Search Documents

By W. Bonfield

A study has been made of the dislocation substructures produced in hot-pressed beryllium specimens strained to various levels in the range from 800 x 10-6 In. pev in. to fracture. A number of distinctive dislocation configurations were observed in this region which had not been noted at lower levels of strain. These included dislocation-dislocation interactions to form networks, dislocation "walls", subgrain boundaries and complex arrays, interactions between dislocations and large beryllium oxide particles, and the generation of dislocations from certain particles. The nature of these differences in substructure and their relation to the stress-strain characteristics of polycrystalline beryllium are discussed. In a previous study1 of the plasticity of commercial-purity, hot-pressed beryllium a transition was found in the deformation characteristics in the mi-crostrain region. The initial plastic deformation could be represented by a parabolic stress-strain equation, but above a critical stress there was a complete departure from this relation and a reduction in the strain-hardening rate. The dislocation configurations produced by various levels of micro-strain in this region were examined by transmission electron microscopy and a general correlation was established between the observed transition in deformation characteristics and the dislocation structure of the material. The two stages in the micro-strain region distinguished in these experiments were designated as Stage A' and Stage B'. Stage A' type deformation generally was noted up to a plastic strain of -80 x 10"6 in. per in. and Stage B' type from -80 x 10-6 to -800 x 10'6 in. per in. The discovery of two stages in the microstrain region naturally posed pertinent questions as to the existence of any further distinct stages in the subsequent plastic deformation. The purpose of this paper is to present a study of the dislocation configurations produced in similar beryllium specimens strained to various levels in the range from -800 x 10 in. per in. to fracture and to discuss the relation between substructure and the stress-strain characteristics. It is concluded that this region of strain can be considered as a distinct stage in the plastic deformation of polycrystalline beryllium. Tensile specimens of gage length 1 in. and cross section 0.18 by 0.06 in. were prepared from commercial-purity, hot-pressed QMV beryllium and then annealed at 1100°C for 2 hr. 2 followed by a careful chemical polishing procedure.3 The specimens were strained at a constant rate to various levels of strain in the range from -800 x 10-6 in. per in. to fracture (at 0.5 to 2 pct elongation), using the Tuckerman strain-gage technique1 to measure plastic and total strain. Thin foils were obtained from the strained and fractured specimens by chemical polishing3 and were examined using an RCA-EMU 3 electron microscope. Considerable care waS taken to avoid both accidental deformation during the preparation of the thin foils and excessive heating during their examination. Selected-area diffraction patterns were determined for each micrograph. Tilting experiments were also performed whenever appropriate to establish the dislocation zero-contrast position and hence determine the Burgers vector. This operation was sometimes not possible due to the rapid contamination of the foils which occurred in the electron microscope. RESULTS AND DISCUSSION To enable the distinctions between the dislocation arrays at high and low strain levels to be adequately made, the main characteristics of Stage A' and Stage B' deformation are briefly reviewed. 1) Stage A'. In the annealed starting condition there was a variable density (5 x 107 to 3 x 10' cm per cu cm) of isolated dislocations within a grain. The initial deformation in a tensile specimen was heterogeneous, with the dislocation density increasing in a few grains to 5 x 10g to 1.5 x 101° cm per cu cm. The deformation occurred exclusively on the basal plane by the movement of one or more 1/3 (1130) type dislocation systems. The dislocations were long and regular in form and nearly all the intersections exhibited a simple four-point node configuration. No interactions between glide dislocations and beryllium oxide particles were observed. 2) Stage B. In Stage B' there was a large increase in the number of grains exhibiting dislocation movement and also a change in the nature of the deformation, in which jogged dislocations and elongated loops became the characteristic feature. The splitting up of the elongated loops into smaller loops and the possibility of source action from the re-

