Search Documents

The King River Power Development on the West Coast of Tasmania has involved the storage of the waters of the King River in the new Lake Burbury and their diversion through a 7 km tunnel to a 144 MW power station. The last kilometre of this tunnel descends through 160 m under a ridge before emerging from the bank of the King River at the power station site. The decreasing cover over the tunnel as it approaches the power station meant that a steel lining was required in the last few hundred metres of the tunnel. This paper describes the geotechnical investigations which were carried out to establish the necessary length of the steel lining.

Jan 1, 1993

By W A. Ducker, R-H Yoon, M Mao

Froth flotation relies on an attractive force between a particle and a bubble to selectively extract particles from a mixture. The range and magnitude of this attractive force is an area of ongoing investigation. We describe measurements of the effect of dissolved gases on the long-range attractive surface forces between a silica plate and a glass sphere in aqueous octadecyltrimethylammonium chloride (C18TACl) solutions. The measurements follow on the work of Sakamoto et al (2002) who have concluded that long-range interactions occur in air-equilibrated surfactant solutions but not in degassed solutions. In the present work, we have measured attractive forces that have a much larger in magnitude than the expected van der Waals force in solutions that were degassed by the same procedure used by Sakamoto et al (2002). We find that the forces are most attractive at 5 + 10-6 M C18TACl, which is close to the charge compensation point (ccp) of the glass sphere. At this concentration, the attractive force decays exponentially with distance and the decay length is 34 in air-saturated solution, and 38 nm in degassed solutions. In both air-equilibrated and degassed solution, the force is quite sensitive to the concentration of surfactant. The force is also sensitive to the pH. We note that our degassing procedure increases the pH of the solution from about 5.7 to 6.6 (presumably by removal of dissolved CO2). We find that the forces measured in degassed solution can be reproduced by using a solution that was equilibrated in air, then the pH was increased by addition of NaOH. Therefore, we conclude that the main effect of degassing in our experiments is to raise the pH. We show that the range and magnitude of the attractive force decreases in the presence of salt (NaCl). This suggests an electrostatic mechanism for the attraction. Possible mechanisms for the attractive force are examined, including the mechanisms that rely on a patchy coverage of surfactant on the silica surface.

Jan 1, 2005

By DJ McKEE

Process control emerged in the mid-1960s as a new and exciting method of improving the performance of mineral processing operations. The early Australian developments, principally in Broken Hill and Mount Isa, were based on pioneering work in instrumentation, the availability of small digital computers and a particularly effective partnership between companies with technological foresight and University and CSIRO research groups. Initial progress was rapid and within ten years many plants were committed to process control. Process monitoring is now routine and most circuits have some level of control. However, few plants have comprehensive optimising control systems as the difficulty of developing control strategies which can cope with the wide variety of conditions encountered in most mineral plants has been fully appreciated. This paper summarises past experience and assesses the degree of application of different forms of process control in metallurgical plants. Barriers to the effective utilisation of opt rising control are identified and some suggestions for advancing the application of control are made.

Jan 1, 1992

By Shoobridge PH, Firkin GR

The Imperial Smelting Process blast furnace (ISF) of the Sulphide Corporation Pty Limited zinc/lead smelter at Cockle Creek, New South wales, has in recent years greatly increased its consumption of low grade feed materials, and as a consequence has experienced periods of unstable furnace operation. Routine examination of production sinter, including softening characteristics and micro- examination, showed that the problems had been caused by an increasing silica content in sinter. The silica entered a low melting point glass phase containing calcium and lead oxides. The relative volume of this phase increased until it formed a continuous matrix in the sinter structure and this made the sinter more likely to soften at lower temperatures. Premature softening caused loss of operating stability in both the shaft and hearth of the ISr. The required sinter structure for ISF smelting was found to consist of a network of intermeshing, refractory crystals which provided skeletal strength for sinter lumps even after the glass phases had begun to soften and melt. With an understanding of the importance of microstructure and softening temperature of zinc/lead sinter and the progressive identification of those factors in sinter production which affect the microstructure, a significant improvement in stability of operations has been possible.

