Search Documents

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

By Rudolf Kudlich

The problem of eliminating the hazards of hoisting in mines has been with us since the industry passed its earliest stages, when coal and ore could be won from surface working and tunnels. At first, safety devices were introduced as means of decreasing the amount of labor necessary to produce the mineral, or to increase the amount that could be obtained from a certain opening. For example, crude ladders replaced winding footpaths or steps cut into the walls of the pit or shaft, decreasing the distance it was necessary to carry the product to the surface and eliminating, to some extent, the hazard introduced by the precarious footing afforded by such paths and steps. Latcr, instead of being carried from the pit on the backs of men, the product was hoisted in buckets or baskets on a rope passing over a pulley or around a windlass. Thus the capacity of the pit was considerably increased, and the hazard due to making many trips up and down the shaft was eliminated. From such beginnings accident prevention in mine hoisting advanced with the importance of the industry, until at present hoisting compares favorably with other branches of the mining industry with reference to safe practices. As in the other branches, this progress has been accomplished along two general lines—by legislation, rules, and education, and by the installation of safety devices. Though due credit must be given the former, it is not so satisfactory as the latter. Legislation, to be effective, requires a policing and inspection system to guarantee enforcement, such as we cannot hope to inaugurate. Rules may be satisfactory so long as the employer controls the labor market, and dismissal or some other form of discipline is an effective means of insuring obedience to the rules; but where labor demand is in excess of the supply, or where labor organizations are in control, such measures are not effective. An educational campaign will draw attention to hazards and may awaken a desire to avoid accidents by exercising the proper care. It is necessary, therefore, to place our reliance mainly on mechanical devices to prevent accidents, and to depend as little as possible on laws,

Jan 1, 1923

THE second award of the Saunders Gold Medal for "distinguished achievement in mining," of which the first was awarded last year to the late D. W. Brunton, has been made to Herbert Hoover. The main events of Mr. Hoover's life are so familiar to all through the numerous journal articles about him and his work, and the interesting biography written by Vernon Kellogg, that no attempt will be made here to touch on anything other than his achievements as a professional mining engineer, for which the award was made. He graduated in mining from Leland Stanford, Jr., University in 1895, but had served as an assistant to Dr. Branner on the Arkansas Geological Survey in 1893 and had also worked two sum-mers as an assistant to H. W. Turner and Waldemar Lind-gren on U. S. Geological Sur-vey work in the Sierra Nevada around Lake Tahoe, and on the American River. Immediately after graduation he got "a job" underground at Grass Valley, and soon rose to be night shift-boss. He then secured employment with the late Louis Janin and made such a good record as office and field assistant that he was soon placed in charge of a small mine at Carlisle, N. M. In 1897, Mr. Janin recom-mended him to Bewick, More-ing & Co., who were looking for an examining engineer for their staff in Australia. Two years were spent in hard work there which was done so creditably that his princi-pals held him and his judg-ment in the highest regard, and he came to the head of their local organization. Among the properties which he acquired for them was the Sons of Gwalia.

Jan 2, 1928

By Adolf Gurlt

It has long been known that minute quantities of foreign substances, when alloyed with steel, are capable of materially altering its physical properties. Thus, half a century ago, Faraday and Stodart, in England, discovered in the famous Indian steel, known as " wootz," small quantities of aluminum, from 0.0728 to 0.693 per cent., and attributed its extraordinarily good quality to the presence of such minute quantities of that metal. Since aluminum is now produced by electrolytic means on a large scale and at low cost, its addition to cast-steel has been frequently recommended of late. Chromium was alloyed with steel fifty years ago by the celebrated French metallurgist, Berthier, of Paris, and has recently been successfully applied to the same purpose by Holtzer, of Terre-Noire. In 1860 titanium was alloyed with crucible steel by Robert Mushet, of Coleford, the alloy containing up to 0.50 per cent. of titanium, which was extracted from Norwegian ilmenite. The titanium-steel was much vaunted by him for its excellent qualities. Rhodium, a very rare metal of the platinum series, was maintained by Berthier to improve steel materially in strength and hardness. Manganese has always been held by Sheffield steel-melters to provide steel with excellent qualities, and this influence was quite recently investigated by H. M. Howe and L. Campredon. Nickel was tried as an addition by Berthier, not to speak of gold, silver and platinum ; and nickel-steel has recently been brought into prominence by J. Riley and others, who recommend it for its great strength and toughness, particularly as material for armor-plates.

