the founder of the company was Per Anton Craelius (Figure 2). He went to the United States to study this new technology using diamonds to extract core samples and when he returned to Sweden designed his first diamond drilling machine. It was a man-powered drill needing a crew of six men, two to crank the unit, one to feed, two to power the flush pump and a foreman (Figure 3). As time passed through research and development, the original design was improved and manpower was substituted for steam engines and later combustion engines or electric motors (Figure 4). During the 1930s the drills radically changed designs and took the form of the short stroke drills which to a certain extent are still in use today. The original design of these drills have been refined during the years, hydraulic chucks, gear boxes and other improvements have been added.

Jan 1, 1995

The optimization of management structure systems for coal mines is undertaken with the use of economic and mathematical models of the monitoring, manufacturing, and functional subdivisions of the systems. The main para- meter to be minimized is economic loss result ing from organization faults and this is achieved, in part, by optimum distribution of both technological objects and engineering and technical personnel. Models used are of the "gated" type, parameters for which are derived from analysis of manufacturing processes and from automatic information systems. The use of these models ofmanagement structures is only part of the process of optimization of those structures for coal mining operations.

Jan 1, 1977

By B N. Morrison

In all metallurgical plants metallurgists require analyses of the various intermediate products, eg flotation feeds, flotation concentrates, tailings, mattes, slags, etc to monitor the efficiency of the plant processes and for plant control purposes. Traditionally these samples have gone to off-site laboratories and there can be some considerable delay before analytical data are received. On-line monitors have to be used for plant control purposes and these are difficult to maintain and can give poor quality data. Recent technological advances in automation in analytical laboratories now allow a far quicker turn-around time for analytical data so they can be of more use to the metallurgist. Automation, which involves the use of robots and fewer people in laboratories, has the added benefit of providing higher quality data as the possibility of human error and bias is minimised. Differences between conventional manual laboratories and automated laboratories are described. Automated analytical laboratories are now becoming the laboratories of choice for mining companies which require large numbers of samples to be analysed on a 24/7 basis on similar sample types using the same sample preparation methods and analytical procedures. Automated laboratories have now been installed in platinum, iron ore, copper and aluminium producing mining companies. A further advantage to metallurgical plants is now the possibility of siting automated analytical laboratories in-plant and designing the plant around the laboratory. Concentrator streams, slags, etc can be sampled by automated samplers, the samples transferred by automation to the in-plant laboratories and all sample preparation and analyses carried out by automated processes. These laboratories require a minimum of staff. Such automated in-plant laboratories have been installed on a platinum mine flotation plant, a platinum mine smelter and steel plants. One is in process of being installed on an iron-ore mine with the sampling being carried out by an automated sampling tower. The procedures followed in planning an automated analytical laboratory for a metallurgical plant are described in detail in the paper. The platinum plant smelter automated system which includes rapid transport of samples by air-tube to the laboratory for the analysis of the samples by XRFS is also described in the paper. It is concluded that automated analytical laboratories can be retro-fitted to most metallurgical plants but they are best suited to greenfield sites.

Jan 1, 2008

A comprehensive understanding of the rocks associated with coal seams, and also of the coal itself, is essential in assessing the likely behaviour of the materials before, during and after the mining process. The nature of the rock materials involved in coal mining can give rise to risks from adverse geomechanical properties, create problems in coal quality control and produce difficulties with environmental impacts, all of which may affect the profitability, impact and safety of the operation. Examples of issues associated with rock composition include slaking and degradation leading to roof, floor, pit wall or spoil pile instability, ignition of methane in mine atmospheres by frictional processes, liberation of quartz-rich dusts into ventilation systems, production of coal with unfavourable preparation or marketing characteristics, and escape of suspended solids or potentially toxic leachates from spoil piles and other types of emplacements. Methods for evaluating rock composition include microscopic examination, chemical analysis and X-ray diffraction, with the latter being especially useful for fine-grained rocks or for clay-bearing materials. Other techniques, such as geomechanical testing and down-hole geophysical logging, are also useful, but give less direct information about the actual composition of the materials involved. Indeed, understanding of rock composition, through microscope or quantitative X-ray diffraction studies, provides a basis for checking information from other sources, explaining different aspects of rock behaviour, and an essential link in relating geophysical or geotechnical data to broader-based geological models as part of the risk assessment process.

Jan 1, 2003

Geologists working in mountainous terrain were the first to map and interpret in three dimensions and as a result, made the first contributions to our understanding of mountain building and structural geology. However, geology during the 1900s has been dominantly a two-dimensional exercise in data gathering and interpretation. The standard output of geological surveys and university research has been the geological map and the standard methodology of the mineral explorer has been surface mapping and prospecting. The future will be concerned far more with the third dimension.

Jan 1, 1993