Search Documents

By Charles A. Ashburner

[The statistics contained in this paper were collected for the United States Geological Survey and communicated to the Institute, by permission, prior to their publication in the report on the Mineral Statistics of the United States for 1887.1 The total coal-production of Alabama in 1887 was about 1,950,000 short tons, the spot-value of which, at the mines, was $2,535,000. The coal-regions of the State lie in the extreme southern part of the Appalachian coal-field, the northern part of which lies along the western New York-Pennsylvania State line; between these limits, New York on the north and Alabama on the south, portions of the

Jan 1, 1889

By C. W. Dunham

FROM the primary gyratory crushing plant, described in MacLeod's article, ore is delivered to a large storage or surge bin from which it is carried by two transverse conveyors to the secondary crushing plant. The bin has a useful drawoff of about 13,000 tons, this being slightly over one half of the initial daily capacity of the Morenci Reduction Works. This arrangement provides sufficient storage to permit intermittent operation of the primary and secondary crushing plants without too close a coordination between the two.

Jan 1, 1942

By Ingersoll Olmsted

Mr. D. H. BRowne's paper upon " The Distribution of Phosphorus in the Ludington Mine" (Trans., xvii., 616) has interested me very much, and perhaps I cannot give a better proof of that, interest than an account of my work and observations in the same direction while chemist of the Hudson River Ore and Iron Company. The ores of this company lie in a chain of low hills running northwest and southeast, about three miles back from the eastern bank of the Hudson river, below Hudson, N. Y. They occur in thick veins, with the characteristic Hudson river slate formation as hangingrock and foot-wall, and dip about 45' east, outcropping in many places near the top of the western slopes.

Jan 1, 1890

By W. A. Backofen, G. Mayer

Single crystals of iron, copper, and a Cu-7 wt pct A1 alloy were pulled through conical dies to simulate the constraint in a polycrystalline aggregate undergoing axisymmetric reduction. With Taylor-type hardening, dependence of the drawing stress, od, on the Taylor orientation factor, M, is predictable from the polycrystal stress-strain curve; in particular, for a power-law relationship, it should follow that d log od/d log M = (1 + n). A first-order agreement with analysis was found in the data from iron. For copper, the implied n from the observed d log od/d l°g M was -0, while for Cu-7Al it was negative. The trend was in the direction of random polycrystal behavior. Thus the idea of hardening only in response to the amount of prior slip loses validity as stacking fault energy (SFE) is lowered. Two possible explanations have been suggested: as stacking fault ribbons are widened, barriers from dislocation reactions become increasingly effective in dispersing slip and reducing the orientation dependence of the total glide strain dm that appears in alternatively, or conjointly, the polyslip shear stress, 7, acquires an orientation dependence of a kind which has the same leveling effect on M. The problem of relating the strain hardening of polycrystalline material to that of an isolated single crystal is still largely unsolved. In a new experimental approach from recent work, single crystals of different orientations have been deformed under the constraints found in an aggregate while measuring their deformation resistance. Procedures have involved drawing cylindrical crystals through conical dies1 and compressing slab-shaped crystals in plane strain.2'3 Predictions for the outcome of such experiments were made first by Taylor~ and later, in more general form, by Bishop and Hill.5'6 Taylor's example was the axisymmetric extension of an fcc crystal slipping on the usual {111}(110) systems or, equivalently, a bcc crystal undergoing 'kestricted" slip on {110}(111). In his solution, the deformation work supplied was equated to that dissipated internally in slip on all active systems. With o the single applied tensile stress, dc the resulting axial strain, and dyT the total glide strain on systems operating at resolved shear stress, 7: The orientation dependence of M was found by minimizing dyT for each orientation while activating five independent systems, Fig. l(a).? The Bishop and Hill analysis, based on a principle of maximum work, leads to essentially the same conclusion; the need for at least five active systems is recognized in the finding that either six or eight are actually brought into operation. The mean value from the entire stereo-graphic triangle in either case is M - 3.06. More recently, Hutchinson8 made a Taylor-type analysis for pencil glide in a bcc structure, from which piehlerg prepared Fig. l(b) as the counterpart in Fig. l(a); here M = 2.75. The obvious weakness in such analyses is the indifference to slip-system interactions. A condition of what might be termed "independent"

