Search Documents

By James J. Wise

INTRODUCTION One basic design feature utilized in all caving and sublevel stoping techniques is the drawpoint. These draw- points may be located on sublevels when using sublevel caving methods, or may be located at the floor pillar when using block caving, sublevel stoping, or vertical crater retreat methods. How the drawpoint is designed and developed, how the ore is withdrawn from it, and how the ore is hauled to the shaft or portal encompasses the loading and hauling function. Historically, predominate loading and hauling equipment for caving and sublevel stoping has been scraper slushes, air powered overshot loaders, and rail mounted train haulage. All of this equipment has two common constraints. 1. The equipment locked into specific work sites and is not easily shifted to another work site. This constraint can often lead to low utilization and low productivity of the equipment. 2. The equipment is designed to work in the horizontal plane, which requires that the various horizontally-oriented working levels be connected by vertical raises. Vertical development by means of raises is not only increasingly expensive, but also is not well adapted to movement of large equipment into the s topes. In the last 20 years, two revolutionary labor saving concepts have become common in caving and sublevel stoping. 1. Long-hole drilling, which has mechanized the development of the drawpoint extraction structures as well as the actual stoping and undercutting. 2. Vertical access by means of trackless ramps between levels, and the consequent use of rubber-tired vehicles not only for loading and hauling ore, but also for the rapid movement of men, material, and equipment into the stopes. The introduction of trackless mining systems for loading and hauling has not been easy. Mine planners have had to re-orient their thinking to the larger operating space required by trackless equipment. Larger access drifts have necessitated reconsideration of mine layouts to insure proper ground support. Spiral ramp developments were often laid out on slopes steeper than the equipment could negotiate economically. Mine operators had to accept the added responsibility of roadway maintenance, water removal, increased ventilation, and more technical mechanical maintenance. As the mine operators enthusiastically embraced the superior productivity of trackless mining systems, they some- times disregarded opportunities to combine the older types of equipment with trackless vehicles to maximize productivity at lowest cost. In order to gain a proper perspective on this problem, it is necessary to review the various techniques of loading and hauling and to become more aware of the advantages or disadvantages that each system or combination contributes. LOADING Loading consists of two functions, (1) primary loading from a drawpoint and (2) secondary loading into long- haul system, a truck, train, or possibly a belt conveyor. Mine planners have four basic loading systems available to fit various operating conditions. These are, (1) gravity, (2) scrapers, (3) rail-mounted loaders, and (4) trackless loaders. Each system can produce optimum results under specific conditions. Gravity Loading Gravity loading is probably the oldest system in general use today.

Jan 1, 1981

By Robert L. Gower, John H. Cash

Interconnections for integrated circuits operating at rnicrowaue frequencies rzust be formed as microwave transmission lines. This paper describes the fabrication of one type of microwave transmission line known as microstrip, which can be fabricated on momlithic integvated circuits by deposition of 0.1- to 2.0-mil-thick metal and dielectric films. A microstrip line consists of a narrow conducting strip separated from a gvound plane by a dielectric material. Thick films of good conducting materials are required for low loss at high frequencies. Vacuum-evaporation methods for depositing aluminum and silver films are described. The narrow conducting strip forming the top conductor is defined by photoresist-etching techniques after the thick rnetal film is deposited. Gold plating with a photoresist-masking technique is also used to forrrz thick metal conductors. The microstrip dielectric layer is formed by deposition of suitable dielectric films 0.1 to 2.0 mils thick. Several deposition techniques were investigated. Electron-beam evaporation of quartz is described. Electrical characteristics of deposited microstrip lines at microwave frequencies are included and the microwave power attenuation as a function of conductor and dielectric thickness is given. It is concluded that the deposition of microstrip transmission lines is a practical way to achieve low-loss interconnections in monolithic integrated circuits. CONNECTIONS between devices in low-frequency and digital circuits are usually made by connecting the devices with a length of conductor such as a metal lead oi- a wire. If this method were applied to microwave integrated circuits, the reactance of the connection due to the series inductance and parasitic capacitance would be very high, in fact too high to permit successful circuit operation. In addition, resonance and antenna effects would occur at high frequencies, especially when the connections approach the wavelength.' Connections which are sections of transmis- sion line will overcome these difficulties. The electromagnetic field is confined to the volume of the transmission line, parasitic effects are not present, and circuit design utilizes familiar transmission-line techniques. TRANSMISSION LINES One type of transmission line geometrically adaptable to integrated circuits is known as micrstri. A microstrip line can be generated from a coaxial line as shown in Fig. l(a). The outer conductor of the coaxial line is distorted into an ellipse (b) and finally separated at the extremities of the ellipse to form the strip transmission line shown in (c). One of the ground planes is then removed, leaving a conducting ground plane and a narrow conducting strip separated by a dielectric. Two configurations of the microstrip line were considered in this investigation, Fig. 2. Type (a) is fabricated from a semiconductor slice with the ground plane and top conductor deposited on each side of the slice. The semiconductor slice serves as the die lec-