Jan 1, 1965

By Norman Lamont

The evaluation of certain reser-voir properties, such as porosity and fluid saturation, from electrical well surveys has been widely accepted in petroleum engineering. Various investigators have established relationships between these properties and certain parameters which affect the response of the electrical log. Among these are the resistivities of the mud, its filtrate, and its filter cake. In 1949, Patnode1 established a relationship between the resistivities of the mud and filtrate. The well logging service companies have contributed relationships for the mud-mud cake resistivities2,3 These have been valuable since it was the practice to measure only resistivity of mud at the well site. During the mid-1940's the industry began drilling wells with oil-emulsion drilling fluids. These were conventional aqueous muds with a dispersed oil phase. Since 1950, oil-emulsion muds have been used on an increasing number of wells each year. However, the practice of measuring only the resistivity of the mud at the well site has continued, and the mud filtrate and mud cake resistivities have been determined by the above-mentioned relationships. Service companies are now equipped to measure all three resistivities at the well site. An investigation was conducted on the resistivities of oil-emulsion muds, mud filtrates, and mud cakes to determine if these values conformed to the relationships for aqueous muds. TYPES OF MUDS Fifty-one oil-emulsion mud samples were prepared in the laboratory following a standard manual' published by a leading mud company. The diesel oil in the samples varied from 5 to 50 per cent, the majority of the samples being in the 10 per cent region. The basic aqueous mud types which were converted to oil-emulsion muds were commercial clay and bentonite muds, low pH and high pH, caustic-quebracho treated muds, and lime treated muds. The emulsions were stabilized by dispersed solids, lignins, lignosulfo-nates, sodium carboxymethyl cellulose, or sulfonated petrolatum. It is worthy of note that after a quiescent period of two weeks at room temperature all samples, regardless of emulsifying agent, remained stable. The make-up water for the muds was from the laboratory tap. Resistivities were varied by the addition of table salt to the water. A range of mud resistivities from 0.44 to 3.9 ohm-m was obtained in this way. Twenty-three field muds were tested. These covered the same range of mud types as did laboratory muds. Oil provinces of the Gulf Coast, South Texas, West Texas, Oklahoma, Montana, and Canada were represented. MUD TEST PROCEDURE Each mud was tested for density, viscosity, pH, and filter loss by standard testing techniques. The resistivity measurements were obtained with a Schlumberger EMT meter. This meter required small volumes of sample, e.g., 2 mm. Filtrate was obtained from a Standard Baroid fil-ter press at the end of a 30-minute test. The filter cake from the same test was used for cake resistivity measurements. Mud, filtrate, and cake samples were heated to 100" F in a constant temperature water bath prior to measurement of resistivities. RESULTS The relation between mud resistivity (Rm) and mud filtrate resistivity (Rmf) is shown in Fig. 1. The solid line represents an average for the data. The equation of this line is Rmf =0.876 (Rm) 1.075 . . (1) Arbitrary limits, indicated by the dashed curves, have been set. The majority of the data falls within these limits, but some points do lie outside the limits. The approximate equation Rmt = 0.88 Rm , . . . . (2) will give satisfactory results within these limits. The data on mud cake resistivity Rmc is shown in Fig. 2. The solid line is an average for the data. The equation for the line is Rmc = 1.306 (Rm)0.88 The dashed lines are arbitrary limits on the data. Within these limits, Eq. 3 may be simplified to Rmc = 1.31 Rm . . . . (4) DISCUSSION The limiting curves in Figs. 1 and 2 represent maximum deviations of ±25 per cent. Thus the use of the average curves can introduce considerable error. There is no substitute for accurate measurements of mud, mud cake, and mud filtrate resistivities at the well site. The mud sample tested should be representative of the mud opposite the formation being logged. The average mud filtrate resistivity curve of Fig. 1 is reproduced in Fig. 3 with two curves which have been published for clay-base aqueous muds2,3. The latter curves were determined from average values of a large number of drilling fluids. The three curves have essentially the same slope and the differences between them are from 7 to 22 per cent. Comparison is made only to illustrate the possibility of error

Jan 1, 1958

Jan 1, 1970

By J. A. Barr

Tennessee phosphates are commercially divided into three varieties: Brown, Blue, and White.

Jan 1, 1915

By Frederik P. Agterberg

This paper deals with frequency distributions in the field of mineral resource evaluation when a grid is superimposed on the study area and metallogenetically significant attributes are coded with respect to the cells of the grid. It is shown that the parameters of a negative binomial distribution for frequency of mineral deposits per cell can be derived from the parameters of a gamma distribution for the coded attributes. It is also shown that an exponential model for spatial correlation of cell values and Matheron's discrete Gaussian model for indirect transfer functions may provide a suitable methodology for relating cell value distribution to cell size.

