Search Documents

By Fred Porter

Pollution problems from smelters may be unique in industry since the pollutants cover the wide range of SOx, particulates, carcinogens (arsenic), plus a number of heavy metals, the health implications of which are not clearly understood. In addition to this wide range of pollutants, many of the plants are extremely old; and fugitive emissions may, in fact, be the most significant air pollution problem. The Environmental Protection Agency, both in an in-house and contract effort, has assessed the quantity of pollutants emitted and evaluated the health impact. This paper will review the status of EPA's regulatory efforts in both new and existing smelters in light of these pollutant assessment studies.

Jan 1, 1976

By Hobart M. Kraner

THE mineralogy of blast furnace sinter is of interest because its mineral content is one of the important factors contributing to its character. There are so many other factors affecting the properties of the sinter, however, that it is well to mention them here. The proportion and character of the raw materials, that is, raw ores, concentrates, returns, and fuel, as well as the mixing and the water content, all have a marked effect on the physical properties of the product and the degree to which sintering action can be carried on. The process of sintering is a relatively fast operation. In as much as appreciable time is required to carry on processes of fusion in such masses of low thermal conductivity, large lumps of hematite ore frequently remain unfused and partly unchanged in state of oxidation in the sintering process. The kind, the grain size, and the amount of fuel used affect both the completeness of the fluxing reaction and the prevailing atmosphere. The rate of reduction in laboratory tests is not only dependent upon the state of oxidation of the sinter but also upon the sizing and porosity. Atmosphere and temperature affect the state of oxidation of the iron oxide, and the atmosphere alone may determine the ferrous minerals that finally develop. The rate and extent of cooling, the type of coolant, the subsequent handling, and screening all have serious effects upon the type of sinter that eventually enters blast furnace bins. The degree to which actual fusion or fluxing takes place in the sintering operation has a marked effect upon density. A sinter which has been extensively fused by high content of fuel in the batch will no doubt have a higher weight on the bulk basis than one which had a lower fuel content. As high temperatures are required to do this job, the iron oxide under these conditions will be largely magnetite. Sintering at low temperatures to produce larger proportions of hematite means a decrease in the amount of liquid formed and a much more sensitive bonding process. In this case the liquid must be distributed more uniformly and thereby used more efficiently than would be the case where higher temperatures were permitted to prevail more or less indiscriminately. Where coarse ore particles are used in a sinter mix it is not expected that any particles coarser than 1/4-in. can be fused and incorporated in the system to such an extent that the gangue contained within these lumps will have been converted or fused by the sintering process. It is for this reason that coarse ore, returns, or both, in a sinter usually result in a sinter which breaks easily and at the same time may contain some of the original minerals of the lump, such as quartz and hematite. In examination of sinters at Bethlehem Steel Co. minerals such as quartz and corundum have been found, none of which are considered normal associ- ates of wustite or magnetite. Some degree of heterogeneity or lack of equilibrium is not unusual in the sintering process. The differences in specific gravity between hematite and magnetite might be ample reason for poor strength in a not very well sintered mass containing coarse particles of. ore or returns. The shrinkage taking place in a lump of hematite in its conversion to magnetite by temperature and/or atmosphere is appreciable. Sintering of ores as it is carried out is crude chemistry, for the grain size is relatively coarse, the application of heat is certainly not uniform, and the time factor is inadequate for other than partial completion of reactions. Coarse lumps of coke or coal cause local heating around these centers, and fuel which is too fine may result in such slow burning that sufficiently high temperatures are not always obtained. High temperatures are essential to the work required. The Swedish practice of sintering is established on the basis of producing an easily reducible product high in hematite. This is achieved through uniformity of grain size in the sinter mix and close control of the temperature through careful regulation of fuel and sintering rates. This produces a sinter which is very tough in character and which has a high degree of porosity. Although the hematite content is not produced upon cooling by drawing air through the mass, there would be greater possibility of accomplishing this reaction with this type of sinter than is the case in American practice. In the latter, the temperatures are so high that temperature alone converts most of the mass to magnetite. The grains are so coarse in the final product that together with the fluxed condition it would be difficult to reoxidize them to hematite upon cooling. An examination of the iron-oxygen diagram' shows that hematite does not exist above 2651°F. It also shows that there is no liquid in the pure magnetite-hematite system until 2881°F is reached. On the other hand, in the system magnetite-wustite liquids exist at considerably lower temperatures than this. It will be seen, therefore, considering only the iron oxides, that the bonding action obtained in America in sinters comes about through considerable temperature and/or reducing conditions that produce compositions containing even less oxygen than is contained in magnetite or than results from the fusion of silicates. The bonding obtained from the iron oxides is encouraged by the reducing conditions that prevail in the vicinity of the fuel particles in a mass of this sort, where temperatures are above 2600°F. As magnetite and wustite are opaque, they do not lend themselves to petrographic study by transmitted polarized light. The silicates found in sinter and the glass that has not crystallized transmit light and can be studied by these methods in which indices of refraction and other optical properties of anisotropic crystals lead to their definite identification. The index of refraction is the only property that can be measured in glass under the microscope, and this is a clue to its probable approximate composition.

