Search Documents

By J Rostami, T Afshar, M Sharifzadeh

Accurate estimation of rock load and selection of types of ground reinforcement to match post-failure behaviour of rock mass are important issues to assure tunnel stability. This paper focuses on the main factors affecting rock load to evaluate the capabilities of the existing models for prediction of rock load. Rock mass properties, project features and excavation method, as well as ground conditions and stress condition were found to be the key factors affecting the magnitude of rock load. Field data from tunnels of about 37.5?km driven in several geological structures in non-squeezing ground was used in this study. An in depth statistical analysis was performed on data to find correlations between the input parameters and measured/observed rock load. A weighting system was proposed to obtain the proper contribution of each factor for estimation of rock load in tunnelling through various ground conditions. The new classification system offered predicted values for rock load that were in a good agreement with the actual field measurements. The high disturbance factor (D>0.4) was the prime factor which controlled the rock load. Rock mass quality was the second key factor influencing rock load, which could be estimated by GSI, GSIresidual , especially when combined with tunnel depth.CITATION:Afshar, T, Sharifzadeh, M and Rostami, J, 2014. Estimation of rock load for tunnels with different disturbance factors, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The 5.6 km Canning Tunnel was constructed to improve water supply from Canning Dam to the Perth metropolitan area. The site area is in the Darling Range which is essentially a laterite-capped plateau-remnant underlain by Archaean granitic rocks, intruded by dolerite. Two arrangements were available. After geotechnical investigations which included geological mapping, seismic refraction geo- physics, diamond drilling and mechanical rock testing, a single tunnel was selected in pre- ference to two short tunnels and a connecting pipeline. The tunnel is hydraulically equivalent to a fully lined tunnel 1.83 m in diameter and 5 580 m long. The alignment diverged from a straight line so that the initial upstream section was almost normal to the contours which allowed for minimal support requirements in a weathered zone. Although steel and con- crete lining was needed at both ends, the main section of the tunnel was unlined except for a concrete floor. A sand and rock trap with a capacity of 46 m3 was constructed near the outlet portal to collect debris and sand down to a size of about 2 mm. Portal excavations were in highly to completely weathered rock which extended 56 m into the tunnel at the upstream end, and 18 m at the downstream end. Conventional drilling and blasting were used for tunnel excavation with survey control by laser. Breakage lEngineering Geologist, Mines Department, Perth, W.A.

Jan 1, 1976

By M Norbert, C Bennett

The Legacy Way Tunnel was constructed from Toowong to Kelvin Grove in Brisbane, and is the first large-scale underground excavation in the Bunya Phyllite in Brisbane. The Legacy Way Tunnel is 4.3 km in length, comprising two mainline tunnels excavated by a tunnel boring machine (TBM) with 46 connecting passages excavated between the mainline tunnels for egress provision and services. The Legacy Way Tunnel passes through two geological formations, the Bunya Phyllite and the Neranleigh Fernvale Beds. The Bunya Phyllite is the dominant formation of the Legacy Way Tunnel, extending for three quarters of the tunnel prior to intersecting the Normanby Fault Zone (NFZ) and the Neranleigh Fernvale Beds. The NFZ forms the contact between the two formations as part of the Brisbane Metamorphics, which underlies the majority of Brisbane City. The development of the geological model and the understanding of the ground’s reaction to tunnelling was an iterative process. The tender phase investigation data has been supplemented with additional design phase investigation boreholes, geophysics and walk overs. Aerial photograph interpretation coupled with borehole data allowed the development of the domains along the length of the tunnel. Early excavations for the spoil conveyor tunnel and borehole data from subsurface instrumentation installation provided the first construction phase data followed by the commencement of tunnel boring machine (TBM) excavation. Routine cutterhead inspections coupled with ongoing reviews of the predicted geology resulted in clear response triggers to selection of segment types while detailed inspections in passage locations provide the initial classifications for segment removals.CITATION:Bennett, C and Norbert, M, 2014. Tunnelling within the Bunya Phyllite of Legacy Way, Brisbane, Queensland, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 131–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Laboratory studies of batch and continuous screening of ferrous sinter mixtures (4-0.5 mm) are described. The results are analysed by an equation derived from the first-order rate law for the condition of decreasing screen residue.The results of the studies show that the two screening operations are comparable in all respects if deck length in continuous screening and time in batch screening are interchanged.It is shown that the general screening process is determined by the numerical values of the screening rate constants of each of the particle sizes in the feed mixture and that the relationship between these constants and the particle size/screen aperture ratios is related to the appropriate probability function of the same ratios.It is also shown that the screening rates decrease exponentially with the amount of near-mesh material present in the feed and that oversize particles can increase these screening rates for some screen motions and decrease them for others.

