Search Documents

By R. S. Dean

PROCESSES for the direct production of iron and steel from ores are hardy perennials, and new processes and revivals of old ones are continually being brought to the attention of the investing public if not to the attention of metallurgists. Direct production of iron and steel is so simple that it offers a fertile field for the promoter. Unfortunately in this way direct processes have acquired a bad name, not always deserved, with conservative capitalists and metallurgists. Direct processes cannot, except in special instances, be looked upon as a substitute for any single operation in present iron and steel practice but must be considered, as one link in an entirely new chain of metallurgical process from ore to finished steel. Thus it is, in my opinion, inadvisable to consider the use of sponge-iron processes as a means of treating ore of ordinary blast-furnace grade to produce open-hearth feed. In time I think it will be found equally inadvisable to smelt iron-ore concentrates in the blast furnace.

Jan 1, 1935

By S. K. Basu, H. H. Kellogg

THE physical-chemical behavior of the system Pb-S-0 is of prime importance to the understanding of lead smelting processes, yet little accurate information is available on either equilibrium or kinetic behavior in this system. This paper is the first report of a program designed to fill gaps in our knowledge of this system. In the total ternary Pb-S-0, the region of greatest metallurgical interest is that bounded by the compositions Pb-PbS-PbS0,-PbO-Pb. Systems richer in sulfur, or richer in oxygen,* than those essentially pure SO2. This conclusion follows from the fact that all systems are in a highly reduced state, since either PbS or Pb is a constituent of all the equilibria. The content of 02, SO3, S2, S6, S8, and so forth, can be shown to be negligible compared to SO, in all such systems.* corresponding to this region can only be obtained at gas pressures exceeding 1 atm, a condition seldom met in lead smelting practice. Not only is the present study limited to condensed phases within this portion of the total system, but it is limited to temperatures at which all phases are pure solids, except for lead, which is liquid. In this limited system the following seven condensed phases are known to exist: Pb(l), PbS(c), PbO(c), PbSO,(c), PbSO,•PbO(c), PbSO4 • 2PbO(c), and PbSO, -4PbO(c). PbO exists in two crystal modifications,' but only the high-temperature yellow form is considered here. Schenck and co-workers2-4 reported the compound PbSO4 3Pb0 to be stable at high temperature, but the more recent work of Lander,5 and the present work, prove that the tetra-basic sulfate, rather than the tri-basic sulfate is stable. Fig. 1 shows the composition diagram for the binary PbO-PbSO2, based primarily on the work of Lander. In this study the univariant boundaries and invariant points existing among these seven condensed phases and the gas phase have been determined. In a ternary system, the phase rule indicates that an invariant point involves the simultaneous equilibrium of five phases—four condensed phases and the gas phase. A univariant relation involves four phases—three condensed phases and the gas phase. The gas phase in the systems studied is The following stable univariant equilibria between SOz and the condensed phases were identified: (a) PbS + 7PbS04 = 4(PbSO, - PbO) + 4SO2 (b) PbS + l0(PbS04 • PbO) = 7(PbSO4- 2PbO) + 4SO2 (c) PbS + 8(PbSO4 • 2PbO) = 5(PbSO4 . 4PbO) + 4SO2 (d) Pb + PbSO, • 4PbO = 6PbO + SO2 (e) 3PbS + PbSO4 . 4PbO = 8Pb + 4SO2 (f) 3PbS + 16(PbS04 PbO) = 7(PbSO4 . 4PbO)+ 12SO2 (g) 2PbS + PbSO,2PbO = 5Pb + 3SO2 (h) Pb + 3(PbSO4 . 2PbO) = 2(PbSO,. 4PbO) + SO, Of these eight univariant equilibria, five were measured in this work (a, b, c, d, and g) and the behavior of the other three (e, f, and h) was calculated by thermodynamic analysis of the measured data. Two invariant points were found corresponding to simultaneous equilibria as follows: Point 1: PbS, PbSO4PbO, PbSO4.2PbO, PbSO, - 4PbO, and SO2 Point 2: Pb, PbS, PbSO, . 2PbO, PbSO, - 4PbO, and SO2, From the measurements it was also possible to calculate the thermodynamic properties of the three basic sulfates of lead at 298.16°K. EXPERIMENTAL Apparatus—The experimental method consisted of the measurement of the gas pressure exerted by a given reaction mixture at a given temperature. An iridium crucible was used to contain the reaction mixture. There was no evidence of attack of the iridium,* but after use at high temperature for a week