Jan 1, 1954

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By Elmer W., Pehrson

NOT much serious consideration was liven to the military aspects of raw materials before World War 1. Following the outbreak of war in Europe in 1914, however. this situation was promptly changed. Disruption of allied shipping and German submarine warfare soon cut off a substantial part of the material the United Staten was accustomed to receiving from overseas. At the same time, raw material requirements rose rapidly as the tempo of industrial preparedness was stepped up in anticipation of war. By April 1917, when we entered the war, serious shortages threatened and consideralde attention was being given to our "deficcient" raw materials. The term "war mineral," began to appear after we became active combatants. But there is no evidence that "strategics" and "critical." as now used, had entered the lexicon of our raw materials experts during the last war nor were there apparently any officially recog¬nized list or definitions of what con¬stituted war materials. According to G. A. Roush in his book, `'Strategic Mineral Supplies," C. K. Leith, while serving as mineral advisor to the War Industries Board. compiled the first unofficial list of deficient minerals in 1917.

Jan 1, 1944

By Warren L. Howes

THIS paper deals primarily with an investigation of ball-mill liners that was conducted by the writer over a period of six years at the Mammoth mill in Arizona. The investigation covered a wide variety of designs of liners in both primary and secondary mills. The comparative results are presented herein as evidence of the extent to which design influenced liner life and mill performance. FLOWSHEET The feed to the Mammoth mill was a complex, oxidized, gold-silver-lead-molybdenum-vanadium ore with rhyolite, andesite and granite as gangue. Although the ore varied between stopes, the long-term average in character remained substantially the same. Capacity was 560 tons per day. [t] Fig. I shows an abbreviated flowsheet of the grinding section of the mill. PRIMARY BALL MILL A 3-ft. Symons shorthead crusher in open circuit crushed to ¼ -in. maximum one-way dimension the feed to the 5 by 10-ft. Marcy open-end ball mill. The mill rotated at 80 per cent of critical speed and was charged with 4-in. forged steel balls. Cast balls were used for a few months at a slight reduction in ball cost, but breakage of the large balls reduced the ball size and grinding capacity to a point where the over-all costs suffered out of proportion to the saving in cost of balls. For metallurgical reasons, the finished product of the mill was maintained at minus 8-mesh. This coarse product, plus the very abrasive ore and the absence of fines in the feed, caused abnormally rapid wear of the mill liners. The resultant high operating cost led to the most extensive phase of the investigation. [ ] In order to clarify the difference in design of the various types of liners used, Fig. 2 shows the profiles with the arrangement in which grinding balls of maximum size would lie on the face of the liners. The results with each type of shell liner in the primary mill are shown in Table I.

