Search Documents

By F. P. Schwarz, A. J. Erickson, S. M. Weber

The Mount Hope stockwork molybdenum deposit, Eureka County, Nevada, occurs In a small igneous cauldron complex 32 to 38 mybp in age. The deposit is characterized by alteration zones and mineralized shells symmetrically distributed around multiple intrusive. For samples from the 25000 meters of 1981-82 drilling, an appraisal of error in in-house sample preparation and in commercial assaying has been made. After splitting, drill core is crushed and reduced in volume (8: 1 at 10-mesh, 8: 1 at 70-mesh, 6: 1 at 200-mesh) to supply 25 grams of 200-mesh pulp for replicate analyses. A 0.5 g portion of the pulp 1s used for dissolution and atomic absorption analyses. Factors which initially generated unacceptable data variances have been minimized by planning, repeat analyses, introduction of standards, and routine monitoring. Assuming that error between replicate assays defines a Gaussian distribution with its average ideally equal to zero, precision (from preparation including core splitting and analysis of 8400 pairs of molybdenum samples) is on the order of ± 25%. The error distribution is not based. Accuracy is approximately 4% lower than absolute as determined by replicate assays of commercially prepared samples.

Jan 1, 1984

By P. Chiotti, J. T. Mason

Ther?nal, X-ray, metallographic, and vapor pressure data were obtained to establish the phase diagram and standard free energy, enthalpy, and entropy of formation for the compounds in the Sw-Zn system. Four compounds, SmZn, SmZn2 , SmZn4.s, and SmZn8.5, melt congruently at 960°, 94Z°, 908°, and 940°C, respectively. The cornpounds SlnZns, Sm3Znll, and SnzZn7.3 undergo peritectic decomposition at 855", 870°, and 890C, respectively. Another compound of uncertain stoichiometry, SmZn11, undergoes peritectic decomposition at 760°C. Four entectics were observed with the following compositions in weight percent zinc and eutectic tenzperatures in degrees Centigrade: 12 pct, 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. An allotropic transformation and a composition range were observed for the SmZnz compound. The transfor)nation varies from 905" to 865°C as the zinc content increases from 16.0 to 48.5 wt pct, respectively. The free energy of formation of the compounds at 50PC varies between -15.9 kcal per mole for SmZn to -51.1 kcal per mole for SmZn,.,. Corresponding enthalpies vary between -19.2 to -78.3 kcal per mole. The ther-modynamic properties for the liquid alloys are described by the relations: A search of the literature revealed very little information on the Sm-Zn system. Chao et al.&apos; as well as Iandelli and palenzonai have reported the structure of SmZn to be cubic B2 type and Kuz&apos;ma et al3. have reported the structure of -sm2zn17 to be of the Th2Ni17 type. The purpose of this work was to establish the phase diagram of this system, to determine the zinc vapor pressure over the solid two-phase regions of the SYstem, and to calculate the thermodynamic properties of the compounds. MATERIALS AND EXPERIMENTAL PROCEDURES The metals used in this investigation were Bunker Hill slab zinc 99.99 wt pct pure and Ames Laboratory samarium. Analysis of the samarium by chemical, spectrographic, and vacuum-fusion methods gave the following average impurities in ppm: Nd, <200; Eu, <100; Gd, <100; Y, <50;Ca, 225; Ta, 400; Mg, 10; Cu, ~50; 0, 175; H, 20; and N, 15. The elements Fe, Si, Cr, Ni, Al, and W were not detected. The samarium was received as sponge metal and was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys with zinc contents up to the Sm2Znl, stoichio-metry. At higher zinc contents the grain boundaries of the tantalum containers were penetrated by the alloy and the containers failed during prolonged annealing. About 25 g of massive zinc and samarium sponge were sealed in tantalum crucibles equipped with thermocouple wells. These crucibles were in turn sealed in stainless-steel jackets. All closures were made by arc welding under an argon atmosphere. The samples were equilibrated in an oscillating furnace and in some cases were given various heat treatments in a soaking furnace. After appropriate heat treatment the steel jackets were removed and the alloy subjected to differential thermal analysis. The apparatus was calibrated against pure zinc and pure copper and found to reproduce the accepted melting points within 1°C. Alloys were subsequently subjected to metallographic examination and those of appropriate compositions were used for X-ray diffraction analysis and for zinc vapor pressure determinations. The vapor pressures were determined by the dewpoint method. Both the differential analysis and dewpoint measuring apparatuses have been described in earlier papers.4, 5 All alloy samples were etched with Nital (0.5 to 3 pct nitric acid in alcohol) except the samarium-rich alloys. These more reactive alloys were electro-polished in a 1 to 6 pct HClO4 in methanol solution at -700c at a potential of 50 v. EXPERIMENTAL RESULTS Phase Diagram. The results of thermal analysis are indicated by the points on the phase diagram, Fig. 1. Eight compounds and four eutectics were observed. The composition of the compounds and their melting or peritectic temperatures are given on the phase diagram. The four eutectic compositions in wt pct zinc and eutectic temperatures in % are: 12 pct,- 680°C; 36 pct, 890°C; 58 pct, 850°C; and 72 pct, 900°C. The stoichiometry of the most zinc-rich compound is still uncertain, but is very likely either SmZnll or SmZnlz. However, to simplify the presentation which follows it will be referred to as SmZnll. As shown on the phase diagram the phase regions for some of the samarium-rich alloys have not been unambiguously established. A sample of pure samarium was observed to transform at 924°C and to melt at 1074"C, in good agreement with corresponding val-