Jan 1, 1967

By David H. Carlson, John H. Johnson

The paper presents background information, a description of mine characteristics that affect air monitoring techniques, and a review of Portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the experimental mine, the diesel dilution tunnel test cell, the mine air monitoring lab (MAML), portable instruments, and the production mines used.

Jan 1, 1982

By J. G. Thompson

THE methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value represent-ing the sum of the oxygen contents of several or all of the oxide con-stituents present. With such diversity in the principles and. aims of the different groups, it is not surprising that concordance of results by differ-ent methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the vari-ous methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metal-lurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1936

By William I. Rau

This presentation will examine the role commercial banks will be expected to assume in financing international minerals projects, including a discussion of various financing techniques such as project loans, production loans, and production payments. A discussion of the necessity for completion guarantees, finalized sales contracts, reserve evaluations, management contracts, and marketing undertakings in conjunction with financing availability are also included.

Jan 1, 1981

By Albert Sauveur

(Winces-Barre Meeting, June, 1911.) THE instrument about to be described meets so perfectly the special needs of the metal microscopist that there seems to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.-The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement' affords free space below the objective for the examination of large specimens of metals, such as full rail-sections, without detracting in the least from the value of the instrument when applied to the examination of the usual small specimen, as explained later. Many metal microscopists frequently have to examine bulky specimens, and this is altogether impossible with the ordinary microscopes as well as with the special metallurgical microscopes which have been designed and described from time to time. Recourse must be had to all sorts of makeshifts for the proper support of large specimens, or, more often, the microscopist gives up the attempt altogether, or else resigns himself to the cutting of the bulky samples into small pieces to -be laboriously polished and separately examined. It is believed that an instrument permitting the examination of large as well as of small specimens with equal ease and accu-

Dec 1, 1911

By D. M. Lewis, R. C. Emmett, B. C. Wojcik, F. A. Baczek

The ElectroSlurry™ electrowinning concept has been incorporated into a process flowsheet for recovering copper from smelter flue dusts. The process has averaged 96% recovery of the copper as high-grade electrowon cathode, while at the same time removing a majority of the impurities that degrade drawn copper as a result of recycling flue dust and liberator cathodes. The dust is processed through several stages consisting of leaching, copper precipitation, ElectroSlurry electrowinning, and waste liquor treatment. The process may be integrated into a smelter operation and become an effective and feasible means of maintaining good product purity.

Jan 1, 1981

By George W. Becker, Blair R. Benner, Ronald J. Roman

A computer model for the leaching of oxide copper heaps is developed and verified in laboratory tests. The model can be used to scale-up laboratory test data and to simulate the results of various operating philosophies on heap leaching. The model is applicable to leaching processes where the rate of leaching is controlled by a deficiency of reactant or diffusion of a reactant through the leached rock. Several examples are presented showing the sensitivity of the recovery vs. time curve to the variables in leaching.

Jan 1, 1975

By Shigeki Nishimura

INTRODUCTION In this gapes, the author will describes to development of Yubari New coal mine. The construction set about since October 1970, and commenced from June 1975 in winning. Especially, descrives to compare with the studies at planning stage, and the experiences at under construction. The problems for development are next four: 1) There were no outcrop of the coal bearing strata, but the development was instituted against the deep coal seam occurrence at 800 m below the surface. 2) In order to the coal seams occured the deep level from the surface, threr had very difficult problems, i.e. temperature, earth pressure, methane etc. The countermeasure to solved them, were foundation of the development. 3) The construction was afflict with the inundation in high pressure, due to cement grouting and excavating alternately, overcame the difficulties. 4) The construction was finished by the encourage of national investment, in spite of the enterprise was weaken constitution from the energy revolution since 1960's. OUT LINE OF YUBARI NEW COAL MINE Geography Situation. Ishikari coal field is situated the west side of the Hidaka mountains, where runs north to south at center of Hokkaido, northern district of Japan. It's width is 40km in east and west, and length is 110km in north and south.