Jan 1, 1943

By J. Mackintosh Bell

In the numerous districts subsidiary to Cobalt, and carrying mineral deposits similar in character to that world-famous mining camp, the most interesting recent developments have occurred in South Lorrain. The district, the center of which lies about 16 miles southeast of Cobalt, was the scene of a rush in 1907 but, in spite of the success of the Wett-lauffer mine, the locality soon lost its popularity, largely on account of the unsavory early history of the Keeley mine. In recent years, following the successful development of this property by the London operators, who acquired it from the liquidator of the original company, and the later conspicuous progress made on the properties of the Mining Corporation contiguous to the Keeley on the north, the district has again come into prominence and, at present, is doing much toward maintaining the gradually declining production of Cobalt itself. Apart from the Mining Corporation of Canada and the Keeley Silver Mines Limited, the principal concerns now operating in South Lorrain are the Lorrain Consolidated, the Trout Lake Mines (operated by English interests associated with the Mining Corporation) and the Canadian Lorrain Silver Mines (operated by the Huronian Belt Co., of London). A number of minor prospects are also active. The Wettlaufer and Currie, on both of which considerable work was done some years ago, are now closed. TOPOGRAPHY AND GENERAL GEOLOGY The topography of the South Lorrain area is rather more rugged than that of the vicinity of Cobalt, but the local relief, relatively speaking, is not great. Numerous lakes and streams lend a certain picturesqueness to a landscape, which is not entirely marred by the absence, from the valleys and hillsides, of the splendid bush that formerly clothed them but which has been swept away by forest fires. The geology of the locality is simple, in a lithological sense, but rather complicated structurally. The oldest rocks are Keewatin greenstones

Jan 1, 1924

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method.

Jan 8, 1950

By T. F. Baily

During the period of the war, in both this country and Canada, a number of attempts were made to make pig iron from steel scrap in the electric furnace, and a considerable tonnage of white pig iron was produced, the silicon and manganese additions being made with ferroalloys; but it is believed that the experiments conducted. at Canton, Ohio, in

Jan 1, 1930

By O. B. Hopkins

As prefatory to the body of this paper, a few general statements will be made (1) in regard to the history and importance of the asbestos, (2) as to the principal sources of the raw material, and (3) as to the types and modes of the occurrence of asbestos.

Jan 1, 1915

By W. B. Mather

THE object of this paper is to record and interpret data collected during the examination of over 250 barite deposits in the Central Mineral District of Missouri. [ ] In the course of this study, the origin of the deposits, which the author believes to be hydrothermal, has been given particular attention. Economic barite deposits occur in two main areas in Missouri: (I) in the Washington County District of Southeast Missouri, from which over go pct of the state's production is derived; and (2) in the Central Mineral District, which includes portions of 15 counties in Central Missouri (Fig I). Barite in the smaller Washington County District is mined from widespread low grade, relatively shallow residual deposits, whereas in the Central District, it is mined

Jan 1, 1947

By Carl S. Westerberg

1,. C. McCABE*-—An increased derliand for coal in the west is to be expected because of the growth in population and industry during the past ten years. The author calls attention to the increased mechanical cleaning of Utah coal between 1938, when no cleaning was being done, and 194.7, when more than 24 pct of the production was cleaned. This is essentially the Period of most rapid growth of the Pacific Coast. area altliough the growth and, no doubt, the general trends in coal production and cleaning continued at a less accelerated rate during 1948. The Pacific southwest increased 37 pct in population between 1940 and 191.7 while the United States showed only a 7 pct increase in the same period. it has been estimated that there will be an additional 15 pct increase in population between 1947 and 1950. The conclusion that more coal and more mechanicak cleaning capacity will be required appears to be well founded. Mr. Westerberg discusses the cco- nomic advantages of coal cleaning reflected in freight savings, in lower cost per million Btu, and lowered ash and sulphur content. In view of the limited occurrence of coking coals in the west it would be interesting to know whether significant beneficiation in coking strength can be expected from mechanical cleaning of Utah coals. This has been demonstrated for some eastern and midwestern coals. One can readily agree to the desirability of recovering the fine coal that has heretofore been lost in washery slurry. The very cheapness of coal has Iridered

Jan 1, 1950

By A. E. Outerbridge

I had the honor to present to the American Institute of Mining Engineers at the Pittsburg meeting, February, 1896, a paper having the foregoing title, in which I said : " It has generally been accepted as a fact that cast-iron, under the influence of repeated shocks, becomes brittle, and will finally break under a blow which otherwise it would have withstood. It will probably surprise metallurgists, therefore, to learn that experiment disproves the supposed fact, and establishes exactly its opposite. " The result of about a thousand tests of bars of cast-iron of all grades, from the softest foundry mixtures to the strongest car-wheel metal, enables me to assert with confidence that, within limits, cast-iron is materially strengthened by subjection to repeated shocks or blows." Three tables were appended showing increase of strength