Jan 1, 1980

How often does one hear that a recent feasibility study was not a success? Alternatively, when scope of the feasibility study was sent out to tender there was a large discrepancy in tendered prices. If the tendered prices were to be compared to the consumer market, for instance the purchase of a car, where the concept is transport in a controlled and safe manner, prices vary by large factors, but then so do the specifications. In the case of a feasibility study, prices should be within a tighter margin as the tenderers are all quoting against the same concept and specification. Why do these discrepancies occur? Price discrepancies will in every likelihood be attributed to two main factors; one, the perceived amount of work and two, the ability of the bidder to carry the risk associated with the feasibility study. It is, therefore, important that the scoping of the feasibility study covers the detailed requirements as clearly as possible stating what level of accuracy is required. The feasibility study is one of the first activities in the life of a project. The study, like the project it is investigating, is subject to the constraints of time, cost and quality. Its primary objectives are to demonstrate the viability of a project within the outlined scope and constraints.

Jan 1, 1998

By N Winkelmann

Underground coal heating is a significant hazard in some coal mines. The broad principles of how underground coal heatings occur is reasonably known, however the technique for locating the heatings in often inaccessible goaf has been proved to be difficult. Since 2002, CSIRO, with the support of the Australian Coal Association Research Program (ACARP) has been undertaking investigations to apply and develop innovative surface-based radon technique for locating the underground heatings in Australia. This paper presents the progress of the investigation.

Jan 1, 2005

By Erickson M. E, Smith C. K, Carswell J. T

Thirteen holes totalling 3200m were surveyed using a downhole time domain Geonics EM37 system at the 830 metre level within the CSA Mine, Cobar, New South Wales, in order to search for blind, electrically conductive sulphides at some distance from exploration drillholes. A significant off-hole conductor was detected in only one drillhole.Geophysical modelling and interpretation of the survey results indicated that this off-hole conductor was caused by a sulphide lens 30 metres from the drillhole at a hole depth of 220 metres.

Jan 1, 1990

By R Rodriguez, S Gumo

The Lihir Gold Mine, in Papua New Guinea, is a large open pit operation within an active geothermal system inside a collapsed volcanic crater. This unique setting has a big impact on the mine operation because of the occurrence of geothermal hazards. The system for managing geothermal hazards that has been developed by Lihir Gold Mine is a pioneering effort that can be applied to future mine discoveries in a similar environment. The controls are integral to the mining operations and allow mining to proceed whereas without them mining could not be considered. Truck and shovel productivities in conventional open pit operations are constrained by diggability, equipment availabilities and utilisation. At Lihir, additional constraints are in the form of 100 m exclusion zones around working shovels and 50 m exclusion zones around working drills. Given that the mine has seven large digging units and six drills, this amounts to a lot of area that excludes the presence of people on the ground. So how are the necessary work like grade control, survey, blasthole loading, and in-pit maintenance performed safely to achieve production targets? The answer is in the highly specialised procedures that have been developed that utilise geological, geothermal and geotechnical knowledge to predict problem areas and also deal with the organisation of movement in the pit for people and mining equipment. This paper will detail how scheduled material movement can be maintained despite the challenging conditions faced at Lihir Gold Mine.

