Search Documents

By W. A. Boyer

MINE hoisting ropes can be loaded to capacity only when the strength of each component is exactly known. Characteristic curves provide this information. When load and rate of acceleration are specified for an individual rope, the characteristic curve assumes a predetermined shape. The factor of safety, is the value drived by dividing the breaking strength of the rope by the total stress on the rope where it goes over the sheave wheel. Total stress is made up of the weight of skip and cage, weight of ore, weight of rope between sheave and rope clevise or attachment, friction load, and acceleration force. Bending stresses are neglected in this discussion, as sheaves and drum di- ameters are assumed to be large enough to reduce these stresses to a negligible value. Fig. 1 gives a family of characteristic curves for 13/8-in. improved plow steel hoisting ropes of 6 x 19 or 6x21 construction with hemp core. The curves will hold for all rope sizes of this specified quality when they are subjected to an acceleration rate of 1.608 ft per sec2. As acceleration rates of most deep shaft hoists are close to this value, this family of curves is presented as a standard. Deviation is slight for other rope sizes. Note that for 0, which is the most important, the deviation is within the width of the line on the graph. In a comparison of values for ropes of 5/8-in. and 21/4-in. diam the deviation ranges from a maximum 1.2 pct at 0 ft to 0.6 of 1 pct at 5000 ft. The value of 5.55 is the same for all ropes at 2500 ft. The tabulated columns to the left of the curves are values of total connected load for each size of rope from 5/8-in. to 21/4-in. diam inclusive. With each of these connected loads the safety factor characteristic curve for the rope will be as indicated.

Jan 1, 1957

By R. E. Ogilvie, A. R. Kaufmann, S. H. Gelles

The solid-solubility limits of iron in beryllium were determined between 850o and 1200oC by analysis of differential type multiphase diffusion couples, using an X-ray absorption technique. The maximum value of the solubility limit was found to be 0.92 ± 0.02 at. pct (5.46 wt pet) at the eutectic temperature 1225°C. The solubilities of nickel and beryllium were determined between 900°and 1200°C by the same technique and the maximum solubility was found to be 4.93 + 0.01 at. pct (25.2 wt pet) at the eutectoid temperature, 1065°C. A previously unreported high-temperature phase which decomposes eutectoidally at 1065 °C was found to exist in the beryllium-nickel system at a composition of approximately 8 at. pct Ni (36 wt pet) by diffision-couple analysis. The presence of this phase was confirmed by thermal analysis and metallo-graphic analysis of the structure resulting from the eutectoid decomposition. G. V. Raynor1 has treated the solid solubilities of some of the elements in beryllium on the basis of the "Hume-Rothery" rules2 which have been modified to include ionic size and ionic distortion effects. It was predicted that the solubility of iron and nickel in beryllium should be slightly less than that of copper. The lowering of the solubility, according to Raynor, is due to a more unfavorable relative valency effect and an ionic size effect. Kaufmann and corzine3 have compiled data on the solubilities of elements in beryllium and have discussed them in the light of the Raynor paper. These authors feel that, because the elements having the greatest solubility in beryllium systematically fall in the Group VIII and IB Columns of the periodic table, the electronic structure greatly influences the maximum solid solubility of elements in beryllium. The solubility of iron in beryllium was determined by Teitel and cohen4 as part of the study of the beryllium-iron phase diagram. The determination was carried out by X-ray and thermal analysis and according to the phase diagram presented, the maximum solubility of iron in beryllium is 0.41 at. pct (2.5 wt pct) at 1225oC. However, it is estimated that the uncertainty in the position of the a-beryllium primary solid-solution boundary is about 0.5 at. pct (3wtpct). Losana and Goria3 in studying the beryllium-nickel phase diagram, determined the solid solubility of nickel in beryllium by thermal analysis. They found the maximum solubility to be between 1.65 and 2.65 at. pct (10 to 15 wt pct) at 1240°C. This value decreased rapidly with decreasing temperature. In determining approximate ranges of solubilities for different elements in beryllium, Kaufmann, et al,8 reported a value of between 1.3 and 1.7 at. pct (7.9 to 10.1 wt pct) for the solubility of nickel in beryllium. The value was obtained by metallographic examination of quenched alloys and lattice-parameter measurements. However, the authors also noted a single-phase structure for a 1.7 at. pct Ni alloy (10 wt pct) on cooling from the liquid. This would indicate a higher solubility range than was reported. ~isch,' in his X-ray studies of beryllium-copper, beryllium-nickel, and beryllium-iron intermetallic compounds, reports the disappearance of a second phase (Ni,Be2) in the beryllium primary solid solution at approximately 4 at. pct (20 wt pct). THEORY The analysis of concentration gradients in diffusion couples has proven to be a useful tool in determining phase equilibria.8-14 In this particular study the diffusion couples were chosen to straddle the expected composition range of the phase boundary, then heat treated at a given temperature and the concentration gradient evaluated. The composition of the phase boundary for a given temperature appears at a point of discontinuity of the composition gradient. Examples of typical phase diagrams and the concentration gradients which should be found in such systems are shown in Fig. 1. In the present work, gradients of the form of Fig. l(c) were obtained in diffusion couples made of pure beryllium and two-phase alloys of beryllium with either iron or nickel. The composition at the point where the gradient becomes discontinuous, Cs, corresponds to the solubility limit of either iron or nickel in beryllium. The analysis of the concentration gradients was carried out by an X-ra absorption method developed and applied by Ogilvie and later used by Moll13 and Hilliard.l4 It depends on the fact that the absorption of X-rays by matter is determined by the concentration and type of the various atomic species present. The relationship for the intensity, I, of a monochro-