Jan 1, 1968

Dr. Oldshue has provided a useful summary of a voluminous subject and my task will be to select and direct attention to those areas of mixing theory and practice which are germane to mineral processing in general, and to fine particle treatment in particular. Pulp mixing in impeller actuated reactors occurs in mineral processing in several different applications: (1) emulsification of reagents; (2) mixing pulp with &apos;reagents as in conditioning for subsequent operations (such as flotation, flocculation or agglomeration) ; (3) high intensity agitation, as in (a) disintegrating and dispersing aggregates, and (b) aggregating particles as in shear flocculation or in selective agglomeration; (4) hydrometallurgy; (5) hydrometallurgy with gas phase (e.g., Arbiter process); . (6) flotation in sub-aeration machines. Attention is invited to 3 above in which two opposite effects can be induced by proper choice of chemical treatment and hydrodynamic conditions. Successful processes for treating mineral fines require excellent aggregate dispersion in order to fully accomplish the liberation stage. Some processes depend further upon selective aggregation following dispersion. The term “dispersion” is often used in different senses which for present purposes will be clarified at the bottom of the next page.

Jan 1, 1979

By E. B. Burwell, R. H. Nesbitt

A NEW milestone in the progress of photography and subsurface exploration was reached when the Chief of Army Engineers announced the development of the NX borehole camera. In obtaining continuous undistorted cylindrical color pictures of dry or water-filled borings the device surpasses all other cameras designed for photographing interior surfaces of pipes, wells, and conduits. The usefulness of the camera and the unique projector that comes with it are at once apparent. To the geological, mining, and civil engineer alike it signifies the end of guesswork with respect to underground conditions that have eluded identification by conventional core-drilling methods. To the medical profession it may well signal new progress in photo optics which could result in cylindrical color photographs supplementing the X-ray and existing photographic methods used in exploratory surgery.

Jan 8, 1954

US 4,152,143-Continuous precipitation of cement copper from an aqueous ore leach solution mixed with pieces of iron as the precipitant Copper depositing on the pieces of iron is loosened and removed therefrom by means of constant but regulated oscillating movement of the pieces of iron in a horizontal elongated chamber, and the loosened copper is separated and collected from the mixture E Kausel and R Nissen, assigned to Klockner-Humboldt-Deutz A G May 1, 1979 8 pp (75-100) Filed 1-12-78 (868,981) (Drawings below) [ ] US 4,156,711-Removal of metal impurities from an acidic zinc or cadmium solution prior to electrolysis. Impurities such as manganese, cobalt, nickel, and thallium are selectively precipitated by contacting the solution with persulfuric acid or an ammonium or alkali metal salt thereof while maintaining a pH value of from 1 5 to 4 5 This patent is a continuation-in-

