Search Documents

By Parks T. C

A low-grade disseminated nickel sulphide serpentinite ore from W.A. had a relatively high permeability after drying. Various techniques indicated that the permeability resided within a fine network of fibrous vein- lets and especially within coarse cracks along which the sulphides lay. The ore minerals were therefore open to selective extraction by chemical leaching. A IM ammonia-7.8 wt.o "ammonium carbonate" solution, oxygenated at 1 bar oxygen pressure and about 23¦C, released nickel, copper and cobalt from the sulphides, leaving a permeable residue of goethite, while calcium, magnesium and iron concentrations remained negligible in the leachant. The nickel and copper was electrodeposited directly from the pregnant liquor in a deposit which included 16.5 wt.% sulphur. Enhanced copper/ nickel ratios early in the extraction suggested that valleriite (not amenable to flotation) was leached preferentially. Th$ controlling influence of the pore structure was demonstrated by the dependence of leaching rates on the size of the ore particles used, and on the measured porosity of different ore samples. A 2mm size was probably the optimum for exposing sulphides to the leachant. Leaching was accelerated by increasing the temperature and oxygen pressure.

Jan 1, 1974

By Lilly PA, Kavetsky AP

An empirical, kinematic model is developed which calculates the trajectory of individual blocks of rock in a blast, their point of impact in the muckpile and the final shape of the muckpile. The method is based on the determination of initial block velocity and requires input on stemming length, bench height, subdrill, burden, spacing, energy of explosive per unit length of blasthole, energy attenuation rate and resistance to movement. The model, which will form part of a comprehensive blast simulation package, has application in open cut mining in predicting muckpile geometry and the movement of grade blocks during blasting, which in turn impact on shovel productivity and grade control.

Jan 1, 1986

By A Crosky, S Saydam, H Chen, H L. Ramandi

Cable bolts and rock bolts are used as primary and secondary anchoring systems in many underground mines. Reports on the premature failure of cable bolts and rock bolts due to stress corrosion cracking (SCC) in underground coalmines have been increasing in the past two decades. The previous studies found that the SCC in both rock bolts and cable bolts occur as a consequence of atomic hydrogen diffusion into the material, which is known as hydrogen-induced stress corrosion cracking, HISCC (Craig et al, 2016; Wu et al, 2018b). While research to understand the process of SCC occurrence in underground mines is still required, finding a prevention solution to protect the bolts from HISCC is crucial. In this study, we analyse a variety of commercially available coatings for steel corrosion prevention, including barrier coating (ie epoxy, polyester TGIC) and sacrificial coating (hot-dip galvanising). We test the coating on coupons manufactured from rock bolts and cable bolts used in the coal mining industry.

Nov 29, 2022

Completing its historical role the opera tion of copper blast furnace of the Saganoseki Smelter was terminated in 1970, but it left some interesting data on metal lumps formed at the furnace bottom. Analysis disclosed the lumps to be speiss containing 100 to 10,000 g/t of Au and Ag and stratified to iron speiss and copper speiss. Solidifying temperatures of iron speiss and copper speiss being approximately 1,090¦C and 800¦C respectively, copper speiss precipitated at the lower side. The distribution coefficient of Au and Ag between matte and speiss (g/t Au(Ag) in matte / g/t Au(Ag) in speiss) is in the range of 1 x 10 2 to 2 x 10 ' and 1 x 10 1 to 5 respectively. The higher Cu % is in speiss, the-more An and Ag are distributed into speiss. Except for a few data, these results comfotm well to the range of distribution equilibria of Au and Ag in matte and speiss systems by Gerlach and Others.

Jan 1, 1980

By Collins M. J, Ozberk E

A major advantage of the Sherritt Zinc Pressure Leach Process is the conversion of sulphide sulphur in zinc concentrate to elemental sulphur during pressure leaching. Elemental sulphur can be recovered as a marketable byproduct by flotation of the leach residue, and melting and filtration of the sulphur flotation concentrate. The behaviour and deportment of sulphur during pressure leaching, flotation, and melting and filtration are discussed in this paper using data obtained from the treatment of a wide variety of zinc concentrates in the laboratory miniplant at the Sherritt Research Centre. The quality of the elemental sulphur byproduct and a process for purifying the sulphur are also Presented.