Jan 1, 1977

By R. S. Dean

BLUE HEAT PHENOMENA IN constructing a theory of the flow and hardening of metals, we necessarily make use of such phenomena as seem to be, universally observed in metals. It is, therefore, a matter of. concern to the constructors of such mnemonic systems if one or two of the group classified as metals show anomalous behavior. Such egregious phenomena are observed in pure or nearly-pure iron in the reaction of its mechanical properties to low-temperature annealing after cold work and to increased temperature of testing. In short it has been generally observed that iron," as an outstanding exception among metals, increases its hardness and strength by low-temperature annealing. after cold work,1 and also by increase of testing temperature to the range of 150° to 300° C. The investigation here recorded was made then with the object of ascertaining if similar phenomena were observed in high purity iron and, if not, to the presence of which impurities these phenomena could be traced.

Jan 1, 1929

By Charles W. Goodale

The ores of the Butte district present a variety of combinations, and their treatment by concentration is an interesting study. They may be classified in general as follows: 1. Copper-silver ores, which are produced by the mines of the Anaconda group, and by the Mountain View, Colusa, Silver Bow and Parrot. The high-grade ores from these properties are roasted and then smelted; but a large proportion of the output is low-grade and siliceous, and hence requires concentration. The copper-bearing minerals are chalcocite, bornite, enargite and chalcopyrite, in varying proportions in the different mines, the gangue, which breaks readily into grains, being quartz and feldspar. 2. Silver-copper ores, of which the Gagnon vein is the largest producer. The grade of the ores from this mine is such that nine-tenths of the output requires concentration. The silver- and copper-bearing minerals of this vein are massive wurtzite, sphalerite, bornite, chalcopyrite, pyrite, tetrahedrite, enargite, tennantite and galenite, with a quartz gangue associated with feldspar and small quantities of barite and fluorite. The gangue is very hard and not at all granular. 3. Silver-ores containing a small amount of gold, embracing the product of the Alice, Magna Charta and Moulton claims, on what is known as the Rainbow lode, and that of the Lexington, Blue Bird, Nettie, Burlington and other mines. The gangue is quartz, carrying pyrite, sphalerite, galenite, tetrahedrite and argentite, with manganese in the form of rhodochrosite and rhodonite. Good results on ores of this class cannot be obtained by concentration, because large percentages of the silver-bearing minerals are disseminated through the gangue in such minute grains that even the finest practicable crushing

Jan 1, 1897

By D. Y. F. Lai, R. J. Borg

Tracer diffusion of Fe59 has been measured in the a-stabilized Fe-1.8 at. pet V alloy from 700° to 1500°C. The activation energies are obtained in both the presence and absence of magnetic order. Furthermore, it is established that diffusion in the alloy is identical to that in pure iron and consequently the values of Do and Q accurately represent the temperature dependence for self-diffusion. The purpose of this investigation is to obtain an accurate estimate of the temperature dependence for self-diffusion in bee iron in both the presence and absence of magnetic order, and, in so doing, to establish the temperature range of the magnetic effect.&apos;" As the temperature interval suitable for diffusion measurements is severely limited in both bee phases of pure iron because of the intervening fee ? phase, the experiments were performed on an a-stabilized alloy containing 1.8 at. pet V. This alloy is bee over the entire range from room temperature to the melting point. Although there have been several independent investigations of self-diffusion of iron in a, iron,1, 3-6 there still exists considerable disagreement regarding the values of Do and Q for the paramagnetic region. The two systematic studies of diffusion in 6 iron6, 7 previously reported are also only in fair agreement; but in view of the extremely small temperature range available for diffusion studies, i.e., 1390o to 1535oC, this is not surprising. It is comparatively easy to obtain accurate values of Do and Q for the a-stabilized alloy inasmuch as measurements can be made over the entire temperature range -700o to 1500°C. However, in order to assume that these same values apply to pure iron requires careful comparison of the data in the a, and 6 regions in both the alloy and pure iron. We have made several measurements in the appropriate temperature ranges and are unable to establish any systematic difference between the diffusion coefficients of iron in pure iron and in the alloy. We therefore conclude that the values obtained for the alloy are truly applicable to pure iron; the complete evidence favoring this conclusion will be discussed later in this paper. EXPERIMENTAL The experimental methods will be given here only in barest detail since they have been thoroughly de- scribed elsewhere.l, 7 The alloy was prepared by induction melting and chill casting under argon. Diffusion samples were machined from the ingot and annealed in hydrogen for several days at 900°C to give an average grain diameter of 1 to 2 mm. The penetration profiles of the tracer were established by a sectioning technique, the residual activity being counted after the removal of each section. The tracer used is Fe59 which emits two high-energy ? rays of 1.098 and 1.289 Mev, respectively; these were detected by a ? scintillation counter equipped with a pulse-height analyzer. For the measurements in the temperature range -700o to 1130°C the samples were vapor-plated with Fe59, encapsulated in quartz under vacuo, and annealed in resistance-heated furnaces which are controlled to ±1°C. The specimens diffused at higher temperatures are prepared as edge-welded couples, the two halves being separated by a thin washer of the alloy to prevent sintering. The diffusion anneal is then carried out by inductive heating under a dynamic vacuum. The temperature is monitored pyrometrically. RESULTS The diffusion coefficients are obtained from the penetration profiles in the usual way using the error-function complement relationship. The results over the entire temperature range are shown in Fig. 1. In the linear region, 900o < t > 1500°C the least mean squares (lms) values of the diffusion coefficients are given by D = 1.39 exp[-(56.5 ± 1) x 103/Rt] cm2/sec [l] The average departure of the measured diffusion coefficients from the values given by Eq. [1]In order to determine whether or not the slope is truly constant over the entire range from 900" to 1500°C, the data are arbitrarily divided into two groups, the first containing values between -900" and 1133°C and the second between -1133o and 1500°C. The lms values for the two groups are given by Eqs. [2] and [3]: D = 0.519 exp[-55.7 x 103 /RT](900° to 1133°C) cm2/sec [2] D = 1.45 exp[-56.7x103/RT] (1133° to 1500=C) cm2/sec [3] Thus, there is no significant difference between the high- and low-temperature segments of the linear region. This not only assures us of the consistency of the values obtained by induction heating as compared to those obtained from the resistance-heated