Jan 1, 1969

By Fuad S. Maayeh, Robert J. Evans, Paul M. Yavorsky

A description and capabilities of the Mine Roof Simulator at the Pittsburgh Mining Technology Center is illustrated for testing longwall roof support equipment. This unique Mine Roof Simulator has the capacity to exert 3 million lbs. of compressive force vertically and 1.6 million lbs. of force horizontally to simulate loads on hydraulic supports typically found in longwall mining. The supports that undergo testing are instrumented with strain gauges and photoelastic coatings such that critically strained areas become readily apparent. These critically strained areas are redesigned or retrofitted with appropriate reinforcement and retested. A data base will be accumulated from several support designs that will lead to an optimized design that will have the potential to reduce downtime by malfunctions of supports and thus increase productivity. A typical test procedure and analysis is given for a two leg 350 ton shield along with a description for placement of strain gauges, displacement gauges, and hydraulic pressure monitors for critical sites.

Jan 1, 1982

By Steven Cordiviola, Richard Sergeant

The Kentucky Geological Survey(KGS) was established in 1854 as the official geologic research organization in the Commonwealth. Since that time the Survey has performed basic research in a number of geologic areas such as energy, applied geology, mineral resources, geologic mapping, and hydrogeology. Because of coal's importance to Kentucky, a significant part of the geologic data collected by the KGS is coal related. Coal-related data also occur in a variety of other KGS data sets such as the petroleum and water data files. To adequately respond to coal-related inquiries, the KGS maintains an inter- active, on-line data base in which various types of geologic and hydrologic information can be easily stored, retrieved, and manipulated. The KGS will continue to expand and update this data base through ongoing research, and by cooperating with the Kentucky Natural Resources and Environmental Protection Cabinet, Kentucky Department of Mines and Minerals, U. S. Geological Survey, and University of Kentucky Institute for Mining and Minerals Research. Data in this comprehensive system is available to State, Federal, and local governments; industry; researchers; and the general public. These data facilitate coal exploration, mine planning and permitting, coal production, and research activities in the Commonwealth of Kentucky.

Jan 1, 1983

Plans for the fall meeting of the AIME, to be held in conjunction with the Centennial of Engineering -marking the 100th anniversary of the Society of Civil Engineers-indicate that the Chicago gathering will be one of the most significant in Institute history. Headquarters for the six divisions represented will be the Palmer House. Twenty technical sessions will be held from September 3 to 6, with papers of industry-wide impact to be presented. The papers will follow the theme of the celebration-a century of engineering progress. The MBD will start the ball rolling with morning and afternoon sessions Thursday, September 4. A luncheon also will be held. MBD has scheduled morning and afternoon sessions for the following day as well. MGGD, Iron and Steel, and the Coal Div., will hold sessions Friday afternoon. The Industrial Minerals Div. plans an executive meeting, 5 pm, Friday. Geology Subdivision is slated for morning and afternoon sessions Saturday. The Coal Div. will meet again Saturday morning.

Jan 1, 1952

By N. A. DeCecco, H. M. Meyer

IN the early stages of a titanium brazing investigation, binary titanium systems partially or completely known and fundamental metallurgical data were surveyed to select the pure metal most likely to be satisfactory for producing a ductile high strength joint. The phase diagrams for the purpose of this survey were classified into two groups: 1—systems with large solubility in ß titanium, but negligible solubility in a titanium, and 2—systems with large solubility in a titanium. Those metals with melting points believed to be too high or too low for titanium brazing (Tim = 1730°C) were eliminated from consideration. The melting points of vanadium, tungsten, tantalum, hafnium, zirconium, and the platinum group are too high and those of zinc, lead, cadmium, and tin are too low. The remaining metals were grouped as follows: 1—large ß solubility: Cr,¹ Mn,² Fe;³ CO,4 Ni,5 Cu,6 Be,' Si." —large a solubility: Al.9

Jan 1, 1954

By P. Somasundaran, D. R. Nagaraj

This study initiated to explore the potential of commercial chelating extractant for beneficiation of minerals revealed "LIX "65N to be an excellent collector for cuprite and chrysocolla. The collector action of the LIX is proposed to result from its chelation with copper species on the surface of the minerals. Thus, the syn-isomer of LIX65N, which is unable to form a chelate with copper ions, failed also to act as a collector. The proposed mechanism takes into account partitioning of LIX between the mineral surface (to form a surface chelate) and the copper chelate dispersed in the bulk aqueous phase (either due to formation of the chelate with dissolved copper, or due to detachment of chelate formed at surface). The efficiency of the collection is dependent upon this partitioning since the bulk chelate is found unable to collect. The marked decrease in flotation obtained when copper was added to the system supports this mechanism. The dependence of flotation of chrysocolla and cuprite on pH and reagentizing time is discussed on the basis of the proposed mechanism. Batch laboratory flotation tests using synthetic mixtures of oxide, sulfide and mixed oxide-sulfide copper minerals with quartz demonstrated the ability of LIX to separate the copper minerals from quartz.