Jan 1, 1960

By M. Shelef, A. W. Fletcher

The effect of alkali sulfates in promoting the sul-fation of nickel and copper in a bulk sulfide flota -tion concentrate by fluidized bed roasting has been studied in the laboratory, and it was shown that the various alkali sulfates promote sulfation to approximately the same extent. The sulfation of a mixture of synthetically prepared iron and nickel oxide and of nickel ferrite has also been studied. Nickel sulfation was promoted by high ratios of Fe:Ni and by the presence of sodium sulfate. THE work described in this paper was a continuation of earlier studies into the role of alkali sulfates in promoting the sulfation roasting of nickel sulfides1,2 in an endeavor to determine how the system was affected by the presence of compounds of iron and copper. The earlier work1 showed that, in the sulfation of NiO at 680°C, the reaction was limited by the formation of an impermeable film of nickel sulfate on the oxide surface. The relative effect of the various alkali sulfates in promoting nickel sulfation varied in the order: Li > Na >Cs > Rb > K A study of alkali sulfate/ nickel sulfate interactions at high temperatures showed that the promoting action was due to the fact that the nickel sulfate product layer sintered and agglomerated only when the more active additives were present. This resulted in the formation of discontinuities in the nickel sulfate layer so that diffusion of the sulfating gases to the NiO surface was no longer impeded and the reaction could proceed to completion. A similar explanation was used for the observation that sodium and lithium sulfates promote the oxidation of NiS to NiO at temperatures below 750°C since small amounts of nickel sulfate were formed during oxidation.2 It was of interest to study the effect of alkali sulfates on the sulfate roasting of a sulfide flotation concentrate which is typical of material treated commercially. In order to control temperature it is essential to roast sulfides in a fluidized bed and this technique was therefore used, although the batchwise operation of a small-scale laboratory reactor does not reproduce all conditions which prevail in full-scale continuous plant. The results obtained are therefore only comparative, and cannot be used for predicting the optimum conditions for metal extraction. The sulfation of synthetically prepared mixed oxides of nickel + copper and nickel + iron and of nickel ferrite was also studied to evaluate the relative effects of alkali sulfates with more complex systems. SULFATION ROASTING OF A SULFIDE FLOTATION CONCENTRATE The bulk sulfide flotation concentrate used in this work contained 7.92 pct Ni, 1.74 pct Cu, 35.66 pct Fe, and 31.28 pct S. The sulfide minerals present in order of abundance were pyrrhotite FeS, pyrite FeS2, pentlandite (FeNi)S, and chalcopyrite CuFeS2. Two samples described as coarse and fine were used. The coarse sample, which was a flotation concentrate (58 pct plus 300 mesh), was ground to 100 pct minus 350 mesh to produce the fine sample. Before roasting, the sample of sulfide concentrate was agglomerated by wetting witli a solution of the alkali sulfate (or water), thoroughly mixing, and drying at 110°C. This gave a cake which was gently crushed and screened, the -18 +100 mesh fraction being used for fluidized bed roasting. A similar-size fraction had been used by the authors in pilot plant work with a 4-in.-diam fluidized bed reactor.' In this work it was found that the molar ratio of additive to the total iron + nickel + copper content of the sulfide sample should be adjusted to a value of approximately 0.06, as this was the optimum amount necessary for nickel sulfation. Experimental. The fluidized bed reactor consisted of a quartz tube approximately 60 cm long and 30 mm in diameter resting in a vertical tube furnace. The sulfide bed (30 g) was supported on a bed of -4 +12 mesh quartz particles 3 cm high, which rested on a sintered quartz disc welded to the tube. The temperature of the furnace was controlled with a variable transformer to give a final bed temperature of 680°C. The bed was fluidized with air or mixtures of air + 10 pct v/v SO2, at a total apparent gas velocity of 60 to 65 cm per sec at 680°C. The SO2 was introduced into the fluidizing air stream only when the oxidation of the sulfides was completed. At the end of the roasting period the calcine was leached with boiling water and the