Jan 1, 1965

By M. I. Sherman, J. D. H. Strickland

USE of a hydrometallurgical approach to the oxidation of sulfide ores and extraction of metals therefrom may have advantages over the more common smelting techniques when a low grade deposit is difficult to concentrate or the subsequent separation of metals, coexisting in the ore, is laborious by any known smelting operation. For economic reasons, the most promising oxidants are either atmospheric oxygen or electric power. The use of oxygen, or air under pressure, has recently been revised. Pyrrhotite has been converted to iron oxide and elementary sulfur&apos; and a variety of sulfides have been treated by Forward and co-workers.2-4 Generally sulfate is the end form of the sulfur but with galena in an acid medium, elementary sulfur can be formed." For economic reasons chlorine and ferric iron salts are about the only possible alternatives to the atmosphere as oxidizing agents for base metal sulfides. If aqueous solutions of chlorine or ferric iron are employed, the reduction products can be oxidized electrolytically in situ and used again, thus acting as catalysts for electric power as oxidant. The use of ferric salts for this purpose is established hydrometallurgical practicea but, although chlorine gas has been employed in the dry state at an elevated temperature, its use in aqueous solution at or near room temperature has not found favor. The reaction of chlorine water with the soluble sulfide ion has been studied by several workers,7-9 and both sulfate and elemental sulfur are found as end products, the latter being favored by the presence of a low concentration of oxidant relative to that of sulfide in solutions of about pH 9 to 10. Of direct bearing on the work in hand are an early American patent" and a recent Austrian patent." The former advocates stirring powdered ore with an aqueous solution of ferric chloride chlorine oxides and chlorine. In the latter it is claimed that both metal and sulfur can be obtained by electrolysis, in a diaphragm cell, of a metal ore slurry in brine. Details in these patents are scant and no data or explanation is given for the mechanism of the reaction which, in the Austrian work, is attributed to the (unlikely) action of nascent chlorine at the anode surface. No mention is made of possible differences in behaviour between various ores. Apparatus A complication encountered when working with chlorine water is that a serious loss of chlorine occurs by gas partitioning unless an enclosed system is used and any air space in the apparatus is kept very small and constant. Arrangements were made, therefore, to take out samples for analysis without letting air into the system to replace the liquid removed. For convenience in studying a heterogeneous reaction the apparatus was so designed that a reproducible controlled stirring rate could be maintained and the ratio of surface area of ore to volume of solution was approximately constant throughout any experiment. The apparatus used is shown in Fig. 1. The ground ore was placed in the horizontal cylindrical vessel, A, of about 1 liter capacity, heated by a constant temperature circulating bath pumping water through the concentric jacket, B. By adding chro-mate to this water, an ultraviolet radiation filter effectively surrounded the reaction vessel, greatly reducing any possible photochemical decomposition of chlorine solutions. Stirring was effected by glass paddles, C, attached by an axle to a magnet which was rotated by another powerful Alnico magnet, D, outside the glass end, this magnet being itself rotated by an electric motor electronically controlled to constant speed. Speed could be varied from about 150 to 900 rpm and was measured and held to within 1 pct of a given value. The end of the reaction vessel remote from the stirring magnet was closed by another one-ended glass cylinder, E, connected by thin polyethylene bellows, F, clamped by screw clamps and watertight rubber gaskets to the main vessel. Through E, a glass electrode and calomel electrode projected into the solution and a hypodermic syringe pierced a small bung and allowed acid or alkaline to be added to maintain a constant pH. By pushing the fully extended bellows until the two cylinders touched, from 50 to 100 ml of solution could be forced out through a sintered disk into the three-way tap system, G, either to waste (for flushing purposes) or up into a 10 ml burette where the solution could subsequently be measured out for analysis. The ore samples were introduced at H, the tube being stoppered by a thermometer of —1 to +52ºC range, graduated to 0.1°C intervals. To prevent ore from being ground in the end bearings of the stirrer these bearings were pro-