Jan 1, 1980

By Sukeyuki Mori, Kinjiro Aso, Tsuyoshi Hara, Hisao Okamoto

A theoretical calculation of the electro-osmotic circulation of liquid in a rectangular micro-electro-phoresis cell was presented by Smoluchowski (1921) and Komagata (1933). According to their theories, the velocity of liquid changes with depth such that the velocity distribution may be represented by a symmetrical parabola in the cell. Their theories appear contrary to the results of our experiments which show that the velocity distribution curve is represented by a symmetrical parabola whose symmetrical axis is displaced from the center line of the cell. A similar phenomenon had been suggested by Lane and White in 1937 based on the latter's theory which seemingly was incomplete. By using methods of measuring electrophoretic velocities based on the above three theories, serious errors are obvious. We are thus proposing a unified theory for determining the electrophoretic velocity of mineral particles in a rectangular cell. The equations of Smoluchowski, Komagata and White can be derived from our theory as special cases. On the basis of our theory, we are proposing an improved method of determining the precise electrophoretic velocity of mineral particles based solely on the coefficients of the velocity distribution curve. In our experiments, this method gives satisfactory results. We determined the relation between the zeta-potential and pH value of suspension for several minerals.

Jan 1, 1980

By Alexander B. Morris

In a recent paper on the intermittent injection of gas in gas-lift operations as opposed to continuous injection, Morgan Walker presented a comparative table showing the effect on oil and gas production from the same wells under the two methods of operation.' This table carried a column showing the formational gas-oil ratios under each method, computed by deducting the volume of input gas from the volume of trap gas. During the entire spring and summer of 1928, the present writer had been engaged on some extensive test car tests of rich gas in Glenpool, seeking, primarily, for an explanation of the apparent loss of gasoline during the summer season between the field meters and the plant master meter. Tests at several of the field meters where the richest gas was obtained regularly failed to check with other tests on the same gas made farther along the line, and the difference was not made up by the quantity of drip gasoline collected between the points. In the course of these tests, the final outcome of which is immaterial to the present purpose, an attempt was made to construct a curve representing the relationship between gasoline content of the gas in gallons per thousand cubic feet and the shrinkage in the volume of gas treated as a result of removing the condensible fractions. Such a curve was made, expressed in units of gallons per thousand cubic feet on the abcissa and the ratio vapor volume to liquid volume on the ordinate. This curve is a rectangular hyperbola and shows that 3 gal. of gasoline taken from 1000 cu. ft. of raw gas as a vapor occupied much less space, per gallon, than did 1 gal. of gasoline taken from 1000 cu. ft. of another sample of gas. This is, in general, corroborated by converting to the same units the residue settlement curves prepared by the Tidal Oil Co. and by the Natural Gasoline Manufacturers Assn., though the three curves, when plotted together, occupy entirely different positions on the paper, as shown in Fig. 1. The bearing of all this on Mr. Walker's discussion of gas-lift is this: if the formational gas is to be computed by deducting the input gas from the trap gas, some correction must be made for the vapor volume

Jan 1, 1930

By James Norman, O. C. Ralston, John Dasher

MOST mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chromite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficiation, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put in the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separation, at a density of 4,0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabromethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in, size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. EARLIER WORK It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the

Jan 1, 1942

By G. K. Zaharlev

With a productive output growing at an annual rate of 8%, the Soviet mining industry should emerge as the world's leader in total mineral output during the 1980's. (The Soviet Union's share in the world's total mineral output in 1973 was estimated at 22 to 23%.) According to estimates by Soviet mining experts, the mineral potential of the Soviet Union will sustain the current 8% annual growth rate in the future.

