Search Documents

Permian coal seams from the Tomago Coal Measures in the Northern Coalfield, New South Wales, were analysed petrographically and reflectance measurements made for each. Vitrite contents were moderate to high for most of the coals but for two they were very low.The mineral-matter contents were low to moderate by Australian standards. Different profiles of a particular seam could be correlated by petrographic methods.Standard seam profiles were drawn up and from these an idealized Tomago seam sequence was compiled. All the coals were of high-volatile bituminous rank. Their carbon contents, but not thcir reflectances, varied significantly with the quantity of vitrinite present.

Jan 1, 1968

By D Craw, D Wilson, D Chappell

Gold is extracted by cyanidation of a sulphide-rich concentrate at Macraes mine, and after cyanidation, the concentrate is discharged to tailings impoundments. The concentrate tailings were discharged to a dedicated concentrate impoundment from 1989 to 1993, afterwhich they were blended with the flotation tailings. Since mid-1998, concentrate tailings have been redirected to the dedicated concentrate impoundment. The concentrate tailings contain up to 1 ppm gold, and will be reprocessed in the future. However, it is a regulatory requirement that a contingency plan be in place to rehabilitate the concentrate tailings should the mine operation cease for any reason. Initial predictions suggested that the sulphide-rich tailings would oxidise and acidify, creating a potential long term environmental problem. Investigations of the state of the tailings after 4 years show that these predictions were overly conservative. Only minor oxidation has occurred in the upper 2 metres of the tailings where the pH has locally dropped from 10 (discharge condition) to between 7 and 8. Below 2 metres, the tailings are essentially unchanged from their deposition state. The low rate of change in the tailings is due to their very low permeability which in turn is a consequence of the fine grain size (ca. 15 ¦m). Dewatering is extremely slow, and incursion of oxygenated water is negligible. Calculations suggest that water movement over 30 m will take at least 100 years and possibly 1000 years. The contingency plan is to capitalise on the very low permeability and keep the tailings from drying with a semipermeable cap. A layer of limestone will be added to the top of the tailings, beneath the cap, to enhance alkalinity of any percolating water. If acidification does occur, contrary to expectations, any acid produced will be neutralised by underlying calcite-bearing schist, schist in the concentrate impoundment wall, and the flotation tailings immediately downstream. In addition, dilution by alkaline ground and surface waters would further ameliorate any acidic discharge.

Jan 1, 1998

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Holmes R. J, Miles J. G

An on-stream shale detector has been developed that is suitable for use on conveyor belts carrying iron ore of up to 200 mm particle size. The shale is distinguished from high-grade iron ore by means of the substantially greater total natural gamma-ray activity (400-3000 keV) of the shale, which is due to the presence of uranium (214Bi), thorium (208TI) and potassium (40K). Other gangue materials, sueh as highly siliceous cherts and jaspilites, escape detection because of their low activity. A dynamic trial of the shale detector at Mt Whaleback, using a large-volume (100 × 100 400 mm long) "Polyscin" Nal(TI) gamma-ray detector, demonstrated that as little as 20 tonne of ore on a conveyor belt (equivalent to partial truckloads of ore) can readily be monitored for shale content.

Jan 1, 1981

By Worner H. K

Education has always been a topic to rouse the interest of mining and metallurgical engineers, but the recent activities of the Education Committee of the Australasian Institute of Mining and Metallurgy 1, 2, together with the moves throughout the Commonwealth to extend the field of technological education, have made the subject a very live one at the present time. The authors have felt it would be appropriate that on the occasion of the First Ordinary Meeting for 1950, in Victoria, some contribution should be forthcoming concerning the history, present status and possible future trends of mining and metallurgical education in this State. As for the past, the time approaches when there will be none having personal recollections of the beginning of Victorian mining schools or of the men who started them. As for the future, it is obvious that rapidly expanding metal-producing and metalconsuming industries will demand a greater output of competent graduates and diplomates. The era immediately ahead seems to be bristling with opportunities, but mining educators need to temper their enthusiasm for various policies and programmes with the realisation that they are helping to train men who will be leaders 15-20 years hence when the problems of industry and trials of life generally may be very different from what they are to-day.