Jan 1, 1985

By S P. Young, K R. Monro

Reducing metal prices have forced mining operations to become more efficient and innovate in order to do more with the existing base. Much of this effort has focused on improving the efficiency of load and haul operations. The key to this is to understand and quantify where delays and missed opportunities exist. Metrics such as utilisation of availability, efficiency utilisation and asset availability are helpful indicators of performance; however, uptime-based time usage models and performance analysis tools using productive operating time models help to identify additional improvement opportunities.Phu Kham is a copper-gold mine operated in the Lao People’s Democratic Republic (Laos) since 2008 by PanAust Limited. The mine is a single large open pit of 450 m depth, running a fleet of 51 100 t class rigid dump trucks and 300 t and 200 t shovels controlled with the aid of a fleet management system in order to achieve ex-pit material movements of 56 Mt/a.Commencing in late 2014, a range of initiatives were implemented in order to improve the efficiency of the mine haulage fleet. These include hot seating of all operator changeouts via changeout ramps, split shifting of crews to minimise queuing delays, maximising blast volumes and minimising blast event days to reduce blast exclusion delay events including opportune refuelling of equipment during blasting events, inspections of trucks during refuelling events, implementation of a dedicated haul road services team to help reduce wet weather related delays and infrastructure development for haul path efficiency improvements.These and other initiatives have allowed the mine haulage fleet utilisation of availability (UofA) to be sustainably increased from 85 per cent to 97 per cent (see Figure 1), efficiency utilisation to increase from 85 per cent to 90 per cent, and productive operating time (POT) to increase from 73 per cent to 84 per cent. The corresponding increases in efficiency of the haulage fleet has allowed an equivalent reduction of eight haul trucks from the fleet to meet continuing life-of-mine production requirements.CITATION:Monro, K R and Young, S P, 2016. Truck haulage improvements at the Phu Kham mine – the journey to 97 per cent utilisation of availability, in Proceedings International Mine Management Conference, pp 339-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Aiming Z, Shenyi S, Xialei W

Zhangmatun Iron Mine is situated in the suburbs of Jinan city. Shandong, China. Because of surface environmental constraints, no suitable site can he selected to dispose of mill waste. The full mill tailings must be disposed of underground. This paper deals with the work conducted at Zhangmatun mine to develop a total tailings backfill system, taking advantage of a double- shaft blade mixer and an activating agitator to prepare backfill. Cement and ground slag are added to tailings for strength development. Two scopes have been filled and the pillars have been effectively mined out during the field trial. The application of innovative total tailings backfill technology is a new concept at the mine. Detailed planning has achieved a close integration of mining, milling and backfilling. Full mill tailings, with or without rock, are disposed of underground in a continuous process to fill, totally and systematically, the cavities formed by mining.

Jan 1, 1998

By G J JAMESON

The flotation cell has undergone a number of changes since the process was first introduced in Broken Hill in the early years of this century. The development of the mechanical flotation cell is reviewed, followed by a discussion of more recent developments such as the flotation column, the air-sparged hydrocyclone, the Wemco-Leeds cell, the Bahr and Deister columns and the Jameson cell.

