Search Documents

By Robert W. Fullerton, Donald T. King

INTRODUCTION AND THEORY by Robert W. Fullerton In coal preparation plants, as in any industrial operation where raw materials are handled, nuisance problems arising from the generation of dust are inevitable. Devices for the control or collection of dust are there- fore essential components of the plant process equipment. The general term "aerosol" is applied to small particles suspended in a gaseous medium, usually air, whose velocity under the force of gravity is small enough that the particles remain suspended for a reasonable length of time. Aerosols can be classified as dust, smokes, fumes, mists or fogs. Dust includes particles originally formed by pulverization of materials by such processes as crushing, grinding, drilling, blasting and abrasion. Smoke includes particles formed from the burning of organic materials. Fumes are particles formed by processes such as condensation and sublimation, usually at high temperatures. Mists or fogs are particles formed by the condensation of water or other vapors on some nuclei. The size of aerosol particles is generally designated in units of microns, there being 1000 microns to a millimeter and 25,400 microns to an inch. Particles of about 10 microns or above are visible to the naked eye. Table 14-1 shows size characteristics of the general classifications of particles discussed above and includes typical examples of particles commonly en- countered. Table 14-1 also shows the relationship between micron size and standard screen mesh sizes. Smoke and fume are usually in the range of 0.01 to one micron, dusts are in the range of one to 400 microns, mists are in the range of 0.1 to 100 microns, and fogs are in the range of one to 100 microns. For purposes of dust control, particles greater than 10 or 20 microns in size are considered large, particles one to 10 microns are considered fine and particles below one micron are ultrafine. Sources of Dust Because coal is relatively friable, the mining and subsequent handling operations break part of the coal into dust that can be readily carried by currents of air. In a coal preparation plant mechanical handling operations such as unloading, transferring from one belt to another, screening, cleaning, and crushing in a dry state result in the generation and release of varying amounts of additional dust. The dust problem, of course, is much less serious in plants employing entirely wet processing. In addition to dust from handling operations, thermal drying of the fine coal product frequently presents another dust collection problem. Most coal driers are

Jan 1, 1968

By G. R. Speich

The interlarnmelm spacing, growth rate, and degree of segregation that accompany cellular precipitation in four Fe-Zn alloys containing 9.7, 15.2, 23.5, and 30.5 at. pct Zn have been determined in the temperature range 400" to 600°C. The chemical free-energy change for the reaction was calculated from the available thermodynamic data and the known compositions of the phases. The fraction of the chemical free-energy change for equilibrium segregation that is converted into interfacial free energy decreases from 0.43 to 0.08 as the magnitude of this free-energy change increases from 35 to 270 cal per mole. At constant temperature the cellular growth rate is proportional to the cube of the dissipated free energy. At 600°C newly 100 pct of the equilibrium segregation is achieved during cellulm precipitation whereas at 400°C only 85 pct of the equilibrium segregation is attained. During cellular growth, mass transport of zinc occurs by grain boundary diffusion; excess zinc remaining in the a! phase after the completion of growth is removed slowly by volume diffusion. A modified Cahn theory of cellular precipitation predicts the observed interlamellar spacing within a factor of two. In cellular precipitation reactions such as pearlite formation or discontinuous precipitation, the basic problem is to predict the variation of growth rate G, interlamellar spacing S, and degree of segregation P with composition and temperature. To accomplish this we need three independent equations relating these quantities. One of these equations comes from the diffusion solution. To obtain two additional independent equations, some assumptions must be made. cahnl has suggested recently that two plausible assumptions are 1) that growth rate is proportional to the dissipated free energy and 2) that the spacing which occurs is that which maximizes the dissipated free energy. According to the first assumption, this spacing also maximizes the growth rate and the rate of decrease of free energy per unit area of cell boundary. The present work was undertaken to test these assumptions. To test the first assumption it is necessary to study a cellular reaction over a wide range of supersatura-tions to establish a relationship between G and the dissipated free energy at constant temperature. This is possible only in discontinuous precipitation reactions since in pearlite reactions constituents other than pearlite form if the composition of the parent phase deviates even slightly from the eutectoid composition. The Fe-Zn system was chosen for study because 1) discontinuous precipitation proceeds to completion over a wide temperature and concentration range, 2) the degree of segregation within the cell can be measured by lattice parameter measurements,2 and 3) the thermodynamics of this system have recently been determined by Wriedt.3 In this system the cells consisting d alternate lamellae of a and r phases form from supercooled iron-rich a phase. The a phase within the cells is bcc as is the original a phase, cia, but has a different orientation and a slightly lower zinc content than the original a phase. The r phase has a zinc content of about 70 at. pct and a crystal structure isomor-phous with T brass. EXPERIMENTAL PROCEDURE Four Fe-Zn alloys with 9.7, 15.2, 23.5, and 30.5 at. pct Zn were prepared from carbonyl-iron powder (400 mesh, 99.8 wt pct Fe) and zinc powder (200 mesh, 99.99 wt pct Zn). The powders were ball-milled together and cold-pressed under 60,000 psi to discs $ in. thick by $ in. diam. The cold-pressed discs of the alloys with 9.7 and 15.2 at. pct Zn were sealed in evacuated silica capsules and heated slowly to 1100°C over a period of 1 week (3 days at 600°C, then 3 days at 80O°C, then 1 day at 1100°C). The alloys with 23.5 and 30.5 at. pct Zn were treated similarly except that the final homogenization temperatures were 1000" and 85O°C, respectively, to prevent melting. The alloys were quenched in iced brine from the final homogenization temperature. Specimens of each alloy were subsequently aged in salt pots at temperatures of 400°, 450°, 500°, 550°, 600°, and 650°C for times that varied from a few minutes to several hundred hours. At a late stage of this work, an alloy containing 11.2 at. pct Zn was prepared by vapor-impregnation of iron foil with zinc vapor at 890°C. This alloy proved useful for electron microscope studies because it was free of porosity. The homogenization and aging conditions were based on the recent Fe-Zn phase diagram of Stadelmaier and Bridgers4 rather than the earlier diagram of ansen.5 They consist of a homogenization heat treatment in the homogeneous a field followed by an aging treatment in the two-phase a + r field. The aged specimens were metallographically polished and etched in 2 pct nital and the radius of the largest cell in the microstructure determined. This radius plotted vs time gave a straight line whose slope is the boundary migration rate or growth rate G of the cell. To determine the interlamellar spacing, specimens were examined by surface-replica and thin-section electron microscope techniques. Because of the irregular nature of the lamellae within the cell, the average interlamellar spacing S .of the cell was measured by the method of Cahn and Hagel,6 where S is defined by:

Jan 1, 1969

[Title PAGE 1 Contents Page 1 Officers and Directors5 Standing Committees 6 Professional Divisions7]

Jan 1, 1928

By J. R. Campbell

A DOZEN years or so ago, the general superintendent of our company, now the president, Mr. W. H. Clingerman, detailed me to make a study of the coal-washing problem and collect data, which threw me into contact with the best washery men of the country. and took me to those districts where the washing of coal for metallurgical purposes is carried out. I investigated many kinds of coal-cleaning schemes, made numerous tests on them, and collected voluminous data, yet I confess frankly that I have had but little practical washery experience and that little has been at the Middlefork washery of the United States Fuel Co. at Benton, Franklin Co., Ill., which was put in operation last fall. While this wash-cry installation may not be the "last word," I am quite sure it embodies some long steps in advance over older designs and constructions. From the washery man's standpoint, the removal of pyrites, or marcasite, a disulfide of iron, is the one vital problem, and the one productive of the most beneficial results, so far as elimination of sulfur is concerned. Sulfates and so-called organic sulfur occupy quite a secondary -position and are generally lost sight of in coal washing: The elimination of sulfur in coal in the past has usually been accomplished by jigging in water, but lately the use of concentrating tables has been employed with good success, and some mention may be made of the flotation process on fine coal, though hardly considered practicable. Coal washing, is rapidly coming into its own, due to the depletion of low-sulfur coals for coking purposes, and before many years we predict as careful attention being given to the design and construction of coal washeries, ,as is now being given to byproduct plants and other allied industries. Heretofore, coal washing has been considered only as an incidental and a necessary evil-instead of the big problem it is one worthy of the most careful study by men well trained along technical lines and capable of delving into the fundamental principles.