Jan 1, 1993

Laboratory experiments have been used tostudy a wide range of convective processes which are significant for the formation of rocks and the ores that form in them. Metal-rich solutions flowing through the sea floor produce 'black smoker' chimneys; both the size and structure of a solid chimney and the height to which the plume of effluent rises above it can be predicted using model experiments. Analogues of processes in solidifying magmas can also be studied using crystallizing aqueous solutions. The release of lighter or denser residual fluid as crystallization proceeds, and the resulting compositional convection, have a vital influence on the differentiation of initially homogeneous magma and on the evolution of stratified magma chambers. Mixing during the replenishment of magma chambers, and its dependence on the rate of filling and on the fluid properties, have also been studied on the laboratory scale. Experiments carried out in different geometries have been applied here to the formation of platinum and chromite ores and komatiite lavas. Larger-scale mantle convection, in particular the motion of subducting plates and plumes rising from the core-mantle boundary, also determine the tectonic settings in which ore bodies form. These phenomena too can be usefully investigated in laboratory experiments using very viscous fluids.

Jan 1, 1990

By Miller RJ, Eager DT, Lama RD

For safe and efficient mining operations, it is essential that environment and equipment status be monitored. A system that gives quick access to status at any given time, and also permits quick analysis of their history, is required. Such a computer based monitoring system has been installed at West Cliff Colliery.The system is based on 2 super mini computers. Three major sub-systems monitor conditions in the longwall operations, environmental conditions in the intake and return roadways, status of the underground and surface installations, and mining and transport equipment.

Jan 1, 1985

By Beeby C. j, Fernando W. J, Ming M. Q I, Guang Li Xi

Removal of moisture in steam-fluidized, mainly steam-heated, fluidized beds makes possible significant energy savings over conventional forms of large-scale drying. The systens are described and their applications to brown coal and alumina hydrate are reviewed. In application to brown coal the use of the system to permit meeting diurnal variation in power station output, and the use of triple-effect drying to minimise coal usage and to avoid the necessity of recovering in the turbines the energy in the steam from the last dryer are discussed. To facilitate the rapid adoption of the systems proposed, studies are being made of heat-transfer to dried coal, of moisture equilibrium in pressurized and vacuum systems, of tapered beds as a means of reducing carrier steam and permitting wider size variation, and of the use of carrier solids for drying lump materials.

Jan 1, 1989

By McGuckin P. H, Logan A. S

The BHP Minerals' Cannington silver-lead-zinc deposit is located approximately 190 km south-east of Mount Isa. The deposit, is hosted by Proterozoic rocks beneath a thin cover of younger sediments, and contains a total estimated resource of 45.3 million tonnes at 11.1 per cent lead, 4.4 per cent zinc and 500 g/t silver. The deposit is separated by faulting to form a shallow, lower grade Northern Zone and a deeper, higher grade Southern Zone (Roche, 1994). Contract development of an exploration decline to test mineralisation in the Southern Zone commenced with the excavation of a boxcut in August 1993. The complex variably deformed Proterozoic sequence interpreted from drill core and intersected in the exploration decline has required a high level of practical rock mechanics input to achieve: ò appropriate support designs, ò a high quality of installation, and ò required development advance schedules. The Norwegian Tunnelling Index (Q System) in conjunction with regular face mapping is used as an operating tool to assist in decision making for ground support. Line mapping, discontinuity analysis and wedge assessments are conducted routinely to optimise ground support requirements in the decline, intersections and all other underground excavations. Throughout the project, an emphasis has been placed on developing a strong working relationship with the contractor to achieve quality assurance program targets.

Jan 1, 1995

For the past 40 years, underground trucking using diesel powered or electric wheel driven vehicles, either conversions of surface trucks, or purpose built, has been the preferred means of ore and waste transport in underground mining. The relatively low capital cost, flexibility and requirement for minimal infrastructure means that trucking systems are selected in the early stages of a mining operation. An increase in the carrying capacity of trucking systems with dimensions to operate within existing development excavations is the solution to long term ore and waste underground haulage systems using trucks. The next generation of underground trucks will be low profile articulated trucks with carrying capacities up to 60 t.