Jan 1, 1894

By V. Steve Reed, Ed L. Reed

The in situ leach mining process generates a waste stream that is high in sulfates, total dissolved solids, and radium 226. During the mining phase, the volume of the waste stream is relatively low and consists primarily of the bleed stream. During the restoration phase, larger volumes of waste water are generated. These waste streams require environrnentally sound disposal. The low net evaporation rate in the Coastal Bend area precludes pond evaporation as a feasible disposal alternative. Reverse osmosis is a practical method of reducing the volume of the waste water handled, but the concentrated waste stream from the reverse osmosis unit must be disposed properly. Deep well injection into highly saline reservoirs is considered a sound method of disposing of the liquid waste generated by in situ mining in the Gulf Coast uranium district. Thirteen injection wells have been permitted to serve the disposal needs of the leach mining industry in Texas. Of these 13, 11 have actually been drilled. Seven applications are pending. The injection zones for the permitted wells range from depths of 3050 to 6200 feet. Pressure limitations imposed on these wells range from 500 psi to 1350 psi. The following criteria are used to determine the desirability of a disposal well site: 1. A minimal number of nearby, improperly plugged borings which penetrate the disposal zone; 2. Minimal crustal disturbance; 3. Sufficient salinity of the water contained in the disposal zone; 4. Protection of oil and gas producing zones; and 5. Sand of sufficient permeability and areal extent to handle the desired volume without fracturing the reservoir. 1. Improperly plugged borings: During the early part of the century, oil wells, gas wells and test holes were drilled using cable tool equipment, often with a minimum amount of surface casing. Production casing, when it was set, was often partly removed when the holes were abandoned. Thus, wells drilled prior to 1940 frequently have less than 100 feet of surface casing and either no production casing or the upper part of the production casing removed. Additionally, these holes are often plugged only with mud. The close proximity of these holes to an injection well location are a concern in that they can provide an avenue for injection-depth fluids to migrate up the bore hole and jeopardize shallower fresh water reservoirs. Usually, where there are more than 6 or 8 poorly plugged borings in a 2 1/2 mile radius of the well site, it is preferable to examine deeper zones for disposal well potential. The deeper zones are especially attractive where the borings are not in a cluster, which renders monitoring more difficult. Often, even the deeper disposal zones are penetrated by a few improperly plugged borings. When this condition arises, the potential for leakage through the borings can be addressed in the following ways. a. Demonstration that the static head in the boring is higher than the anticipated increase in bottom hole pressure generated at the boring by the disposal well. A 100 psi differential between these two pressures is recommended. The calculated increased pressure at a boring caused by injection should be refined using annual bottom hole pressure measurements in the disposal well. Figure 1 illustrates an injection pressure map which can be overlain on the oil well map to determine the anticipated increase in pressure expected at each oil, gas or abandoned hole. b. Shallow ground water monitoring. A shallow monitor well is drilled next to the boring and both pressure and quality measurements are made periodically in the shallow well. c. Disposal zone monitoring. Recently there has been a tendency for regulators to require disposal depth monitor wells instead of shallow well monitoring. We consider disposal depth monitoring to be a less effective method of monitoring because it provides only indirect evidence of potential problems. Assumptions have to be made for the unplugged borings, such as mud weight, that are not addressed by the disposal zone monitoring program. There is little improvement with this system to that discussed in "a" above. A shallow zone monitoring program, however, yields direct evidence of a developing problem with an unplugged boring. Leakage by the boring will be detected quickly by an abnormal increase in pressure in the shallow well. Quality monitoring will detect upward migration of poor quality fluids. The pressure data provide an early warning of impending leakage; the quality monitoring will detect actual fluid migration.