Jan 12, 1974

By Wm. I. Weisman, C. W. Tandy

Consumption of fluorspar in the United States in the last ten years has doubled to 1.34 million tons. One main, reason for the increase has been the use of the basic oxygen furnace to produce steel which requires considerably more fluorspar than the open hearth. The increasing consumption of aluminum and fluorocarbon chemicals will require more fluorspar, Since 1964 domestic fluorspar prices have advanced over 70%. Maximum prices were attained in 1971 and remain stable. These higher prices have brought about the expansion of production capacity at many of the present mines and mills. Exploration has been intensified, resulting in new discoveries, which are being brought into production. Many deposits, heretofore considered uneconomical, are being reappraised for possible development. Companies who have not previously mined fluorspar are actively seeking and acquiring new properties. The outlook for the continued health of the domestic fluorspar industries is favorable at present prices; however, it is doubtful that production will be greatly increased. New production will have to come from presently inaccessible areas of much greater distance from consuming centers. Prices will have to be higher to support this production. Domestic fluorspar production meets only 20% of domestic consumption. Thus, reliance on imports on fluorspar in the future will become increasingly more critical.

Jan 1, 1975

By A. N. Khayyat, R. G. Temple, R. Skelton

The fluid energy mill has been in use since the 1930's when an early patent was granted to N.H. Andrews in the USA. The microniser design has been basically unaltered since that date and current designs such as the Airfilco "Micronizer" have been progressively developed from results based on wide experience. The authors have been engaged in a research programme to establish optimum design and operational parameters for the Micronizer so as to provide a more quantitative basis for scale-up prediction of results. An introductory section will first trace the development of fluid energy milling including reference to other designs which have developed alongside the micronizer (especially the “Jet-o-miser"). With regard to design features the number of fluid injection nozzles and their size was investigated to establish the optimum range. Injection angle and, the consequent diameter of the internal "tangential circle" was carefully studied to determine the effect of this parameter on product size. The research was carried out using fine limestone as the test material with air as the grinding medium. Feed size fractions of 0-120µm, 0-250µm, 0-500µm, and 300-600µm were milled and product size analyses were carried out using the Coulter Counter technique.

Jan 1, 1980

A small group of members of the Institute headed by W. H. Shockley, has insistently demanded that the Institute submit to the members for letter ballot the question of our using in our publications and corre-spondence certain so-called "simplified spellings." The principal argu-ment in favor of this proposal is written by Mr. Shockley and will be submitted in full to the membership for ballot. It rests chiefly on the desirability of saving the time of school children in the learning of the spelling of the English language. A sample of correspondence had with one of the gentlemen on this subject is given herewith in order that members may see what the correspondence and publications of the Institute would look like if we adopted the proposals. This sample was chosen at random: "Onse I condemd the report ov a president of the Institute. He did not pruve his case even on paper-"a hot air profet," I sed. Time has pruved he was." "I rote yu about the muvement to better the spelling in the Institute Bulletin, etc., neglecting to say some things that I mite hav said and things hav happened since which no member ov a democratically governed society shoud stand without protest."

Jan 12, 1919

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker's reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By C. S. Land

Relative permeability functions are developed for both two- and three-phase systems with the saturation changes in the imbibition direction. An empirical relation between residual nonwetting-phase saturation after water imbibition and initial nonwetting-phase saturations is found from published data. From this empirical relation, expressions are obtained for trapped and mobile nonwetting-phase saturations which are used in connection with established theory relating relative permeability to pore-size distribution. The resulting equations yield relative permeability as a function of saturation having characteristics believed to be representative of real systems. The relative permeability of water - wet rocks for both two- and three - phase systems, with the saturation change in the imbibition direction, may be obtained by this method after properly selecting two rock properties: the residual nonwetting-phase saturation after the complete imbibition cycle, and the capillary pressure curve. INTRODUCTION Relative permeability is a function of saturation history as well as of saturation. This fact was first pointed out for two-phase flow by Geffen et al. 1 and by Osaba et a1.2 Hysteresis in the relative permeability-saturation relation also has been reported for three-phase systems.3 Since saturations may change simultaneously in two directions in a three-phase system, four possible relationships arise between relative permeability and saturation for a water-wet system. The four saturation histories of this system were given by snel14 as 11, ID, DI and DD. I and D refer to the direction of saturation change (imbibition and drainage), with the first letter of the symbol indicating the direction of change of the water phase. As used in this paper, the second letter of the symbol refers to the direction of saturation change of the gas phase, i.e., D and I indicate an increase and decrease, respectively, in gas saturation. Only a few three-phase relative permeability curves have been published. Leverett and Lewis5 published three-phase curves for unconsolidated sand, and Snell4 reported results of several English authors for both drairrage and imbibition three-phase relative permeability of unconsolidated sands. Three-phase relative permeability curves for a consolidated sand were published by Caudle et a1.3 for increasing water and gas saturations (ID). Corey et a1.6 reported drainage (DD) three-phase relative permeability for consolidated sands. Recently, Donaldson and Dean7 and Sarem8 calculated three-phase relative permeability curves from displacement data on consolidated sands, also for saturation changes in the drainage direction. The only published three-phase relative permeability curves for consolidated sands with saturation changes in the imbibition direction (11) are those of Naar and Wygal.9 These curves are based on a theoretical study of the model of Wyllie and Gardner 10 as modified by Naar and Henderson.11 Interest in three-phase relative permeability has increased recently due to the introduction of new recovery methods and refinements in calculation procedures brought about by the use of large-scale digital computers. The scarcity of empirical relations for three-phase flow, and the experimental difficulty encountered in obtaining such data, have made the theoretical approach to this problem attractive. RELATIVE PERMEABILITY AS A FUNCTION OF PORE-SIZE DISTRIBUTION Purcell used pore sizes obtained from mercury-injection capillary pressure data to calculate the permeability of porous solids.12 Burdine extended the theory by developing a relative permeability-pore size distribution relation containing the correct tortuosity term.13 The works of Purcell and Burdine were combined by Corey14 into a form that has

