Search Documents

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By A C. Robertson

Studies by Tennent, Isokangas Pty Ltd (TIP) have indicated that underground quarrying of backfill may be a cost competitive option for providing backfill for specialised situations in underground mining. Situations where suitable bulk fill material may not be available on the surface, and where the total cost of setting up a fill distribution system are prohibitive, could favour the mining of fill material underground adjacent to the stopes being mined. Considerations include environmental impact, scheduling, surface constraints and total costs. The examples quoted in this paper, and the case studies are based on the authorsÆ personal observations and experience.

Jan 1, 1998

By R Berry, J Hunt, T Kojovic

Geometallurgy aids the understanding of orebody variability through the integration of geological and processing information, thereby enabling spatial mapping of processing (eg comminution or separation) performance across a deposit. In order to do this, estimates of quantitative geometallurgical attributes are needed so that continuous downhole profiles can be generated for each attribute, providing vital data for the development of processing domains through geostatistical modelling. However, as traditional comminution tests are high cost and/or require large samples, current practice typically results in insufficient data density and distribution of comminution indices making it difficult to model and map deposit scale variability. The aim of this work was to find a method to estimate comminution indices based on data that is widely available at mine sites. This data includes mineralogy and chemistry of drill core samples, plus logging information such as lithology and alteration. Work to date indicates that comminution parameters such as semi-autogenous grinding (SAG) Power Index (SPI), Bond Work Index (BWI) and A*b (Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight test (DWT) Index) can be modelled using chemical and/or mineralogical data. The estimated hardness indices can then be propagated into the mine site database and used in the definition of processing domains that map inherent variability across a deposit. The estimates can thus provide geometallurgical inputs for spatial modelling, mine planning and optimisation initiatives.CITATION:Hunt, J, Kojovic, T and Berry, R, 2013. Estimating comminution indices from ore mineralogy, chemistry and drill core logging, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By V Kumar, A S. Venkatesh, R K. Upadhya

The enormous iron ore deposits of eastern India are part of the volcano-sedimentary basins containing iron and to some extent manganese deposits that belong to the Iron Ore Group (IOG) of Archaean Singhbhum Craton, occurring as western and eastern limbs of a broad synclinorium. The eastern iron basin contains typically huge amounts of blue dust and powdery ores. There is a remarkable difference between the western flank ores and the eastern flank ores and the present study is part of the eastern flank ores from Noamundi. Demand for sintered fines as blast furnace feed coupled with the higher export price for lumpy ores that produce enormous amounts of fines during processing has created a situation whereby both primary and secondary fines, such as classifier fines, are being increasingly used as sintered feed for blast furnace. Systematic mineralogical and geochemical characterisation indicates that in many cases the ROM and classifier fines have to be processed to increase their Fe content and at the same time reduce their Al, Si and P contents. The fines which are already at micron sizes are amenable for beneficiation using the Mozley mineral separator and sink float test. It was observed that beneficiation was better and significantly greater by the sink float method than the Mozley mineral separator. Mineralogical and chemical studies of the fines reveal that around 80 per cent of alumina bearing minerals (gibbsite, clay and silicates) are present in the liberated form. Microscopic studies confirmed that the iron minerals are well liberated by controlled grinding to -300 mesh sizes with the beneficiation of iron ore fines and low-grade ores carried out using the Mozley mineral separator and sink float test. Beneficiation using the Mozley mineral separator increased the grade of concentrate with increasing flow rate of water as well as increase in amplitude of oscillation of the tray, but not very significantly with the increase in slope of the tray. In this method, though, iron concentration improved from 47 to 63 per cent with a recovery of around 67 per cent. It is not suitable for industry scale operation as only a small quantity of ores can be handled at a time. Beneficiation using the sink float test produced a better result with the Fe content increasing from 47 - 49 per cent to 66 - 68 per cent with a recovery of approximately 58 per cent. Initial feed Al2O3, SiO2 and Fe contents of 9.85 per cent, 15.3 per cent and 49.8 per cent respectively were beneficiated to 2.13 per cent Al2O3, 1.5 per cent SiO2 and 67.5 per cent Fe in the concentrate, with a recovery of 54.1 per cent. In contrast, using the Mozley table resulted in beneficiable contents 66.3 per cent Fe, 3.01 per cent alumina and 2.05 per cent silica. The combined alumina and silica content for the Mozley Table was >5 per cent, which exceeds the industry requirement of