Jan 1, 2007

By K Esmaeili, S Aziznejad

Impact-induced rock fragmentation is a mechanism that is commonly used for rock breakage in drilling and crushing. Additionally, rock fragmentation by blasting is frequently used in rock excavation operations. Experience shows that the presence of discontinuities can significantly influence the impact-induced damage and fragmentation of rock. Quantification of the response of jointed rock masses to impact loads is complicated by the fact that the available laboratory tests are mainly designed for aggregates or intact rocks. It can be argued that neither of these tests adequately represent a jointed rock mass. This paper presents the results of a series of numerical simulations used to investigate the influence of pre-existing discontinuities on the impact-induced fragmentation of rock masses. The methodology includes determination of the static and dynamic mechanical properties of a rock unit by conducting a series of laboratory tests on intact rock samples collected from a quarry in Canada. A 2D distinct element code, Particle Flow Code, was used to generate a bonded particle model in order to simulate both static mechanical properties (uniaxial compressive strength, elastic modulus, Poisson’s ratio and indirect tensile strength) and dynamic mechanical property (drop weight tensile strength) of the intact rock. The calibrated numerical model was then used to construct large-scale synthetic rock mass samples by incorporating discontinuity networks of different intensity into the bonded particle model. Finally, the impact-induced fragmentation inflicted by a rigid projectile particle on the jointed rock mass samples, simulated by a synthetic rock mass model, was determined. More fragmentation was observed for the rock mass samples with higher joint intensity.CITATION:Aziznejad, S and Esmaeili, K, 2015. Effects of joint intensity on rock fragmentation by impact, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Digital computers, by virtue of their capacity for high speed repetitive calculation at low cost, are finding increasing application to routine calcula- tions in the mining industry. In this paper techniques are shown whereby the use of computers can be extended to more complex tasks. The regular calculation of grades and tonnages of material to be extracted from specified areas of an operating open pit is a necessary part of production planning. In this paper it is shown how these calculations can be carried out by computer. thereby freeing planning staff from manual calculation. An operating open-pit mine can be described in terms of drill logs, geological ore boundaries and pit perimeters at various levels. These form the data base which must be suitable for frequent updating to incorporate new information. A suite of computer programmes is described which operates on this data base to calculate tonnages and grades of ore within extensions to the perimeters as indicated to the system by planning staff. Possible future extensions are discussed.

Jan 1, 1971

By M Fylak, R Wenda

Advanced preparation techniques open new ways for SEM and X-ray diffraction (XRD) investigations on hydrating cementitious systems. In this paper the early time hydration of Portland cement is studied with advanced cryo scanning electron microscopy techniques in combination with in situ X-ray diffraction and heat-flow calorimetry. The application of preparation techniques and analytical methods to Portland cement hydration are presented and discussed. Some aspects of hydration reactions are focused. The reaction products of the first minutes, changes in ettringite morphology, AFm formation during the deceleration period and the visualisation of C-S-H microstructures were special points of interest. X-ray diffraction analyses and Cryo-SEM images gave essential information about phase development, reaction kinetics, microstructure and morphology of hydration products. Portlandite, AFt and AFm phases were detected by in situ XRD. Cryo-SEM analyses enabled high resolution imaging and EDX-analyses of cement particles and reaction products. The results of the different analytical methods were compared to obtain detailed information about crystallisation processes and microstructural development during the first three days of Portland cement hydration.

Jan 1, 2008

By Blain CF

For all mineral resource-based companies, it is important to reach the right balance of investment between acquisition and exploration to allow the best chance of achieving long-term corporate goals. The Broken Hill Proprietary Company Limited (BHP) provides an excellent example of success from generative exploration and supports the belief that exploration can be justified, not only in terms of investment criteria, but also because it is essential to a company wishing to build a dynamic profitable growth path based on world-class deposits as cheaply as possible. BHP was incorporated in 1885 to mine a lead/zinc/silver discovery at Broken Hill. The Company has since gone through a steel development phase (1911-1965) and is now in a major phase of growth partly based on exploration success. This third phase was marked by decisions taken in the 1950's to search actively for mineral and energy resources above and beyond the requirements of the steel industry. The commercial successes of this period have been Bass Strait oil and gas, Groote Eylandt manganese, Deepdale iron ore, Gregory coal and Carnilya East nickel. In total at least 22 new resource discoveries have been made in the last 25 years, of which 11 have been developed and several are undergoing feasibility studies. A financial analysis shows that the real value of the returns seeded by discovery covers the real exploration cost many times over. Moreover, the major discoveries have had a spectacular impact on the growth and development of the Company. BHP's present exploration effort is directed towards geological targets which most frequently meet attractive financial criteria and also promote diversification from steel-related earnings.