Jan 9, 1919

By G. R. Leverant, C. P. Sullivan

Re crystallized TD-nickel mi-2Th0,) in both coated und uncoated conditions was fatigued at 1800°F at total strain ranges varying .from 0.2 to 0.75 pct. The fatigue life of uncoated inaferal, Nf, was related to the total strain range, ?eT, by (2Nf/021AeT = 0.014. A duplex Al-Cr pack coating increased the fatigue life by about a factor of two. The cracks that led to failure in both coated and uncoated material were initiated at the outer surface, indicating that the mechanical properties of the surface layers were important in determining fatigue life. Crack propagation and subsurface crack initiation in the TD-nickel occurred preferentially at grain boundaries with cavitation at thoria particle-matrix interfaces an integral part of the grain boundary fracture process. The importance of both the grain morphology developed during thermome chanical processing of TD-nickel and the distribution of thoria particle sizes to fatigue resistance are discussed. THE fatigue properties of only a few dispersion-strengthened metals have been studied at temperatures 0.5 Tm;1,2 among these have been lead and aluminum containing oxide dispersions. TD-nickel is a material of interest for application in aircraft gas turbine engines, but little fundamental information is available on its behavior under cyclic loading conditions. In this study, the low-cycle fatigue properties of TD-nickel were determined at 1800°F with emphasis on the 101-lowing; 1) the relation of the grain morphology produced during thermomechanical processing to crack initiation and propagation; 2) the role of thoria parti-cles in the fracture process; and 3) the effect of an oxidation resistant coating on fatigue life. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in. thick plate which had been subjected to a proprietary series of thermomechanical treatments with a final anneal at 2000°F for 1 hr in hydrogen. The composition of the material is given in Table I. At the test temperature of 1800°F, the 0.2 pct offset yield stress was 15,000 psi, and the elongation and reduction in area were 4.6 and 3.0 pct, respectively. The microstructure of this material has been previously described.&apos; Briefly, it consists of an array of lath-shaped grains, about 0.15 mm in thickness, with the long dimension of each grain parallel to the primary working direction, Fig. 1(a). The presence of very small annealing twirls, Fig. l(b ), together with the absence of extensive dislocation networks, Fig. L/C), indicated that the material was in the recrystal- Table I. Composition of TD-Nickel ThO2 2.3 vol pct C 0.0073 wt pct lex 0.01 wt pct Cr 0.01 wt pct Cu 0.004 wt pct S 0.001 wt pct Ti <0.001 wt pct Co <0.01 wt pct Ni bal lized condition. Commercial TD-nickel sheet has a similar grain size and shape, but unlike the present material is not recrystallized as evidenced by the absence of annealing twins and the presence of a well-developed dislocation substructure.4 The plate material had Young&apos;s moduli in the rolling direction of 22 x 106 psi and 13 x 106 psi at room temperature and 1800°F, respectively, indicating a texture with a strong {100}<001> component in agreement with previous observations on recrystallized TD-nickel sheet.596 The 2.3 vol pct of thoria particles were uniformly distributed although some clustering and stringering of larger particles was occasionally seen. The average diameter of the particles was 450 and the calculated mean planar center-to-center spacing was 2100Å. Two specimens were coated with a duplex A1-Cr pack coating. The coating was somewhat nonuniform from one position to another along the gage length. An area of the coating after testing is shown in Fig. 2. Electron microprobe analysis revealed the following zones in the various lettered regions indicated in Fig. 2: A) a bcc matrix of B-NiA1 with some chromium in solid solution along with a fine dispersion of a chromium-rich second phase which was probably precipitated during cooling from the test temperature to room temperature; B) fcc y&apos;-Ni,Al with some chromium in solid solution; C) porosity; D) a two-phase mixture of a chromium-rich solid solution containing nickel and aluminum and a small volume fraction of a nickel-rich solid solution having approximately the same composition as the immediately adjacent portion of region E, E) the TD-nickel substrate containing chromium in solid solution to a depth of 5 to 10 mils. As expected from the nature of the diffusion processes involved,7 the thoria particles were present only up to the layer of porosity, region C, Fig. 2. The measured thickness of the coating proper, zones A to D, after testing was 1 to 2 mils. The specimen design and testing techniques have been previously discussed.&apos; Stressing was axial and parallel to the lath-shaped grains (i.e., parallel to the rolling direction). The total strain range was controlled between zero and a maximum tensile strain varying from 0.2 to 0.75 pct. (The test at 0.2 pct total strain range was switched to load control at 1030 cycles at which point the peak tensile and compres-