Jan 1, 1992

By Ward B

Central Colliery was developed to exploit large underground reserves in the German Creek lease. It was planned from the outset as a retreating longwall operation and is the first longwall mine in Queensland. Longwall mining is not new to Australia but all previous experience has been confined to the coalfields of New South Wales. There was no precedent for longwall extraction in the markedly different geological setting of the Bowen Basin in Central Queensland. Various investigations were thus carried out during the initial development of Central Colliery, prior to the installation of the longwall, to ascertain the geotechnical characteristics of the coal seam and the adjacent strata and to predict the performance of the heading and pillar design as mining proceeds to depth. Laboratory tests showed the coal to be weak with an unconfined compressive strength of 9.6 MN/m2. Site inspection and geophysical correlation revealed a shear zone and extensive intraformational shear planes in the seam. The latter were found to exert a controlling influence on rib reaction in the headings. This behaviour was predicted by finite element modelling of the development headings which indicated that mining induced stresses in the coal would be relieved by block movement of the ribs. A chain pillar width versus depth curve was established for yielding pillar design based on empirical and computational methods. This gave pillar widths from 25m to 48m over the proposed depth range of 150m to 300m. Finite element modelling of the 25m pillars chosen for the first gateroads confirmed the overall stability of the design but suggested that rib spall could be significant in the adjacent tailgate. (1) Chief Mining Engineer, Capricorn Coal Management Pty. Ltd., German Creek Mine, Queensland (2) Senior Engineering Geologist, Coal Division, The Shell Company of Australia Limited, Melbourne

Jan 1, 1986

By Stewart R. D, Lawrence W, Youl M. J

The trend towards contracting by major coal mining companies such as BHP Coal and MIM Ltd is examined. Reasons why this trend is occurring are discussed and the concept of partnering is examined. Two case studies are given: the Mt Owen Mine in the Hunter Valley, NSW and the South Walker Creek Mine in the Bowen Basin, Queensland.

Jan 1, 1997

By I B. Miller

Magnesium International Limited (MIL) has broken new ground in their desire to integrate their mineral development activities in the Southern Flinders Ranges of South Australia in to the communities of the region, despite there being no statutory requirement to do so. In their efforts to define a magnesite resource adjacent to the proposed site for a magnesium metal processing facility, MIL opened their exploration program up for public consultation. In conjunction with the Port Pirie Regional Development Board (PPRDB), a community group was formed to review the impact of exploration and mining on the ecologically sensitive Southern Flinders region. This voluntary move towards full community consultation for mineral exploration was a first in South Australia and probably in Australia. The Community Focus Group (CFG) worked closely with MIL, Primary Industries and Resources of South Australia (PIRSA) and the Department for Environment and Heritage (DEH) in the development of an exploration program and Declaration of Environmental Factors (DEF) acceptable to all stakeholders. Collaboratively, the community concerns were discussed and addressed, with the community gaining a very comprehensive understanding of the exploration process and possible future mine development. A balance of social, environmental and economic factors was developed that was accepted by all parties and encapsulated in the final DEF for approval by the regulatory authority. The consultation process was a new experience for all of the stakeholders, each of them effectively exploring new ground in addressing information dissemination, risk management and the social versus economic equation. MIL developed not only a viable and acceptable exploration program but also substantially reinforced its position as a responsible corporate citizen with the Southern Flinders communities.

Jan 1, 2004

By F Soleimani

Coal and gas outburst is a common hazard in coalmines and due to the complexity of its nature, efficaciously predicting the possibility of its occurrence is intricate. The mechanical and gas flow properties of coal, in situ and mining-induced stresses and geological structure are involved in outburst occurrence, whereas suggested thresholds for its prediction do not consider them all. Numerical modelling is known as an effective method that can not only consider couple the effect of different physics but also analyse the effect of associated parameters. In this paper, a coupled fluid flow and geomechanics model has been developed in COMSOL Multiphysics to simulate outbursts by considering the effect of gas pressure and composition, damage mechanics on related coal properties, and progressive excavation and mining-induced stress. For the proposed fully coupled outburst model, the effect of pore pressure and sorption are applied to the stress while the influence of stress changes and damage are considered in updating coal porosity and permeability in each time step. In addition, to study the effect of mining-induced stress, the excavation process is simulated by changing the material properties over time according to the schedule of heading development. Then, outburst initiation is analysed from the energy point of view by using the concept of energy conservation law. The simulation results are used in calculating energy sources of the outburst initiation, also, the effect of particle size and ejection velocity are studied, and the significance of particle size effect on the energy analysis and deformed coal on outburst initiation is discussed.

