Search Documents

By E S. Bernard

Toughness testing of fibre reinforced concrete (FRC) at 28 days age is typically undertaken as part of quality control for the many applications where fibres are used in concrete, including shotcrete, tunnel segments, and cast-in-place tunnel linings. The performance achieved at 28 days is usually assumed to be retained with increasing age. However, as the average strength grade of concrete used in most tunnelling applications, including tunnel segments, has steadily increased over the last 20 years, this assumption is becoming increasingly unviable. This is because for some types of fibre the mode of post-crack fibre behaviour depends on the strength of the concrete and can change from a desirable high-energy pull-out mode to a low-energy rupture mode as the strength and age of concrete increases. This paper describes a series of trials performed over two years in which the American Society for Testing and Materials (ASTM) C1609/C1609M beam tests were used to assess the performance of FRC reinforced with two widely used brands of steel and macro-synthetic fibre. The hooked-end steel fibres used for half the beams exhibited a dramatic fall in performance beyond 56 days age as the mode of failure changed from pull-out to rupture. The other fibre did not exhibit a fall in performance with age. This phenomenon highlights the need to quantify performance of FRC at much later ages when long-term performance is required, for example, to resist seismic events or changes in ground stress due to nearby excavations. As an alternative, a reduction factor may be applied to the performance of FRC mixes for which evidence of satisfactory long-term performance is not?available.CITATION:Bernard, E S, 2014. Age-dependent changes in post-cracking performance of fibre-reinforced concrete for tunnel?segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 229–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Crosby N. R

The design of mine openings and the assessment of their reserve are processes ihicl, require the routine manipulation of considerable amounts of data. A number of computer programs have been assembled to operate in a mini computer in order to provide some mechanical assistance for these processes. The system responds to plain language commands. which allows mining engineers to compute the reserves for a number of possible mining outlines, on an interactive basis. Methods of numerical analysis were used in preference to statistical or qeostatistical techniques.

Jan 1, 1977

By Pilkington T, Noy A

The Yallourn North Extension (YNX) open cut mine ceased mining operations in early 1989. YNX may be used again for coal supply at the discretion of the Coal Corporation Of Victoria (CCV); this has resulted in the need for interim rehabilitation of the site which may last many years, or indeed, permanently.The site has suffered substantial surface erosion over the years with large areas of bare clay and coal batters remaining exposed. The first priority is to reduce the quantity and improve the quality of stormwater runoff from the site. This is best achieved by appropriate revegetation and the use of existing landform depressions as silt trap/wetland areas. Proposed rehabilitation needed to take into account the sensitive fire safety of the open cut and the option to re-open the mine if CCV deems appropriate.The authors detail the factors involved in the rehabilitation proposal and the multi-disciplinary approach to planning including engineers, scientists, a forester, landscape architects and community input. The rehabilitation design included early consideration of land use and ongoing maintenance issues linked to water quality improvement factors including vegetation. Engineering input was required for reshaping and clay covering exposed coal batters and the design of silt traps which will revert to wetlands in future. The integration of each discipline has produced a rehabilitation design pleasing to both the SECV and community alike.

Jan 1, 1992

By Walshe JL, Solomon M

The Emperor vein system lies on the eastern margin of the Tavua volcanic structure. This is of Miocene age and occurs in basalts(the Mba Volcanics) probably underlain at about 2 km by calcite-rich sediments (the Vatukoro Formation). The lodes are generally flatmakes, or steep fault fillings, or complex shatter zones, and consist of quartz and altered wall rock. In areas of open cavities it is possible to establish a paragenesis which involves five quartz stages and two ore mineral stages. The first ore stage contains calaverite, krennerite, sylvanite and native tellurium, the second petzite, hessite and native gold. The quartz stages are thought to have formed slowly (102 years) from boiling solutions of low salinity at temperatures varying with time from about 250¦C to 190¦C. The system was sealed, the temperature gradient near vertical and the mass flux small. The ore mineral stages probably formed relatively rapidly (101years) from boiling solutions at 250¦ to 200¦C when the system was mainly open. Gold deposition was probably largely a result of fall in aH2S due to boiling, the calculated solution concentration falling from a maximum of about 8 ppb at 250¦C to about 8.10-3ppb at 200¦C. Boiling is also probably responsible for an increase in a02 (by loss of H2) and fall in aTe2 (by loss of H2Te). The fluids are thought to have had a large component of meteoric water and to have been heated by plutons in the core of the volcanic structure. Stable isotope data indicate that they derived their carbon from the underlying Vatukoro Formation and their sulphur from sediments. Circulation may have been confined to the outside of the volcanic structure because of the relatively low permeability of the flows, pyroclastics and dykes within it.