Jan 1, 1969

By J. R. Ross, J. B. Rosenbaum

Bureau of Mines research has resulted in the development of fluid- bed ion-exchange columns for recovering uranium from slime pulps. In pilot plant tests, slime slurries containing up to 6 percent solids were processed at flow rates of 10 gallons per square foot per minute with high uranium recoveries and efficient resin loadings. Uranium was effectively eluted in a laboratory fluid-bed elution column at eluate-to-resin ratios of less than 5:1 and eluate flow rates of 3 gallons per square foot per minute. Construction costs of mills using these improved ion exchange techniques are estimated to be 25 percent less than for mills using solvent extraction of clear solutions. For mills having a capacity of 2,000 to 2,500 tons of ore per day, the saving would be in the range of $2.5 million. In addition, a saving of about $0.80 per ton of ore in total operating costs is indicated.

Jan 1, 1973

By G. Thodos, E. M. Phillips

A reduced density correlation for the gaseous and liquid regions of ethane has been developed from all the experimental PVT data available in the literature for this substance. Saturated vapor and liquid densities reported for methane, propane and n-butane were utilized to establish the rectilinear-diameter line for ethane. This line was then used with the saturated-vapor data for ethane to produce the saturated envelope for this substance. Most of the saturated liquid data reported for ethane were found to be inconsistent with the saturated-liquid curve resulting from this study. The correlation covers the regions 0.65 < TR <6.0 and 0 < PR < 15. For regions for which no experimental data have been reported, the isobars of the correlation were extended by the use of the theorem of corresponding states. This correlation is presented both on rectilinear and log-log coordinates. INTRODUCTION At the present time, there is considerable interest in the exact PVT behavior of pure hydrocarbons. Matschke and Thodos12 recently have developed a comprehensive compilation of experimental vapor and liquid density data for methane. Similar studies have been conducted for other pure substances.4, 7 In the present study the density data available in the literature for gaseous and liquid ethane have been critically reviewed and utilized to develop a reduced density correlation for this substance. SATURATED LIQUID AND VAPOR DENSITIES The rectilinear-diameter rule proposed by Cailletet and Mathias5 states that the sum of the saturated liquid and vapor densities of a pure substance is a linear function of temperature which passes through the critical point. This law, although empirical, has been well established by continued verification since its conception in 1886. This rule has been applied to the saturated density data of methane,6 propane 17 and n-butane8 to produce the straight lines presented in Fig. 1 which pass through the critical point TR = 1.00, Pr = 2.00. The rectilinear-diameter relationship for ethane was established from the lines for the other substances in Fig. 1 by plotting the quantity p~, + PR against zc for different reduced temperatures. A critical analysis of the saturated vapor and liquid densities reported for ethane by Kuenen,10 Maass and McIntosh,11 and Sage, Webster and Lacey18 revealed that the values of PR1 + pr resulting from these studies were inconsistent with the rectilinear-diameter line obtained from the reliable density data of the other substances, as shown in Fig. 1. In the analysis of these data, reduced quantities were calculated using the critical con-