Jan 1, 1950

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

By Belcher C. B

A procedure was required for the rapid determination of silicon in low-alloy irons and a suitable method used the formation and reduction of silicomolybdic acid at 50°C. The procedure gives results for elemental silicon and this enables the correct computation of oxidation requirements in basic oxygen steelmaking. The method could be useful in iron foundries which have not installed direct reading spectrometers.INTRODUCTIONOxygen steelmaking experiments required rapid determinations of 0,5-1,6 per cent silicon in iron (3-4 per cent C) within 10 min of sampling; a reproducibility better than ±0.03 per cent Si was desired. Only elemental silicon (Si°) is of interest as a fuel in basic oxygen steelmaking technology, and the proposed procedure determines exclusively this form of silicon. The method is described as it may prove useful to other workers although the interference study would be incomplete for some applications.The analysis of silicon in iron is frequently obtained using direct reading spectrometers, but for the proposed experiments the spectrometers could not be used because of the prohibitive distance from the furnace. It should be noted that spectrometers determine both the elemental silicon and that present as silicon dioxide in occluded slag and inclusions.The silicon content of iron and steel is determined in this laboratory by spectrophotometric measurement of a "molybdenum blue" colour. The reactions involved have been extensively investigated; Strickland (1952) showed that a...

Jan 1, 1965

By Wylie A. W, Mathew P. J, Eisler P. L

Field studies of the radiations backscattered by iron ores from a 60Co source of primary gamma radiation located in a borehole logging probe have confirmed thatthe P" factor, a ratio of high energy gamma ray intensities to low energy intensities in selected energy windows of the backscattered gamma-ray spectrum, is a valuable measure of grade for sedimentary iron ores of the Pilbararegion of Western Australia.Laboratory studies of model boreholes have shown that variations in borehole diameter and variations in bulk density of the formations have a significant influence on the measurement of P" ratios. If these influences 'are taken into account the mean ore grade in a new blast hole, for instance, can be predicted with a probe of suitable configuration to within 0·8 per cent Fe at the 95 per cent confidence level, while the grade of a single 120-cm split can be determined to within 2·6 per cent Fe. These results were obtained by pooling data from five blast holes covering the range of iron concentrations 20-68 per cent Fe and apply to the mean hole grades 54-68 per cent Fe.Results for two development holes were generally comparable to those obtained from individual blast holes95 per cent confidence limits of ±0·9 per cent Fe for mean ore grade and ± 4·1 per cent Fe for single splits. A greater number of data points is needed before these confidence limits can be further improved.The technique utilized to obtain these results was derived from a "multiband" approach to collection of backscattered spectral intensity data, an approach which permitted selection at the data processing stage of the most statistically significant P" ratios for the type of mineralization encountered in the field. The multiband technique also permitted selection of the most significant of another set of windows in the backscattered gammarayspectrum to measure a newly developed "S-factor", a ratio sensitive to borehole diameter. Another window provided information on bulk density. All these measurements were made with a single pass of the same loggingprobe.

Jan 1, 1977

By Eggleton R. A

X-ray diffraction techniques are commonly used in the identification and quantification of fine-grained materials. A relationship exists between the size of crystals in a sample and the degree to which they diffract X-rays. The Scherrer equation relates the broadness of diffraction peaks to the size of crystals responsible for diffraction (Klug and Alexander, 1974). Relatively large crystals of the order of I - 10 ¦m strongly diffract X-rays; the diffractogram of such crystals exhibit narrow intense peaks. As the size of the crystals in a sample is reduced, diffraction peaks become broader and less intense. Crystals less than 10 nm generally exhibit broad, diffuse and low intensity peaks. Some material is so fine-grained and poorly-diffracting that X-ray patterns show very little information in a normal one-hour scan thereby necessitating very long acquisition times of up to 12 hours. The term poorly-diffracting material (PDM) was coined for such material found within the bauxite deposit of Weipa, northern Queensland (Tilley and Eggleton, 1994; 1996). Common regolith minerals such as hematite, goethite and layer silicate clays are quite commonly fine enough to possess a poorly-diffracting character. Noncrystalline and poorly crystalline Fe-Si-Al-oxyhydroxides such as allophane, opal, ferrihydrite and hisingerite, have either a nondiffracting (amorphous) or poorly-diffracting nature (Eggleton, 1987).