Jan 1, 1964

John Birkinbine, Philadelphia, Pa.: We have in the Institute two Dudleys—Dr. Charles B. Dudley, who has so thoroughly studied the chemical composition and physical behavior of rail-steel, and Dr. P. H. Dudley, whose investigations and

Jan 1, 1900

By A. S. Malicsi, R. J. Lipp, I. Iwasaki

A loch-grade copper-nickel deposit, with an estimated 4.6 Gt (5 billion st) and average analyses of 0.6% copper, 0.2% nickel, occurs in northeastern Minnesota. In addition to copper, nickel, cobalt, and precious metals, the Duluth gabbro contains magnetite, ilmenite, olivine, plagioclase, and biotite. It u estimated that flotation tailings that would be produced by a concentrator of optimal size to sustain a smelter would amount to 20 Mt/a (22 million stpy). The flotation tailings, having already been ground, warrant a closer examination for recovery and use of potential byproducts. Residual sulfide minerals and fibrous minerals may also be isolated and treated separately for useful purposes or for disposal in an environmentally acceptable manner. Two flowsheets were developed; one involving preconcentration by low- and high-intensity magnetic separation and another involving preconcentration by gravity concentration. Concentration methods for recovering and purifying individual byproduct minerals were investigated. From their chemical, physical, and mineralogical characteristics, the potential areas of application and marketabilities of each product fraction were surveyed.

Jan 1, 1985

By J. H Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By J. H. Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By J. S. Fulton