Jan 1, 1980

"Located on the Big Hole River, three miles from Divide, Montana, and 21.75 miles from Butte.Built in 1899.DAM: Rock-filled wooden crib, 512 ft. long and 57.5 feet high.SPILLWAY: Equipped with flash-boards 189 ft. long, 8 ft. 10 inches high.PENSTOCKS: Two 8 ft. diameter of steel, each branching and supplying two wheels.WHEELS: Four double horizontal, double discharge turbines, made by The James Leffel & Co., 1,000 h-p., 180 r. p. m., direct connected to generators, operating at 60 ft. head. GENERATORS: Four G. E., revolving field, 750 k-w., 180 r. p. m., 800 volt, 3 phase, 60 cycle alternators.EXCITERS: Two water-wheel driven exciters.TRANSFORMERS: 12 250-k-w. G. E. air blast, primary 15,000 volts, Secondary 800 volts.OPERATION: The plant operates essentially as a peak load plant. Except in flood period, there is insufficient water to operate at full load continually. In December its average output is about 500 k-w."

Jan 1, 1913

By T. Saburi, C. M. Wayman

The massive and martensitic transformations in ß Cu-Ga alloys were studied by optical microscopy and by transmission electron microscopy and diffraction. These types of transformation are distinct and do not merge into one another. An internal fine structure due to stacking faults was found in both the massive phase (m) and the martensite, but the origin of the faults is believed to be different in each case. The faults in the martensite are due to the lattice invariant or "second" shear of the phenom-enological theory, while those in the are probably growth faults and deformation faults arising from the transformation volume change. Evidence is presented for ordering in the ß phase prior to transformation into martensite, and the crystal structures of and ß&apos; and ßi martensites are discussed. THE results from some previous investigations1,2 have led to the suggestion that martensitic and massive transformations have certain common characteristics. It presently seems established that massive transformations like martensitic transformations are essentially diffusionless,1,2 but unlike martensitic transformations, when a new phase forms massively there is no shape change or surface relief.= If the massive-type transformation is crystallographically similar to martensitic transformations, one would expect a fine structure as a result of the lattice invariant shear4 which is a part of the transformation mechanism. The existence of such a fine structure (i.e., slip, twinning, or faulting), if any, can be verified by transmission electron microscopy, and thus the present investigation was undertaken to compare the internal structure of massively and martensitically formed phases in Cu-Ga alloys which were derived from a parent of the same composition. The transformation characteristics of ß Cu-Ga alloys were also studied. The bcc ß phase in the Cu-Ga system, Fig. 1, is stable above 616oc.&apos; Depending upon the cooling rate, ß Cu-Ga alloys can undergo three different types of phase transformations. The ß phase of eutectoid composition (23.7 at. pct Ga) decomposes into the ? phase (hcp) and the phase (complex cubic) by means of a eutectoid reaction. When the cooling rate is increased so that the decomposition of 0 into [ and ? is suppressed, the ß phase transforms into a nonequilibrium hcp phase, herein denoted ?m by a process of very rapid growth called a "massive" transformation. At even faster quenching rates the massive transformation can be suppressed and the ß transforms martensitically. Massive transformations, apparently similar to those in the Cu-Ga system, have also been studied in the Cu-Zn2,6-8 and Ag-Cd systems.9 Definitive characteristics if the Massive Transformations in 0 Cu-Ga Alloys1 1) The most remarkable feature of the massive transformation in Cu-Ga is that there is no bulk composition change on transformation. According to Massalski,1 the resulting [, phase is a supersaturated extension of the equilibrium [ phase. The lattice parameters continue the trend exhibited

Jan 1, 1965

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the&apos; second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson&apos; argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By J. H. Anderson, G. A. Parks, B. K. Jindal, H. Leslie Bullock

H. Leslie Bullock (Engineering Consultant, Oak Park, 111.) — In reading over the paper, I find that I have no quarrel with the thoroughness of investigation of the points studied, but I am forced to question the selection of oxides from oxides as the subject of the investigation, the inclusion of silica gel as an example, and to question the validity of some of the conclusions. Separation of oxides from oxide, in minerals where the liberation of values is possible by grinding, are comparatively rare. Most oxides are only slightly soluble and the action of carbon dioxide or other acid forming ingredient in the air must be added to humidity to produce surface action. Silica gel is a very special synthetic substance in which the adsorption is determined by total surface, pore dimensions and temperature. Quartz is our most prevalent oxide and its action in electrostatic separation is far more sensitive to its three thermal transition points than to humidity.

