Search Documents

Effectiveness of Lead as an Alternative to Copper Activation in Gold Bearing Iron Sulfide Flotation

Sep 13, 2010

Geological Parameters Controlling the Improvement of Manufactured Sand Using Vertical Shaft Impact Crushers Instead of Cone Crushers Natural sand is a limited resource. In Sweden the total use of natural sand and gravel is around 20 million tonnes per year and the goal is to halve the use of this resource in the near future. Most of this natural sand is used for concrete production, so the consequence of this goal is that more and more concrete must be produced with manufactured sand. The bedrock of Sweden consists mainly of granites and gneisses, rock types mainly composed of various amounts of quartz, feldspar and mica. Manufactured sand from these materials generally contains rather flaky and elongated grains, and there are few types of granite that can be used as manufactured sand in concrete without increasing the amount of cement by eight to ten per cent. A Vertical Shaft Impact crusher (VSI) is commonly used to improve the shape of coarse aggregate particles. Research has shown that it is even possible to improve the shape in aggregate fractions less than 1 mm for some rock types. The aim of this project was to investigate which geological parameters control the improvement of manufactured sand when using VSI-crushers instead of the traditionally used cone crusher. In order to do this eight rock types of granitic composition were investigated. The selection of rock materials for the tests was based on grain size and mica content. A 4 - 8 mm fraction of each material was used for the tests. The characterisation of the shape of the material was performed using image analysis applied on microscopic images. The results showed that the VSI-crusher had improved the shape of all materials down to 0.036 mm, except for one rock sample. According to these results granites with low mica content and relatively high content of feldspars have the best prerequisites to produce manufactured sand for concrete with suitable geometric characteristics, and if these materials are crushed with a VSI crusher they almost show the same characteristics as natural sand.

Sep 13, 2010

By W Blair, J Bosman

The measurement of ferrosilicon rheology and characterisation of the parameters that have a direct influence on medium rheology provide the basis for evaluating, comparing and selecting an appropriate size and shape of medium to maximise separation efficiency in a dense medium application. The role of medium viscosity on particle separation in both static and dynamic separators is illustrated using relevant theory. The primary measurements of rheology are medium viscosity and stability. These in turn are determined by particle size, particle density and particle shape which in turn can be quantified. Additional characterisation parameters are also discussed. Different areas of application where ferrosilicon characterisation can be used are also discussed.CITATION:Bosman, J and Blair, W, 2017. The practical characterisation of ferrosilicon for dense medium applications, in Proceedings Iron Ore 2017, pp 135–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Site specific geotechnical data, deposit characteristics and method of mining are key factors when assessing an appropriate slope design philosophy. Mining geotechnics should be viewed as an iterative design process linked closely with mine planning, development and operational safety constraints. This case study presents geotechnical investigations for slope design at Macraes Flat Gold Mine using kinematic, probabilistic and economic analyses tempered with knowledge of site specific conditions. The recommended designs not only reduce early waste stripping tonnages but also provide data to optimise final walls.

Jan 1, 1992

By D A. Manhire, R M. Flores

The commercial develop of coalbed methane from the Powder River Basin has demonstrated that low-rank coals can be a viable source of gas. Currently over 20 000 coalbed methane wells exist in the Powder River and it is predicted that there will be 50 000 wells by 2010. What makes the Powder River Basin successful is the thickness of the coal (in excess of 30m) as well as the low ash content (

Jan 1, 2002

The demand for gallium has increased significantly over the last few decades due to the expanding use of Ga compounds in the electronics industry. Because it is widely dispersed and rarely found naturally in concentrations greater than 0.1%, Ga is expensive (approximately US$500/kg) and difficult to produce in large quantities.   A previous study of metals in geothermal systems reported significant quantities of Ga present in the muds on the northeast margin of Lake Rotokawa, an acidic lake associated with a high-temperature geothermal field situated in the Taupo Volcanic Zone of New Zealand. Similar muds are present in many other geothermal fields in the zone, suggesting that geothermal muds could be a commercial source ofGa.

