Search Documents

By P. E. Landolt

BEFORE World War I, and even prior to World War II, lithium was considered among the rare elements. Mining was limited to exploitation of a few well selected sources of rich minerals recoverable by hand cobbing methods. Within the past five years the situation has changed radically. Many new sources have been explored and developed, principally in Canada, North Carolina, and Southern Rhodesia. The prime raw material for lithium recovery is spodumene. In Southern Rhodesia, however, both petalite, a modified spodumene, and lepidolite, a lithium mica, are being mined in quantity.

Jan 4, 1957

By J. A. Corbyn

An analysts of mining investment from the point of view of financial optimization is presented. The method uses differential equations to describe financial performance rather than the more usual method of modeling mine accounts from year to year. The analysis shows there is a optimum mine life that can be easily determined if certain simplifications are made. Tables are given to facilitate computation of the optimum life.

Jan 1, 1985

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending north-easterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 724 per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrothermal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons.

Jan 1, 1955

Jan 1, 1920

By L. M. Cathles, H. R. Spedden, E. E. Malouf

Fluid flow through an igneous rock formation will occur mainly through fractures. A non-diffusing or slowly diffusing tracer (such as .5µ silica spheres identifiable under electron microscope) will arrive at a monitor well when enough fluid has been injected to displace the volume of water in the flow fractures between the injection and monitor wells. A rapidly diffusing tracer (such as NaC1)-will diffuse into the matrix blocks and so a volume of tracer nearly equal to the total fluid volume contained in the rock formation between injection and monitor wells must be injected before significant diffusing tracer arrival will be noted. The flow fracture porosity is typically one hundred times smaller than the total porosity of an igneous formation. The shift between diffusing and non diffusing tracer arrivals, together with the diffusional characteristics of the tracers, can define the diffusional accessibility of the matrix blocks of an igneous formation. A field test of these concepts and the problems encountered will be described.

Jan 1, 1974

By John T. Awald

The Bradshaw Mountains of west-central Arizona cover an area of 1600 square miles and contain numerous old mines and prospects. The area has been geochemically sampled on a reconnaissance basis to relate mineralized areas to regional structure and rock types. Copper analyses of stream sediments have been classified and contoured to show the distribution of low and high backgrounds and low, intermediate, and highly anomalous areas. Contoured results are compared to geology and known mines. Several prospecting areas are indicated.

Jan 1, 1972

By Rollin Farmin

"SWELLING GROUND" delivers pressure on mine timbers that originates in expansion of the wall rock, whereas "heavy ground" delivers only gravitative pressure. Of the several possible causes considered, the swelling is attributed to the physical surface action of water on gouge and flaky rocks at the periphery of the mine opening.

Jan 1, 1944

NOW continuing with the preparation of the moulds I say that it is necessary to give the greatest attention to the differences of the clays as well as to the differences of those things that you wish to mould; and to know that every concavity in the mould produces a convexity and every convexity a hollow following the shape of the original pattern that you have. The pattern should be a body of a harder mated than the thing [78] you wish to mould with and of a substance that is not swollen or disintegrated by moisture. Its archetype may be of marble, bronze, lead, or any other metal, or also of wood, wax, tallow, gypsum, sulphur, or other plaster compositions-in short, of whatever you may have or whatever succeeds best for you, depending on whether the works are large or small and easy or &cult to mould. If you wish to cast them in bronze, you must mould them with loam, covering them with it and then drying it. There are some things in which it is enough to form only one part, such as half- or bas-reliefs. These are easy if they have no undercuts. Some other patterns that are easily handled are formed in two halves, or in three or four pieces, if they are of a hard material. There are also moulds for large statues, which, if one desires to make them of bronze, are first made of wax according to the ordinary procedure. I have in mind to describe every one of these processes in their own place. There are like- wise some moulds that are difficult to make, like scenes on a plane to which figures in full relief are attached, or twisted ornaments or other detached things that cannot be withdrawn from the mould without break-

Jan 1, 1942

By Alexandre Mitinsky

The theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,l that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably due to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually assumed, though incorrectly, that the proportional limit is determined by the ultimate strength. In Germany the poin't at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining the elastic limit by alternately loading and unloading the test specimen is a lengthy process and time has in itself a very considerable influence on the results of physical tests.

Jan 1, 1916

By T. W. Lippert

CUBA fancies herself the "pearl of the Antilles" and, by many, Jamaica is called "blessed." But far to the southward lies what is seemingly the Caribbean's most glittering jewel, the sparsely-settled, Spanish-speaking United States of Venezuela, indeed blessed by nature to a lavish degree. Not a large country, Venezuela is leaping from the donkey to the airplane under the impact of its natural wonders. Angel Falls, dwarfing Niagara and seldom seen by man, is hidden in the cold, primitive and unexplored Guiana highlands along the southeast border. A few hundred miles northwest are the low and torrid coastal plains from which gush unlimited black-gold streams of oil. About midway are the Llanos-low-lying, savanna-type grasslands, beneath which large deposits of bauxite are as yet barely touched by the explorer's diamond drill. And jutting starkly upward 2000 ft from a surrounding expanse of savanna is a small mountain (see front cover), 11 miles long and 1 mile wide. It is, or was, La Parida.

