Search Documents

By Paul L. Horrer

Costly damage by severe wave attack to many engineering structures has illustrated the need for a consideration of the nature of wave action in plans for offshore drilling operations. Using wave data it is possible to answer questions pertaining to engineering problems such as platform elevation, structure orientation, and expected wave forces. For locations where wave records are not available a technique can be used to obtain information about wave characteristics from past meteorological data and near shore submarine topography. Forces exerted on structures by waves may be divided into four parts. A completed study is given in which frequencies of various wave heights and maximum frictional drag forces are computed for a typical offshore drilling site. INTRODUCTION Waves of tremendous proportions accompanying hurricane winds crash against breakwaters and other offshore structures causing untold damages. Wave forces exerted on structures at these times are enormous, as shown by past records of incidents where massive portions of breakwaters have been broken off and moved by waves. On other similar occasions, whole structure; have been unloosed and smashed or floated away. These incidents, which seem almost incredible, serve to illustrate the great amount of energy contained in large waves, and to show that this energy results in powerful forces destructive to offshore installation~ which are not designed sufficiently strong to withstand wave attack. In the past the expected frequencies of waves having various characteristic.% have rarely been considered in the design of structure affected by wave action. As a result, many structures have failed to accomplish the purpose for which they were designed or have collapsed under wave attack. Others have been constructed to withstand greater wave energy than is ever encountered, with resulting waste of material and construction time. In this study an analysis is made of the frequencies of waves having different characteristics which affect the plans for offshore drilling installations. After such an analysis the erection of these structures can proceed with less risk involved and with more efficiency and economy. ENGINEERING ASPECTS In the offshore drilling program wave forces play an extremely important part in design and construction of drilling rigs in shallow water. The design of a platform or other structure from which drilling equipment is operated is critical, becauze any damage to the platform may endanger personnel and result in complete loss of equipment. Since a platform built too close to the water would be battered by breakers, and one built unnecessarily high would involve undue expense, it is necessary to know the most desirable elevation at which the platform should be erected. This is only one of many questions about structural planning which can be answered using existing technique for determining wave characteristics. The purpose of efficient design for the portions of many types of offshore structures which are acted upon by wave forces is the same as that of all designs which deal with frictional forces of a fluid on a solid. For these structures the problem is comparable to that encountered by undersea craft moving through water, except that in the case of a fixed structure the force is produced by the water moving past the model. For off shore sructures which are extremely rigid the frictional forces may be nearly negligible compared with the impact or shock forces imparted by breaking waves. In all case; the better design is that which offers the least resistance to the opposing forces. From a consideration of wave forces, each drilling structure varies in efficiency depending upon the type and amount of superstructure in contact with the waves. For example, round piling and bracing offer less resistance to wave forces than do I-shaped ones. All network superstructure such as cross bracing should be kept to a minimum and at as low an elevation as possible, so that it will not expecience the pressure exerted at the tops of breaking waves. Models of proposed structures can be tested in wave tanks and in the field to ascertain the efficiency of specific designs. Past experience in beach and shoreline engineering has shown that, although changes in the topography of the bottom very near shore do not seem to be occurring, the natural forces involved may be in a delicate balance such that a static state exists. Interruptions of any of these natural forces by erecting offshore structures are likely to cause undesirable effects. Changes in beach profile result partly from sediment being brought into suspension by the orbital motion of waves and partly from the transport of sediment by longshore currents. With the erection of an offshore structure and consequent change in the combined effects of these two forces, unfavorable deposition upon, or erosion of, the bottom at the site may occur. Therefore, combination wave and current studies are essential for the solution of problems involved in the design of most marine structures. TECHNIQUE FOR OBTAINING WAVE INFORMATION In determining the probable effect of wave action on an offshore drilling structure, it is first necessary to know the usual frequencies of certain wave types for the given location. A technique has been developed which provides a means for obtaining information about wave characteristics in the