Jan 1, 1970

By D. J. Carney, E. C. Rudolphy

IT has been demonstrated that inclusion size, distribution, and composition affect the machin-ability of resulphurized steels. Merchant and Zlatinl concluded that large sulphide inclusions aided machining by forming a (lubricating) coating on the tool face. Boulger et al.² and Van Vlack³ noted that the size, distribution, and composition of the inclusions in the steel affected the machinability. Steel specimens containing large globular sulphide inclusions usually exhibited excellent cutting properties, while machinability was adversely affected by the presence of numbers of oxide-type inclusions. Consequently a thorough knowledge of all the factors which affect the inclusions in the final product is desirable. Since almost all the inclusions have their origin in liquid steel, it was necessary to begin a study of inclusions in free-machining steels by studying the inclusions and chemical segregation in the as-cast ingot. Very little information is available on the size, distribution, shape, and composition of inclusions in large, capped, free-machining steel ingots, particularly the B1113 grade. Gregory and Whiteley4 made a general study of the inclusions in a small, high sulphur, free-machining steel ingot. Also, numerous authors have described the solidification and segregation characteristics of the four basic types of steel ingots, namely, rimmed, capped,7 semikilled,7,8 and killed7,9,10 ingots. Most of these studies were made with plain carbon or low alloy, low sulphur steel. It was desirable to study not only the ingot but also the change in size, shape, and number of inclusions on rolling an ingot to a bloom and thence to a billet. This procedure was followed and it is hoped that this study may serve the dual purpose of adding to the general knowledge of ingot solidification as well as contributing to the knowledge of the size, shape, distribution, and composition of inclusions from the ingot to the billet in a high sulphur, free-machining steel. Procedure A 12.000-lb 23x35x75 in. slab ingot of the B1113 grade was cast, sectioned, and studied both macro-scopically and microscopically. An adjacent ingot from the same heat and of the same size was rolled to a 77/8x77/8 in. bloom and thence to a 21/2x21/2 in. billet. These various bloom and billet sections were also sectioned and studied macroscopically and microscopically. Sectioning the Ingot: The ingot herein described was obtained from the United States Steel Corp.&apos;s South Works Bessemer Blow No. 0193, a B1113 mechanically capped heat. The 23x35 in. ingot (No. 2) was teemed according to normal procedures and after stripping and transportation to the rolling mill was not placed in the soaking pit but allowed to air cool in an upright position. When completely solidified, the ingot was cut into sections by means of a powder scarfing torch and further sectioned by saw cutting as indicated in Fig. 1. Cut No. 2 (1x10x12 in.) from sections A through H was cleaned thoroughly, macroetched in a solution of 50-50 water and hot muriatic acid and used to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 23-in. ingot dimension. Cuts No. 5 and 3 (lx81/2xl0 in. each) from sections A through H were treated in a similar manner to obtain a macrograph of a horizontal section from the surface to slightly beyond the center of the 35-in. ingot dimension. The composite macrograph of these horizontal ingot sections, which shows a vertical section of the ingot from top to bottom, is shown in Fig. 2. It should be noted that sections No. 2 are normal to sections 5 and 3 in the composite. Drillings for chemical analyses were obtained from selected positions within the above-mentioned ingot sections as noted in Fig. 3. The oxygen content was determined by the vacuum-fusion method. Samples for microscopic examination were cut from

Jan 1, 1954

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887 WILLIAM B POTTER 1888 RICHARD PEARCE 1889 ADAM S HEWITT 1890 JOHN BIRKINBINE 1891-1892

Jan 1, 1923

Executive SIDNEY J. JENNINGS, Chairman. GEORGE D. BARRON J. E. JOHNSON, JR. EDWIN LUDLOW ROBERT M. RAYMOND Membership KARL EILERS, Chairman LEWIS W. FRANCIS J. E. JOHNSON, JR. LOUIS D. HUNTOON ARTHUR L. WALKER Finance GEORGE D. BARRON Chairman CHARLES F. RAND BENJAMIN B. THAYER Library E. GYBBON SPILSBURY,1 Chairman ALEX C. HUMPHREYS3 GEORGE C. STONE2 J. H. JANEWAY4 BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 6, 1918

By Ralph Sweetser

THE present state of iron blast-furnace practice is metallurgical rather than mechanical; the tend-ency is toward intensity rather than toward ex-tension. The engineers have built blast furnaces big enough and strong enough, and have furnished accessory equipment ample and accurate enough for the present state of the art, but the metallurgical side has been too much neglected; the metallurgist, rather than the engi-neer, is now the man on whom the present and future progress in iron blast-furnace practice depends. The mining engineer has produced great tonnages of iron ores, and has kept ahead of the demands for quantity; now the metallurgist is improving the chemical and physical qualities of this product by ore-dressing and other forms of beneficiation. For a generation or more, the principles of mechanics have had most influence in the advancement of iron blast-furnace practice; atten-tion now is given more to the principles of metallurgy, chemistry, and ore-dressing. This metallurgical progress is taking place inside and outside the blast furnace. The two great determining factors of the inside operation are the slag, and the rate of combustibility of the coke. Outside the fur-nace, the progress is, and will be, along the lines of more careful mixing of ores and iron-bearing materials, in the sizing and washing of limestone, and in the char-acter and structure of byproduct coke.