Jan 1, 1980

By W. L. Chu

It was observed that chromized coatings on low carbon steel could be embrittled by cooling slowly through the 475°C range. A higher chromium coating was more susceptible to embrittlement than a lower chromium coating. Coating structure and composition could be correlated with the chromizing process and prior carbon content of the steel. IT was recently observed that during the fabrication of rectangular tubings made with chromized thin gage 1010 steel, a high percentage of these parts were fractured readily in a brittle manner under the light impact-forming load employed. Ensuing investigation indicated the cause for such brittle failures to be the so-called 475°C embrittlement of the chromized coatings. The experimental work and results are briefly reported. Rectangular tube sections of normalized AISI C1010 steel, which had a cross-section of 0.5x1.5 in. and a wall thickness of 0.030 in., were chromized to yield coatings having several ranges of thickness, varying from 0.0005 to 0.002 in. Essentially, the chromizing process is similar to that described by Samuel and Lockington,' which consists of heating the parts in a sealed container at about 955°C for 4 hr in intimate contact with a chromizing mixture* samples in a hydraulic press, and the other employed a simple beam bending test of the flat sides of the tubing walls. Neither, however, was able to differentiate the relative brittleness of samples known to include both the brittle and tough types, since the impact-brittle samples were found to deform readily in a manner similar to the tough ones. Both the tough and brittle samples were studied by reflection microscopy. Observation showed that the microstructures of the steel cores were similar in content and distribution of inclusions as well as in the ferritic grain size. Results of Filar micrometer measurements showed that coating thicknesses+ of the brittle samples averaged 0.0007 in., whereas those of the tough samples averaged 0.0016 in. The micrographs of Fig. 2 illustrate the structural differences between coatings of both types of samples. By dissolving the steel cores in nitric acid, coatings of both the brittle and tough samples were isolated. Simple bending tests showed that coatings of the brittle samples cracked readily at about 90" bend, whereas those of the tough samples could be bent nearly 180° without cracking. The coatings as well as the steel cores were analyzed for carbon and

Jan 1, 1956

The National Labor Board, on June 25, ended its activities preparatory to final, dissolution by the President. No new cases will be heard nor new applications received. Controversies, jointly submitted, that could not be concluded prior to June 30, were assigned to the joint chairmen or a section of the board for disposition. The conclusion of the board's activities marks the passing of. one of the governmental agencies created during the war to further production of war materials. The board was organized under a Presidential proclamation with former President Taft and Frank P. Walsh of Kansas City as joint Chairmen, and with five members representing labor, five employers' representatives, and two members acting for the public. Mr. Walsh resigned soon after the signing of the armistice and was succeeded by Basil M. Manly of Washington. During the year that ended May 31, the hoard received 1245 cases, made awards in 462 cases, dismissed 391 for various cases, referred 315 to specified agencies, and suspended one case. Fifty-three cases remained on the docket because the hoard could not agree, and 23 cases were pending.

Jan 8, 1919

By George F. Weaton, Eugene P. Pfleider

13.4-1. History. During the past ten years the mining and production of iron ores has been through a revolution. From 1939 through 1948, which included World War II, 561,000,000 tons of iron ore was mined and shipped from Minnesota's Mesabi Range to the blast furnaces of the United States for the production of iron and steel products (20, 28, 29). The iron mining industry, anticipating the exhaustion of this highly productive source of raw material, instigated a worldwide search for new sources of iron ores. This search was highly successful, both as to quantity and quality. Venezuela (38), Canada (17, 28, 42), Peru (19, 23, 50, 52, 54, 56) Chile, (1, 66, 75), Brazil, and Liberia were among the countries where enormous deposits of high quality iron ores were discovered. The exploitation of these deposits took away the monopoly held by the Lake Superior region for so many years and created a highly competitive market for high quality natural iron ores. 13.4-2. Exploration and Development Practices. SPECIFIC TO IRON MIN- ING. American industries are motivated to continue exploration because new ore discoveries often lead to an improved competitive position with respect to raw material supply. Exploration techniques have advanced rapidly in recent years, to a degree that potentially important iron ore reserves, stratigically located, may now be detectable by application of a combination of refined and diversified geophysical exploration methods. Since the days of the dip needle, iron ore people have placed greatest reliance on the magnetometer. Its successive stages of development progressed from the balance and the torsion type to the fluxgate, and then to the "sophisticated" magnetometers-conceived and developed in th field of atomic physics. By far the greatest advancement in magnetometer prospecting was made when the self-orienting fluxgate magnetometer took to the air. This was not a new development, but it was a breakthrough in reconnaissance investi-