Jan 1, 1949

By Paul L. Horrer

Costly damage by severe wave attack to many engineering structures has illustrated the need for a consideration of the nature of wave action in plans for offshore drilling operations. Using wave data it is possible to answer questions pertaining to engineering problems such as platform elevation, structure orientation, and expected wave forces. For locations where wave records are not available a technique can be used to obtain information about wave characteristics from past meteorological data and near shore submarine topography. Forces exerted on structures by waves may be divided into four parts. A completed study is given in which frequencies of various wave heights and maximum frictional drag forces are computed for a typical offshore drilling site. INTRODUCTION Waves of tremendous proportions accompanying hurricane winds crash against breakwaters and other offshore structures causing untold damages. Wave forces exerted on structures at these times are enormous, as shown by past records of incidents where massive portions of breakwaters have been broken off and moved by waves. On other similar occasions, whole structure; have been unloosed and smashed or floated away. These incidents, which seem almost incredible, serve to illustrate the great amount of energy contained in large waves, and to show that this energy results in powerful forces destructive to offshore installation~ which are not designed sufficiently strong to withstand wave attack. In the past the expected frequencies of waves having various characteristic.% have rarely been considered in the design of structure affected by wave action. As a result, many structures have failed to accomplish the purpose for which they were designed or have collapsed under wave attack. Others have been constructed to withstand greater wave energy than is ever encountered, with resulting waste of material and construction time. In this study an analysis is made of the frequencies of waves having different characteristics which affect the plans for offshore drilling installations. After such an analysis the erection of these structures can proceed with less risk involved and with more efficiency and economy. ENGINEERING ASPECTS In the offshore drilling program wave forces play an extremely important part in design and construction of drilling rigs in shallow water. The design of a platform or other structure from which drilling equipment is operated is critical, becauze any damage to the platform may endanger personnel and result in complete loss of equipment. Since a platform built too close to the water would be battered by breakers, and one built unnecessarily high would involve undue expense, it is necessary to know the most desirable elevation at which the platform should be erected. This is only one of many questions about structural planning which can be answered using existing technique for determining wave characteristics. The purpose of efficient design for the portions of many types of offshore structures which are acted upon by wave forces is the same as that of all designs which deal with frictional forces of a fluid on a solid. For these structures the problem is comparable to that encountered by undersea craft moving through water, except that in the case of a fixed structure the force is produced by the water moving past the model. For off shore sructures which are extremely rigid the frictional forces may be nearly negligible compared with the impact or shock forces imparted by breaking waves. In all case; the better design is that which offers the least resistance to the opposing forces. From a consideration of wave forces, each drilling structure varies in efficiency depending upon the type and amount of superstructure in contact with the waves. For example, round piling and bracing offer less resistance to wave forces than do I-shaped ones. All network superstructure such as cross bracing should be kept to a minimum and at as low an elevation as possible, so that it will not expecience the pressure exerted at the tops of breaking waves. Models of proposed structures can be tested in wave tanks and in the field to ascertain the efficiency of specific designs. Past experience in beach and shoreline engineering has shown that, although changes in the topography of the bottom very near shore do not seem to be occurring, the natural forces involved may be in a delicate balance such that a static state exists. Interruptions of any of these natural forces by erecting offshore structures are likely to cause undesirable effects. Changes in beach profile result partly from sediment being brought into suspension by the orbital motion of waves and partly from the transport of sediment by longshore currents. With the erection of an offshore structure and consequent change in the combined effects of these two forces, unfavorable deposition upon, or erosion of, the bottom at the site may occur. Therefore, combination wave and current studies are essential for the solution of problems involved in the design of most marine structures. TECHNIQUE FOR OBTAINING WAVE INFORMATION In determining the probable effect of wave action on an offshore drilling structure, it is first necessary to know the usual frequencies of certain wave types for the given location. A technique has been developed which provides a means for obtaining information about wave characteristics in the

Jan 1, 1949

By George L. Atwood, William Brown

Phosphate ore is being mined at Monsanto Co.'s Henry mine, near Soda Springs, Idaho, for the company's three furnace elemental phosphorus plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. In stripping and mining, D-9 crawler tractors are utilized to rip and push-load rubber-tired scrapers. The equipment consists of six D-9G crawler tractors, four Caterpillar 657B scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12- month basis, two shifts per day, whereas mining is mainly in the summer months on a one-shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1 million tons of phosphate rock and 2.5-3 million cu yd of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor which owns, operates and maintains all equipment used. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis.