Jan 3, 1922

By Richard D. Call

In any open pit, some slope instability can be expected, varying from bench sloughing to large-scale slope movement. Major slope displacements are preceded by small, but measurable, displacements and by other indicators of instability, such as tension cracks, rock noise, and changes in groundwater levels. A comprehensive monitoring pro- gram, capable of measuring and assimilating displacement related data, is essential for sound pit operation. The objectives of a pit slope monitoring program are 1) to maintain safe operational procedures for the protection of personnel and equipment; 2) to provide advance notice of instability so that mine plans can be modified to minimize the impact of slope displacement; and 3) to provide geotechnical information for analyzing the slope failure mechanism, for designing appropriate remedial measures, and for conducting future re-design of the slope. Surface displacement measurement using conventional survey equipment and extensometers has been the most widely used method, and it is still the most cost-effective. Tiltmeters and borehole inclinometers are also useful tools, and there are promising developments in micro- seismic monitoring. A monitoring system should have redundancy in both type and number of measurements, and be capable of rapid and effective dissemination of displacement information to those affected.

Jan 1, 1983

By Fred C. Bond

COMPRESSION TESTS THE standard method of determining the crushing resistance of rocks consists of crushing prepared shapes under slow compression, and expressing the ultimate crushing resistance at the load causing failure in pounds per square inch of crossectional area perpendicular to the crushing force, with the height approximately equal to the diameter. One-inch cubes or cylindrical drill cores are commonly used. Cubes and drill cores are cut by a high-speed steel disk with diamond dust embedded in the edges, and running under a water spray. Such a saw will cut one square inch or more of hard stone per minute. An oiled, spherical, swivel compression block of small diameter should be used to equalize the pressure. Each sample is crushed between sheets of cardboard or blotting paper extending about one-half inch beyond the edges of the stone. A cloth is wrapped around it to prevent dangerous explosive shattering. It is probably preferable to place the swivel block below the specimen, with either a rigid head or another swivel block above. Whatever the arrangement, the conditions should be selected that will develop the maximum crushing strength of the specimen, even though its top and bottom planes may not be precisely parallel. The cardboard pads may be dispensed with if the ends of the specimens are polished smooth. The use of lead pads was discontinued because of the observed tendency to split the material. The samples are weighed and measured before breaking, and the density is calculated. Cubes that contain bedding planes or veinlets are usually placed with these vertical and parallel to the crushing force, in order to develop the maximum resistance possible. A number of compression tests were made on Canadian ores, by Forrest Nagler, of the Allis-Chalmers Manufacturing Co., and are listed alphabetically in Table 1. These tests were made on one inch cubes or on diamond-drill cores approximately one inch in diameter and one inch long. The drill cores represent virgin rock, while the cubes may have been previously weakened by explosives. Compression tests have been made in the Allis-Chalmers Milwaukee Laboratory on a number of ores and other materials. These are listed alphabetically in Table 2. In test No. 1339, on limestone from the Hanna Coal Co., comparison was made between 2 by 2-in. diamond-drill core segments and one-inch cubes cut from the cores in the same strata. Results for the cylinders are tabulated directly below those for the cubes. The bedding planes were normal to the compressive force in breaking the cylinders and parallel in breaking the cubes, which accounts for the lower strength obtained from the cylinders. The percentage of net linear compression at the ultimate pressure was measured in test No. 1055 for Fontana TVA quartzite as 0.30 for cube A, and 0.37 for cube D.