Jan 1, 2005

By K Nesbitt

Draw control at Premier Mine is considered important to avoid conditions of isolated draw, which results in early waste ingress, compaction of the kimberlite ore and loss of ore reserves. The Premier Mine kimberlite pipe is unique in that the pipe is cut at a depth of 400 metres below surface by a 75 metre thick gabbro sill. All cave mining at Premier is below the sill and failure to exercise good draw control could cause early ingress of gabbro waste. Gabbro causes problems in the diamond recovery plant and the amount of gabbro sent to the plant needs to be closely monitored. Fortunately coarse gabbro fragments are easy to recognise in drawpoints. It was anticipated that only 85 per cent of available ore would be drawn from the blocks immediately overlain by the gabbro sill before excessive gabbro waste forced the closure of drawpoints. Data on tons drawn per drawpoint and loaded per LHD as well as the tons tipped per pass is gathered by the vehicle monitoring and control (VMAC) system and information recorded by the load-haul-dump (LHD) drivers. Draw control staff monitor drawpoints on a shift basis and record the occurrence, type and height of hang-ups. Information pertaining to the status of the drawpoint in terms of support, waste and availability is also recorded. A database has been compiled that has been used to analyse the overall pattern of draw control, the frequency of occurrence of different types of hang-ups, secondary blasting efficiencies and drawpoint and LHD productivity. The gabbro sill has provided a unique marker horizon that has allowed the arrival of rock from a level 100 metres above the production level to be recognised. Data shows that ore migrates extensively towards groups of drawpoints that are heavily drawn with many drawpoints more than 100 per cent drawn before gabbro waste was recognised. This indicates that an accurate mixing algorithm is essential for good draw control. Data on tons drawn, drawpoint availability, productivity and the occurrence of various types of hang-ups has allowed better control of the mining operation and provided data for planning future caves. In the BA5 mining block a drawpoint spacing of 22 metres, horizontally across the major apex, has still allowed drawpoints to be pulled to waste with no loss of ore. In the BB1E mining block the drawpoint spacing has been increased to 23 metres and no problems have been experienced to-date. Future initiatives centre on improving the data gathering integrity of the vehicle monitoring and control system and a linear programme that will optimise draw control and productivity.

Jan 1, 2000

By D Pearce

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By H A. Linn, K Winn, C W. Lee

The Q-slope method for rock slope engineering was developed to enable engineering geologists and rock engineers to rapidly assess the stability of excavated rock slopes in the field and make optimal adjustments to slope angles as rock mass conditions become apparent during construction of road cuts or benches. An empirical relationship between Q-slope and long-term stable slope angle is now supported through over 500 cases studies from Asia, Australia, the Americas and Europe. This paper presents about the stability analysis by first-ever applying Q-slope method on abandoned quarry wall in Singapore. The 30 m high rock slope which is composed of monzogranite rock was severely damaged by blasting operation. As the rock slope is intended for public view the objective was to retain the natural outlook and without any artificial support application thus manual scaling was carried out to clear the loosed rock blocks. In the end stable slope angle of clean rock face is determined once again by Q-slope method.

Nov 29, 2022

A new plant for grinding limestone was built at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited to meet increasing process demands expected to reach 150 tonne/day of ground limestone. Plant specifications included open- circuit wet grinding, a single ball mill, a feed sizing of minus 6 Tyler mesh, a product sizing of 100 per cent minus 200 and 95 per cent minus 325 Tyler mesh and for the plant to be unmanned during normal running. Main features of plant and equipment are described; grinding performances given, as well as operating experience since commission- ing of the plant in March, 1976.

Jan 1, 1977

By M A. Vinokurova, V M. Mullov

Due to treatment of refractory carbonaceous low-grade gold ores a new technology providing improved precious metal recovery is required. For this reason, a technology including gravity, flotation, recleaning of the flotation concentrate, intensive cyanidation of the gravity concentrate and carbon in leach (CIL)-process for intensive cyanidation tailings and the recleaned concentrate was developed. The proposed technology allows to decrease preg-robbing activities of concentrates treated by subsequent cyanidation. Total gold recovery by the proposed technology from the ore with a head grade of 0.8 g/t was 83.9 per cent. The gold loading onto the activated carbon from CIL process was 6.500 g/t.