Jan 8, 1972

By Robert E. Delavault, Harry V. Warren

Circumstances determine whether it is better to make analyses in the field or in a permanent laboratory. The rubeanic acid test described in this article has been designed primarily for field use: it is simple and virtually foolproof, and it requires a minimum of field kit.* It is sensitive, easily detecting 4 ppm of readily extractable copper in a soil. This is by no means a quantitative test, but it is accurate enough to provide a valuable indicator of copper anomalous areas for both prospectors and field geologists. The easiest method for detecting metal deposits that do not produce visible float or stains is to make a simple chemical test for the metal in overlying soil, or in the silt of a stream that may have picked up metal farther upstream.

Jan 11, 1958

By Edward W. Mehal

This paper presents a review of the technologies which have been used in the application of III-V compound semiconductors to integrated circuits and arrays. These materials have properties which make them useful for various devices such as: light emitters, sensors, microwave sources, and microwave diodes. Technologies for incorporating these devices into integrated circuits have been reported and processes developed for fabricating planar devices using selective epitaxial deposition or selective diffusions. Isolation methods utilizing semi-insulating GaAs, oxide isolation, and ceramic insulation have also been reported. These techniques, and the devices and circuits produced or proposed are discussed. AFTER the invention of the silicon-integrated circuit, methods for utilizing compound semiconductors for integrated circuit applications were proposed. The scope of applications was potentially much broader because of the range of properties available from these materials. There also was the opportunity of coupling these properties with germanium and silicon devices to realize functions and circuits which could not be produced with silicon monolithic circuits. Table I exemplifies the range of electrical properties available in III-V compound semiconductor materials which are currently being widely used. A wide range of sensor and emitter applications result from the range of band gap. The band structure of GaAs and GaAsxP1-x permits their use as microwave oscillator source, and the high electron mobilities further facilitate their utility in microwave devices. The concept of "integrated functions"1 results from the availability of these materials and methods for utilizing their special properties. Heteroepitaxial growth allows the fabrication of a monolithic block of these materials. Semi-insulating GaAs permits the attainment of electrical isolation between components in a monolithic block without resorting to p-n junction biasing or oxide isolation methods. An "integrated function" is a unit which can perform a system or subsystem role and perform a number of electromagnetic functions. These functions could include sensor or input transducer, signal processing, interconnections, and control or output function. Two examples which demonstrate this concept are an optoelectric processor and a microwave receiver front end. The optoelectronic processor, Fig. 1(a), would consist of a light sensor, signal processor, and output emitter. The sensor could be InSb or InAs which would be IR-sensitive. The signal from this sensor would then be amplified and transmitted to the light emitter. The amplifier could utilize GaAs bipolar or field effect transistors. A Gap emitter would then produce visible radiation. The microwave receiver front end, Fig. l(b), would consist of a local oscillator section and a mixer section. A signal input from an antenna is mixed with the signal from the local oscillator. The local oscillator signal is produced by a Gunn oscillator. The single-ended mixer utilizes one Schottky barrier mixer diode. The IF signal would then be amplified further and suitably displayed. A further extension of the capability of utilizing the

Jan 1, 1969

By Malcolm J. McPherson

INTRODUCTION The use of computers to assist the mine ventilation engineer began to grow in the early 1950s when electrical analogue devices were developed for the analysis of mine airflow systems in Europe and the United States (l,2,3). The need for quantitative planning of airflows in mines had become pressing and analogue computers fulfilled a useful purpose for over a decade. From about 1964 onwards, digital computer programs for mine ventilation network analysis became available (4,5) and, superseding the analogues, spread rapidly throughout the major mining countries. The successful implementations of such programs resulted in further research being directed towards the development of simulation programs to model the quality as well as the quantity of air flowing through underground workings. It is no understatement that digital computers have revolutionised environmental planning techniques in modern mining industries. This paper discusses the complex interaction of natural and mining factors which governs environmental hazards in underground mines and further indicates some of the simulation techniques which have entered practical usage or are at an advanced stage of development. THE PROBLEM OF ANALYSING THE MINE ENVIRONMENT The traditional methods of approaching environmental problems underground were based largely on empirical or intuitive techniques. The reason for this lay in the intricate relationships which exist between the many variables that influence the mine environment - and which limit the use of purely analytical methods to the simplest of cases. In order to illustrate the need for simulation techniques, Table 1 shows the three most widespread mine environmental hazards

