Search Documents

By Robert H. Richards

(Read at the Amenia Meeting, October, 1877.) DURING the winter of 1868-9, I was called upon by Professor F. H. Storer, to put up the Bunsen filter pump in the chemical laboratory of the Masschusetts Institute of Technology. As the laboratory is on the lower floor, it was found necessary to use a great deal of cumbrous pipe and apparatus to get the necessary column. It was then suggested that if an instrument could be devised which would make use of the hydrant pressure in the service-pipe, it would do away with the objectionable features of the Bunsen pump. After using the Bunsen pump for some years, the jet pump to be described in this paper was devised, and it has since been adopted by Prof. Wing in the quantitative laboratory of the school. I am much indebted to Prof. Wing for his aid in starting the manufacture in brass of these jet pumps, which are now to be had in Boston. The jet pump much resembles the Giffard injector in form. It differs from it in the fact that water is the impelling fluid, and air the impelled, while with the injector steam is used to impel water. The principle of condensation of steam, which is Water availed of in the injector, is entirely wanting in the jet pump. The jet pump consists in a water jet, w, (see figure), a constriction or waist, a, and a waste tube, o. The success of the jet pump depends on the following conditions 1. The relation between the sizes of sectional area of a and w. 2. The proximity of a and w. 3. The form and angle of the two hollow cones whose vertices make the constriction a. 4. The relative size of sectional area of w and o. 5. The zigzags, or an equivalent means of making foam. In the following discussion, let a, w, and o represent the diameters of these parts of the jet pump. A number of experiments were tried to ascertain

Jan 1, 1878

By T. A. Klinefelter, R. G. O’Meara, Glenn C. Truesdell, Richard W. Smith

THE investigation of domestic tales was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. I, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." HISTORY The use of steatite and talc in ceramic bodies goes back a great many years. If pure, tales shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a large business was carried on in the manufacture of tips for gas burners.1 With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Manchurian tales. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1943

By P. A. Beck, A. Merlini

Quantitative texture determinations were made for rolled and for rolled and annealed strips of 3, 6, and 10 pct Zn brasses. The main components of the rolling texture gradually shift over a wide composition range from the orientation characteristic of copper to that of 70-30 brass. At least the main features of the corresponding gradual changes in the annealing texture may be accounted for qualitatively on the basis of the oriented growth theory of annealing textures. All the oriented nucleation-type theories are notably less successful in accounting for the observed textures. EARLIER investigations by von Goeler and Sachs,' Dahl and Pawlek,' and Brick, Martin, and Angier" suggested that the annealing texture of copper is more sensitive to the addition of solute elements than the rolling texture. It was reported3 that the cube texture changes over into a brass-type recrys-tallization texture on addition of about 1 pct Zn, while the deformation texture changes only at about 5 pct Zn. Such behavior would be difficult to reconcile with any theory of annealing texture formation that relates the annealing texture to the deformation texture. In particular, the oriented growth theory of the cube texture" is based on a certain orientation relationship between the cube texture and the main components of the deformation texture which could not be reconciled with the reported behavior of low brasses. It was, therefore, of interest to re-examine these textures by means of the quantitative methods now available. The deformation and annealing textures of rolled a brasses with approximately 3, 6, and 10 pct Zn have been determined in terms of (111) and (200) pole figures. Experimental Methods The chemical analyses of the Cu-Zn alloys of commercial purity used in the present work are given in Table I. Chill-cast bars of the tabulated compositions were rolled and annealed according to the following schedule: I—rolling from 1.2 to 1.02 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 2— rolling from 1.02 to 0.867 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 3—rolling from 0.867 to 0.600 in. thickness, 31 pct reduction area, annealing 2 hr at 540°C; 4—rolling from 0.600 to 0.400 in. thickness, 33 pct reduction area, annealing 2 hr at 480°C. In the final straight rolling of 96.25 pct reduction area, the strips were reversed end to end after each pass. The final annealing temperature was determined for each alloy by annealing specimens of the cold-rolled strips in salt bath for 5 min at varying temperatures. The results of the hardness measurements are given in Fig. 1, where the final annealing temperature used for each alloy in determining the annealing texture is indicated by a cross.

Jan 1, 1956

[For the year ending February, 1936 PRESIDENT AND DIRECTOR HENBY A. BUEHLER3 ROLLA, Mo. PAST PRESIDENTS AND DIRECTORS FREDERICK M. BECKET1 NEW YORK, N. Y. HOWARD N. EAVENSON2 PITTSBURGH, PA.]