Jan 1, 1998

By N Mangadoddy, P Jampana, S Diddi

The study of air-core dynamics in hydrocyclone operation is essential for predicting separation efficiency in mineral processing. Electrical resistance tomography (ERT) allows non-invasive measurements of hydrocyclone internal flow dynamics. Existing regularisation methods such as Gauss-Newton and TV norms rely on optimisation techniques which have very high computational cost for very fine meshes. In contrast, the monotonicity method has much lower computational cost as it does not solve such minimisation problems. In this paper, results from the monotonicity method, Gauss-Newton (GN) (Tikhonov) and Total-Variation (TV) norm-based minimisation methods for estimating the air-core diameter in hydrocyclones are compared. We study these methods on the laboratory hydrocyclone experimental two-phase flow data. The results obtained are validated against High-speed video (HSV) imaging and Computational Fluid Dynamics (CFD) results. The results on different mesh sizes, in particular for very fine meshes with the number of cells ranging from 30 000 to above 100 000 are also investigated. The data used in this study is obtained from ITS Z8000 ERT system. This system does not measure the voltages on the current carrying electrodes. Since these voltage values are required for the monotonicity method, we implement an interpolation method to compute them. The results show that the monotonicity method provides a closer approximation of the interface between air and the water phases.

Aug 24, 2022

Western Mining Corporation began shaft sinking operations at it's Foster orebody, south of Kambalda, on the 20th June, 1984. The top levels of the orebody are currently being mined via a decline some 1.5km away.Long term plans require the shaft and decline to combine and produce 400,000 tonnes of nickel ore per annum. Eventually all of the ore produced will be hauled up the shaft.The shaft is 4.5m in diameter and the target depth is 760m. Ground conditions to date suggest there will be no further need for concrete lining beyond the oxidised zone. As such, the sink is an open-shaft development in competent basalt rock. Shaft furniture will be installed on completion of the excavation to the target depth.This paper summarises the experience in the project to date, along with comparisons to conventional shaft sinking methods employed in previous years at Kambalda Nickel Operations.

Jan 1, 1985

By D Craw

A glasshouse experiment was set up to investigate arsenic uptake in rye corn grown in different arsenic rich substrates. Sods of material were taken from various locations and planted with rye corn seeds. The plants grew for 13 weeks after which time the above ground biomass was harvested. Analysis of the rye corn plants showed a narrow range of arsenic concentrations, which did not reflect the arsenic contents of the soil. Comparison of the results from this study with previous work showed the glasshouse rye corn to have lower arsenic concentrations in above ground biomass than rye corn grown in field conditions. The environmental conditions present on the tailings and water-rock interactions were considered the main factors involved with the difference in arsenic uptake between field studies and the glasshouse study. This suggests that bioavailability processes are influenced by a variety of factors and cannot necessarily be predicted by the use of soil factors or glasshouse trials alone as is often done when planning phytoremediation work and mine shut down.

Jan 1, 2007

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By Hutchings SG, Skimmings T

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

By K H. Esbensen

Sampling of grain, animal feeds (solid and liquid) including important mineral mixtures in the Danish agricultural sector is subject to an ongoing investigation with the objective of improving existing (suboptimal) sampling procedures. Results from the first six months are presented here; the project will continue for two more years and will include international collaborators (Australia and Canada). The Danish authorities have instituted a system of control analysis, which contains a set of mandated sampling and analysis methods. From a preliminary survey it was concluded that in fact all of the existing sampling procedures are not optimised in the light of Pierre GyÆs Theory of Sampling (TOS).