Jan 1, 1905

By Frank Wilder

THE most important process in a gypsum mill is calcining the crude mineral. There seems, however, to be little progress or change in calcining methods. This would not be surprising if the industry was not, in other ways, developing. The demand for gypsum in its various forms, however, is growing rapidly. The output has more than doubled in six years, while the value of gypsum products, through the introduction of higher priced specialties like wall board, has nearly trebled in the same period. In other industries, under somewhat similar conditions, calcining in rotating cylinders, either by direct or indirect heat, has replaced the method that still prevails in gypsum mills. Efforts were made to use rotary calciners in manufacturing plaster of Paris in the early days of the industry in America; 25 years ago rotary calciners were in use in Germany. At that time there was great diversity of opinion in regard to their merit. In 1923, the output of calcined gypsum in the United States was 3,101,378 tons. About nine-tenths of this material was calcined in kettles, the remainder in rotary calciners. The ratio was about the same 10 years ago. During these 10 years, rotary calcining made rela-tively no gains, and there were no important changes in the construction of kettles. In their manipulation, the only change of consequence was in connection with the length of time that the gypsum is left in the kettle. For wall-plaster purposes, all producers who had not previously done so changed from second-settled to first-settled calcined gypsum, thereby reducing production costs and improving the plasticity and sand-carrying capacity of their plaster. Nevertheless, in the few mills in which they were installed, rotary calciners continue to operate, with possibly one or two exceptions, and to be highly successful. In these 10 years, the Cummer type of rotary calciner has disappeared. All rotaries now used are of the cement-mill type with a diameter of 6 or 7 ft. and length of 80 to 120 feet.

Jan 2, 1925

By S. Yamaguchi

IN this study of thorium and uranium minerals an x-ray shadow microscope of the Cosslett type1 was used. A flux of electrons driven with a voltage

Jan 1, 1959

By E. V. Watts

The D-7 zone of the Ventura Avenue field is of special interest because the initial reservoir pressure at 92.00 ft nearly equaled the pressure exerted by the overburden. While the phenomenon has been observed elsewhere in the world, there is no record of a previous case in California. Such high pressures have been attributed to sealing of the reservoir, followed either by emergence of the beds or by compaction of the sediments in various ways. Oil in the D-7 zone is undersaturated. At pressures above the bubble point, oil is recovered by the slight expansibility of the reservoir framework and its liquid contents. More than 40 pct as much oil probably will be recovered by this mechanism as will be recovered by internal gas drive after pressures pass below the bubble point. Operations are handicapped by sand and pipe troubles. Introduction The Ventura Avenue field has been under development since 1915. It has long been considered a "high-pressure" field, but interest was heightened by the extreme conditions encountered in the recent development of the so-called D-7 zone. The original reservoir pressure in this pool is estimated to have been 8300 psi at a depth of 9000 ft below sea level, or 9200± ft below the surface. A fluid pressure approaching that exerted by the overlying sediments has been encountered in other parts of the world, but never before in California to the degree observed in the D-7 pool. With few exceptions, the original pressure in California fields is about equivalent to the static head of water below the water table in the outcrop. Structure The Ventura anticline is a prominent feature of the Ventura basin, being traceable on the surface about 17 miles.' The Ventura Avenue field is at the apex of the anticline. It is about one mile wide and five miles long, the major axis lying in an east-west direction. The productive limits cover an area of about 2300 acres. The entire anticline has been severely folded and faulted. The productive portions in particular are broken up by three major thrust faults having a general east-west strike. The resultant four fault blocks are termed the A, B, C, and D blocks, respectively. Certain electric-log intervals are assigned numbers. Fig I is a diagrammatic north-south section of the field near the crest, looking west, and shows three of the four fault blocks. To the west, the upper fault divides into two branches, which define the B block. Wells penetrating a fault may duplicate over 1000 ft of formation. However, the greater fault movement is the strike shift, which is believed to exceed 2500 ft both between the A and C blocks and between the C and D blocks. The location of water is irregular and unpredictable. A few intermediate waters exist, while some strata have more than 2000 ft of productive closure.