Jan 1, 1968

By S. F. Shaw

MINING conditions in Mexico during the current year have been most unfavorable, synchronizing with conditions in the United States, but the outlook for the near future is improving. The chief difficulties met with are because of the following conditions: severe drop in prices of metals; high smelting rates; high prices of supplies; inadequate means of transportation; low efficiency of labor. In comparison with pre-war prices for metals it cannot be said that prices are low, particularly for silver, which recently has gone to a level that would have been considered exceedingly good in 1912. But conditions have changed so greatly that only the most favorably situated properties can operate without loss.

Jan 1, 1921

By AIME AIME

THE following is the discussion of a paper, with the same title, by N. L. Alison, which appeared in our February issue: E. F. Tillson commented that while the fundamentals are well presented it would have been of interest to him to have had the author add some of his own experiences with fan installations. A. W. Hesse remarked concerning the use of the forward curved blade fan on the surface at a metal mine which has, ordinarily, but few airways, that the farther they are driven, the higher the resistance rises, and less air will be delivered, as the water gage will remain constant with a consequent loss in quantity. D. Harrington added that the metal mines do not or¬dinarily install fans until the mine is well developed, so changes are relatively slower after fan installation than at a coal mine.

Jan 1, 1930

By Henry A. Ley

Oklahoma produced about 40,000,000 bbl. less crude oil in 1930 than it did in 1929, but developed the largest initial production from current well completions ever recorded in its history. The output of this year would have exceeded all previous years had it not been for state-wide production curtailment. The record initial production of 5,911,982 bbl. from new oil wells completed during the year is accounted for entirely by the rapid development of the Oklahoma City field. Completions declined to the lowest levels since 1909, as a result of a marked reduction in number of dry holes incident to reduced wildcat exploration. Leasing was most active in western and northern counties of the state west of Oklahoma City, but on a much smaller scale than in the preceding year. Geological and geophysical surveys were likewise most active in this western territory. The urge to deeper objectives resulted in the discovery of oil on the Cement fold. Changing economic conditions have created a distress situation among the marginal operators in northeastern localities of the state. Elsewhere in the state production records and successful exploitation of new supplies have been eclipsed by a new social concept of the industry in accord with natural economic developments. Many of the producers of crude oil have organized for a voluntary stabilization of the industry by regulating the output of wells. To enforce their measures these operators have sought for and secured the support of the state. Consequently, the current position of the crude-oil producer is not unlike that of the natural-gas producer—withdrawal of supplies in accordance with market needs. And while the industry as a whole is artificially stabilized by these measures individual operators and some of the integrated concerns suffer hardships. Oil Developments and Production The early operations in Oklahoma were confined to northeastern and eastern localities, beginning in 1885. The first commercial oil wells were completed in 1894, near Chelsea in Craig County, from Cherokee sands in the lower portion of the Pennsylvanian section. Scattered