Jan 1, 1976

By James Kemp

(New York meeting, February, 1913.) IN the study of ore deposits water plays a very prominent part. The small group of igneous ores involve it least, but in all the rest it is an invariable feature. The ground-water, therefore, is perhaps as appropriate a subject for discussion before a session of the American Institute of Mining Engineers as any topic which might be selected. The theme is if anything the more appropriate, because two very important contributions to it have already appeared in the Transactions. The great essay in 1893 of Franz Posepny,1 systematized and classified the subject, and was doubtless not without its influence in leading to the presentation in 1900, by C. R. Van Hise, of an important contribution entitled Some Principles Controlling the Deposition of Ores.2 We all recall the discussions of 10 or 12 years ago, and the interest in these themes which then prevailed in the Institute. They are collectively accessible in the separate edition wisely assembled by Dr. Raymond, and now to be supplemented by the Emmons Volume. Views have been progressing in the past decade or more, and new evidence has been brought to light. A general summary and concise statement may, therefore, not be without interest.

Jan 4, 1913

By Donald L. Birkimer

GENERAL INTRODUCTION To paraphrase comments made by Black and Hoek(1) on the status of rock mechanics, the general methods of applied science related to rock mechanics are: a. Observe the phenomena of nature as they occur and, wherever possible, quantify the observations. b. Propound a model or theory to explain the phenomena observed. c. Test and develop the theory by further experimentation in the laboratory and in the field. d. Use the theory developed to predict behavior in similar or extended circumstances. e. Insure by measured experiment and observation that the predictions made are valid, or that deviations from the predicted behavior can be accounted for. f. Modify the theory and practice as necessary, and continue the process until more general laws can be formulated and applied, with a useful degree of confidence, to practical problems. This paper will present an infant concept. It will, in fact, propound a possibly useful theory to help explain commonly observed phenomena. It will test and develop the theory for a material similar in nature to some rocks. It will be used to predict behavior in the extended circumstances of a

Jan 1, 1971

Discussion of the paper of WALTER 0. SNELLING, presented at the New York meeting, February, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. F. LUCAS, Washington, D. C.-Are the results of the experiments in practical operation? WALTER 0. SNELLING.-There have been no large-scale operations up to the present. The necessary conditions of temperature are easily arranged for, but the required condition of pressure, 800 lb., is not so simple a matter. The company has been working on this problem, and at the refinery in Oklahoma work of this kind is now being carried on. The way in which an ordinary still will leak at 50 lb., and more at 100 lb., leaves some doubt in the mind of many as to what can be clone at a continuous working pressure of 800 lb. On the other hand, the fact that they are making ammonia abroad by a method which employs higher pressures and temperatures than anything involved in this method, leads me to believe that the difficulties, which will undoubtedly arise when this is attempted on a commercial scale, can be overcome. WILLIAM N. BEST, New York, N. Y.-Is there any change in the calorific value of these oils?

Jan 5, 1915

By T. P. Oxford, G. Y. Onoda, E. D. Whitney

Disposal of phosphatic clay waste slurry has been a problem since the advent of hydraulic processing of phosphate rock in Florida. Alternatives to the present practice of storing slimes behind earthen dikes have been earnestly sought for more than a quarter of a century. Seepage dewatering is a promising technique intended to increase waste clay solids content to a level sufficiently high to permit clay disposal in mine cuts, in lieu of above-grade impoundment. An experimental array of vertical seepage columns containing mine tailings sand was constructed. Significant improvement in waste clay dewatering relative to that occurring in a control test was observed when approximately 1800 m3 of waste clay was disposed of in the presence of the seepage aids.

Jan 1, 1983

By T. E. Burke-Gaffney

SHERRIT Gordon Mines transplanted a 2000- ton mining plant and concentrator along with a town and its people 165 miles into undeveloped and almost inaccessible country in shifting its base of operations to the new mine at Lynn Lake. Faced with ultimate exhaustion of its ore bodies at Sherridon, Manitoba, the company, beginning in 1938, carried out an intensive program of prospecting and exploration in search of a new property. Late in 1945, diamond drilling of a magnetic anomaly near a minor surface expression of metallic sulphides gave promise of what has developed into the Lynn Lake nickel-copper deposit.

Jan 6, 1953

The practice of fine-grinding is now being so succeesfully carried on in some fields, notably in West Australia, and its advisability has been so frequently pointed out,l that the matter in this paper is not put forward as new; its chief object being to call attention to the importance of fine-grinding in the treatment of comparatively low-grade oree. I' have been engaged daring the last five years in the cyanide-treatment of ores in the Ohinemuri district (North Island), New Zealand, and I consider that, in the near future, extremely fine-grinding (almost sliming) will become a very im-

Jan 1, 1906

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325. As part of this giant effort, the smelter planning team and supervisory staff considered that new, well organized, highly flexible, readily available maintenance information was essential to assist the maintenance personnel in the performance of their duties.