Jan 1, 1946

By Lawrence H. Van Vlack, Otta K. Riegger

Periclase-type oxides were examined microscopically after being exposed to siliceous liquids. The rate of grain growth was found to be inversely proportional to the grain diameter. Grain growth proceeds more rapidly at higher temperatures, but is retarded by increasing liquid contents. aMag-nesiowiistites with higher MgO contents grow less rapidly than those with higher FeO contents. The growth rate is reduced by the presence of a second solid phase. The silica-containing liquid penetrates as a film between the individual magnesiowus tite grains. This is independent of time, temperature, amount of liquid, or the MgO/ Fe0 ratio. When present, olivine and spinel-type phases can provide a solid-to-solid &apos;&apos;bridge" between magnesioustite grains. THIS paper presents the results of a study of the microstructures of periclase type oxides in the presence of a silicate liquid. The purpose was to learn more about the effect of service factors such as 1) time, 2) temperature, and 3) liquid content upon A) grain growth, and B) liquid location among the solid grains. This study was prompted by the fact that periclase refractories are known to have very little solid-to-solid contact when the phases which are present are limited to periclase and liquid. Such a micro-structure gains industrial significance because it permits fracture during service when stresses are applied at high temperatures. The details of ceramic microstructures have not received extensive attention. This is in contrast to the extensive attention given to a) the phase relationships pertaining to refractory compositions, and b) the details of the microstructures of comparable metallic materials. A brief review will be made of the pertinent phase relationships and microstructural considerations in general, as well as of refractory compositions. a) Phase Relationships. This investigation was limited to those compositions in which (Mg, Fe)O was the solid phase. MgO and FeO form a complete series of solid solutions. Pure MgO has the name of periclase. The related FeO structure is called wustite. Both have the NaC1-type structure: however, wustite possesses a cation deficiency so that the true composition is Fe<10 even in the presence of metallic iron. The phase relationships involving solid (Mg, Fe)O and a silicate liquid are shown in Fig. 1. In this case. the liquid is saturated with (Mg, Fe)o. There-fore its SiOz content is below that encountered in orthosilicate liquids. As a consequence the liquid phase specie:; are primarily the following ions: and 0-&apos; plus occasional Fe+ ions. Two features are of importance: a) the liquid contains relatively small species and b) the liquid contains large quantities of the same species as the solid. viz., Fig. 2 shows the system, FeO-SiOz, which will be used in some of the discussions that follow. This diagram is the right side, vertical section of Fig. 1. Here, as pre\iously, the composition at the FeO end of the diagram is nonstoichiometric, varying from Feo.950 when the liquid oxide is in contact with the solid iron, to about Fe 0, when the solid oxide is in equilibrium with an atmosphere of equal proportions of CO and C02 at the solidus temperature. The Fe/O ratio will be maintained in wustite in the presence of SiO,. However, the FeM/Fe++ ratio in the liquid will be lower because of the effect OIF the SiO, on the activity of the FeO. With the addition of MgO to wustite, the over-all composition (IvZg, Fe)@, has a value of x lying between 0.9 and 1.0 when the COz/CO ratio is 1.0&apos;. b) Microstructures. In general, published attention to refractory microstructures has been directed toward the phase analyses that accompany compositional variations. This is illustrated by Harvey6 in his work on silica brick and by wells7 in his work on periclase brick. In each case, a series of altered zones is encountered which provides a sequence of phase associations. If due consideration is given to reaction kinetics, such an examination reveals phases that are compatible with equilibrium studies. Admittedly, however, it is often necessary to determine more complicated polycomponent systems to account for all the phases present.8 Relatively little attention has been given to microstructural geometry in ceramic materials. Certainly less attention has been given to this aspect of ceramic microstructures than to the size, shape, and distribution of the constituent phases in metals. Burke has pointed out that the grain size of oxides follows the same growth rules as for metals, viz.,

Jan 1, 1962

By Edwin S. Smith

Current research in the phenomenon of liquefaction has indicated some of the in situ material properties which should be considered in the planning of waste deposits. Practical experience in tailings disposal, however, must be combined with the results of theoretical and laboratory studies to develop the most economical and safe techniques against liquefaction failure. One of the many responsibilities of mining engineers and mill superintendents is providing for the safe and economic disposal of wastes (or tailings) that remain after a mineral has been extracted from an ore. The cost of disposal of these tailings exerts a considerable influence on the minimum grade of ore extracted from the mine. It varies to a great extent with each project and is dependent on many diverse factors, such as the local topographical, meteorological and seismological conditions together with the applicable water pollution laws of the area. The process used to extract a mineral from an ore determines the physical characteristics of the tailings and, thus, is one of the more important factors to be considered in the planning of disposal facilities. Today&apos;s trends in ore-processing operations complicate the problems of waste disposal: recently developed extraction methods result in the production of finer tailings, the use of lower grade ores produces greater volumes of wastes, and the enhanced land values in the vicinity of industrial plants preclude the former practice of spreading wastes laterally and force the expansion of waste deposits upwards to greater heights. The frequent occurrence of stability problems in waste deposits indicates that many mining organizations may not be employing current soil mechanics concepts and practices. One of the most spectacular, and often most disastrous, types of tailings dike failure is that resulting from liquefaction of the fine particles combined with a breach of the main retaining dike. TAILINGS DISPOSAL Since the many variations in site conditions, ore bodies and extraction processes dictate the general disposal procedures and mill superintendents incorporate special facilities to provide the most economical disposal method consistent with accepted safety standards, it is only natural that there are almost as many different disposal techniques as there are disposal areas. Methods used in the construction of retaining dikes include: (1) transporting granular material from an adjacent borrow pit and (2) mechanically segregating the total effluent and allowing the coarse fraction to form a retaining dike by hydraulic deposition. The location of a plant and the surrounding topography exert the greatest influence on the layout of tailings disposal facilities. Most of the above-ground waste deposits can be classified as side-hill, (Fig. 1,) cross-valley, (Fig. 2,) or stockpile deposits. Side-hill disposal areas are probably the most common type of layout because of the natural advantage of gravity flow, without the disadvantage of river diversion usually needed for tailings ponds formed behind cross-valley dikes. Stockpiles, which are placed on relatively level ground, require four retaining dikes and the effluent generally has to be pumped up into the disposal area. Changing production techniques or developments adjacent to disposal areas have produced variations or partial combinations of these three categories. In a series of articles, Lenhart describes many of the problems encountered in the disposal of tailings and certain innovations used to overcome them. He discusses weaknesses in design and layout and shows that disposal techniques are often learned the