Jan 1, 2007

By K Kuganathan, Y Potvin

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: a minimum filling rate of 250 m3/h, a curing time of 28 days, and minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A.G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue- gases, the circulating fluid bed technique with internal oil combustion at 2.2000 F for the calcining step and 'a five-stage fluidized bed cooler for heat recovery from calcines, the process gives an outstanding heat- efficiency. In a first industrial plant for 560 sh. t. alumina per day heat consumption figures of less than 1.400 BTU/lb A12O3 were achieved.

Jan 1, 1971

During the life of a mining project in Papua New Guinea (PNG), the greatest impact is on the people of the project area and the most intense, day-to-day contact is between these people and the project's field staff. Yet formal structures at present emphasise contact between much higher levels of national government and company personnel. Whilst understandable, this is unfortunate particularly since, given the nature of PNG politics, villagers do have a powerful influence on project success, as recent dramatic events on Bougainville have indicated. A greater role for local views and greater attention to such views by other parties is clearly required. But to achieve a successful marriage between informal village politics and the formal structures of investment procedures will require considerable patience and adjustment. This should be reflected in the cost of project development and be regarded as being as of a significance equal to that currently accorded to the technical aspects of project development.

Jan 1, 1990

Hamersley Iron Pty. Limited has maintained an interest in the screening of iron ore fines (nominally -6 mm). However, no dry screening process had successfully demonstrated acceptable separating efficiencies at high tonnage rates, low operating costs, and mechanical reliability when screening iron ore fines (containing up to 6% free moisture) at sizes of around 1 to 2 mm. A new type of vibrating inclined screen has recently been developed which is claimed to have a non-blinding screening surface. It was decided to test a pilot scale unit in an existing pilot plant located at Hamersley's facilities at Dampier, Western Australia. The appropriate operating parameters such as vibration speed and feed rate were determined using one fine ore type. Mats with different aperture sizes, and different feed moisture contents were also tested. Trials were then conducted on various fine ore types to indicate the effect of different size distributions on separating efficiencies. The effects of feed moisture content were determined with these ore types, and a blend of lump (nominally -30+6 mm) and fines was tested to compare the screen's performance with that of the bottom deck of the minesite product Screens.

Jan 1, 1991

By B Wu, C Zhao, B Lei

At present, the friction factor is calculated by measuring pressure drop and airway configurations. However, the workload of on-site measurement is heavy, and the measurement results are easily disturbed by the external environment. In order to meet the need of intelligent ventilation to quickly and accurately obtain the friction resistance of roadway. Based on the important of roughness in Atkinson friction resistance formula, in this paper, fractal theory is used to characterise the 3D rough surface, and a method based on fractal dimension to describe the roughness of roadway surface and calculate the friction resistance was proposed. A computational model of friction resistance for fractal characterisation of roadway 3D rough surface was established. The parameters of the model were deduced and verified by using Nikuradse experimental data. The fractal dimension of roadway surface was calculated by 3D laser scanning data of Kailuan roadway, the established friction resistance calculation method was compared with the field resistance measurement results. It is considered that the calculation method of friction resistance based on fractal theory is reliable and can well represent the influence of 3D rough surface characteristics of roadway. The result show that the new established friction resistance formula compared with the traditional Atkinson formula in Nikuradse experimental, the average relative error is 6.874 per cent, and compared with the measured results of ventilation resistance in Kailuan experimental roadway, the relative error is 6.667 per cent. Comprehensive evaluation and analysis suggest that the new formula can well reflect the influence of 3D rough surface on friction resistance, combined with 3D laser scanning technology, the friction resistance of roadway can be calculated quickly and accurately. This research provided a reference for the key technology and theoretical development of intelligent ventilation parameter measurement.

Oct 12, 2022

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994

By B Wentzinger

This paper presents the results of state parameter estimates in an active coal boiler ash storage facility using the most recent methods currently in use for cone penetrometer interpretation. State parameters estimates are also compared with the critical yield stress ratio approach, which is proposed as an additional liquefaction potential screening method. Recommendations are provided regarding additional in situ tests and laboratory tests that may be undertaken to improve the state parameter assessment and data produced for use in subsequent stability or liquefaction studies.