Jan 1, 1977

By John C. Nigro

The Bureau of Mines is investigating the use of pulverized coal as a fuel for iron ore pelletizing to determine its effectiveness as a substitute for natural gas and oil. Experimental data illustrates the application of both a gun-type suspension burner and a cyclonic-type slagging burner to a grate-kiln pelletizing unit. In addition, experimentation with a cyclonic fired external combustion chamber for possible adaptation to a shaft or straight grate pelletizing furnace is discussed. The tests were conducted in the Bureau of Mines Twin Cities Metallurgy Research Center's pilot plant with high rank bituminous coals from Kentucky and Colorado and low rank subbituminous coals and lignites from Montana, Wyoming and North Dakota. Although combustion was excellent with the suspension burner, the low ash fusibility temperature coals and lignites caused some kiln ringing and accretion buildup in the grate kiln transfer section which were not encountered when firing with the high ash fusibility temperature Kentucky coal. Pellet contamination by coal ash was not deemed substantial. Problems with the cyclonic burner and external refractory combustion chamber centered around (a) maintaining complete combustion of the coal within the burner, (b) molten slag attack on the lower refractory chamber resulting in erosion of the lining and increased slag viscosities, and (c) freeze-up of the slag tap hole.

Jan 1, 1977

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By Allan D. Taylor, Robert S. Shoemaker

Adopting as a principle the phrase "the mill of yesterday should not be built with the high cost money of today," the authors have designed a hypothetical concentrator which could be built for a typical southwestern United States (or other similar area) copper ore. Many of the design features could also be used for other ores in other climates. Functional design, large equipment, and outdoor type of construction have been combined in a concentrator (which includes all ancilliary facilities such as truck and maintenance shops, offices, warehouse, nominal tailings disposal, and water supply) which could be built today for substantially less than the cost of comparable but conventional plants.

Jan 1, 1973

By Sam Tour

SOME years ago, the writer described heat checks or thermal. cracks that occur in die-casting dies.1 The life of dies was considered in relation to the casting temperature, the material used for the die, and the heat to be absorbed by the die per unit volume of casting made. The mech-anism of the action that results in thermal failure of dies was described. In the present paper the writer proposes to describe some additional observations in regard to heat checking, make one or two suggestions as to the method or methods for further attack of the problem, and give the results obtained on some work carried out along these lines.

Jan 1, 1934

Discussion of the paper of WALTHER MATHESIUS, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 539 to 555. JOSEPH W. RICHARDS, So. Bethlehem, Pa.-This paper answers. partly the difficult questions which have come up as to why it is not economical to use higher blast temperatures in the smelting of Mesaba ores, such as the high temperatures used in European practices, and the answer is very plain that the ores will not stand the higher temperature. But the paper does not go into detail as to what special difficulties were found with the higher temperature of blast, and I would ask the author to kindly specify them. W. A. FORBES, New York, N. Y.-A large part of the troubles that furnace men experienced in using high-blast heats in smelting Mesaba ores in the early days of using Mesaba ores, was clue to the attempt to use these soft ores on furnaces having the same lines as the furnaces used in smelting the hard Old Range ores. As the result of observation and study, the dimensions of the lower part of the blast furnaces have been changed and the difficulties of the blast-furnace men in operating with a large percentage of Mesaba ore and high-blast temperatures have been largely overcome. The changes I refer to in particular are: (1) steepening the angle of the bosh; (2), decreasing the height of the bosh; (3) increasing the diameter of the hearth. JOSEPH W. RICHARDS.-Mr. Forbes's answer is quite satisfactory, and the moral which it points is that when the furnace is run with a higher temperature in the smelting zone, the furnace lines which were adapted for the lower temperatures are not necessarily those best suited for the higher hearth temperatures. If. enriched blast were used in a furnace, and higher temperatures run, it would be found necessary to further modify the lines of the furnace to meet the new conditions and to get the maximum output with economy. J. E. JOHNSON, JR., New York, N. Y.-It seems to me this is one of the few papers which could well have been a little longer. The data which Mr. Mathesius has given us, I think should be considered in connection with the paper which Mr. Brassert read before the American Iron and Steel Institute last spring, in which he described how they had obtained remarkable results with furnaces with steep but very short boshes; the angles have been raised to 80°, and the boshes made so short that they no longer appear as a conspicuous part of the shape of the furnace.