Those who live in steel-mill towns are so accustomed to the sight of flames spouting from the mouth of a Bessemer vessel that they seldom pause to think of the amazing process behind it. Actually cold air is being blown through a hot liquid and, instead of cooling it, raises the temperature of the liquid. When coffee is too hot to drink, we know that blowing on it will cool it, so it was no wonder that when Henry Bessemer (or William Kelly, as your patriotism chooses) first proposed this cycle of steel production, he was considered mad. When Bessemer and Kelly started their investigations around 1852, there was not much practical knowledge of metallurgy and, in consequence, there was wide variation in the product made by their process. It was appreciated that the silicon, carbon and iron were all potential fuels, but not until Mushet discovered the beneficial effects of having manganese in the pig iron did the process really become commercial. Bessemer's patent of 1855 covered a crucibleful of liquid iron into which a refractory tuyere was lowered and the blow started. Since that time virtually every conceivable form of vessel, bottom arrangemerit, tuyere size and location have been suggested or tried. There have been stationary vessels with fixed bottoms, that were side, top or bottom blown; tilting vessels with two sets of side tuyeres at different elevations; vessels like a three-compartmerit septic tank; vessels of a cylindrical form supported on the long axis with tuyeres along the side submerged by a partial rotation of the vessel (this type continues in copper refineries); portable vessels to make the blow in a ladle over a mold in a foundry; a combination of a cupola and converter in one shell, and various other arrangements. But in all these experiments, compressed air for the blast was presupposed and there was little discussion of the quantity or quality of the air delivered to the tuyeres. At one time or another various practices that now are forgotten have been tried or suggested: for instance, the use of inert gas at the end of the blow; the addition of fuel to the blast; the use of hot-blast stoves; the drying of the air to a minimum moisture in the blast. Except in the last-named method little attention was paid to the quality or quantity of the air blown. Phases Of the many Papers published On various phases of the Bessemer process, nearly '7' according to one bibliography, Over go per 'ent were concerned with the metallurgical phase and less than '0 per cent discussed various sections of the pneumatic phase. Since the two phases are coincidental, apparently nine times as much thought has been given to the result as has been given to One of the causes of the Bessemer process. IS it not possible that if more attention had been paid to the pneumatics so many papers would not have had to be written on the troubles in the metallurgical phase? A study of published papers and conversation

Jan 1, 1941

By G. C. Kuczynski

Two particles in mutual contact form a system which is not in thermo-dynamical equilibrium, because its total surface free energy is not a minimum. If such a system is left for a certain period of time, the bonding of the two particles will take place in order to decrease the total surface area, even though the temperature is lower than the melting point. This phenomenon of bonding of two or more particles with the application of heat only and at temperatures below melting point of any component of the system will be called sintering, although the powder metallurgists use this term in a broader sense, including the presence of molten phase and pressure. It is the objective of this paper to study this process and the mechanisms involved in it. This problem is of utmost importance to powder metallurgy and powder ceramics, and its technological aspects have been studied for a good many years. However, the powder metallurgical operations are too complex and include too many superimposing mechanisms, and too many variables for a direct study. It was therefore advisable for the purposes of this study to reduce the variables to a minimum. In this work the radius of the interface formed during bonding in a simple system composed of a spherical particle and a large block of the same metal was studied as a function of time and temperature. It is believed that the mechanism involved in this simple process is fundamental to any sintering operations. Previous Work J. Frenkell was the first to make a serious attempt to develop a theory of sintering. He assumed that the process consists of a slow deformation of crystalline particles under the influence of surface tension which reduces to a viscous flow where the coefficient of viscosity n is related to the self-diffusion coefficient D by the following equation 1 _ D D6kT [1] where 6 is interatomic distance, k the Boltzman constant, and T the absolute temperature. This type of viscous flow of a crystalline substance is essentially different from the ordinary plastic flow. The latter is a specific propcrty of crystals and cannot take place in amorphous bodies. According to Frenkel this viscous type of flow is due to the diffusion of the holes or vacancies arising in the lattice. He was able to derive an equation relating the growth of the interface between two spherical crystalline particles or between a particle and a semi-infinite crystal (Fig 1) to time t at constant temperature. This relationship can be written as follows: x²— 3/2 a/nt [2] where x is the radius of the interface assumed to be circular, a the original radius of the sphere and a surface tension of the material. The other assump- x tions are that x is less than 0.3 and that during the period 1 the original radius, a, of the metallic particle did not change appreciably. A. J. Shaler and J. Wulff2 followed closely the ideas of Frenkel in their theory of sintering of a mass of metallic powder. Neither Frenkel nor Shaler has validated his theoretical speculations with conclusive experimental data. Two measurements reported by