Oct 12, 2022

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

ABSTRACT' Mainland Papua New Guinea is formed of a microcontinental / island arc system (?Eocene - latest Oligocene Sepic arc) which in Middle to Late Miocene times was obducted over the northward- moving Australian plate. The sedimentary and volcanic units of this system form part of the Wogamush Group (Aure beds, Mena beds, Omaura Formation, Movi beds, Wogamush beds, Wogamush Formation. Nansananka Conglomerate and other correlates in- eluding cale-alkaline volcanics and carbonate beds). This Sepic event was followed in Pliocene-Present times by the obduction of the Finisterre-Adelbert-Oenake fore-arc or possibly oceanic plateau. Obduction of the Sepic arc produced crustal thickening

Jan 1, 1997

By Harvey T, Kizil M, Bride J

Hydrogen sulphide (H2S) as a seam gas has occurred in several locations in the German Creek seam at Southern Colliery. This paper overviews the techniques developed to quantify the H2S content of the seam, overviews research into controlling and reducing H2S emissions from the seam, and details the procedures used to mine through the HZS zone in 702 longwall panel. Learning points from research and mining experience are reviewed for application in the next longwall block.

Jan 1, 1998

By B Besa, E K. Chanda

It has long been recognised that narrow vein mining needs innovative approaches to mine access and mining methods in order to improve the economics of this vital part of the mining industry. The mining equipment used currently requires large openings in narrow vein-type deposits making mining operations uneconomical. In view of this and other shortcomings of the current mining practices, a study was initiated to investigate the potential of using low profile electric loader with mounted conveyor in conjunction with the electric monorail haulage system (EMTS) to load and haul the blasted material, particularly in decline development and main haulages. Computer simulation based on the General Purpose Simulation System/Henrikson (GPSS/H) is used to model the system and evaluate its performance. The results are compared with those for conventional mining using trucks and loaders. The EMTS provides competitive haulage rates in substantially smaller excavations than is currently achievable. According to simulation results, the electric loader in conjunction with the EMTS had the same number of blasts as the conventional system and hence the same advance rate of 3.33 m per 12 hour shift. Furthermore, the total drill-blast-load-haul cycle time was less than the conventional system by one hour.CITATION:Besa, B and Chanda, E K, 2012. Evaluation of low profile electric loader in conjunction with electric monorail haulage system in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 221-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By N McIntyre, M Edraki, K R. Jain

From the very early stages of a mining project, there is a requirement to predict the chemistry of potential drainages from various waste storage facilities. However, using relative masses to scale chemical loads measured by laboratory kinetic tests, such as humidity cells, to a full-scale mine waste facility will lead to concentration predictions that are unrealistically high for many dissolved constituents. Scaling factors developed by various procedures indicate that laboratory rates may range anywhere from two to eight times (Drever and Clow, 1995) to 100 to 1000 times faster than field rates (Malmstrom et al, 2000; Smith and Beckie, 2003; Ritchie, 1994). This contribution will use previous works and secondary data to discuss the significance of scale in water quality predictions. It will also present primary experimental geochemical and numerical data from a column leaching study on coal spoils to discuss potential applications of mesoscale leaching tests in bridging the gap between bench-top tests and field scale trials.