Jan 1, 1968

JOHN H . NELSON,*Worcester, Mass.-In reply to the question "Is there any final information in regard to the relation between the temperature or the rate of cooling of a piece of heat-treated steel from the drawing temperature, and the so-called notch toughness?" I might say that we have conducted a large series of tests in the study of impacts on chrome-nickel and carbon steels and have gone into the subject of quenching from drawing temperature quite thoroughly but have found that one cannot lay down any definite rule or law with respect to the effect of quenching from the drawing heat. We conducted experiments on the effect of cooling by quenching in water, cooling in air, and burying the coupon in lime. Steels that have practically no impact value when air cooled may show very marked results when they are quenched in water, depending on the temperature at which the drawing is done.

Jan 6, 1919

[ ]

Jan 1, 1946

By Persifor Frazer

TILE ore property of Mr. Augustus Roop is situated about one and a half miles south of the New Windsor Station of the Western Maryland Railroad and is connected with the town of New Windsor by the Liberty and New Windsor Turnpike. It is about forty miles distant from Baltimore, and about seven miles west from the county town of Westminster, and a little more northeast from the celebrated Liberty Copper Mines. (See accompanying Maps 1 and 2.) The property comprises about 140 acres, lying principally

Jan 1, 1881

By James H. Pannell, John Dasher, Wilfred L. Freyberger, A. M. Gaudin

A new sorting process for beryllium minerals is described. This depends upon emission of neutrons upon irradiation by gamma rays, a nuclear reaction which is specific for beryllium at the appropriate energy level. Signals given by neutrons when ore passes on a belt are changed to mechanical commands through amplifiers and other electrical equipment.

Jan 4, 1950

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman A. A. STEVENSON, Vice-Chairman HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. Guilliaem Aertsen, Henry M. Howe, E. Gybbon Spilsbury, John Birkinbine, _Robert-W. Hunt, J, S. Unger; William-H. Blauvelt, J:-E: Johnson, Jr., Felix A: Vogel; Charles A. Buck, Charles Kirchhoff, Leonard Waldo, Ernest F. Burchard, Richard Moldenke, William R. Walker, F. D. Carney, Charles F. Rand, William R. Webster, James Gayley, Joseph W. Richards, Frederick W. Wood. Henry D. Hibbard, C. F. W. Rys, There will be a meeting of the Institute in Pittsburg on Oct. 8, 9, and 10, 1914. This meeting will be under the joint auspices of the Iron and Steel Committee, the Committee on Coal and Coke, and the Committee on Petroleum and Gas. The iron and steel papers will probably be presented on Oct. 8. The following papers have been received and accepted and will be read at the October meeting.

Jan 6, 1914

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1935 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. Copies of the TECHNICAL PUBLICATIONS have been mailed to members of the Institute that are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Industrial Minerals Division (Nonmetallics); I-Mining Geology; J-Mineral Industry Education Division; K-Mining Administration; I-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Copies of CONTRIBUTIONS may also be obtained from the Secretary&apos;s office. Additional copies are sold at the rate of 1 cent per page; minimum charge, 25 cents. Nonmembers may purchase the papers at the prices mentioned. [ ]

Jan 1, 1936

By Persifor Frazer

The ore property of Mr. Augustus bop is situated about one and a half miles south of the New Windsor Station of the Western Maryland Railroad and is connected with the town of New Windsor by the Liberty and New Windsor Turnpike. It is about forty miles distant from Baltimore, and about seven miles west from the county town of Westminster, and a little more northeast from the celebrated Liberty Copper Mines. (See accompanying Map I and 2.) The property comprises about 140 acres, lying principally

Jan 1, 1881

By K. F. Veit, R. L. Marovelli, T. S. Chen

There is an error at the bottom of the right-hand column of p. 11, and the top left-hand column of p. 12. The first paragraph of the section EXPERIMENTAL RESULTS should read: "Thermal shock tests were conducted on circular discs of basalt, quartzite, and taconite. Average grain sizes ranged between 0.10 and 0.25 mm. Individual discs were tested only once, either in a cooling or heating shock. Several discs of the same rock type were shocked at a temperature, and the temperature level then was increased for another test by 10° to 20°F until complete fracture occurred when a specimen was quenched. The minimum temperature difference required to initiate cracking, TmiN was observed and used, together with other property values, to compute the dimensionless stress o*max . The observed ?Tmin for cooling shock in different media is tabulated in Table I. The property values E, St, a, and K are shown in Figs. 6, 8, 10, and 11, respectively. Discs of various rocks shocked in different isothermal baths gave o*max values for a wide range of Biot numbers. These o*max values were then compared with the theoretically predicted values."