Jan 2, 1950

By E. I. Larsen, A. S. Doty, F. R. Hensel

The alloy under discussion is a Pig. I shows results of heat-treating tests nickel-silicon bronze and is one of many on two typical nickel-silicon bronze castings age-hardening or precipitation-hardening of the type on which the observations were copper-base alloys. The hardening constituent is a nickel-silicon compound.l The quenching temperature necessary to produce hardening by a subsequent aging treatment is a function of the composition and extends from about 700°C. to 950°C.; the aging temperature range extends from 4000 to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of: 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Sj: balance. comer. made. A quenching temperature of 750°C. produces almost as high a hardness on subsequent aging as do quenching temperatures of 850' and 900°C. Several foundries have spent years of active and intelligent effort in trying to control the casting and heat-treating variables of nickel-silicon bronzes and finally gave up the attempts because of the inconsistencies of results.2 This undesirable characteristic was not manifest in the ultimate hardness or conductivity but primarily in tensile strength and ductility, as shown in Table I. The variation in tensile properties was often much greater than that existing on the alloys

Jan 1, 1941

By A. S. Doty, E. I. Larsen, F. R. Hensel

The alloy under discussion is a Pig. I shows results of heat-treating tests nickel-silicon bronze and is one of many on two typical nickel-silicon bronze castings age-hardening or precipitation-hardening of the type on which the observations were copper-base alloys. The hardening constituent is a nickel-silicon compound.l The quenching temperature necessary to produce hardening by a subsequent aging treatment is a function of the composition and extends from about 700°C. to 950°C.; the aging temperature range extends from 4000 to 600°C. The work carried out by the authors of this paper was confined to cast alloys having compositions within the ranges of: 1.5 to 3.00 per cent Ni; 0.4 to 0.75 per cent Sj: balance. comer. made. A quenching temperature of 750°C. produces almost as high a hardness on subsequent aging as do quenching temperatures of 850' and 900°C. Several foundries have spent years of active and intelligent effort in trying to control the casting and heat-treating variables of nickel-silicon bronzes and finally gave up the attempts because of the inconsistencies of results.2 This undesirable characteristic was not manifest in the ultimate hardness or conductivity but primarily in tensile strength and ductility, as shown in Table I. The variation in tensile properties was often much greater than that existing on the alloys

Jan 1, 1941

By Walter Knox, J. D. Doherty

IN 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. SUMMARY OF RESULTS Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3). 2. The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 1 1.6 per cent to 19.2 per cent. There was a noticeable segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may he a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance I. The removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. With intermittent operation the burning rate was almost always less than the feeding rate. The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. I3). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). GUIDING PRINCIPLES In planning the investigations, the following principles were adopted: Selection of Healing Equipment.-Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By T. F. Baily

DURING the period of the War, in both this country and Canada, a number of attempts were made to make pig iron from steel scrap in the FIG. 1.-EXPERIMENTAL FURNACE. 5000 KW. CAPACITY: 150 TONS 2 PER CENT. SILICON PIG IRON PER DAY. electric furnace, and a considerable tonnage of white pig iron was produced, the silicon and manganese additions being made with ferroalloys; but it is believed that the experiments conducted at Canton, Ohio, in

Jan 1, 1930

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

THE comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined.1,2 These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. COMPOSITION AND FABRICATION OF ALLOYS The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing [ ] from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys will be referred to hereafter by their nominal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedures calculated to produce sheet 1/16 in. thick, cold-reduced by 20, 40, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from l00° to 1500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By Axel Hultgren

IN ingots of silicon-killed carbon steel made without addition of - aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially. In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents arid, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,10,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis17 and their amount to increase from the top downward in the axial region .2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form," by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.15 Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19,20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping' or of refractory material from various sources1,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistance to hydrofluoric acid, imparted by the alumina content. Silicate inclusions, are often referred to as. the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1948

Jan 1, 1920

By A. M. Gow

The trend in ball milling has been toward mills of larger diameter, but without fundamental laws as a guide. The speeds at which mills are run have been a matter of cut-and-try. This paper deals with both diameter and speed and proposes to show the laws which apply to some laboratory ball mills, ranging in diameter from 18 to 42 in., run at various speeds. The correlation of power, speed and grinding rate of the respective mills will be shown by curves of markedly significant similarity. Before presenting the results some consideration will be given to the mechanics of ball milling. Mechanics and Theory of Ball Milling As early as 1904, Herman Fischerl reported observations on specially constructed ball mills which allowed the paths of balls to be studied. The following conclusions were drawn: 1. Balls do not grind the ore, but crush it by impact. 2. At slow speeds the balls roll down the inclined heap, but at higher speeds the balls close to the wall adhere to it until they reach a certain height, whence they are thrown through an arc to the bottom. 3. The falling balls do not come down in clusters, but in series, the balls of each row keeping to their own line of flight according to their distances from the wall while ascending. 4. A further increase in speed results in the balls adhering during the whole of the circuit to the side of the drum. (This centrifuging speed may be called the "critical" speed and may be taken as a reference basis, since it is a constant function of the diameter.)2

Jan 1, 1930

To Americans, Alaska occupies a unique position, both geographically and historically. The only integral portion of the United States lying in the sub-Arctic and Arctic regions of the Earth, the early remoteness and climatic conditions effectively combined to impede the economic development of this area. Although Alaska has been a part of our Nation since 1867, its mining industry is still at that stage of development which characterized the West 100 years ago when miners concentrated on high-grade lodes and rich placer deposits. Since World War II, however, there has been a noticeable increase of interest in the raw materials of the North. This concern has been most noticeable in Canada, Scandinavia and Russia, but it has been, and is being shown in Alaska. To the American mining industry, the potential importance of this State can be summed up by the question, "Can Alaskan mining compete successfully with those of other states and countries?" The answer revolves about the vital factors of geography, economics, and the political turmoil of the World. These aspects are among those discussed on the following pages in a series of articles by Alaskans and non-Alaskans alike. We invite you to read "Alaska: Regional Report."

Jan 12, 1961