Jan 1, 1950

Earnings of engineers in the period 1956 to 1958 continued the upward trend observed in the previous survey interval, 1953 to 1956. The overall median (all graduates) was $6500 in 1953, $7750 in 1956 (a 19 pct upstep or about 6.5 pct annually), and $8750 in 1958 (up 13 pct from 1956 or 6.5 pct average yearly). The latter represents an increase from mid-1956 to mid-1958. For this same two-year span the Consumer Price Index rose 1.5 pct and the Average Gross Weekly Earnings for Production (Manufacturing) climbed close to 10 pct. Median earnings for the major classifications studied are presented in Table I. The increase in engineering earnings are not distributed equally among the various activity classifications or among the experience levels of the survey. Summary results of the changes of the median lines for the major divisions are presented in Table 11. Data in this table are approximations- dollars are rounded to the nearest $50 unit and percentages to the nearest full percentage.

Jan 1, 1959

By J. H. Wernick, S. Geller

A number of new AB, compounds, in which A is a rare earth or yttrium atom and B is Al, Mn, Fe, Co, or Ni, having the cubic MgCu, structure (Laves phase) are reported. In most of the compounds, the interatomic distances are normal; the lanthanide contraction is observed. However, in the compounds CeB2, B = Fe, Co, Ni, Ce appears to have a valence substantially greater than three; in CeAl2, Ce appears to be trivalent. These results are interpreted as vesulting from an energetically more favorable situation for the 4f electron of Ce to be lost to the 3d band of Fe, Co, nnd Ni. Evidence for the existence of homogeneitj! ranges in these compounds is presented. THE purpose of this paper is to report on the crys-tallographic investigations of a large number of new compounds, Table I, with the MgCuz structure (cubic Laves phase). It is a part of a continuing study of the magnetic properties and structures of binary systems involving the rare earths. In a previous paper' some of the magnetic properties of such systems were reported briefly. We have also reported2 a number of compounds of the CusCa type. The compounds were prepared by induction melting in Argon atmosphere of mixtures of stoichiomet-ric amounts of the constituent elements.* For most of the compounds fused alumina or silica crucibles were used as the containing vessel; graphite crucibles were used to prepare CeA12, NdAl2 and TbA12. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis-type Norelco cameras of 114.6 mm diam. The compounds AB2 belong to space group Fd3m-Ol with 8A in a): (000; 01/2 '/2;3) + 000-; b % XA and 16B in dl: (000; oVa %; 3) + 5/87; % %; 7e % Vs\£>. Because the intensities of the reflections on the powder photographs of the different compounds are similar, relative intensities were computed only for DyMnz for CrKa radiation, Table 11. In the calculation of intensities, the Thomas and umeda3 atomic scattering factors, corrected for dispersion,4 were used. The agreement between observed and calculated intensities leaves little doubt that DyMnz has the MgCuz structure. Crystallographic data for the ABz compounds are given in Table JII. Twelve of these compounds have been reported by other authors. A comparison of the published results with our work is given in Table W.* ers of elements of lower purity, to peritectic reactions in some cases, and to the presence of homogeneity ranges in these alloys, so that melting losses would still result in single phase alloys. The possibility of existence of homogeneity ranges in these compounds was investigated systematically only for GdMnz. At room temperature, the solid solution range is between

Jan 1, 1961

By Earl Hanson

FIRES in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of .$61,996,719.