Jan 1, 2005

Magnesium-rich olivine is used as an additive in LKABÆs iron ore pellets in order to improve the high-temperature properties of the finished products. Olivine is only added to the pellets that are manufactured for ironmaking in the blast furnace process. The olivine comes from Minelco/LKABÆs mine at Seqi in Greenland. This dunite complex of Archean age contains about 95 - 98 per cent olivine. The grain size is typically 1 - 3 mm but much larger euhedral olivine crystals are common in the porphyritic type. The serpentinisation is absent or weak. The most common minor minerals are chromite, chlorite, talc, phlogopite, amphibole and pyroxene. The crushed olivine is transported to LKABÆs pelletising plants in Northern Sweden. After grinding, small amounts of olivine are mixed with the magnetite concentrate. The concentrate is rolled into green balls, about 10 - 14 mm in diameter. The moist green balls are transferred into the pelletising machine where the maximum temperature is about 1250¦C. The residence time in the pelletising machine is about one hour. Olivine is used in order to get pellets with better high-temperature properties. This paper deals with the olivine alteration during the pelletising process and the behaviour of magnesium following the decomposition of magnetite. The reactions are quite complex in the pellets because the physico-chemical conditions vary considerably in the process from one process step to another, and in the pellet bed from the top to the bottom. Some olivine particles in the finished product show very slight alteration, some particles are completely decomposed. The formation of the iron-rich coronas around the olivine particles is the most typical alteration. In the finished pellets the magnesium is mainly distributed between the following phases: unaltered olivine, coronas, Mg/Fe-ferrite and silicate slag.

Jan 1, 2008

By Cliff D, Harrison P. Hester C

During 1997 two different types of coal mine inertisation equipment were trialed in separate underground coal mines in Queensland.In April 1997 tests of the Polish developed GAG-3A inert gas generator were carried out at the Collinsville No 2 Coal Mine. These demonstrations indicated that the GAG-3A device was applicable in underground coal mines and that with respect to inertisation rate the device outperformed all other currently available techniques. The unit was assembled rapidly and operated safely during surface and underground trials and no mechanical problems were encountered with the device. The GAG-3A is not suitable for every fire scenario particularly if large volumes of fresh air are being drawn into the mine(where multiple units may be required), but with respect to the selection criteria developed by the Moura Implementation Process Task Group 5 criteria, the unit performed up to the specifications required.

Jan 1, 1998

By G MacDonald, B Forsyth, D Corkery, T

An investigation was carried out at Diavik Diamond Mines Inc (DDMI) to identify and quantify the mechanisms through which ammonium nitrate (AN) was entering the mine discharge water. The goal was to develop and complete an investigation of the potential AN loss mechanisms in order to assess their contribution to ammonia in the mine water system. The initial phase of the project involved the collection and analysis of blasting and water quality data that were used to determine the mechanisms by which the ammonia enters the mine water system and to establish a baseline data set for comparison with results from future trials designed to reduce AN loss. Three potential options for reducing AN loss were identified through the first phase of the project. The second phase of the project involved conducting a series of monitored trials with changes made to the drilling and blasting process. The results of these trials were compared to the baseline data set to determine if the changes introduced for the trials had reduced AN losses while producing satisfactory blast results. This paper describes the process for the collection of the baseline data, provides an analysis of the resulting data, discusses the changes made to blasting operations in order to minimise AN loss and describes the results observed subsequent to these changes.

Jan 1, 2007

By P Ritchie, E H. Briese, N A. Currey

Kidston Gold Mines, located in semi-arid North Queensland, Australia is currently in its closure phase. Highly innovative and comprehensive rehabilitation strategies were employed at the site, including the direct revegetation of the surface of the tailings storage; the construction of a tailings sediment entrapment pond; the construction of a spillway to drain large rainfall events from the surface of the tailings; the construction of store/release covers over the tops of the waste rock dumps; the sheeting with oxide waste rock of the waste rock dump slopes; the partial back-filling of the initial Wises Hill Pit with waste rock and thickened tailings produced from the subsequent Eldridge Pit; the partial flooding of Eldridge Pit following the end of mining; and the construction of wetland systems to treat contaminated tailings and waste rock dump seepage. These closure strategies involved the careful consideration of water management. Specific water management issues included understanding the water balance of the tailings dam; the operation of the tailings dam sediment entrapment pond and spillway; understanding the water balance of the store/release waste rock dump covers; the importance and sustainability of vegetation on the tailings, store/release waste rock dump covers, and on the sheeted waste rock dump slopes; the level and quality of water in the partially flooded Eldridge Pit; and the treatment of contaminated seepage in the constructed wetlands. The seasonal and highly variable rainfall experienced in this semi-arid climate posed a number of challenges for the management of water on the site post-closure. The paper details these challenges and highlights how they were resolved over the period leading up to and following the end of mining.

Jan 1, 2003