Jan 1, 1958

By J. B. Wagstaff, R. A. Buchanan, J. F. Elliott

High speed photography through blast-furnace tuyeres showed coke particles moving rapidly. Model studies showed a raceway was formed and gave quantitative results which were correlated with actual blast furnaces. Another study showed the similarity between hanging and the flooding of a packed column. This was explored by models. THE combustion zone before the tuyere in an iron blast furnace is a vital region because here are generated: 1—most of the gases on which the furnace depends to carry out its basic operation of reducing iron ore to the metallic state, and 2—the major fraction of the heat required in the nearby regions of the furnace for the various reduction reactions, the fusion of the slag, and the melting of the iron. Since the greater part of the coke is consumed in this region, the descent of the burden must be greatly affected by the characteristics of the tuyere zone. This region then would seem to be a profitable field for study. Fortunately, a view into this important zone is available to the operator through the tuyere peep sight. Here he sees relatively dark pieces of coke "dancing" in the blast. What he sees is of considerable help in interpreting the behavior of the furnace at a given time but the very rapidly moving particles and the intense radiation obscures what is happening very deep in the zone. This investigation was initiated in the hope that a better understanding of the combustion region could be obtained by using a high speed camera with a maximum speed of 3000 frames per sec. It seemed the best practical method of "slowing down" this characteristically violent action within the highly luminous field. Model studies and tuyere probing also have been used to aid in explaining the observed phenomena. Above the combustion zone, but below the fusion zone, there is probably a region in which the coke is comparatively stationary. Here are zones in which the gases must flow up through the granular bed counter to descending liquid slag and metal. There is no easy way to observe this zone in a blast furnace, but model studies have been of some help in explaining the nature of the zone and the laws governing the flow of the fluids involved. The whole problem is difficult and involved and any approach to a complete solution may require long investigation. This preliminary report has been written, therefore, because it is believed that appreciable progress has already been made that would be of interest to others. Tuyere Studies, Chemistry and Kinetics It is well known from the early work of Kinney and coworkers1,2 that combustion of carbon before the tuyeres appears to occur in two zones: Zone A: C + O, = CO2; AH77°F. = — 14,108 Btu per lb of carbon [I] Zone B: CO2 + C = 2CO; H77°F = + 6,183 Btu per lb of carbon [2] Zone A (Fig. 1) is close to the tip of the tuyere and zone B is somewhat farther back; there being a transition region in which both reactions occur. It is interesting to estimate the rate at which coke is burned before a tuyere with a wind rate of 90,000 cfm in a modern furnace having 18 tuyeres. Approximately 0.55 lb of carbon is consumed by eq 1 per tuyere per sec. A like amount disappears by eq 2 for a total consumption of 1.11 Ib per sec per tuyere. Assuming the coke is 85 pct C and has a bulk density of 30 lb per cu ft, this figure can be converted to a total of 1.30 lb of coke with a bulk volume of 0.043 cu ft disappearing per sec per tuyere. At the temperatures prevailing in the combustion zone (according to Kozlovich,³ he maximum is about 3400°F), the rate at which carbon is con-