Jan 1, 1968

By Michael A. Zappia

INTRODUCTION The San Manuel mine of Magmacopper Company is located approximately 72 km northeast of Tucson, Arizona. The mine, concentrator, smelter, electrolytic refinery and continuous rod casting are located on the west side of the San Pedro River valley. Ore Production: 58 1W mtpd Production To Date: Over 340 000 000 mt since 1956. Ore Grade: 0.70% net sulfide cu. As conceived at the present time, the San Manuel ore body is the lower half of what was originally an elliptical (In cross sect ion) cylinder same 2400 m long with major and minor cross sectional axes of 1500 m and 760 m. After emplacement, the cylinder was diagonally sliced along its long dimension by the San Manuel fault, which separated it into halves, moving the upper half same 2500 m down dip and bringing a wedge-shaped blanket of tertiary conglomerate into position over the lower segment of the cylinder. The lower segment is the San Manuel ore body. The upper part, moved down dip, is the Kalamazoo ore body. Originally, these were one ore body. The San Manuel ore body is a structurally weak and highly fractured quartz monzonite, the principal ore minerals being chalcopyrite, with small amounts of molybdenite. The present mining method is full gravity diagonal retreat panel caving by block. This is shown on Figure 2 , (Block Sequence 56, 57, 58, 59 --on the following page.) The ore mined is hoisted to the surface for transportation to the concentrator. BLOCK CAVING MINING SEQUENCE HISTORY The San Manuel mine was planned and developed as a full gravity block caving mine. It continues as a full gravity block caving mine. Since its initial start, the major changes in mining have been in the areas of ground support, rate of draw and undercut sequence. Ground weight resulting from block caving plays a dual role. It can cause extensive damage to ex- traction openings, yet it is necessary to break the ore into easily handled size. The ground- weight problem resolves itself into finding ways to make it manageable. The initial early ground support in the production areas consisted of timber sets and various combinations of steel and timber sets. This sup- port system proved unsatisfactory and a new support system utilizing concrete was developed. Concrete support, 30 cm to 45 cm thick, proved satisfactory. Rates of draw were experimented with. A draw rate of 45 cm to 61 cm (32 to 45 mt) per draw point per day was determined as optimum in con- trolling ground weight. Undercut sequence or mining sequence was recognized as a major contributing factor to ground weight. This is the most difficult factor to change. The lead time from primary development to undercut can be as much as two years. Initial Checkerboard Pattern The initial undercut sequence was in a checker- board pattern (Figure 2). Blocks Sequence 1, 2, 3, 4, 5, 6--next page.

Jan 1, 1981

An informal meeting of the Conferees of the Development Committees of the four Societies was held in New York on July 2, 1919, at which the scope of the work was considered, and a sub-committee oil Procedure, consisting of the chairmen of the Conferees from each of the four Societies, was appointed to arrange the program for and the time and place of the first formal meeting. The Conference subsequently adopted the name, " The Joint Conference Committee." The Joint Conference Committee convened at the Hotel Montclair, Montclair, N. J., Aug. 13, 14, and 15, and in New York, Sept. 15, 16, and 17, 1919. The Committee has divided its report into two parts, that covering the public activities and that covering the society activities of common interest to the four societies.

Jan 12, 1919

By AIME

Generally speaking, the mining industry had a good year in 1948 with most mineral products being produced in record quantities for peacetime standards. The big boys-iron and steel, coal, and petroleum-indicated the industry-wide trend by surpassing 1947 production figures. Although exploration and expansion are being pushed aggressively in all branches of the industry, there is a pronounced trend to engineering and research directed at cutting production costs, improving the product, and finding new markets. These improvement campaigns are making headway; in the bituminous coal industry, 5.43 tons per man employed is the new production record; 83 million tons of iron ore were unloaded at lower Lake ports, breaking another peacetime record; magnesium, due to improvement in manufacturing techniques, now competes on the market with aluminum.

Jan 1, 1949