Jan 1, 1936

By Donald L. Katz

Charts for predicting the pressure to which natural gases may be expanded without hydrate formation have been prepared for gases of even gravity. Pressure-temperature curves for hydrate formation were established for gases having gravities from 0.6 to 1.0. These curves and the thermal behavior of the gases during free and adiabatic expansion were used to prepare the charts for estimating the permissible expansion of natural gases without hydrate formation. The problem was solved by L. F, Albright, W. T. Boyd, J. J. McKetta, G. Martin, P. Poettman. and A. P. Snyder.-, who are first-year graduate students in the department of Chemical and Metallurgical Engineering at the University of Michigan. This paper is essentially a summary of their results. Prediction of Conditions for Hydrate Formation in Natural Gases Each natural gas under a given pressure will form solid hydrates at a corresponding temperature provided sufficient water is present.1-5 The temperature of natural gases below about 5000 lb. per sq. in. decreases when the gases are expanded freely.6,7 This decrease in temperature may cause the expanding gas to enter the region of temperature and pressure at which hydrates will form' The final pressure to which a natural gas may 'be expanded without hydrate formation depends upon the initial temperature and pressure and the gas composition. This paper presents charts that give the final pressures to which gases of gravity 0.6 to 1.0 at given initial temperatures and pressures may be expanded without formation of hydrate. Hydrate-forming Temperatures and Pressures as a Function OF Gas -Gravity Experimental data of pressure versus temperature at which solid hydrate will form, provided sufficient water is present, are available for a series of gases.2,3 A method of predicting the pressure-temperature curve for a given gas composition has been reported.' The solution to this problem requires that these curves relating pressure to temperature be established for gases of given gravities.

Jan 1, 1945

By N. M. Levine, W. M. Fassell

In this laboratory study the problem of aerative conditioning to separate chalcopyrite and pyrite from cobaltite was simply effected with a sulfy-drate collector and pH by proper choice of mixing variables. It was shown that for a given impeller type and geometry, selectivity is governed by a relation between the Froude number and a modified power number multiplied by impeller tank-diameter ratio wherein the power factor is expressed as power intensity or horsepower per unit volume of contained pulp. In applying this approach to other systems, other criteria would be used in place of selectivity. The purpose of this paper is to show how solutions to problems of aerative conditioning of pulps may be enhanced by development of mixing parameters in a given system through application of a fundamental approach to agitation. The term aerative conditioning refers to a combination of processes which include mechanical gas dispersion, gas solution in the liquid phase, transport of dissolved gases and other reactants to the reaction zone, physico-chemico interaction within the liquid phase and/or at the solid surface, and, finally transport of products away from the reaction zone. Important elements of these processes are: 1) Air-Liquid Contact Area: This area limits the rate at which a given gas may dissolve in a given liquid. Thus, an aerative conditioning system should be designed for optimum gas dispersion. 2) Diffusional Factors: Such factors as concentration gradient, diffusion film thickness, and diffusivity may govern the rate at which dissolved constituents are transferred to the zone of interaction at a particle surface and the rate at which reaction products are transported therefrom. Thus, such systems would be designed for maximum turbulence to effect good mixing and to minimize diffusion film thickness. 3) Solids-Turbulent Liquid Contact Time: Sufficient time should be provided for interactions to take place at solid-liquid interfaces. The region of maximum turbulence for mechanical systems being in the impeller zone, it is important that the number of passes through this zone be optimized. This means that a proper balance should be struck be- tween flow and turbulent power to achieve optimum conditioning time. Too high a flow rate and insufficient turbulence may be improper if the reactions are diffusion limited. On the other hand, too much turbulent power and too little time in the reaction zone due to insufficient flow power may also be limiting. 4) Geometry and Impeller Design: The design of the conditioning vessel and the type of impeller employed are important factors in determining the relative distribution between flow and turbulent power and the degree of gas dispersion. Maximization of power input would be to no avail if the distribution between flow and turbulent power were improper or gas dispersion insufficient. 5. Physical Chemistry: The reactions between dissolved gases and solid surfaces may be limiting if gas solubility, activation energies and/or free energies are not favorable. J. H. Rushton, E. W. Costich, and H. J. Everett' have summarized the mechanical elements of the combination of processes listed in a fundamental mixing equation. This equation was derived by dimensional analysis and relates the physical variables for a single impeller, centered in a cylindrical, vertical axis, flat-bottomed tank. It is, where T is tank diameter in feet; H is liquid depth in feet; C is height of impeller off tank bottom in feet; S is pitch of impeller; L is length of impeller blades; W is width of impeller blades; R is number of baffles; D is impeller diameter in feet; Np is the power number, pg/dN3D5; P is power in foot-pounds per second; g is the gravitational constant, feet per second; J is width of baffles; B is number of im-