Jan 1, 1979

By Eugene W. Pearson

In a marked departure from conventional practice, the Power Plate process combines the two unit operations of leaching and electrowinning into a single continuous step for direct recovery of copper from sulfide concentrates, cement copper, copper scrap, and copper oxide slurries. Considering how environmental controls are pre- venting development of smelters for additional capacity or new construction, the Power Plate process provides a welcome pollution-free alternative to the smelting-electrorefining routes. And its low capital investment and low operating costs also recommend it to copper producers who are now using or investigating various hydrometallurgical methods.

Jan 12, 1974

By Richard Birk

Rf sputtered quartz has been successfully used in multilayer interconnects for MOS devices. The target potential was 2000 v peak to peak with a frequency of 13.56 Mc per sec. The sputtering rate was approximately 60A per min with an operating pressure of argon gas at 10 to 15 p. The dielectric strength is 8.0 x 10' v per cm and the pinhole density is less than 2 x 10-2 per sq mm. Infrared absorption peaks for the Si-O vibrational bands we at 9.4, 12.4, and at 22.5 p. The etch rate of the sputtered SiO2 is 1200A per min. MOS devices have been fabricated using multilayer interconnects with no degradation of electrical characteristics. MULTILAYER interconnects require an insdating film between the metal layers which can be deposited below any potential eutectic temperature. Sputtered Si4, which can be deposited with substrate temperatures below 200°C, satisfactorily meets the multilayer insulation requirements and has been used to prepare MOS circuits with multilayer interconnects. The physical and electrical properties of rf sput-

Jan 1, 1969

By B. B. Zavoico

Considerable progress has been made during the past year throughout the Russian petroleum industry. Perhaps the most remarkable achievement is the execution of the programs set out by the Central Planning Bureau of the Department of Commerce. These programs have been increased twice during the past operating year, necessitating drilling the richest reserves, instead of developing gradually as originally planned. The fulfillment of the set-out programs during the past few years makes therefore the present five-year plan of considerable importance to the international oil statisticians in approximating actual supply conditions up till 1933. The production of all Russian fields increased by 14,200,000 bbl. as compared with the 1927-1928 operating year, while the next year's program anticipates a further increase of 15,700,000 barrels. It appears therefore that production for 1932-33 will total 187,000,000 bbl., or approximately double that of the operating year just closed. It is also evident that the old fields are counted upon to produce only about 67 per cent. of the total, the new fields, not yet discovered, to furnish the balance of 33 per cent. The Soviet oil leaders therefore are hoping to have new fields discovered and developed by 1932-33. However, as in the past wildcatting

Jan 1, 1930

By Clarence Fenner

THE manufacture of optical glass is a process that demands careful regulation and control at all stages in order that satisfactory results may be obtained. The product, to serve its purpose, must meet stringent requirements, which can be assured only by careful procedure in manufacture. During the greater part of the time that a pot of glass is in the furnace, temperatures should be kept within certain rather narrow limits; a departure on either side is likely to be detrimental to the glass and may result in total loss. If the temperature during melting and fining be low, the melt is likely not to fine properly and the glass will contain quantities of bubbles, or "seed," or it may become milky and unfit for use; too high a temperature, on the other hand, is severe on the pot and may cause it to leak or cast stones, or the increased solution of pot material in the melt may acid to the color of the glass and decrease its transmission. Moreover, variations in the working temperature will mean variations in the amount of selective volatilization and, consequently, variations in optical properties from pot to pot. Furthermore, in the closing stages of furnace treatment, the melt is cooled until a certain degree of stiffness is attained, when the pot is withdrawn. The quality of the glass-its freedom from striae and bubbles-will depend in large measure on whether the temperature to which cooling has been carried is suitable. For each type of glass there is a narrowly restricted range of temperature to which each pot of the given type should be cooled before withdrawal. A quick and reliable method of measuring temperatures is, therefore, of the first importance. In the optical-glass work conducted by the staff of the Geophysical Laboratory during the period of the war, much attention was given to the clatter of determining what methods would meet the requirements. This article will deal with these investigations and with the application of the results to actual practice at various plants. At the. time that the work of the Geophysical Laboratory was begun at the Bausch & Lomb plant, each melting furnace was equipped with

Jan 7, 1919