Jan 1, 1987

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993

By Osborn G

The bulk flotation behaviour of an industrial rougher bank has been determined with a view to characterising the size iepend ent behaviour of the identifiable nineral groups present. A relatively simple flotation model, based on first order kinetics and the assumption of perfect mixers in series ias been used to provide a fit to the operation of the cells. The adequacy of the model is discussed in relation to the characteristics of the ore and the size iependancy of the parameters. It is shown that improved fits are possible if the model accounts explicitly for this size dependancy and demonstrated how the model may be of use in prediction of the grade recovery relationships for different operating conditions as an aid to plant optimisation.

Jan 1, 1986

Total extraction is a misnomer and invariably some coal losses occur in the mining of pillars. "Fulls" pillar extraction is by the pocket and fender method, the splitting method or the open end method, with extraction in the pillar, and in rows of pillars in planned sequence, using combinations of coal and timber and roof-bolts for support. Where circumstances dictate, partial extraction is used, leaving behind portions of pillars in large blocks for support. The use of such extraction plans and supports as minimum guidelines has contributed greatly to safety in United States Coal Mines.

Jan 1, 1974

By M Battersby, F Parra, S Sanchez-Pino

Pneumatic flotation, as developed by Dr Rainer Imhof, has been applied in commercial beneficiation operations since 1987. Over 85 flotation cells have been installed in more than 30 operations, successfully beneficiating a wide range of minerals. Pneumatic flotation is however still considered as a non-conventional flotation process. Due to its highly selective nature in operation it has generally found its market in difficult applications where conventional flotation equipment has struggled. Compa±fa Minera Huasco (CMH) operates an iron ore pellet plant in central Chile. CMH desired to produce a low silica pellet for the export market where the SiO2 grade should not exceed 1.5 per cent. It is common practice in other countries to float quartz from hematite with relative ease. However, the silicates contained in the magnetite ore of CMH are only present as quartz in small quantities and the major undesirable silicates are difficult to float. CMH spent considerable time on developing a reverse flotation process and a reagent suite to try and reduce the silica content to acceptable levels. However, extensive laboratory and pilot plant tests with conventional mechanical tank type cells and with column cells failed to produce the required reduction in impurities. A series of tests with pneumatic flotation cells indicated that this type of flotation technology could achieve the required silica target. A 500 tph Imhoflot pneumatic flotation plant was subsequently constructed and successfully commissioned by CMH, making it one of the largest iron ore flotation plants in the world. This paper details the background and testing that was undertaken by CMH which led them to choose pneumatic flotation as the preferred process and compares the test results with that achieved in the industrial plant.

Jan 1, 2005

The standard charge weight scaling laws imply that only one particular delay (that possessing the maximum instantaneous charge) contributes to the ppv. However, the present analysis clearly demonstrates that a varying number of blastholes contributes to the ppv. This number also increases with distance, x, between the blast source and the detector, and is caused by waveform broadening due to attenuation. Thus the operative charge weight, itself, is also a function of the distance, and so makes the standard charge weight laws difficult to implement. If the delay time scatter is neglected, then, under certain conditions, relatively simple expressions can be derived for the ppv magnification, FN, as a function of the number, N, of blastholes. When the influence of delay scatter and random fluctuations in each blasthole vibration is included using Monte Carlo simulations, then, to a first approximation, the condition FN=KNx applies, where KN is a constant dependent upon N. Unfortunately, however, for any particular blast this condition cannot be distinguished from the standard charge weight scaling law. The dependence of ppv on N would only be apparent if blasts of differing N were to be compared in an otherwise identical environment. Since this situation is very difficult (if not impossible) to realise, then the influence due to N, although significant, goes largely undetected. Another problem associated with standard charge weight scaling laws is the difficulty of accurately assessing the appropriate charge weight, even if attenuation broadening is neglected. For example, if a number of blastholes are very close, then they experience a vibration interaction which is non-linear. However, if the same blastholes were to be widely spaced, then the separate vibration signatures add linearly. The standard charge weight scaling law fails to distinguish between such linear and non-linear regimes. Unfortunately, in many production blasts, both regimes exist throughout various portions of the blast spatial pattern and so makes it difficult to determine the operative charge weight. The solution to the combined influence of waveform broadening and linear/non-linear interactions will obviously require substantial future research. A possible solution may be found in the use of numerical dynamic codes.