Jan 1, 1961

By Charles H. Fulton

FOR some time it has been thought that there should be > closer relationship between the members' of the Institute engaged in education in the mining schools, the mining, metallurgical, ceramic, and geological departments of universities, and the members of the Institute actually engaged in the production of mineral products and the operation and direction of works. The American Society of Chemical Engineers and the American Ceramic Society have for some years past devoted especial attention to the educational matters of their respective fields. The Engineering Foundation, representing the great engineering societies of the country, is deeply interested in technical education and maintains a Committee on Educational Research.

Jan 1, 1932

By H. F. Perkins

CORROSION as an economic problem is growing rapidly in importance not only because it entails a replacement of corroded parts, but because it interrupts operation and causes hazards of damage and injury through failures of corroded equipment. Nearly all industries are interested in this subject. This paper, although concerned chiefly with corrosion in a complete refinery on the sea coast, discusses many of the various forms of chemical decomposition, most of which are found universally. The petroleum refining industry, in the writer's opinion, is seriously afflicted by the presence of sulfur in nearly all crude oils. The complete removal of sulfur from the crude as it enters the plant would cause such a relief from corrosion that this problem for research would seem to demand active attention. Next to sulfur the most troublesome corrosive agent is the saltmagnesium chloride, found in the water associated with crude oil, the last traces of which are so difficult to remove. This is much less serious, however, than the sulfur. Refinery corrosion can be tabulated as follows: Causes of Corrosion and Places of Attack in a Refinery CORROSIVE ELEMENTS MATERIAL ATTACKED Air: Pipe lines Moisture Tanks COQ Electric fixtures Sulfur gases Still towers Chlorine Condenser boxes Other acid-forming gases Ladders and stairs Smoke stacks Steel buildings All exposed metal Water: Alkali Fire lines and hydrants Acids Cooling water lines Air Condensers and coolers Other dissolved gases Boiler tubes Steam Steam pipes and valves Turbines Oil Sulfur compounds Tanks, pipes, valves, stills, towers MgCl2-Hydrochloric acid Condensers Air contamination