Jan 1, 1931

By H. F. JR. Miller

(Butte Meeting, August, 1913.) THE major cause of the deterioration of the open-hearth furnace as its length of service increases, is the melting down, or rather the slagging, of the checker-brick, together with the deposition of dirt in the form of iron oxide, etc., which helps to close the openings, as well as to slag the brick by chemical action. Any construction that will do away with the necessity of having the waste gases come down through the checkers will eliminate the main reason for their deterioration. There are some other well-defined reasons which are subordinate to the main one given above. Some of the defects of the present type of regenerator chambers are as follows: 1. The checkers cannot be cleaned while the furnace is in operation, nor can they be cleaned at the end of the run without taking out all of the checker-brick. This causes high costs for labor and brick. The labor cost is high because all checker-brick have to be handled twice. The brick cost is high because many of the bricks are spalled in the double handling, rendering them useless because a spalled brick will not stand up. 2. The top courses of brick become coated with iron oxide, etc., melt clown, and large amounts of dirt are deposited throughout the checkers, especially at the bottom. The draft of the furnace is decreased by the closing of the top and bottom openings, especially the top ones, and the entire working of the furnace is affected. If an effort is made to clean the checkers the dirt and brick falling down into the holes still further diminish the draft. 3. The distribution of the air or waste gases through the checkers is in many cases uneven, resulting in a lower temperature of pre-heated air and therefore a slower working furnace. Also, the passage of air and waste gases is so crooked that sometimes the chimney is not powerful enough to overcome the friction.

Jan 6, 1913

By Linda P. Bono

Some mining engineers are pursuing their destinies in places far removed from what they might have envisioned back in the classroom. The path they follow to work each day may wind down Wall St., Park Avenue, LaSalle, or Market; their offices are in modern skyscrapers which offer all the amenities-air conditioning, thick carpets, attractive decor, and executive lunchrooms, to name just a few. The papers on their desks are a combination of financial figures and feasibility studies. But even in these surroundings there are indications of what these men do and where their professional interests lie-minerals are everywhere, from vast collections to one symbolic paperweight. . . there are sometimes specks of dirt under fingernails from a recent on-site inspection, belying the traditional banker's garb. . . and there are the wistful comments about finding it necessary to get out in the field.

Jan 9, 1978

AT the meeting of January 28 which was held too late to be reported in the February MINING AND METAL-LURGY, Messrs. Taylor, Barron, Bassett, DeGolyer, Hutchinson, Norris, Rand, Reynders, Smith, Sweetser and Callow were present. Aside from routine matters, relating to finances and membership,, the Board author-ized establishment of a payroll account and payment by check. It also approved plans for a regional meeting to be, held at Cleveland on April 19 and 20 under the auspices of the Ohio Section and the Iron and Steel Committee. Following a report from the Committee on increase of Membership, Messrs. Barron, Bassett, and Sweetser were appointed as a special committee to con-sider the feasibility of increasing the dues. Mr. Read was made secretary of this Committee. A pleasant feature of the meeting was the presence of past-presi-dent Olcott and the presentation by him to the Institute of an elaborate scrap book, covering the excursion through Mexico made by the Institute in 1901. The meeting was preceded by a dinner at which Scott Turner spoke of the problems of the Bureau of Mines and the large volume of service work for the govern-ment it was now called on to perform. M. L. Requa discussed the need of more exact data covering our national reserve of minerals. E. N. Cooper gave a vivid picture of conditions in Mexico. W. H. Bassett told of the problems before the Institute of Metals, and Zay Jeffries told of the plans for that Division now being formulated. Max W. Ball reinforced what Mr. Requa had said relative to the importance and value of conservation studies as relates to minerals.

Jan 3, 1927

The meeting of the Board of Directors, on November 22, was attended by eight directors, the Secretary of the Institute, and eight guests. The proposed James Douglas Prize and Tablet was referred to a committee of eleven. Robert H. Richards was appointed representative of this Institute to attend the meeting of the Society for the Promotion of Engineering Education. J. V. N. Dorr was made chairman of the Finance Committee in place of George D. Barron, resigned. The sum of $200 was appropriated for the 1918 expense of the American Engineering Standards Committee; the question of an appropriation for 1919 was referred to the Executive Committee for study and report. The sum of $50 was appropriated to the Treasurer's clerk. The following representatives of the Institute were elected: W. L. Saunders to succeed himself as United Engineering Society Trustee; R. M. Raymond to succeed himself as member of Engineering Foundation Board; S. J. Jennings to succeed himself as member of Engineering Council; George F. Kunz to succeed himself as member of Engineering Council; C. F. Rand to succeed himself as member of John Fritz Medal Board of Award; E. Gybbon Spilsbury to succeed himself as member of the Library Board. To members of the Canadian Mining Institute residing in Canada or Newfoundland, the privilege was extended to subscribe to the Bulletin at the price of $5. An invitation was extended to the Mining and Metallurgical Society of America to consolidate with the American Institute of Mining Engineers. The appointment of Engineering Societies' Employment Bureau was reported. Thirty-nine members and ten associates were elected. Two members were reinstated. Extension of time for the payment of clues was granted to four members. Seventeen members on active duty at the front had their dues remitted.