Jan 1, 1970

By R. N. Dokken, J. F. Elliott

A high-temperature solution calorimeter was used to measure directly the partial molar heat of mixing of nickel in the Cu-Ni system, 0 to 15 at. pct Ni and 1200°C; of silver in the Cu-Ag system, 0 to 50 at. pct Ag and 1100°C; and of cobalt in the Cu-Co system, 0 to 6 at. pct Co and 1200°C. The heats of fusion of copper and silver were also detervnined directly. The results of these investigations are as follows: Cu-Ni: HM = [2.64 + 0.25Xm JXNiXCy kcal/g-U~OI Cu-Ag: HM =[4.00 + 0.31XAglXAgXCu kcal/g-atom Cu-Co: HF~ = [8- 5X~,]X& kcal/g-atotn Cu, AH, = 3290 * 275 cal/g-atom Ag, AH, = 2890 * 250 cal/g-atom The performance of the calorimeter was enhanced by improving the operational and control procedures, particularly the temperature-wieasuren~ent method and the solute-addition practice. The interpretation of the experimental data was improved by developing machine computational techniques that increased the speed, flexibility, and accuracy of the treatment of the data. THIS paper reports further measurements of the heats of solution of liquid metals with the high-tem- perature solution ca1orimeter.l Measurements were made of the partial molar heats of mixing in the following liquid alloys: Cu-Ni, Cu-Ag, and Cu-Co. In addition the heats of fusion of copper and silver were also determined. The apparatus and the experimental procedure were essentially those of Benz and Elliott.2 Several modifications in the experimental method and the means for interpreting the data were incorporated in this study to improve the results. The operation of the calorimeter and its characteristics will be described only briefly here. The

Jan 1, 1965

By John K. Hammes, Stanley D. Michaelson

The material presented in this chapter is supplemental information on those significant aspects of open-pit copper mining that are to an extent unique and therefore not detailed in previous sections covering the fundamentals of open-pit mine planning, operations and maintenance. In addition, tabulated cost and operating data are presented for a variety of open-pit copper mines. 13.3-1 History. The history of the civilized use of copper began at the end of the Stone Age when man discovered that the red metal, in the form of native copper, could be readily worked into a variety of weapons and tools which simplified the primitive requirements for survival. Almost concurrently, the high value of these early copper products became so widely known that they soon assumed major importance as trading commodities. Copper and copper-alloyed artifacts, even though produced in very limited quantities by ancient miners and metalworkers in a few parts of the Near East and the Western Hemisphere, were so valuable that early warriors and traders carried them into nearly all the world&apos;s known areas of importance. As far as copper is concerned, the Bronze Age, at sometime around 8000 BC to 6000 BC, marked the vague, little-known beginning of metallurgy. Man learned to alloy the valuable red metal to make it harder and tougher; its use multiplied as did the variety of weapons and tools made with the gradually increasing metallurgical and fabricating skills. By 3000 BC bronze alloy products became relatively widespread ; copper mining activities assumed tremendous importance and the mines on the Isle of Cyprus developed into prized possessions of each Mediterranean empire from the times of Egyptian supremacy to well beyond the decline of the Roman Empire.

Jan 1, 1968

By J. Moore Samuel

INTRODUCTORY BEFORE the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure, that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed "chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing the same, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 6, 1916

By I. A. Lange, A. M. Richardson

Although methods for determining shaft lining thickness are well documented, little attention has been given to the design of station breakouts and other related shaft ground support structures. This paper discusses design of selected shaft structures for the Cathedral Bluffs project, a planned 54-kt/d (60,000-stpd) oil shale mine in western Colorado. Design philosophy and construction sequences used in the three completed 520-m (1700 ft) deep, 4.6-m (15 ft) to 10.4-m (34-ft) diameter shafts are described.