Jan 1, 1990

We operate a 50 cubic metre per hour mobile alluvial tin mine on small scattered deposits in the Irvinebank area. Wash is loaded by a Cat. 950 front end loader into the bin of a screening section and screen undersize is pumped to a separate jig unit. Both units are rubber tyre mounted and are shifted once a month when the haul distance gets to about 150 metres. The shift takes about 8 hours.The screening section is sited close to the face with a ramp for dumping in and a one metre drop for the screen oversize which is removed by the loader.A reciprocating plate feeder with variable rate hydraulic drive, feeds wash onto a horizontal 1.2 metre x 2.2 metre two deck Kinergy screen. Minus 10 millimetre undersize is pumped by a Warman 6/4 sand pump with a 37 kW variable speed Reeves Motordrive to the jig unit.The jigs are placed 20 to 70 metres away so that tailings will run back into previously mined ground. Reject stone is used to impound the sand and mud, allowing the water to filter through and return to the feed water pump.An MTE trapezoidal module is used as a primary jig. Hutch product is pumped to an eight cell clean-up jig which we developed ourselves along MTE lines. It has a trapezoidal shape and sawtooth stroke provided by cams. Clean tin is taken from the first four spigots. These consist of clear plastic tubes fitted with taps so that there is no water loss except when the tin is drawn off. Fine concentrate from the last four spigots is put over a curvilinear table which sits on a steel base packed with earth.

Jan 1, 1986

Computers and other microprocessor technology lead the world of technological change. Nevertheless, the real advances in the world at large are not necessarily in the computer industry, but in the industries whose economics benefit most by the advances that this computer revolution makes possible. The minerals industry has always been in the forefront of this advance. Technological change in the era preceding the industrial revolution, and the mining industry's part in it, provides an instructive lesson for what is happening today. Strong parallels can be drawn for predicting future advances. With each technological advance allowing more efficient production comes a re-alignment of economics - absolute and relative changes to prices, to quantities demanded, and to other market characteristics. This re-alignment applies not only to the mineral industry, but also to the world at large. Adaptability, rather than technical advancement per se is the key to survival and growth in a changing world. 'Adaptability' as a concept is easy to support. As an operational philosophy it is not so easy to implement. As a goal for planning, it is much harder to quantify. A fixed scenario of a future world may provide helpful guidelines, but a scenario that demands adaptability to an uncertain future world is much less definite. Of course, everyone else in the world is also uncertain about the future, and they are making their plans using different assumptions. This virtually guarantees that our future will turn out different to our expectations. This is in part what Hayek (1945) calls the 'knowledge' problem. Until now, most of the planning and technical research undertaken in the world has ignored this problem. This ignorance is a luxury that we can no longer afford. The paper looks at the history of technological change and highlights the characteristics of successful technological revolutions. 'Adaptability' to unforeseen circumstances is the key to success in this environment. The paper examines the knowledge problem from the perspective of the mineral industry, and suggests a number of directions for maximising the returns from application of computer technology in this important area.

Jan 1, 1995

By Koppe J. C

This study presents the procedure of mine modelling and reserve evaluation by means of statistics, computer interpolation methods and aerophotography interpretation. All data are from Carbonifera Treviso, Laura Muller City, Santa Catarina State, southernmost Brazil. From 22 bore holes and nine trenches opened in the coal seam outcrops, a data base including level references and thickness of all rock formations was created.Using this information, basic statistic analysis was carried out, showing that there are three different populations (three modal distribution). These populations defined three geological blocks with different characteristics of overburden removal and mining methodology. This mathematical approach for analysing geological data is very important for correct mine planning and complementary prospection.

Jan 1, 1993

By Van Barnefield J G

This paper is based on an evaluation project engaged upon jointly by Mount Isa Mines Limited nnd" IBM Austra]ia Limited. Mount Isa Mines Limited produces most of its copper from large underground open stopes within massive orebodies. Variations in the position and shapes of these stopes can result in improved metal recovery. An interactive graphics system has been developed to assist the mine design engineer optimise his design. The system can assist the engineer throughout the orebody visualis- ation, initial design and optimisation phases of his design. At any stage the engineer may call upon the display of gridded mesh data, digitized ore outlines or existing stopes or development (drives, cross-cuts). This information may be viewed in plan or any vertical section or in three dimensions with rotation. Tonnage and grade calculations may be quickly performed for initial stope outlines or for modifications to them during the optimisation phase. The system design is highly modular. An array of functions for the manipulation of coordinate and line information may be linked with the development or stope design functions in whichever way the designer desires.

Jan 1, 1977

By Bhattacherjee A, Makesh S

Mechanised sub-level stoping is one of the most widely accepted stoping practices followed in base metal mines in India. As a general practice, blast-scheduling of rings in these stopes is done either heuristically or randomly which leads to a high fluctuation in ore grade when drawn and delivered to the mill. In this paper, dynamic programming has been investigated as an optimisation technique for optimal blast-scheduling of rings. A microcomputer based dynamic programming algorithm has been developed in C language which runs under the UNIX environment. A case study based on Indian mine data is presented to demonstrate the application of the dynamic programming concept and use of the developed software. It is concluded that dynamic programming can be used as a production planning tool in Indian mines practicing sub-level stoping and following heuristic/random approaches for blast-scheduling of rings.