Jan 1, 1919

By H. D. Hoskold

This instrument, shown in Fig. 1, is not generally known, though it has been used in England, and found very practical, handy and useful in work not requiring a transit or theodolite. It is not only a good miner's dial, but a circumferentor as well; that is, it can measure horizontal angles like a theodolite. The magnetic bearings are conveniently read on the inward-beveled upper divided circle; while another circle, graduated on the base-plate, is used for reading the horizontal angles with a vernier. Two leveling spirit-bubbles are sunk in the same base-plate. The vertical divided semicircle is attached to the compact-box by two short axes, which permit the semicircle, with its plain sights, to be turned down to a horizontal position, and rest upon a pin, which relieves the axes from strain. This adjustment gives a clear view of the needle and vernier, and protects the instrument from injury, when carried through low mine-workings. A groove in the semicircle receives a sliding-bridge which carries the plain sights, and a vernier for reading vertical angles. A ball-and-socket-headed tripod is used; but sometimes the instrument is mounted on parallel-plates and level-ing-screws; and sometimes a telescope is attached, instead of the plain sights. The instrument is admirable for all such Mexican surveys as Mr. E. A. H. Tays describes ;l and saves so much time and labor as to be vastly superior to the less accurate hanging-compass called by him a " bully " instrument. If the hanging-compass was ever used in England, it has long since given way to more modern and superior instruments.

Jan 1, 1905

By R. Clare Coffin

The production of oil in the Rocky Mountain district, including southeastern New Mexico, increased from 33,048,630 bbl. in 1930 to 34,325,163 bbl. in 1931. This increase was due to production in New Mexico, which exceeded the 1930 figure by approximately 5,000,000 barrels. Total production by fields is given in Table 1. Exploration during 1931 resulted in the discovery of a new oil-producing horizon in the Big Muddy field in Natrona County, Wyoming, and ' the discovery of a new gas pool in the Powder Wash structure, Moffat County, northwestern Colorado. Gas was discovered also in the Frontier sands of the Bunker Hill dome, Carbon County, Wyoming, but no test has yet been made by which to determine the significance of this discovery. All other exploration which resulted in increasing the known reserves of oil and gas in the district was confined to drilling in partly outlined fields where known limits of production were extended. During the year two major gas pipe lines were completed in western Montana, and one in southwestern New Mexico was extended into Arizona. One new project involving the marketing of natural gas from Wyoming fields included the conversion of an existing oil line to a gas line to serve towns in southeastern Wyoming and western Nebraska. Colorado The decline of 132,501 bbl. in the production of oil in the Colorado fields during 1931 from the figure of 1930 is due to the natural decline of existing wells, partly offset by the increased production in the Greasewood area. New exploration was limited largely to northeastern Colorado, where attempts were made to find oil in areas adjacent to the Grease-wood field. Powder Wash, Moffat County.—The Ohio Oil Co. is to be credited with the discovery of a gas field in the Power Wash structure in Moffat County, Colorado. The initial well drilled in sec. 5-11-97 encountered a sand at a depth of 2152 ft. which produced 34,188,000 cu. ft. of gas on an open-flow test. The rock pressure was reported as 630 Ib.