Jan 5, 1915

By H. H. Waller, D. L. Monroe, D. P. R. Smyth

ORIGINALLY slusher drift development was conventional, advancing the drift full 10x13-ft size at 6 ft per round. This proved dangerous and costly because the weak fractured rock of the orebody cannot be left raw for any length of time without its reacting with air to cause spalling. With this method of drift development ground conditions were worsened by many blasts and the length of time it was necessary for the drift to remain open. The problem was practically solved by driving 5x7-ft pilot drifts, then enlarging to 10x13-ft raw size by slashing with 50 to 60-ft diamond drill holes. Calculated explosive charges are used to avoid wall and roof shattering. Still more recently jacklegs and sectional steel replaced the diamond drills, resulting in the same work for less than half the cost, see Figs. 1 and 2. Crosscuts at right angles to the main haulage drifts, which cross through the center of the ore-body, divide the ore into 200-ft blocks. Eight slusher drifts on 50-ft centers draw from one block. The slusher floor is 11 ft above the rail, inclined at 1 pct grade, and the top is 18 ft below the undercut. The finished slusher drift is 102.5 or 120 ft long, depending on whether it is north or south of the crosscut. Drawpoints are staggered on each side at 17.5-ft centers. The completed drift is concreted and has an inclined ramp and a vent at the back. When crosscuts and gangways have been excavated and concreted and slusher stations installed, slusher drift development is carried out in 10 clear-cut stages: 1—Pilot drift is driven full length, 5x7 ft. 2—Station is excavated at half-way point in pilot drift. 3—Pilot drift is enlarged to slusher drift size by drilling. 4—Lower part of slash is blasted and mucked for floor concrete. 5—Floor is poured. 6—Inside upper half of slusher drift is blasted, mucked, and concreted. 7—Outside upper half of slusher drift is blasted, mucked, and concreted. 8—Drawpoints are excavated. 9—Drawpoints are concreted. 10—Concrete ramp and sheave protection recess are constructed at back end of slusher drift. A 5x7-ft pilot drift is driven full length on the center line of the proposed slusher drift using a jackleg and detachable bits on 7/8-in. hexagon steel. A 10-hp air-driven slusher and 36-in. scraper pull muck directly into cars in the main haulage crosscut, see Fig. 2. Operations are on a three-shift basis. One man mucks the previous round, drills, and blasts his round in a shift. Average advance is 5 ft per shift. When the pilot drift is completed, 7 ft of drift in the center section is enlarged to full raw slusher drift size of 10x13 ft, for the set-up to drill long slash holes. The pilot drift is slashed to full raw size from this station with jacklegs and tungsten carbide chisel bits on 7/8-in. sectional steel. Crews line the holes without trouble, working from controls established by the engineers, and the pattern of holes for the slash is arranged to give the least shattering effect

Jan 1, 1955

By Neil H. Cole

Cost and price inflation and financial gearing through loans are characteristic of modern resources projects. Conventional discounted cash flow and 1P.R analyses, in real terms, and without financing, have inadequacies which can yield misleading results. The degree of improvement in value for project equity owners is limited to the value of the additional tax benefit accorded through the financing instrument used. Debt financing may be low in price and value, but its priority means that the equity owners assume a higher risk, thereby increasing the cost, or price, of their capital. The cost of equity capital, or investment hurdle rate, is related to the Capital Asset Pricing Model. Distortions do occur, with inflation, due to depreciation effects, which can cause the adoption of misleading project rate of return or hurdle rate criteria. For investment decisions, the greatest accuracy possible in forecasting is essential, especially for inflation rates,