Jan 1, 1936

By the courtesy of Sir Robert Hadfield, we have received the fol¬lowing communication relating to the development and encouragement of science and research in Germany at present. These statements have been translated by Sir Robert from various German sources, and are presented here as an indication of what Germany is doing not only to further her military power, but also to prepare for the period of trade rehabilitation to which she is looking forward after the close of, the war. KAISER WILHELM TRUST FOR PROMOTION OF WAR SCIENCE The Kaiser has approved the foundation of a Trust with the name given above. The aim of the Trust is to further the development of scientific and technical aids to warfare, by uniting the scientific and the military forces of the country for work together. The scientific Work is to be carried on by the following technical committees (or commissions) (1) Committee for the chemical raw materials, for the production of munitions-manufacturing materials. (2) Committee for chemical war materials (powder, explosives, gas, and the like). (3) Committee for physics, including ballistics, telephony, telegraphy, determination of targets and distances, measurements, and the like. (4) Committee for engineering and communication. (5) Committee for aeronautics. (6) Committee for obtaining and preparation of metals.

Jan 8, 1918

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By Leo Behr

RECENT years have seen important practical advances in the construction of recording instruments for use with thermocouples. The difficulties of the problem will be appreciated when it is remembered that a 10° F. change in temperature of a base-metal couple at 1500° means a change in the electromotive force of about 0.00035 volt. In a circuit having a resistance of 350 ohms, this means a change in the current of 0.00000,1 amp.; and despite this requirement of great sensitivity the instruments must be sufficiently robust to withstand the rough usage which is so often their lot. Two methods are in common use for the measurement of the electromotive force produced by a thermocouple: 1. The milliammeter method, in which the current produced by the thermocouple in a circuit of known resistance is measured and from. this the electromotive force is deduced by Ohm's law. 2. The potentiometer method in which a known potential difference is opposed to the thermocouple electromotive force. The use of thermocouple and milliammeter for measuring temperature introduces some possible sources of error, for the reading depends on a number of factors, including the following: (1) Electromotive force set up at the hot junction, (2) electromotive force set up at the cold junction, (3) resistance of the circuit including thermocouple, lead wires, and meter, (4) field strength of magnets, (5) strength of controlling springs in meter, (6) friction at pivots, of pointer on paper, etc. It is obviously necessary to so design and maintain the installation that the reading is independent of all the factors except the first. The electromotive force set up at the cold junction can easily be taken care of provided it is constant. This has been approximately accomplished by burying the cold junction in the ground or actually secured by locating it in a container, the temperature of which is kept constant by means of a thermostat.

Jan 9, 1919

By Frank C. Greene

Drilling in Missouri in 1939 was marked by wildcatting in the northern half of the state. The total completions numbered 82, exactly half the 164 of 1938. There were 15 gas wells with an initial open flow of 6,383,150 cu. ft., 4 oil wells with about 40 bbl. initial production, and 63 dry holes. The wildcatting followed the widely publicized leasing activity in the Forrest City Basin in northwestern Missouri, northeastern Kansas, southeastern Nebraska and southwestern Iowa. It is worth noting that

Jan 1, 1940

By Frank C. Greene

Drilling in Missouri in 1939 was marked by wildcatting in the northern half of the state. The total completions numbered 82, exactly half the 164 of 1938. There were 15 gas wells with an initial open flow of 6,383,150 cu. ft., 4 oil wells with about 40 bbl. initial production, and 63 dry holes. The wildcatting followed the widely publicized leasing activity in the Forrest City Basin in northwestern Missouri, northeastern Kansas, southeastern Nebraska and southwestern Iowa. It is worth noting that

Jan 1, 1940

By Leon McCulloch

WIIen clean iron and metallic zinc dust, protected from the air, arc heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particlcs are covered with oxide and cannot touch the iron, an extremcly small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clcarly seen while sherardizing small cubes of cast iron, at about 450" C., in a srnall glass-stoppcrcd bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings % in. thick were grown in a few hours. After a heavy layer had been formed, the cubes mere again treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown. A study was made of the effect of iron in zinc dust on the proccss and on the resulting coatings. Glass bulbs, holding the small pieces to be sherardized, together with enough zinc dust to make them two-thirds full, were heated in a small, rotating electrically heated and controlled furnacc. The bulbs had 6-in. (15 cm.) necks, of 96-in. (9.Fj mm.) tubing, plugged