Jan 1, 1997

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. A deterioration in metallurgical performance at each concentrator occurred as a result, with increased loss of lead and zinc to residues. Investigations to determine the reasons for this problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical deterioration.

Jan 1, 1971

By D Craw, N Newman

Previously published stream quality data and AMD (acid mine drainage) analyses have been collated into a database (DAME û Database for Assessment of Mine Environments) and additional samples including NMD (neutral mine drainage) have been collected from coal mine drainages on the West Coast. Variations in the chemistry of mine drainage samples can be related to four factors: 1.       regional geology (Brunner Coal Measures or Paparoa Coal Measures) 2.       mine type (open cast or underground) 3.       hydrogeology 4.       local geology   In general mines hosted in Paparoa Coal Measures produce NMD whereas mines hosted in Brunner Coal Measures produce AMD with highly variable chemistry. Differences in coal mine drainage chemistry between mines hosted in Brunner and Paparoa Coal Measure sequences can be measured with acid-base accounting geochemistry. Correlation of ANC (acid neutralising capacity) and MPA (maximum potential acidity) analysis of rocks with mine drainage samples is substantially better than correlation of NAG (net acid generation) analysis with mine drainage chemistry.   It is likely that NAG analysis over estimates acid generation potential of some samples due to release of organic acids that are not released under environmental conditions. In general, differences in mine drainage chemistry between Brunner and Paparoa hosted mines are attributed to the effect depositional environment and diagenesis on coal measure composition. Exceptions to generalisations relating mine drainage to Paparoa or Brunner host rocks are likely where local geological conditions cause increased deposition of pyrite in Paparoa rocks and additional analyses are required to confirm interpretations.   Based on the interpretation of these results a mine drainage chemistry hazard model has been constructed. The hazard model predicts likely variations in mine drainage chemistry based on the four factors listed above. The hazard model has implications for mine related water quality risks. For example, ecotoxicity, human health affects and selection of remediation techniques are all sensitive to mine drainage chemistry.

Jan 1, 2006

By R L. Brathwaite

Previous paleodepth studies of low-sulphidation epithermal Au-Ag deposits in the Coromandel region indicated that economic gold mineralisation was generally limited to a depth zone of 100 to 400 m below the paleosurface. Notable exceptions are Waihi and Karangahake, where ore shoots extended to depths of about 750 and 900 m respectively. These studies have been extended to include Au-Ag, Hg and Sb epithermal deposits in Northland and the Taupo Volcanic Zone. The main paleodepth indicators used are sinters and hydrothermal eruption breccias, hydrostatic pressures estimated from homogenisation temperature measurements on fluid inclusions, and hydrothermal alteration mineralogy. Also the occurrence of lacustrine and fluvial sediments is an indicator of the paleosurface at their time of deposition. Selected paleodepth indicators have been compiled and mapped in a GIS environment. The distribution of the paleodepth indicators are used to define regional variations in erosion levels, and may be useful in predicting areas most likely to preserve the optimum depth window for gold deposition. In the Coromandel region, regional stream sediment geochemical data has also been used to broadly define erosion levels in terms of Zn, Pb and Cu representing deeper base metal zone mineralization and Hg and Sb representing shallower cinnabar and stibnite mineralisation. The interpretations of paleodepth and potential reconstruction of paleosurfaces are limited by the paucity of data, poor age control on the paleodepth indicators and the epithermal deposits, and marked relief and complex stratigraphy in the volcanic terranes.