Aug 2, 2023

By T Vizcarra, G Sandoval, C L. Evans

One of the challenges in the development of mineral processing simulators is modelling the liberation characteristics of particles produced by comminution circuits. Understanding the mineral characteristics of these particles is one of the keys to predicting their behaviour in separation circuits. While more fundamental research seeks to model the non-random breakage of ores this work examines whether we can move forward now by using observed characteristics of ores to model the composition of particles generated in comminution processes. Several researchers have noted the similarity of the liberation characteristics for a selected size fraction of particulate material, whether the fraction comes from a coarse material, such as the product from a jaw crusher, or a more finely ground material, such as the product from a ball mill. In most cases these observations were reported as an aside and were not the main focus of the published work. This observed behaviour has the potential to be a useful tool for modelling the particle characteristics in mineral comminution and separation circuits, particularly as we move towards the development of multi-component models. However, before the behaviour can be used widely we need to understand which ore types follow the observed pattern and which do not. The current work examines a range of ores and identifies which exhibit the pattern of similarity of composition for particles in a given size class that has been produced as the result of a variety of breakage conditions. The impact of mineralogy and texture on the evolution of liberation characteristics for both valuable and gangue minerals is discussed.

Jan 1, 2008

Education for the Mineral Industry in Australia developed in an uncoordinated but effective fashion till the mid 1960's, with recognised quality in graduates, with output matching demand, and with industry needs being fulfilled. Then in the space of a further 20 years, as company structures expanded, as the number, complexity, and costs of mineral projects escalated, as educational facilities, costs and politics increased, as community perceptions and aspirations changed, as government control of minerals and education increased, and as mineral sales cycles and markets fluctuated widely, the very fabric of Australian Mineral Education fell in tatters. Extractive Metallurgy Education suffered most in this collapse, and no compre- hensive remedies have been initiated. We are all the losers. In the 1990's, the extraction of Australian minerals and metals will increase in international significance, and the education of Extractive Metallurgists must meet this need. After examining the current situation, a series of management strategies are proposed to enable Extractive Metallurgical Education to survive and prosper in the next two decades and beyond. These strategic proposals involve industry, the government, the educational bodies, and individuals, in a range of short and long term objectives, policies, and actions.

Jan 1, 1984

By Egan J. R

Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant testwork conducted in 1990 - 91 indicated that concentrate grades would be substantially improved by reducing the particle size (Pao) of the lead from 38 to 15 ¦m and the zinc from 45 to 24 ¦m. Circuit revisions involved installation of major new equipment including: two 600-kilowatt Vertimills for regrinding, a four metre diametre column flotation cell and a four metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were Reassigned.

Jan 1, 1993

By B Reynolds

The process design for green- or brown-fields metallurgical plants typically starts with two fundamental elements: the detailed mass and energy balance and the plant flow availability. The detailed mass and energy balance is generally developed using process flow-sheet simulation software and represents the steady-state operation of the plant at normal operating conditions. The plant flow availability, also known as a range of other industry-specific terms such as ‘flow availability’ and ‘operating factor’, describes the ratio of plant production to the steady-state mass balance. These elements are then used together as the basis for equipment selection and design.Plant flow availability takes into account a myriad of production loss factors including planned and breakdown maintenance, feed availability and composition changes, variability in operational performance and the interaction of batch and continuous unit operations. The combined impact of these loss factors are complex and as such plant flow availability is usually derived using a top-down approach such as comparison to an existing operation, a group of similar operations or to an anecdotal ‘industry leading’ benchmark. These top-down approaches are fraught with risk however, as they cannot factor in changes to equipment selection, flow-sheet or plant operating philosophy, and can result in over-expenditure of scarce capital or shortfalls in plant production.The use of dynamic simulation to provide a bottom-up alternative to quantifying the plant flow availability in metallurgical plant design has been growing rapidly in recent years. It provides a technique to quantify the combined impact of the loss factors described here and a tool to support process design and equipment selection by facilitating a range of sensitivity and what-if analyses. This paper presents a case study of how dynamic simulation has recently been used to support the

Aug 8, 2011