Jan 1, 1923

By Leon McCulloch

WIIen clean iron and metallic zinc dust, protected from the air, arc heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particlcs are covered with oxide and cannot touch the iron, an extremcly small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clcarly seen while sherardizing small cubes of cast iron, at about 450" C., in a srnall glass-stoppcrcd bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings % in. thick were grown in a few hours. After a heavy layer had been formed, the cubes mere again treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown. A study was made of the effect of iron in zinc dust on the proccss and on the resulting coatings. Glass bulbs, holding the small pieces to be sherardized, together with enough zinc dust to make them two-thirds full, were heated in a small, rotating electrically heated and controlled furnacc. The bulbs had 6-in. (15 cm.) necks, of 96-in. (9.Fj mm.) tubing, plugged

Jan 1, 1923

By J. Blodget Britton

During the last three or four years I have had occasion to examine, chemically, various samples of matter commonly called flue-dust or cinder, found deposited in the flues and hot-blast chambers and under the boilers of blast furnaces, and also in the flues and under the boilers of puddling and boiling furnaces. Recently several of these examinations mere made quite in detail, and as the results reveal, I believe, information of no inconsiderable importance, I am induced to communicate them to this Institute. A sample of deposit obtained from the flues of one of the blast furnaces at the works of the Phœix Iron Company, at Phœnixville, Pa., was found to have the composition given in Column I of the following table: I. 11. 111. Composition of Dust from Dust from Dust from Deposits. Blast Furnace. Puddling Furnace. Boiling Furnace. Protoxide of iron,... 1.51 3 08 1.18 Peroxide of iron,... 20.21 33.29 41.00 Alumina,....6.57 12.89 7.54 Lime,.....3.98 .48 .61 Magnesia,.....69 .09 .19 Protoxide of manganese,. . 1.66 .39 .12 Oxide of zinc,....2.84 ........ Oxide of copper,. .. ..06 ........ Silicic acid,....36.00 40.69 38.99 Sulphuric acid,... 7.55 .43 Phosphoric acid,..94 ..94 Arsenious acid,. .. .38 Antimoniousacid,... trace.......... Chlorine,....03 ..03 Cyanogen,.....09 ........ Ammonia,.... trace......... Pottlsh with some sodn,. .. 16.61 ........ Carbonic acid,. .. .. .59 ........ Alkalies, undetermined matter, and loss,.......29 4.49 6.96 100.00 100 00 100.00 Metallic iron,. 16.31 25.70 29.64 Phosphorus,. .. .. .41* 1.55† 1.30†

By David Cole

AT the time flotation appeared upon the metallurgical horizon in Arizona, the writer, under the direction of Dr. Ricketts, was engaged in remodeling and enlarging the No. 6 Concentration Plant of the Arizona Copper Co. at Morenci, and the work had been in progress nearly a year before the Inspiration experiments with flotation had disclosed the revolution in concentration that was at that timè impending. The simplified flowsheet worked out for the remodeling of the Morenci plant had been based upon the removal of the freed metal in a minimum number of stages by treatment upon tables equipped with Butchart riffles, the latter being adapted to accomplish both classification of feed and removal of the metal at one operation, substantially as described in my previous paper.1 The scheme of treatment for the slime was based upon the well-known fact that after copper sulphides, such as chalcocite and chalcopyrite, etc., are reduced to a certain extremely fine state of comminution they are definitely beyond the reach of separation upon any of the concentrating devices then known. By using drag-belt classifiers (which served as conveyors as well as separators), the overflow would be of the usual "slimes" class. Experiment had shown that when these drag-belt overflows were, properly diluted (that is, to about 5 to 7 per cent. solids in the feed under treatment) . the very fine sand, and especially the very fine but still granular sulphide particle's, would, if given a short distance to fall, quickly settle out in prime condition to yield an excellent recovery on vanners; a further valuable feature would be that the very fine non-separable final overflow tonnage might be discharged direct to tailing, thus conserving space requirements so as to permit within the old building, without embarrass-ment, the increase of capacity required.

Jan 9, 1916

By John A. Oberteuffer, James E. Lawver, Ionel Wechsler, Bo Arvidson

INTRODUCTION The demand for aluminum metal and thus for alumina and bauxite (the primary sources), is expected to increase at an annual rate of about 6% through the year 1980. It appears that about 90% of the future aluminum metal requirements could be produced at domestic plants but the production would remain dependent on the use of imported bauxite and alumina. The U.S. dependence on foreign bauxite and alumina is of considerable economic and strategic concern because availability and prices are very sensitive to changes in the political climate in the exporting countries. Dependence of the United States on foreign sources of bauxite closely parallels its dependence on foreign sources of oil, particularly since ten countries, including most of the world's major bauxite exporting countries, recently have formed the Inter- national Bauxite Association (IBA) for the specific purpose of increasing revenue for the participating countries. Although it is clear that long-term aluminum requirements cannot be fulfilled by domestic resources of bauxite,; the U.S. has an almost unlimited supply of aluminous resources such as Kaolinite (38% Al203), Alunite (37% Al203), Dawsonite (35% A1203), and Anorthosite (29% A1203)