Jan 12, 1926

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper discusses the results of the Fry conventional or cocurrent in situ combustion test, which was conduct-ed in a 3.3-acre inverted five-spot. The depth of the formation was between 880 and 936 ft; the oil had a specific gravity of 28.6° APl and a viscosity of about 40 cp at the reservoir temperature of 65°F. Preceding the combustion test, air injection tests were conducted which, in conjunction with geological studies, were used to evaluate the characteristics of the reservoir. Combustion was initiated on Oct. 13, 1961, with ignition being accomplished by a 40 kw electrical heater. The test phase of the project ended on Oct. 1, 1963. During the test, the average air injection rate was 1,520.-000 scf/D. Throughout the test, production of all fluids— gas, oil, and water—was monitored. Cumulative oil production credited to the project was 100,586 bbl. The cumulative air-oil ratio was 11,500 scf/bbl oil, and the oxygen uti1ization efficiency was 87 per cent. INTRODUCTION The Marathon Oil Co. conducted a successful in situ combustion test, beginning Aug. 22, 1961, at the Fry unit, Crawford County, 111. The purpose of the project was to test the feasibility of cocurrent in situ combustion as a means of oil recovery in the Fry type reservoir. Interest in in situ combulstion as an oil recovery tool has been stimulated mostly by the existence of large reserves of heavy viscous crudes with low expected recovery, usually less than 10 per cent. These are the so-called unrecoverable reserves, and most combustion tests to date have been conducted in this type of reservoir.1-4 In contrast, the Fry combustion test was conducted in a reservoir with a relatively high gravity oil having a relatively low viscosity. This paper discusses the performance of the test. The geology of the reservoir and the field operations are discussed in separate papers.5 TEST SITE The Fry combustion test was carried out in a 3.3-acre inverted five-spot portion of a lenticular body of Robinson sandstone. Net sand was 50 ft thick, porosity averaged 19.7 per cent, oil saturation was 68 per cent of pore volume, and water saturation was 20 per cent of pore volume. The oil in place was estimated at 1,040 bbl/acre-foot, or 171,600 bbl within the 3.3-acre pattern. The water in place was 326 bbl/acre-foot, or 53,800 bbl. The oil has a specific gravity of 28.7° API and a viscosity of 40 cp at the reservoir temperature of 65°F. AIR INJECTION PERFORMANCE Air injection took place in two phases, the phases separated by ignition of the reservoir. In the pre-ignition phase, air injection tests were conducted in the summers of 1960 and 1961. These indicated that the Fry reservoir was confined, and a high return rate of injected air could be expected. This proved to be an outstanding characteristic of the project, as cumulative gas production was 95.3 per cent of the air injected. The difference between the cumulative air injected and the total gas produced can be largely accounted for by the quantity of air stored in the reservoir. An estimated 16 X 10 cf of air remained in the burned-out portion of the reservoir and an indeterminate amount of gas was stored in the unburned but pressurized reservoir. Hence, a complete material balance of gases would account for nearly 100 per cent of the air injected. At times during the test, the daily gas production rate was 98 per cent of the daily air injection rate. Fig. 1 presents the air injection history of the Fry com-

Jan 1, 1966

H. N. EAVENSON, Gary, W. Va.-Judging from our own experience, the statement that only 40 per cent. of the accidents are caused by the human element is very low. We have adopted all the measures that Mr. Wilson recommended, such as systematic timbering, use of permissible expolsives and practically everything that anybody has suggested or can think of, and even after all that has been done, done for several years, and a systematic campaign maintained all the time to reduce accidents, we still

Jan 4, 1918

By D. I. Bardos, Paul A. Beck

A MARK, Boren, and westgrenl in their X-ray diffraction study of manganese alloys with 10 to 25 at. pct Si reported the occurrence of a phase with complex crystal structure in a Mn + 14.5 at. pct Si alloy after annealing at 800° or at 600°C. Recently Kuzma and Gladyshevskii2 identified Mn6Si as an R phase,3,4 the second binary R phase known. (A binary R phase was previously found in the Mn-Ti system by Waterstrat.5) A ternary R phase was reported earlier0 near the Mn-Si binary border of the Ti-Mn-Si system at 1000°C. In the light of the Russian work it now appears that this "ternary" R phase may be in fact an extension of the binary (Mn6Si)R phase. As already found by Amark, Boren, and Westgren, the corresponding binary phase is absent at 1000°C; the effect of titanium is evidently to stabilize it up to higher temperatures. In a recent paper Wieser and Forgeng7 gave the boundaries of this binary phase, which they referred to as 6. In order to re-examine the identity of this phase, an alloy of Mn + 14.5 at. pct Si was prepared by induction melting in helium atmosphere and annealed for 3 days at 800°C. The powder pattern, taken with an asymmetrical focusing camera of large dispersion and shown in Table I, was found to be that of the R phase, in agreement with the results of Kuzma and Gladyshevskii. For comparison, Table I also lists

Jan 1, 1965