Jan 1, 2003

The stability of parallel underground coal mine galleries and pillars have been investigated using two- and three-dimensional (3D) numerical stress analysis. Anisotropic horizontal in situ stresses and the direction of the excavations have been considered in the numerical analysis. The stability of the tunnels driven in a coal seam at various working depths has been investigated taking into account different strata conditions and then results from two- and three-dimensional numerical modelling studies were compared. Maximum principal stress components have been chosen in three various directions: vertical, parallel and perpendicular to the tunnel axis. Analysis have shown that in the anisotropic in situ stress field, the favourable direction of underground mine openings which have different strata conditions depend not only on the horizontal in situ stresses but also on the vertical in situ stresses. Furthermore, 3D numerical modelling studies have been carried out to investigate stability of multiple entry longwall panel gate roads and pillars with various width-to-length ratios (W/L). Results of the modelling studies have shown that the critical dimension of coal pillars depends on their width and the direction of maximum horizontal stresses.

Dec 6, 2010

By S R. La Brooy, T Giraudo, I C. Ritchie

The treatment plant at the Macraes Gold Project in New Zealand processes a carbonaceous, refractory sulphide gold ore. Since its commissioning in 1990, there has been a programme of continuous improvement of the plant, leading to higher recovery, increased throughput and low operating costs. During this time, a number of processes for treating both, or either, the preg-robbing carbonaceous fraction of the ore and the refractory sulfide fraction have been evaluated, trialed and utilised. The latest phase involves the installation by Minproc of plant utilising Newmont Gold's Pressure Oxidation Technology, a process which is anticipated to mitigate both problem factors when commissioned in 1999.

Jan 1, 1998

Experimental investigations were made into the decoppering of lead, tin, and bismuth using a technique which approximates on the small scale to industrial practice.Decoppering lead with sulphur alone in the absence of tin and silver did not proceed to low copper values. With a minimum of 0·02 per cent Ag or 0·10 per cent Sn, lead was decoppered to less than 0·01 per cent Cuby stirring with 0·2 per cent S over 10 min. Decoppering of tin or bismuth proceeded rapidly to very low levels in the absence of any "catalytic" impurities, at any rate in excess of those concentrations normally encountered in commercially pure tin or bismuth.

Jan 1, 1971

By Clements R. J, Davey J. M

Development of the process from the pilot stage to the current operation of the Capel, WA plant is briefly described.The design criteria for a larger sized plant are discussed together with factors that relate suitable feedstocks and coal types to the capital cost, capacity and product grade of future plants at locations other than Capel. The application of the process to the direct reduction of iron ores is briefly discussed including its commercial application at Rockwood, Tennessee.

Jan 1, 1980

Difficulties were experienced in the identification of carbonate minerals intimately associated with iron oxides in the so called carbonate ore, which occurs at depth in the Iron Duke Orebody.Determination of refractive indices by examination under the microscope using the immersion method, together with inferred chemical composition indicates that dolomite and parankerite are common constituents. Histograms of the manganese and sulphur contents strongly suggest that manganese is associated with the carbonate minerals, and that the highest sulphur assays occur near the base of the carbonate body.From the present work it is concluded that refractive indices indicate only a very approximate composition for carbonates of the parankerite type.The different carbonate minerals occur in irregular zones.INTRODUCTIONThe Iron Duke deposit is situated in the southern portion of the South Middleback Range on Eyre Peninsula, S.A., 30 miles from Whyalla. (Fig. 1).Drilling at Iron Duke revealed a large body of so called carbonate ore, which was tested in detail at cross section 1000 ft. S by three diamond drill holes, DDH.57, 67 and 78. (Fig. 2)Most specimens of carbonate ore described below were obtained from DDH 67 and 78.GENERAL GEOLOGYThe South Middleback Range is composed of two parallel ridges trending north-south. The Iron Duke orebody is situated on the southern portion of the western ridge. (Fig.1) .The rocks of these ranges belong to the Middleback Group which rests on a gneiss complex. Their age is considered to be Middle Precambrian or late Archaean.