Jan 1, 1976

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By T. A. Rickard

T HE life and career of Daniel Cowan Jackling constitute a distinctive part of a passing era, marked by the intensive exploration and exploitation of the mineral resources of the western regions of the United States. In the development of his abilities and in the use of his opportunities, he typifies the initiative, the energy, and the skill of a modern captain .of industry. Daniel C. Jackling was born at Hudson, Mo., on Aug. 1.4, 1869. He was the only child of Daniel Jackling, born in England of English parents, and Lydia Jane (Dunn) Jackling, born in the United States, but of Scottish ancestry. His father died a few months after he was born, and he lost his mother less than two years later. The orphan boy was adopted by his aunt. He went to school as soon as he was old enough to walk the two miles, and back, alone. As opportunity offered, he went

Jan 1, 1937

By L. F. Engle, M. A. Hewedi

SUMMARY Initial interest in using solutions of ammonium salts to leach native copper was documented in notes from an AIME meeting in 1871; By 1916-1917, application of the NH3-CO2-H2O system to recover nonferrous metals attained commercial significance, when it was used as a process for copper recovery by Kennecott Copper Corporation and Calumet & Hecla Mining Company. The Caron work in the early 1920s, Freeport Sulphur Company’s achievements leaching Cuban laterites during World War II, out- standing accomplishments in both eastern and western Canada, recovery of manganese related to the work of Dean -- all serve as landmarks as this One Century Review surveys a base for future technology. Current emphasis on compatibility of metals-producing systems with the need to meet environmental protection criteria provides special encouragement to researchers and engineers to find accept- able ways of recovering metals. The ever-present demand of management to design, build and operate facilities on a profitable basis provides additional impetus to apply information from the technical literature to that need. Examination of the general approach to this paper will reveal much that is firm and positive with respect to empirical results -- extractions, recoveries, amenability to familiar proven equipment and materials of construction common to the industry. Although there are many references, there are gaps in the basic scientific data that if filled could lead to even more usefulness; the paper attempts to indicate where further information is needed.

Jan 1, 1973

By Asheim, Harald A.

Parameter estimates affect both the optimum field development decisions and the economic result. A general methodology for assessment of the effects of parameter uncertainty in offshore development decision situations is proposed, and used to analyze aspects of the initial development situation for the Statfjord field.

Jan 1, 1982

By William H. Love

ATLAS shaft was sunk to explore at depth a portion of the eastern end of the dry belt, or silver belt, of the Coeur d’Alene mining district. The Atlas mine is a mile east of Mullan and is on the south side of the Osburn fault. Equal partners in the venture are Hecla Mining Co., Newmont Mining Co., New Jersey Zinc Co. and Atlas Mining Co., the financing being equally shared by Hecla, Newmont, and New Jersey Zinc. As outlined the project had as its goal deep exploration of prominent structures developed in the Atlas in upper levels. Plans called for deepening the shaft from the 800 level to the 2400 level with subsequent drifting, crosscutting, and diamond drilling on the 2400.

Jan 11, 1954

By C. A. Lemke

THE ores now milled at the Midvale concentrator of the United States Smelting, Refining & Mining Co. come mostly from ;the company's mine in the Bingham district, about 18 miles west of Midvale. Custom ores from this same district and from other western mining districts are also milled at times. The Bingham ores consist of galena, pyrite, chalcopyrite, and sphalerite in a gangue of quartz, quartzite, limestone, and porphyry. The percentage of chalcopyrite is small, usually about 0.5 per cent., while the galena, pyrite, and sphalerite combined constitute about 60 per cent. of the total ore. These three minerals vary considerably' in amount and, at times, all three are somewhat oxidized. The ores also contain gold and silver, the former being mostly in the pyrite while the latter is generally with the galena. The crystallization of the economic minerals varies from fairly coarse to extremely fine. The ores are carried to Midvale by the Bingham & Garfield and the Los Angeles & Salt Lake railroads or by the Denver h Rio Grande Western railroad, in 50-ton, steel, full dump cars. The milling problem is to recover the silver-bearing galena, the gold-bearing pyrite, and the chalcopyrite in a product suitable for the lead smelter and containing the least possible amount of gangue and sphalerite and then recover the sphalerite in a product suitable for a zinc smelter. The minerals are recovered partly by water concentration and partly by water concentration combined with electrostatic treatment.

Jan 9, 1925