Jan 1, 1986

By A Castleden, G Cavanough, M Kochanek, J Cunningham

ROES« is a proposed new mining system for underground hard rock mines. Ore is accessed from within a shaft, which is located close to or within the stope, and pitched either vertical or within approximately 20 degrees of vertical. The shaft is designed to exclude personnel entry so production drilling and explosive placement is done using remotely controlled or automated machines. Routine remotely controlled survey of the shaft, stope back and broken rock within the stope is typically done following each blast. The survey may include excavation geometry, rock fragmentation and geotechnical characteristics. Blastholes are surveyed before placement of explosives. This provides mine operators and engineers with real-time data, allowing them to monitor production performance and risk factors so that they can make rapid changes as required. ROES« is designed to apply to open stoping or sublevel caving situations either in disseminated, geologically defined, thick tabular or narrow vein orebodies. The technologies developed for ROES« will also have potential applications to block caving operations to reduce the risk of frozen ore and poor fragmentation. In a typical sublevel open stope application, ROES« will reduce the amount of stope-associated development by about half and therefore will allow ore to be brought on-stream sooner and at significantly reduced cost. Other savings are expected to flow from the centralisation of mining activities and operational data, reduction in mining fleet, reduction in ventilation requirements, improved occupational safety and reduced mine complexity. CSIRO and Orica Mining Services are developing the required technology and AMIRA is seeking sponsorship for a project to trial the mining method. This paper details the ROES« method, expected benefits and applications and includes typical stope and mining block designs and design requirements.

Jan 1, 2008

By Okabe K

Development in the theory and practice of hearth drainage is reviewed. Difficulties in the hearth drainage were re- newed during late sixties and early seventies when the size of a blast furnace and the top pressure were increased to result in the increase in tapping rate. Hearth drainage was improved first by in- creased number of tapping and then decreased tapping rate as it was predicted by theoretical studies. State of the coke bed in the hearth, e.g., 'floating' or 'sitting-on' the hearth bottom, is discussed in relation with influential factors on it and its influence on the furnace operation. The 'sitting-on' coke bed is to be aimed at for the consistent furnace working and for the lower rate of erosion of the hearth refractory. As the continuous tapping became standard prac- tice in large blast furnaces, the interest in the basic research renewed. Prospect of the further research including mathematical modelling of the hearth drainage is discussed.

Jan 1, 1981

By Cheung L. C C, Maconochie A. P

SIROFRAG is a computer-based imaging system that quantifies the post-blast rock fragment size distribution in a muckpile in a mine environment. Improvements in blast performance and blast modelling are being hampered by a lack of a quick and objective method to evaluate the major result of the blast: the fragment size distribution. This is usually done by hand digitising muckpile photographs: a labour intensive and tedious process. SIROFRAG is being developed to quickly, cheaply and objectively provide this information. SIROFRAG is based on active stereo image analysis. It uses a light stripe to illuminate a muckpile and a pair of video cameras to determine the 3D nature of the scanned objects. The imaging system is based on a novel prototype scanning projector that allows images to he captured in full daylight. The Microsoft Windows based software controls the projector and interprets the captured images to provide a size distribution of exposed rock fragments.