Jan 1, 1994

The extent to which man's activities are influencing the earth's climate is subject to considerable debate. Internationally however, this debate has been put aside somewhat by the Kyoto Protocol. This international agreement is the political response to the threat of Global warming, predicated on the precautionary principle.NZ is seeking to be a leader in the Kyoto Protocol. Given our unique GHG emission profile and the structure of our economy, and the major uncertainties in both the science of climate change and the Kyoto Protocol itself, this desire to lead is absolutely inappropriate in this instance. We face a different, and often more severe, set of challenges in an economy that prices C emissions than virtually all of our trading partners. Unfortunately, these differences have not been reflected in climate change policy development to date. This represents a major threat to New Zealand's economy, wealth and jobs, particularly in the sectors that have been the core drivers of our economy over the last 20 years or so - agriculture, energy, primary processing. We do not, and should not, seek to avoid the issue but we must protect our economy and move with or follow our trading partners and competitors, not lead them.

Jan 1, 2002

By D Nicoli, P Feltoe

The operation of grinding circuits are vital to the success of most mineral processing operations in the provision of effective size reduction whilst maximising throughput. However these same circuits, and especially semi-autogenous grinding (SAG) mills, are highly interactive with product re-circulations and long time delays. This makes the optimal control of these difficult by conventional controllers, such as PID, which generally places a heavy reliance upon operations for control. In order to account for the peculiarities (such as ore type changes) and the abnormal situations that continually beset these circuits, it is necessary to adapt linear control techniques to cater for these situations. The Honeywell Hi-Spec Solutions SmartGrindTM controller is a marriage of multivariable predictive control (MPC) with techniques that provide adaptation of the control to optimise the circuit under all conditions. Optimal control is achieved by incorporating pattern recognition techniques to detect and act on discrete events (eg ore type changes) and adaptation of the MPC to account for known process and equipment non-linearities. AlcoaÆs Wagerup Refinery is the first site worldwide to have this technology applied to the SAG milling circuits and this has resulted in throughput increases in excess of two per cent and significant improvements in circuit operations. This paper describes the implementation of the control to the refineryÆs Mill 3 bauxite grinding circuit and the capacity/operational improvements achieved thereof.

Jan 1, 2000

Application of Natural Zeolite for the Removal of Diethylenetriamine (DETA) and DETA-Metal Complexes from Flotation Process Water

Sep 13, 2010

Advanced Jig Separation of Shredded Plastics The authors have reported that the RETAC jig is very useful in separating relatively low density particles such as plastics, and demonstrated that highly efficient jig separation of plastic components in discarded office machines is possible in pilot-scale tests. To further improve the separation efficiency, a hybrid jig (RETAC jig with air bubbler under the particle bed) which can separate plastics having similar specific gravities using differences in wettability produced by a pretreatment, and a reverse jig (modified RETAC jig for plastics lighter than water) were developed. This paper reviews the separation of shredded plastics using advanced jig separation technology (RETAC, hybrid and reverse jigs). Wettability control of the plastics for the advanced jig separation is also reported.

Sep 13, 2010

Study on Oil Agglomeration Flotation for Deinking

Sep 13, 2010

By J S. J van Deventer

Geopolymerisation is a new technology that processes and transforms aluminosilicate minerals into mechanically strong and chemically stable products. In this investigation, minerals such as fly ash and kaolinite were used as the solid raw materials for geopolymerisation. Inorganic salts were added to the geopolymeric pastes to simulate ionic contamination during processing for building and construction applications. The resultant products were examined and characterised physically. It was found that the early strength development of geopolymeric pastes could be changed according to the nature as well as the extent of the contamination. At a small dosage, the effect of the contamination on the early geopolymeric system depended heavily on the nature of the artificial surfaces that were created in the geopolymeric solution through the addition of the chemical additives. For example, the samples containing MgCl2 and Mg(NO3)2 had shown the same yield stress developments due to the similar surfaces that were formed. The cations of these salts were expected to hydrolyse and form magnesium hydroxide precipitates immediately after the addition to the early geopolymeric systems. The calcium cations of CaCl2 also precipitated upon addition, but the nature of the surfaces of these hydroxides was quite different to those of the magnesium hydroxides and gave rise to different yield stress development. The samples that contained the insoluble salts (in water) demonstrated different yield stress development when compared to each other because of the different nature of the additive surfaces that were exposed to the geopolymeric solution. These results suggested that heterogeneous nucleation could be responsible for the change of the rheological behaviour upon inorganic salt addition. When the extent of the ionic contamination was large, the anions released from the insoluble salts (in water) changed the nature as well as the concentration of the geopolymeric solution and the setting processes were retarded. Oxides, in general, behaved very differently from other salts, indicating the uniqueness of the oxygen anions in a system rich in hydroxyl and silicate anions. The inorganic salt contamination in geopolymers did not show any significant signs of structural change according to the XRD diffractograms collected. The seven-day compressive strength was not lowered by the inorganic salt contamination and it could sometimes be beneficial to the product performance, for example, an increase of 20 MPa was induced by the addition of calcium oxide. Inorganic salts as chemical additives have demonstrated the potential to modify setting times of geopolymers without sacrificing much of the productsÆ strength and integrity.