Jul 1, 2021

The Charters Towers 1:250 000 Gravity Data Set represents a new initiative of the Department of Resource Industries (DRI, formerly Queensland Department of Mines) to provide high quality regional gravity data over areas of the State that have high potential for new mineral discoveries. The Department has adopted a strategy to upgrade geophysical data to complement the ongoing Regional Geological Mapping Program (RGMP) of this Department and in areas where the data would be of most benefit to the mineral exploration industry. Part of this strategy is to ensure that these data are released within 6 months of data collection.The 1989 Charters Towers survey was completed as a joint project with the Bureau of Mineral Resources, Geology and Geophysics (BMR), and is the first regional geophysical data acquisition project undertaken by the DRI. Prior to this survey, the only gravity data in this area dates from the B MR regional surveys carried out between 1960 and 1967.

Jan 1, 1990

By K Nguyen

The advances in computerised processors and digital microscopic imaging have enabled more studies that attempt to quantify textural information from rock images. However, a texture classification system designed for geometallurgy has always been challenging, as it combines general image analysis techniques and specific texture classifications in terms of the size, shape and orientation of mineral particles. In this paper, a novel texture analysis technique using grey level radial shell association (GLRSA) and spectral angle mapper (SAM) to discriminate between different geological images is outlined. The technique can be applied in routine analysis and characterisation of mineralogical and textural attributes which may correlate with variability in mineral processing behaviours. Using this texture analysis technique, a set of small texture reference images, a texturelet reference library, has been identified from a suite of drill core images. Rock types are classified according to the proportion of each texturelet type recognised. The library is site specific.CITATION:Nguyen, K, 2013. A new texture analysis technique for geometallurgy, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By P J. Terbrugge

Many ore deposits have considerable vertical extent which is not always known at the time of commencement of mining. In many of these cases, initial mining is by opencast methods, and as ore reserves are proved to greater depths, the pits are often planned to go deeper than had been originally envisaged. In such cases, surface plants and critical underground facilities such as conveyer tunnels, access ramps, ore passes, hoisting shafts and ventilation shafts are often located much closer to the pit rim and the orebody than is desirable for the deeper mining situation. This usually raises the question of the stability of such underground excavations, which may be critical for the viable longer-term mass underground operation of the mine. In this paper the key considerations in the evaluation of the stability of the overall mining environment for ædeepened minesÆ are defined. Aspects which are dealt with are: open pit stability, shaft stability, dilution, mudrushes and airblasts, and selection of mining method. The necessary stability evaluations are put into the appropriate context by considering two case histories. Critical parameters and considerations which need to be addressed during the evaluation of excavation interaction are also discussed.

Jan 1, 2000

By J B. Holman, P A. Weber, P Lindsay

Underground and opencast coal mining has occurred since 1896 on the Stockton Plateau, West Coast, New Zealand. Acid Rock Drainage (ARD) from historic and current mine workings has had an adverse environmental impact on the surrounding aquatic environment. The two main catchments affected by ARD from historic and current mine workings are the Mangatini and St Patrick Stream catchments. Solid Energy New Zealand Ltd (SENZ) is using active (e.g. alkali dosing) and passive (e.g. engineered cover) technologies to mitigate the adverse environmental effects associated with ARD contaminated waterways. This paper discusses the passive technologies. Principal strategies include the capping of high capacity potentially acid-forming volumes of overburden. The mudstones were found to generally have the highest sulphur levels compared to other overburden lithologies. Areas with high mudstone volumes are prioritised to be encapsulated and 390 Ha is planned to be capped in the Mangatini catchment in the near future.   Monitoring beneath granite, cement kiln dust and coal combustion product covers show oxygen can be reduced to less than 10% of atmospheric levels. Laboratory column leach tests that were subjected to oxygen flux rates of 10 % showed reducing oxygen ingress into acid-forming material can result in significant acid load reductions.   The oxygen content below the cement kiln dust cover was generally lower than 5% and water quality measured in lysimeters beneath this cover improved after 50 weeks of emplacement. Column leach tests containing saturated samples were undertaken to determine the most appropriate water medium in preventing pyrite oxidation. The sample saturated with ARD (pH ~ 3) had a negligible acid production rate and leached very minor Al concentrations although Al is soluble at low pH. This indicated saturating waste rock dumps with ARD can be an effective method in mitigating ARD formation.

Jan 1, 2007