Jan 1, 1995

The granulites and related "dry" igneous rocks tend to be passed over during exploration for metals. Preliminary data show that high trace concentrations of Cu, Ni and other metals of economic interest are common in orthopyroxene and some of the other granulite minerals. During retrograde metamorphism of granulites, pyroxenes are converted to amphiboles or phyllosilicates, and significant quantities of metals are released and become available for incorporat- ion into new mineral phases, or may be transported elsewhere. S--rich scapolite is the normal scapolite of granulites. Its retrogression to secondary plagioclase provides much S which scavenges Cu, Ni, etc., from pyroxenes undergoing retrogression, thus producing ore-fluids. A full analysis of a scapolite with 5.10 per cent S03 is given. Beryl is unstable in granulites but the rare Be mineral taaffeite (Al4Pf (Be,Fe)O3) with 5,50 per cent BeO occurs in central Australia as a pale green Tabular mineral easily confused for chloritoid in hand-specimen. Metamorphic differentiation and mobilization of primary ore concentrations are major factors controlling their post-granulite attitude and grade.

Jan 1, 1969

By Christie A. B, Swain A, Brathwaite R. L

This study provides quantitative data on vein distributions within seven selected epithermal systems, four deposits hosted predominantly in rhyolitic rocks: Ohui, Wharekirauponga, Neavesville and Komata, and three major deposits mainly hosted in andesite: Martha Hill, Golden Cross and Karangahake. The technique of fractal analysis was used to help quantify vein distribution patterns. The fractal dimensions (D) obtained are related to the number of veins per metre, the degree of vein clustering, and vein thickness. An increase in any of these tends to increase the fractal dimension. It is the relative relationship of these parameters that is important for the characterisation of vein distributions, and the comparison of different deposits. Within the same systems, the rhyolites are characterised by lower vein thickness and vein density, but have a higher degree of vein clustering compared to the andesites. Sections that are deeper and more centrally located within the epithermal system and/or close to major structures, tend to have a greater degree of vein clustering, higher average vein thickness and density, and higher thickness to density ratios. This depth control is most pronounced in epithermal gold-silver systems because they have formed at shallow crustal levels where physico-chemical conditions change drastically both vertically and laterally. In addition to lithological and structural control at vein scale, deposit scale structure is of great importance in the deposition of economic mineralisation. Large open vein structures capable of sustaining high fluxes of hydrothermal fluid, favourable for the formation of large, high-grade gold deposits, are best developed in andesite sequences.

Jan 1, 1995

Computers represent substantial capital investment. A better return on that invest- ment comes from more effective use of the computer's facilities. By using Telecom's data communications facilities, more people in more locations can have ready access to those facilities.

Jan 1, 1983

The excavation of a tunnel through rock and mixed ground of basalt and silty clays presents a challenge to engineering organisations. Such was the situation facing the Melbourne and Metropolitan Board of Works (MMBW) in constructing the 15.3 km, 5.5m dia. tunnel component of the new Western Trunk Sewerage System. The tunnel geology showed that there were two distinct components to the excavation - rock and mixed ground. By drawing on extensive experience in the use of Tunnel Boring Machines (TBM's) used previously by the MMBW and using techniques developed for predicting TBM per- formance, a comparison of the options of drill and blast versus TBM was made. The conclusion was that TBM methods would provide the best solution to the problem. Tenders were called for the supply of a TBM. A performance specification was used to attract tenders offering designs which re- flected the state of the art on an internation- al level. Particular features required by the MMBW were included in the specification. The excavation planning and operation are described in this paper. The production achieved has shown that the TBM can very adequately handle rock excavation (best weekly production 167.9m). Extreme conditions of mixed ground with heavy groundwater inflows have been handled using an auxiliary thrust system to maintain gripper reaction through the soft ground encountered.

Jan 1, 1987

By Braaksma M, Dudley K

The Girilambone Copper Mine is located in central New South Wales and has been operational since May 1993. Girilambone is operated by the Girilambone Copper Company (GCC) which is a joint venture between Straits Resources (60 per cent) and Nord Resources (40 per cent). The mine complex consists of an open cut pit, ore crushing and stacking, heap leaching, solvent extraction (SX) and electrowinning (EW) allowing for the recovery of 14 600 tpa of LME grade A cathode copper. The leaching and SX-EW plant have been described previously by Rear, Taylor and Busby (1994) and Miller (1994).

Jan 1, 1996