Jan 1, 1953

Aaby, Alton O , (S&apos;47) Univ of Minnesota, Mimeapolis, Minn Aaby, Waldo S , (S?48) Univ of Minnesota, Minneapolis Minn Aalde, Kaare, (S&apos;48) Univ of Nevada, Reno, Nev Aaring, Floyd D , (S&apos;48) Univ of Oklahoma, Nor man, Oka Aaronson, Hubert I , (S&apos;47) Carnegie Inst of Technology, Pittsburgh, Pa Abbott, Peyton Osborn, (S&apos;46) 1502 Westover, Austin 21, Texas Abel, Malcolm D , (S&apos;47) Univ of Texas, Austin, Texas Aberg, Richard S , (S&apos;47) Univ of Minnesota, Minneipolis, Minn Abrahamson, Guy C , (S&apos;43) 420 W Dennis St , Wilmington, Calif Abrahao, Benjamin, (S&apos;46) Escola Politeenica da Unnersidade, de Sin Piulo, Braizil Achter, Meyer R , (S&apos;46) Carnegie Inst of Tech , Pittsburgh, Pa

Jan 1, 1952

Alabama.1 Arizona 1 Arkansas 2 California 2 Colorado 7 Connecticut 8 Delaware 9 District of Columbia 9 Florida 10 Georgia 11 Idaho 11 Illinois 11 Indiana 13 Iowa 14 Kansas 14 Kentucky 14 Louisiana 15 Maine 16 Maryland 16

Jan 1, 1952

By Frank T. Weems

The basic operating properties of the DorrClone are discussed and certain metallurgical applications which exploit these properties are presented. An effective method of controlling the consistency of the DorrClone underflow is described. THIS paper presents in a general manner some of the applications of the DorrClone (Dutch States Mines cyclone) in the metallurgical and heavy chemical fields. Technical or mathematical analyses of the design factors and of the mechanism whereby the cyclone effects its separation have been capably treated in a series of previous papers.&apos;-&apos; Engineering and operational aspects of a few installations and laboratory tests have been chosen to emphasize the unique classification characteristics of the DorrClone and to illustrate its utility in certain difficult situations. Its use in coal washing and heavy-media operations are not considered. Some 25 or more industrial installations and applications of the DorrClone in the metallurgical fields are operating at present, ranging from single trial units to complete batteries composed of a multiplicity of units. The data were obtained in part from some of these, and in part from operations of units at the Westport Mill, the laboratories and testing plant of the Dorr Co. at Westport, Conn. The DorrClone was developed, in principle, by the research dept. of the State Mines, Limburg, Holland, during World War 11. Its first use was to dewater a —50 micron sand used as a dense medium in coal washing. The metallurgical wet cyclone was first publicized by Driessen and Yancey and Geer.6 ince then the cyclone has been studied as a means of de-watering, heavy media concentration, and fine size classification. The DorrClone is shown in Figs. 1 and 2. pulp to be treated is pumped through the feed nozzle, A, into the feed cylinder, B. The feed nozzle is of rectangular cross-section, the outermost edge being tangent to the feed cylinder walls. Feed shims, C, may be attached to the innermost walls to adjust the open area of the feed nozzle available to entering pulp. The tangential injection of feed under pressure supports the vortex action of the pulp that has been detained in the cyclone; the centrifugal forces of this vortex throw the coarse particles to the walls of the cone, D, where they collect and pass downward and out through the adjustable apex opening, E. The fine particles contained in most of the water that entered with the feed pulp move to the inner spiral of the vortex and flow out through the vortex finder, F, contained in the orifice plate, G, which forms the top of cyclone chamber. The overflow pulp may then spray freely into a spray chamber, H, surmounting the cyclone or pass directly into a 90&apos; elbow, I, of somewhat larger diameter than the vortex finder. Installation Where more than one cyclone is to be installed, best overall efficiency and ease of control are obtained with equal distribution of both pulp volume and weight of solids among the cyclones, and with the same pressure being maintained at each cyclone feed nozzle. Fig. 3 is a suggested arrangement for feeding two or more cyclones in parallel. Feed pressure control: Under normal operating conditions it is not unusual for some surge to exist in the feed that is to be sent to the cyclone. As will be discussed later, surges in the solids content of the pulp are usually not of great operational consequence, but surges in feed volume are a problem. Several systems have been devised for absorbing surges in feed volume, each involving a surge tank. If the surges are small and fairly rhythmical, a tank of sufficient size might be installed to dampen out