Jan 1, 1963

The assistance that can be gained by the use of aerial photographs in the geological examination of a mineral field is clearly illustrated by the results of a rapid reconnaissance survey of the newly-discovered Mount Fitton talc, deposits, situated in the north-eastern extension of the Flinders Ranges in South Australia.The talc deposits were found to occur about the margins of a large lenticular mass of dolomitic marble, interbedded with hornfelsic tillites and fluvio-glacial sediments of Upper Pre-Cambrian age. Aerial photographs show clearly the extent of the dolomitic marble on which the growth of a species of eucalypt-Eucalyptus Gillei-is prominently developed, and which assists in defining the limits of this relatively light-coloured formation. (See Fig. 1).Upon field investigation it was found that the talc, deposits are related closely to the margin of the dolomitic marble where the latter has been subject to minor folding and faulting. The deposits themselves have been formed by metasomatic replacement of schistose dolomite. The contact of the dolomite with the underlying and overlying glacial beds is also noteworthy for the presence of minor occurrences of copper, silver, lead and zinc minerals.An examination of photographs covering a wide area reveals an outcrop of a massive granite to the north-east of the dolomitic marble, Fig. 2, which was almost certainly responsible for the regional metamorphism of the dolomitic and glacigene sediments, and the source of the mineralising solutions.All these features, as well as the broader structural features of the area, which are extremely important in the understanding of, individual commercial depQsits, were quickly determined with the assistance of the photographs.It is useful, briefly to relate the procedure adopted in examining this recently developed field as an example which may be well worth following on other fields, even if exposures are not so clearly defined. The method to be outlined, of course, will be of maximum advantage. Where rock exposures are good, where the ore bodies are likely to be widely spread, and where such bodies are related to some major geologi-cal control. Typical of such deposits are pegmatitic, hydrothermal and related ore bodies associated with the periphery of an igneous intrusion, or ore bodies related to particular sedimentary horizons in a regionally metamorphosed province.Procedure.The first requirement is the preparation of a detailed reconnaissance geological plan of as large segment as possible of the potentially mineralised province. The use of aerial photographs is par...

Jan 1, 1950

By S Jokanovic, J L. Mauk

The Taharoa ironsand deposit covers approximately 16 km2 and is located 144 km south of Auckland on the west coast of the North Island, New Zealand. The heavy mineral-rich sands predominantly contain titanomagnetite, ilmenite and hematite, along with lesser amounts of amphiboles, pyroxenes, and feldspars. Throughout the Taharoa mine site 142 samples were collected of which approximately 25 samples were used in mineralogical analyses of the magnetic, heavy non-magnetic and light non-magnetic fractions. Mineralogical and petrographic analyses confirmed the high abundance of homogeneous magnetite and magnetite containing ilmenite exsolution lamellae which have oxidised to hematite. A limited number of sand samples were collected from Taranaki beaches. Petrography reveals exsolution textures of magnetite and ilmenite (now hematite), and homogenous magnetite grains similar to those observed at Taharoa. Petrographic analyses from previous research projects were also closely investigated in order to make mineralogical comparisons from along the west coast of the North Island and with other potential source areas. The origin of detrital magnetite grains along the west coast of the North Island is generally presumed to be the eroded volcanic cones of the Egmont volcanoes and active and dormant volcanoes of the central North Island. Electron microprobe analyses of magnetite grains from Taranaki beach samples reveal TiO2 values of between 1.5 and 120 per cent. MgO and A12O3 contents also vary widely from 0.75 to 6.5 per cent. This large variability may reflect different volcanic eruptions, the presence of exsolution textures or alternative source areas for these magnetite grains. Geochemical results from the Taharoa mine site correlate with the Taranaki beach samples suggesting that the Egmont volcanoes are certainly one source area. Variability in XRF results, especially Fe and Ti contents (9.04 - 59.22 and 0.80 - 4.64 respectively), from the magnetic and heavy non-magnetic fractions likely reflect the detrital nature of this deposit.

Jan 1, 2003

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975