Jan 1, 2000

By M I. Pownceby, S Hapugoda, V Nunna

Deposits of low-grade iron ores containing abundant goethite are distributed across the world. A common difficulty associated with beneficiating goethitic-rich ores is the poor liberation characteristics of the iron-bearing minerals which often contain finely disseminated gangue minerals such as kaolinite, gibbsite and quartz. Microwave-assisted heating has been proposed as an effective way of inducing dehydroxylation and associated mineral transformations in order to beneficiate low-grade goethitic ores. In this research, the mineral transformations occurring in a low-grade goethite-rich sample using microwave radiation was studied. Roasting conditions (up to 1000°C and under various CO/CO2 gas atmospheres) were designed to generate a magnetic product from a goethite-rich, reject waste stream sample sourced from an iron ore processing site in the Pilbara, Western Australia. Conditions (T, pO2) for transforming the raw material from hydrated goethite to hematite and eventually to magnetite are presented. Chemical and mineralogical characterisation of the raw material and roast products were conducted using X-ray fluorescence, X-ray diffraction, optical microscopy and scanning electron microscopy techniques to identify the mineralogical and chemical changes occurring during the heat treatment. Further steps are suggested to optimise the microwave-assisted magnetising roasting and correlate it with the application of magnetic separation techniques to maximise the efficiency of upgrading the iron content in low-grade iron ores.CITATION:Nunna, V, Hapugoda, S and Pownceby, M I, 2017. Study of microwave-assisted magnetising roasting and mineral transformation of low-grade goethite iron ores, in Proceedings Iron Ore 2017, pp 575–582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Separation of Minerals Using Electrical Fields The mineral processing industry requires alternative separation techniques to help deal with rising energy costs and decreasing ore grades. Dielectrophoresis is one possible technology. It uses non-uniform electrical fields to separate particles on the basis of their permittivity. In order to determine its viability, the dielectrophoretic force was measured for individual chalcopyrite particles in ethanol. The measurements were made by attaching the individual particles to glass fibres and measuring how far they were deflected by a non-uniform electrical field. Six sizes of chalcopyrite particles were tested and the force was found to increase as a function of particle radius cubed. The particles were also positioned at different points in the field in order to determine the effect of the electrical field gradient. The force was found to increase with the inverse cube of the distance from the centre of the particle to the pin electrode. With the effect of these parameters fully characterised, the single particle test cell can be used to determine the permittivity of single particles of various composition.

Sep 13, 2010

By P F. Lauricella, D Hendri

In the Mesel sediment-hosted disseminated gold deposit, the spatial distribution of hydrothermal alteration is controlled by steeply dipping faults and shallowly dipping lithologies. Hydrothermal alteration of carbonate rock is characterised by decalcification, dolomitisation and silicification. Intense argillic alteration occurs in a laccolithic andesite intrusion adjacent to decalcified and silicified carbonate units. Sulphide minerals (pyrite, realgar, orpiment, stibnite and cinnabar) accompany hydrothermal alteration and precious metal mineralisation. The trace elements Ag, As, Sb and Hg are zoned spatially throughout the deposit. Mesel contains a mineable gold reserve of 7.8 million tonnes at 7.3 g/t Au. Gold mineralisation is preferentially localised in carbonate rocks adjacent to and beneath the andesite intrusion. The ore body consists of a central, near-vertical, high grade 'feeder' system flanked by tabular, inward dipping, moderate grade 'ouflow' zones. Mineralisation is controlled predominantly by two steeply dipping faults with high grade (=10 g/t) gold zones centred about structural intersections and fault splays. Gold is submicron size and locked in very fine grained (<10 microns), disseminated and fracture-controlled arsenical pyrite. The Mesel deposit developed where high angle faults guided ascending, sulphidising fluids into reactive carbonate stratigraphy adjacent to and beneath the andesite intrusion and during subsequent migration of the auriferous fluids along 'outflow' channels. Early decalcification and dolomitisation enhanced porosity and permeability prior to silicification and sulphidation. Gold deposition occurred late in the genesis of the deposit.