Jan 1, 1984

Jan 1, 1928

By G. S. Cole, G. F. Bolling

ThE exact type of fluid flow which occurs in a solidifying ingot is important in determining subsequent grain structure. This has been shown in studies of natural Convection" and of forced stirring or other disturbances of the melt."16 We shall explicitly argue that a complement to the existing natural flow in an ingot should be more effective than other types of flow in promoting the columnar-to-equiaxed transition. The ultimate effects of fluid flow upon structure is one of the topics of solidification that we have investigated in the alloy system Pb-Sb, under conditions simulating casting. In Fig. 1, the essential features of a bidirectional growth apparatus are shown; horizontal freezing from water-cooled faces within a low-thermal-conductivity lavite boat is a reasonable simulation of an ingot section. Details such as the furnace and thermocouples are omitted in order to show the location of four permanent. magnets, each with a pole separation of 21 in. providing a central field of about 1000 Gauss. When coupled with a dc current imposed through appropriate connections made at the cooled faces, a flow of fluid is produced as shown schematically. This technique described by Pfann and ~orsi" is ideal for our purpose since the flow indicated is the same as that we observe to occur naturally in this system. Components of 99.999 pct purity were used for study and all due precautions were taken in alloy preparation to avoid contaminants. Sections of the specimens were taken to ensure results representative of the interior as well as the surface of specimens. All proportions of equiaxed and columnar regions were measured by tracing the etched grain structures onto graph paper and simply counting squares. Four alloys were examined at superheats of 40" * 5°C and 100" * 9°C. Preliminary tests had shown that no appreciable enhancement of structure was obtained with magnetic field alone, so that this condition is not reported; it should nevertheless be noted that other configurations of magnetic field will reduce convection and thus enhance columnar growth.&apos;8 For the tests reported the magnetic field was applied to a specimen by bringing the four preassembled magnets to a position 2 mm from an outer tube immediately after the ingot was poured. The dc current of 30 amps passed through the sample throughout the entire solidification cycle, resulting in a power dissipation of 9 w per sq cm of interface. This may be compared to the evolution of latent heat of approximately 18 w per sq cm. Table I contains the results of this experiment in terms of the total area ratio, equiaxed/columnar grains, as a function of the field interactions, solute concentrations, and superheats employed. The total structure of the ingot is seen to be most influenced when both the field and current are applied simultaneously; when current acts separately, little effect may be noted in spite of the heat supplied. In addition, the change in structure from the no field-no current case to the field-current condition is more pronounced at the higher superheat, and the higher the concentration of antimony. An example of the grain refinement, as well as the increased equiaxed zone, is shown in Fig. 2. It is now important to prove that there is indeed an increase in fluid flow due to the presence of the field-current interaction; this is done by temperature measurements in the liquid metal. Let us consider a bidirectional casting in which heat is applied to and removed from the system, in such a way that rate of solidification is zero.* When a sensitive thermocouple

Jan 1, 1967

By E. J. Valyi

The purpose of the continuous casting processes is twofold: As the name implies, they aim at performing a heretofore intermittent operation continuously; in this respect, they tend to satisfy the appetite of the beast that modern extrusion plants and rolling mills have grown to be. The effort invested in the development of these methods bore rich dividends in economy and in the improvement of technical characteristics. The other purpose of many continuous casting methods is to reduce the number o-f operations mushrooming between the liquid alloy and the finished mill product, essentially by substituting adequate chill in comparatively small cross sections for one or more "breakdown" steps. It is this second tendency of continuous casting that justifies description of the Soro process within the frame of our symposium: although not continuous, the Soro method constitutes a means of converting molten metal into a nearly finished mill product. The Process The name, Soro, is a composition of initials and abbreviations, with no particular technical significance. The process originates in Switzerland; it was adopted by numerous European plants between 1937 and 1940 and is now being installed in this country. It is applicable to ferrous and nonferrous alloys of an exceptionally wide range of composition. It is capable of producing rod from 1/2 in. to approxi- mately 4 in. in diameter, or other simple solid shapes of corresponding cross-sectional area. , Fig. I shows schematically the succession of operations involved. A ring is cast in a two-part centrifugal-casting metal mold. The cross section of the ring may be round, hexagonal, rectangular or some other solid shape, with the exception of any contour that is undercut with reference to the mold parting line. As cast, the ring has a riser along its inner periphery, which is removed in the next operation, so as to leave the ring with a dean cross section. Following the removal of the riser, the ring is severed at one point and one end is bent outward, leaving a slight clearance between the two ends. The next step is straightening of the ring in a special device, forming a bar with a slight bend; this is followed by any one of the conventional finishing operations that are necessary to obtain forging rod, screw-machine stock or strip. The outstanding features of this procedure are: I. The cross section cast is the same or within a few per cent of the cross section of the finished product (except for fabricating into strip and wire). 2. All operations following casting of the ring are performed cold. Equipment The equipment required is simple and inexpensive. The casting machine is a conventional horizontal-shaft mold assembly, similar to those found in centrifugal-casting foundries. Fig. 2 shows a battery of three machines- with their protecting hoods .swung open. One of these machines,

Jan 1, 1945