Jan 1, 1948

By E. V. Watts

The D-7 zone of the Ventura Avenue field is of special interest because the initial reservoir pressure at 92.00 ft nearly equaled the pressure exerted by the overburden. While the phenomenon has been observed elsewhere in the world, there is no record of a previous case in California. Such high pressures have been attributed to sealing of the reservoir, followed either by emergence of the beds or by compaction of the sediments in various ways. Oil in the D-7 zone is undersaturated. At pressures above the bubble point, oil is recovered by the slight expansibility of the reservoir framework and its liquid contents. More than 40 pct as much oil probably will be recovered by this mechanism as will be recovered by internal gas drive after pressures pass below the bubble point. Operations are handicapped by sand and pipe troubles. Introduction The Ventura Avenue field has been under development since 1915. It has long been considered a "high-pressure" field, but interest was heightened by the extreme conditions encountered in the recent development of the so-called D-7 zone. The original reservoir pressure in this pool is estimated to have been 8300 psi at a depth of 9000 ft below sea level, or 9200± ft below the surface. A fluid pressure approaching that exerted by the overlying sediments has been encountered in other parts of the world, but never before in California to the degree observed in the D-7 pool. With few exceptions, the original pressure in California fields is about equivalent to the static head of water below the water table in the outcrop. Structure The Ventura anticline is a prominent feature of the Ventura basin, being traceable on the surface about 17 miles.' The Ventura Avenue field is at the apex of the anticline. It is about one mile wide and five miles long, the major axis lying in an east-west direction. The productive limits cover an area of about 2300 acres. The entire anticline has been severely folded and faulted. The productive portions in particular are broken up by three major thrust faults having a general east-west strike. The resultant four fault blocks are termed the A, B, C, and D blocks, respectively. Certain electric-log intervals are assigned numbers. Fig I is a diagrammatic north-south section of the field near the crest, looking west, and shows three of the four fault blocks. To the west, the upper fault divides into two branches, which define the B block. Wells penetrating a fault may duplicate over 1000 ft of formation. However, the greater fault movement is the strike shift, which is believed to exceed 2500 ft both between the A and C blocks and between the C and D blocks. The location of water is irregular and unpredictable. A few intermediate waters exist, while some strata have more than 2000 ft of productive closure.

Jan 1, 1948

By W. W. Roepke

One phase of Bureau of Mines research deals with reduction of primly respirable dust generated by bit cutting action at a coal seam face. This paper presents a summary of coal cutting technology addressing this problem. All aspects of the cutting system affecting miner health and safety are discussed. Cutting design concepts are considered that minimize dust generation, energy used, and Ignitions, while maintaining production. With present equipment, an operator can maintain production and minimize dust energy and conditions by cutting at maximum depth (maximum sumping or advance rate) at all times, at minimum rpm with fewest possible bits, and with lowest possible included bit tip angle, i.e., minimum bit wear.

Jan 1, 1985

By H. H. Lowry

SCIENCE attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as applied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on dis-coveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the opposite. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accom-plished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 6.1 to 8.3 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in, the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

Jan 1, 1968

By W. A. Naismith, R. T. Pakalnis

The Umgal a section of the We1gedacht Exploration Company Ltd., a member of the Rand Mines Group, is situated near Utrecht in the province of Natal, South Africa. Two coal seams, the Alfred and Gus, are mined to fulfill commitments to both inland and export markets. To increase extraction in the high quality Alfred Seam, pillar extraction, known locally as stooping, was introduced to the mine in September, 1980. Mining is a conventional cut-drill -blast operation and takes place under a unique set of geological conditions viz. moderately thick seam at 3.5 m; rapidly varying cover from 25m to 120 m; an overburden containing competent sandstone and dolerite horizons. In order to improve the understanding of the manner in which the pillar and overburden interact during pillar extraction, a largely visual system of monitoring backed up by roof-floor convergence measurements was employed. Preliminary analysis of the observations suggests that roof collapse or goafing occurs in three phases but is only initiated once a critical amount of convergence has taken place.

Jan 1, 1983