Jan 1, 1952

By Charles Meyer, Reno H. Sales

AT Butte, successive zones of sericitized and argillized quartz monzonite occur around every ore-bearing fracture regardless of its size, attitude, or relative age. The two types of alteration always occupy the same relative positions; sericite adjacent to the ore-bearing vein, clay minerals always between the sericitized rock and fresh quartz monzonite, except where overlap of alteration effects between adjacent fissures has eliminated the lower grade mineralogical products, as is the case in much of Butte&apos;s Central zone of pervasive sericitization. As long as active circulation continued in the channel, each zone migrated away from the fissure, that is, it grew at its outer edge and simultaneously receded at its veinward edge because of encroachment by the next innermost zone. The different mineralogical and chemical responses within the wall rocks to the attack by the ore fluid are dependent not on a drastic about-face change of composition of the fluid in the channel relative to its ability to alter the quartz monzonite but on continuously varying conditions of physico-chemical environment within the wall rock outwardly from the vein.

Jan 1, 1947

By T. W. Guy

DURING the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators&apos; Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, cur-dried moistures, or oven-dried moistures. For most of the reports it was necessary to esti-mate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the. products should be meas-ured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they some-times include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture.

Jan 1, 1938

By Y. C. Kim, S. L. Barua

Underground coal mine planning has traditionally focused on the mine design aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most US underground coal mines. With the enactment of the Clean Air Act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the Btu content of coal are equally important for boiler efficiency. Coal mine planning must incorporate coal quality control aspects as well as traditional safety and efficiency aspects. According to an article in Coal Age (March, 1982), nearly one-half of the US coal exported to Europe does not meet the contract specifications regarding ash, sulfur and Btu contents. Although one of the reasons cited for this problem was "inadequate sampling at the US ports," the more fundamental cause probably lies in the inadequate quality control of run-of-mine (ROM) coal at the source. To perform adequate quality control of ROM coal, mines need predicted short-term in-situ coal quality information. Such predictions are generally based on whatever available sampling information is around the mine workings. Unfortunately, the closest sampling information, in the form of diamond drill hole assays, is often several thousand feet away in most underground coal mines and is inadequate for short-term coal quality prediction purposes. This is because the diamond drill holes (DDH) were traditionally placed in the coal deposit during the mine development phase to determine coal seam continuity and overlying roof conditions. They were not placed for short- term mine planning. A study was undertaken by the University of Arizona for the Homer City Owners in Pennsylvania to show that there is a need for more closely spaced samples, if the short-term coal qualities are to be predicted with any "reasonable" degree of accuracy. Prior to this study, a short-term quality prediction model, STPM, had to be developed. This model uses not only DDH, but also other sample information obtainable during face development work to predict the qualities of in-situ coal that are available in the immediate future.

Jan 1, 1985

By J. F. Kemp

PAGE Introductory Description of Deposits of this Type,.....244 Topography of the Ducktown Region,...247 Geology and Petrography,...248 The Mineralogy of the Ores and Gangue,..249 The older minerals : Amphibole, 250 ; Pyroxene, 250; Garnet, 251; Zoisite, 252; Calcite, 258 ; Quartz, 259 ; Apatite, 259 ; Rutile, 259. The Sulphides: Pyrite, 259; Zincblende, 259; Galena, 260; Pyrrho tite, 260; Chalcopyrite, 260. Later minerals, not belonging to the Gossan: Quartz, and certain sul phides, 261 ; Graphite, 261. The Formation of the Ore,...262 The Gossan Minerals,...........263 Bibliography,............265 Introductory Description of Deposits of this Type. Ore-bodies of more or less lenticular shape and lying parallel with the foliation of schists and slates form a group of

Jan 1, 1902

By R. I. Jaffee, F. C. Holden, H. R. Ogden, A. G. Imgram

The tensile and notch tensile properties of four refractory metals (molybdenum, tungsten, niobium (columbium), and tantalum) and one alloy (Mo-0.5Ti) were investigated. All the materials were evaluated in bar form, and the molybdenum and Mo-0.5Ti also were studied in sheet form. The notch sensitivity of each material was evaluated on the basis of several criteria, including the notch-unnotch strength ratio, the ductility transition, and the fracture transitions. USE of refractory metals as structural materials in aircraft and space vehicles may subject them to low-as well as high-temperature environments. At elevated temperatures, the usefulness of a material usually is limited either by strength considerations

Jan 1, 1962

Jan 1, 1951

Jan 1, 1951