Jan 1, 1932

By Charles F. Manness

In the great increase of product which has been accomplished in the American Bessemer plant, through improvements in machinery and refractories, and by more perfect skill in their manipulation,

Jan 1, 1881

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien's article' describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation. Some attempts were made in 1931 by the owners of the Hawkesworth patents to interest Ontario gold mine operators in the bit. These efforts were not successful, but they undoubtedly stimulated thinking which resulted in the invention and patenting of several well-known Canadian detachable bits, one of which is now a widely used throwaway bit. The success of the Butte installation also led to the development of the threaded type of bit connections by several well-known manufacturers, and in 1935 these bits were introduced to the mining industry on a national scale. The original Hawkesworth bit was not provided with a water hole but, depended upon water passing through the clearance opening between the tongue in the bit and the groove in the rod to flush cuttings from the drill hole, see Fig. 1. In December 1935 it was found that this method of introducing drilling water to the bit face resulted in high dust counts. To correct this a water hole was drilled on the central axis of the bit, passing through the tongue. Unfortunately, quenching water would rise through the small water hole, spot-hardening the tongue to cause breakage, never completely eliminated. In the fall of 1936 large-scale tests indicated that savings would be effected by use of a threaded type of bit, which was therefore adopted as standard for all Butte mines. This type of bit was used until 1947, when it was superseded by a one-use slip-on type. Since the first use of the Hawkesworth bit every detachable bit of importance has been investigated, and where advantages which might reduce costs or increase efficiency were indicated, substantial tests of the bit were carried on in the Butte mines. When tests demonstrated the advisability of changing from one kind of detachable bit to another the change was made at one level or in one area each day until the new rod and bit equipment was used throughout the mine. This involved a minimum of cost and disruption of drilling. Intelligent selection of a detachable bit to obtain optimum results requires careful consideration to achieve a balance between the three principal types of equipment used in the drilling process: 1—drill bits, 2—drill steel, and 3—drilling machines. Optimum results imply maximum output and minimum cost per unit of output. Since every rock type differs in drillability and it is generally impractical to provide equipment for more than one or two types of rock which may occur in one operation, selection of equipment must encompass average drilling conditions. However, on exceptional occasions several widely differing conditions may make it mandatory to provide equipment best suited to each condition. The choice of rock-drilling equipment is a most controversial subject and one that is further complicated by unreliable and frequently misleading performance claims. Small operators without the means for making accurate evaluations of equipment frequently suffer from these over-enthusiastic claims. It is apparent from experience in rock drilling throughout the world that rock drillability is not alike in any two places, and that selection of proper equipment can only be made after conducting thorough trials of various types of equipment. Some recent drilling tests in tactite and hornstone at the Darwin, California mine of the Anaconda Co. present some interesting clues on rock drillability. Microscopic examination of thin sections of these rocks reveals that mineral composition and rock texture are equally important in governing drillability. The Darwin hornstone is at times so abrasive that the carbide bit cutting edges become flattened to 3/32 in. in 2 to 4 ft of drilling, and some carbide bits were dulled to this point after 9 to 10 in. of drilling. This wear was determined to be the proper point for resharpening to eliminate carbide insert breakage or breakage of the steel rod when drilling with 1½ to 1?-in. bits, with a drifter of 2 3/4-in. diam and 90 to 100 psi air pressure, see Supplement A. Before considering the merits of various bit designs it may be well to review the mechanics of drilling rock with percussion drills. A sharp bit cuts by penetration and chipping. The amount of penetration governs the amount of chipping and depends upon the contact area of the cutting edge, the foot-

Jan 1, 1954

Fifty to 75 million years ago, hydrocarbon-bearing rocks were formed in the Green River formation of Colorado, Wyoming and Utah. The hydro- carbons can be extracted from these rocks, marl- stone but misnamed oil shale, after crushing and intense heating. At about 900°F the marlstone decomposes to produce liquid shale oil. A press release from the Colony Development Co. describes a process which may permit, for the first time, economically feasible access to shale oil. Shale oil has resisted economic extraction for almost three centuries. According to the USBM, a patent was issued as early as 1684 in England to produce "oyle from a kind of stone". France produced oil from marlstone in 1838 and a dozen years later, Scotland started an oil shale industry, producing kerosine, that lasted nearly 100 years. In both countries, the process involved crushing the stone and retorting it to decompose the kerogen-a long and costly process at that time. In 1859, Edwin L. Drake brought in the first oil well in Titusville, Pa., and shale oil faded into oblivion.

Jan 8, 1965