Jan 1, 1995

This paper concerns a pragmatic approach to a problem that is common to many operations in the mining industry: how, over the short-term, to grasp the extent and distribution of long-term financial risk from environmental causes and reduce these risks strategically, in order to maintain stability and flexibility in the operations. Surprisingly, many companies operate without an environmental master plan or tools that can help managers measure and reduce financial risks. Such companies may be subject to unknown unacceptable financial risks from environmental causes. While many companies have some kind of internal system of environmental standards, it is often the case that such systems have uneven or limited effect, and offer no opportunities for visualising, measuring or managing aggregate financial risks from environmental causes. `Aggregate risks' are defined here as the calculated total expected financial costs to a company, or a subdivision of a company, from environmental causes at nominated operations over a defined time period. Aggregate risks take into account the type and magnitude of an environmental problem set, the likelihood of occurrence, and the time frame during which the problems will develop or solutions are required. For the large corporation, the 'amount of' aggregate environmental risk is a statistic that can be managed, along with other financial parameters, at the corporate level to improve the stability and predictability of operations, and protect the interests of shareholders. This paper concerns development of a management framework and a tool for the large corporation that responds to the need for managing aggregate environmental financial risks. The logical framework proposed to overcome the need for strategic vision is the Environmental Master Plan, and this is described in the next section. The analytical tool proposed to measure aggregate risks and provide relevant data and insights to managers, is called an Environmental Risk Management Information System, and its mechanics are described in a subsequent section.

Jan 1, 1994

A contract for three 20 ft diameter vertically mounted axial flow fans of the same aerodynamic design, was placed by Mount ]sa Mines Limited in 1963. The hydraulic blade pitch changing mechanism, the method of blade fabrication, and the roll out centre casings are features of these fans. Protection devices and fan control are designed for unattended operation and remote control. The erection and commissioning of the fans during 1964-65 is described.

Jan 1, 1967

By Morris B. J

Soil air samples taken from the top one metre of the soil profile, were measured for C02 and 02 using portable field analysers at a number of sites of known sulphide mineralisation in South Australia. Carbon dioxide anomalies were detected over actively oxidising sulphides during autumn and winter following recent rainfall. Anomalies were not detected where no oxidation was occurring, where seasonal conditions had been very dry, or where the sulphur content of the ore was low (

Jan 1, 1993

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By Toguri JM

A solid electrolyte technique has been used to measure the activity of cobalt in liquid cobalt-gold alloys containing between 0.085 and 0.50 mole fraction of cobalt, and for temperatures from just above the liquidus to around 1550 K. The system exhibits positive deviation from ideality, both in the activities of cobalt and gold, and in the enthalpy and excess entropy of mixing. The results agree with previous measurements using a Knudsen cell - mass spectrometer technique, but differ from those reported for a gas equilibration method. The data have been used to calculate the activity coefficient of cobalt oxide in silica saturated iron silicate slags and to express the solubility of cobalt in such slags as a function of cobalt activity and oxygen pressure.

Jan 1, 1984

By Parsons A. E

The application of known pelletizing tech- nology was successful in the agglomeration of zinc concentrate into pellets of minus 6mm siz- ing using fine zinc calcine and sulphuric acid as binder. Subsequent roasting trials conducted in a 0.3 m diameter fluid bed reactor, showed that the pellets satisfactorily withstood hot physical abrasion during fluidization. Fines generation was low and the pellet calcine was hard, possessing excellent handling properties. Results of laboratory scale static pellet sinter- ing tests showed conclusively that the deterior- ation in sinter physical quality experienced with fine calcine was not apparent when the calcine was added to the mix in pellet form. Based on the results of small scale exper- imental work, a one tonne per hour pilot plant was constructed and operated. Several thousand tonne of pellets were produced-for fluid bed roasting in Badische Analin and Soda Fabrik (B.A.S.F.) turbulent layer (T.L.) roasters previously designed for roasting iron pyrite concentrate. Continuity of the T.L. fluid bed roasting operations was achieved when the waste heat boilers were replaced with atmospheric coolers and thus eliminated the problems of gas flow restrictions. Sinter plant trials were conducted over a period of two weeks with the addition of pellet calcine to the sinter feed. Results showed a marked improvement in sinter plant performance, and as a result of better bed permeability, increased sinter production was achieved, with- out significant deterioration in sinter quality.

Jan 1, 1974