Jan 1, 1995

By I P. Hodkinson

SMC Resources Limited is implementing a selective mining approach at the Hadleigh Castle mine, formerly operated by Aurora Gold Limited. The main ore zone has a length of 250 metres and dips at 40 - 45¦ to the south. Gold mineralisation occurs in a variety of quartz-sulphide lodes in sericitised granodiorite. Shallow dips, alteration intensity and mineralisation style combine to make mining relatively difficult. Previously unworked, high-grade, shallow dipping (30 - 45¦), narrow quartz-sulphide lodes within the hanging-wall of the deposit are also being selectively exploited. Annual production of 35 000 oz Au is forecast from 185 000 tpa ore grading 6.5 g/t Au over a currently envisaged mine life of six years. Operations completed to-date include deepening the decline and access development of the first two levels beneath the previous workings. Longhole stoping operations have commenced in the main ore zone with air leg stoping also underway in the hanging wall lodes.

Jan 1, 1998

By S Henderson, J V. Lawless

The worldwide association of low-sulfidation epithermal gold mineralisation, bimodal rhyolitic-basaltic volcanism and rifting is confirmed in New Zealand. In the currently productive Coromandel epithermal-gold province reported Ar-Ar dating of adularia from low sulfidation deposits falls into two groups at 6 and 7 Ma. Bimodal rhyolitic-basaltic volcanism has been reported to be K-Ar dated at 9 to 7 Ma and 6 to 5.5 Ma. Epithermal gold mineralisation in Northland is spatially associated with bimodal basaltic-rhyolitic volcanism, with rifting cogenetic with that in the CVZ. The Taupo Volcanic zone (TVZ) is sufficiently young that the presence of a segmented rift with recent bimodal rhyolitic-basaltic volcanism can be genetically associated with epithermal gold mineralisation, which occurs as both fossil occurrences and in active geothermal fields. This reinforces the known potential prospectiveness of the Coromandel area and increases that of Northland and the Taupo Volcanic Zone.

Jan 1, 2005

Jan 1, 2004

Though many mining and mineral processing companies have embraced the principles of sustainable development (SD), there is still a significant challenge of applying these in a practical sense, either in plant design or as part of day-to-day operations. The high-level nature of sustainability concepts often do not translate easily into workable activities or business case evaluations. This makes it difficult for engineers and company decision makers to understand whether their actions are making a contribution to sustainable development and a long-term business case. While several organisations have their own SD tools that can, to a degree, help identify these opportunities, they are largely ad-hoc and lack the necessary thoroughness to defensibly value these opportunities. Recognising these serious shortcomings, the Cooperative Research Centre for Sustainable Resource Processing (CSRP) has undertaken the development and trial applications of SUSOP« (SUStainable OPerations), a new concept that is somewhat analogous to HAZOP and the wider risk and safety frameworks used in projects today. The key goal of the SUSOP« research project is to produce a holistic, systematic and rigorous framework for project development, capturing, recording and evaluating SD opportunities and constraints against a chosen sustainability structure (eg Five Capitals). SUSOP« is being developed through an iterative process with input from research institutions and engineering companies. This integrated approach ensures that SUSOP«, in its final form, will have the academic rigour and industry realism required to assist the resource sector contribute to societal sustainability by embedding the concepts and processes into the design and operation of their assets in a meaningful and practical manner. SUSOP« has created much traction with both engineering companies and mining and minerals operators. This conference paper presents an overview of the SUSOP« framework and its current suite of processes as well as highlighting, through practical case studies, its capability to incorporate SD considerations at different phases of an engineering project's development.

Jun 1, 2010

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010