Jan 1, 1985

By Arthur F. Johnson

Plant sites for the light metal industry must be located where ample low cost power is available. In the first half of the century hydroelectric development was the only source of this power-now the best sites have been exploited and those remaining do not promise enough water to permit year-round capacity power plant operation. In searching for economic plant sites engineers have concentrated on locations with vast water power potential. Olin Mathieson Chemical Corp. has been studying the economics of developing water power to make aluminum. However natural gas, lignite, and even atomic energy have also been considered as possible power sources for aluminum production. Economic studies have given consideration not merely to investment and production costs, but to total costs of delivering fabricated products to the market center of the U. S. When delivered costs are considered and when full account is taken of the newest techniques of mining bituminous coal and utilizing it to make electric power, one arrives at the inescapable conclusion that coal has emerged as the economic answer to American aluminum production.

Jan 4, 1955

By Lillian Erskine

WHILE brass and other copper alloys have long been listed as offering health hazards to their workers, it is questionable if the metals involved are alone responsible for the trades' records of morbidity. The entire science of foundry sanitation is the product of the past two decades; and the best standards now operative would have been regarded as little short of revolutionary prior to 1910. The special handicap to the conservation of the health of the brass founder's employees has been the fact that, unlike the iron founder, his business could be profitably carried on in almost any small and unsanitary quarters. As a result, writers on occupational disease have accepted brass chills or brass founders' ague as an inevitable feature of the trade; and respiratory disabilities, as well as phthisis and disturbances of the nervous system, are also included as prevalent among those employed. While there can be no question as to the basic accuracy of past investigations, there is every reason to doubt the necessity for an undue percentage of ill health among brass molders and casters who are safeguarded by scientific ventilating standards and by improving personal habits of sobriety. There is, however, need for a campaign of education as to the most approved practices and equipment whereby the employer may safeguard the health of his workers, and thereby reduce his labor turnover and increase his productive efficiency. Broadly speaking, copper, tin, and aluminum carry negligible health hazards. The toxic qualities of lead, however, are a menace; especially if scrap lead is recovered or bought for foundry processes. The rapid volatilization of zinc renders its fumes and flocculent condensation the chief problems in conserving the health of the brass worker. The frequent presence in the foundry air of traces of arsenic compounds, lead

Jan 2, 1919

By N. De Nevers

A calculation method has been developed for carbonated water flooding. This method takes into account the effects of oil viscosity reduction and oil swelling, due to carbon dioxide transferred to the reservoir oil from the carbonated flood water. It shows the effect of changes in carbonation pressure and carbonated water slug size. The method is based on a Buckley-Leverett-type linear flow model. The mathematical approach is similar to that developed by Welge, et al, for enriched gas drives. However, it contains a very important advance over the previous papers in its solution to the problem of injection of a "slug" of carbonated water rather than continuous injection of fluid of constant composition. The method also shows the chromatographic nature of the transport of Co 2 in a carbonated water flood. Sample calculations indicate that viscosity reduction is the most important source of incremental oil recovery. Swelling contributes to a lesser extent. Raising the carbonation pressure increases recovery, but this effect diminishes as pressure is increased. increasing the slug size also increases recovery, but again this effect diminishes as slug size is increased. INTRODUCTION In recent years there has been considerable interest in carbonated water flooding as a secondary recovery method. Several carbonated waterflood field tests are now in progress.1'3 Yet there is no published method for predicting the results of a carbonated water flood. This paper presents a method for predicting the oil recovery for ; carbonated water flood. In a carbonated water flood. a carbonated water slug is injected into the reservoir. Then this slug is driven forward by injecting plain water behind it. The field operator must choose the carbonated water slug size and the CO2:water ratio in the slug. The calculation method presented here shows the effects of both slug size and CO2:water ratio on oil recovery. The calculation assumes that the addition of carbon dioxide to flood water increases the oil recovery by two mechanisms: 1. Carbon dioxide transfers from the flood water to the oil, thereby reducing the viscosity of the oil. At the lower viscosity, the oil flows more readily and is more easily swept out by flood water. 2. The carbon dioxide which transfers to the oil phase causes the oil phase to swell. Assume that the residual oil saturation (volume per cent of pore space) is the same whether the oil is carbonated or not. Then the same volume will contain less stock tank oil if it is carbonated, due to oil swelling. The plain water driving the carbonated water slug forward will strip the CO2 out of this residual oil., causing this oil to shrink. This swelling-followed-by-shrinking leaves behind a lower residual oil saturation than would have been left behind by a plain water flood. Since some oils swell to almost twice their original volume at reasonable CO2 pressures, this effect may be large. Two additional benefits sometimes claimed for carbonated water flooding are: 1. Adding CO2 to flood water greatly increases the water injectivity in some cases.1 (Injectivity = BPD of water injected/ft of sand x differential bottom-hole pressure, psi.) CO2 forms a weak acid in water; injecting carbonated water is, therefore, somewhat like acid treating. If a formation responds to acid treating, it will probably have a higher injectivity for carbonated water than for plain water. Although the increased injectivity increases the profitability of a carbonated water flood over a plain water flood, it does not change the production curve based on total fluid injected. Therefore, the method presented here does not show any effect of increased injectivity. 2. It is claimed in one patent4 that carbon dioxide will react with some constituents of the oil to form detergents. These detergents are expected to increase the oil recovery. There is little data available to support this idea. The calculation method presented here takes no credit for extra oil recovery due to the formation of any such detergents.

Jan 1, 1965

By A. B. Kinzel

THE demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low tempera-tures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selec-tion of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low tempera-tures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120° C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By R. C. Hyslop

THE object of this experiment was to obtain a usable set of field curves for determining the susceptibility of rocks with the vertical magnetometer. The need often arises for determining the susceptibility of rocks in the field in order to interpret magnetic anomalies obtained. This is particularly true when diamond drilling has been done and the relation to the surface rocks of the samples taken is desired. Many methods of measuring rock susceptibility have been developed, but in general they require careful shaping of the sample or pulverizing it in addition to delicate laboratory measuring instruments designed for the purpose. The requirements for a practical method for the determination of susceptibilities are as follows: I. There should be as little alteration as possible of the specimen. 2. A minimum of time should be required in the preparation of the specimen and the calibration of the equipment. 3. The equipment used should be portable. 4. An accuracy within the limits of the survey at hand should be obtainable. 5. A means of measuring the remnant magnetism should be available. LABORATORY PROCEDURE With these ideas in mind, the problem was approached in the manner in which Koenigsberger1 developed his method using the principle of the electrical theory of images of Lord Kelvin and applying it to the magnetic case. This solution of the problem states that the apparent change [ ] in the magnetic field intensity due to the proximity of a specimen is given by: [ ] Where k is the susceptibility of the specimen, m the strength of the pole of the needle, and a its distance from the surface of the specimen, as shown in Fig. I.2 This relation is true only for an infinite body and corrections are necessary for a finite body. Koenigsberger used in his work a variometer of special design. He suggested that a Schmidt vertical balance or horizontal magnetometer, as well as some other instrument, might be used. The Colorado School of Mines horizontal torsion magnetometer operates on this principle. In the

Jan 1, 1941

By Kerstin Malmqvist

A prospecting project for deep-seated sulphide ore bodies will be expensive and means a considerable economic risk. The high costs depend on the demand for extensive drilling. It is therefore important to find effective methods to estimate the outcome of different prospecting strategies. The results from a preliminary study of the possibility of using mathematical methods for this purpose are presented. We have found that mathematical methods, especially simulation technique, might be an important tool in such exploration work. A mathematical model of an ore field and of a drilling procedure has been constructed. A set of parameters describes the geometry, the size distribution and the intensity of ore bodies. Another set describes the geometry and the intensity of drill holes. Some preliminary results are given of Monte-Carlo simulations and probability calculations.

Jan 1, 1977

By M. L. White, J. L. Shafer, C. L. Caenepeel

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper.

Jan 2, 1979