Jan 1, 1961

By C. E. Reinhard

A useful accelerated weathering test should be capable of placing any series of metals quantitatively in the same order of endurance as that noted under a particular set of actual exposure conditions. The development of such a test must necessarily depend to a considerable extent upon data obtained from a wide variety of exposures. This paper offers preliminary data from exposure tests on nine metals placed in 11 locations in the Lehigh Valley, within a radius of 20 miles from Palmerton. The exposure conditions vary from a severe industrial atmosphere to a pure rural atmosphere. The data are offered as evidence of the necessity for the identification and evaluation of the variables of corrosion and as illustration of some of the variations to be considered in the development of a useful accelerated test. It is quite clear, from this evidence, that a useful accelerated test must be versatile to the extent of showing the probable variations of corrosion resulting from differences in atmosphere as well as from differences in the metals. The paper is presented solely with the object of pointing out the wide variations in relative merits of several common metals in resisting corrosion and without any thought of initiating controversy regarding the merits of particular metals. For this reason the metals are designated only by symbols in the tables and no key is given to these symbols. Test Procedure Specimens, 4 by 6 in., were cut to accurate dimensions from each of the following metals or alloys: aluminum, ascoloy, copper, copper steel, galvanized iron, and zinc. Additional grades of these metals bring the total to nine types. Since it was impossible to obtain the required number of copper-steel specimens having equal surface conditions of rust and scale, it was thought advisable to pickle these specimens in a hot solution of 10 per cent. sulfuric acid. All other specimens were carefully cleaned in ether and alcohol and weighed just prior to exposure. Four specimens of each type of metal were mounted on a test rack by means of porcelain insulators. The racks were so constructed that

Jan 1, 1929

By C. E. Reinhard

A useful accelerated weathering test should be capable of placing any series of metals quantitatively in the same order of endurance as that noted under a particular set of actual exposure conditions. The development of such a test must necessarily depend to a considerable extent upon data obtained from a wide variety of exposures. This paper offers preliminary data from exposure tests on nine metals placed in 11 locations in the Lehigh Valley, within a radius of 20 miles from Palmerton. The exposure conditions vary from a severe industrial atmosphere to a pure rural atmosphere. The data are offered as evidence of the necessity for the identification and evaluation of the variables of corrosion and as illustration of some of the variations to be considered in the development of a useful accelerated test. It is quite clear, from this evidence, that a useful accelerated test must be versatile to the extent of showing the probable variations of corrosion resulting from differences in atmosphere as well as from differences in the metals. The paper is presented solely with the object of pointing out the wide variations in relative merits of several common metals in resisting corrosion and without any thought of initiating controversy regarding the merits of particular metals. For this reason the metals are designated only by symbols in the tables and no key is given to these symbols. Test Procedure Specimens, 4 by 6 in., were cut to accurate dimensions from each of the following metals or alloys: aluminum, ascoloy, copper, copper steel, galvanized iron, and zinc. Additional grades of these metals bring the total to nine types. Since it was impossible to obtain the required number of copper-steel specimens having equal surface conditions of rust and scale, it was thought advisable to pickle these specimens in a hot solution of 10 per cent. sulfuric acid. All other specimens were carefully cleaned in ether and alcohol and weighed just prior to exposure. Four specimens of each type of metal were mounted on a test rack by means of porcelain insulators. The racks were so constructed that

Jan 1, 1929

By Charles F. King

THE only investigations on record of the reactions occurring during the Bessemer blow are of charges containing a large percentage of manganese, with the exception of two partial analyses by Snelus and Barker of the. English method, where a low percentage of manganese was used. They do not give the analysis of the spiegel, nor do they report any graphitic carbon after the first stage of the process. Both report only traces of manganese after the first stage until the addition of spiegel. The slags corresponding to the samples of metal were not analyzed.

Jan 1, 1881

By Lester C. Uren

It is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 1, 1925

By W. A. Forbes

PAGE Introductory............357 ReasoNs for Gas Cleaning.........358 First Methods of Separation of Dust.......359 Amount of Dust Produced by the Blast Furnaces of the United States Steel Corporation During 1912.....359 Dust Content in Blast-Furnace Gas.......360 Primary Cleaning. Dry Cleaning: General Remarks..........360 Braasert- Witting Whirler........362 Brassert Modifications of Brassert-Witting Whirler....363 Dyblie Whirler..........363 Remarks on Efficiency of Dry Cleaning......366 Wet Cleaning: Zschocke System..........367 Duquesne Tower..........367 Bian Gas Washer..........369 Final Cleaning. Wet Cleaning: Theisen Gas Washer.........371 Theisen Disintegrator Gas Washer.......372 Schwerz-Bayer Disintegrator Gas Washer..... 374 Fowler & Medley Vertical Gas Washer......376 Feld Gas Washer..........377 Reco Centrifugal Gas Washer........379 Sepulchre Gas Washer.........381 Dry Cleaning: Halberger-Beth Gas-Cleaning System......382 Smith.Bagley Gas-Cleaning System,......384 Howard Dust Separator.........387 Possible Separation of Dust by Electrical Precipitation ... 389 KapnOGraph............389 Methods of Determining DUst in Gas.......389 Advantages of Clean Gas.........393 Introductory. During the early stages of blast-furnace practice. the gas formed in the furnaces by the combustion of the coke used in smelting the ores was allowed to escape into the atmosphere. The light furnished

Jan 1, 1914

ALABAMA. Aldrich.-Aldrich, W. F. Anniston.-Noble, A. E., 20th St. and Wilmer Ave. Auburn.-Brown, R. L., Box 0. Bessemer.-Abbott, C. E., T. C., I. & R.R. Co. Ferguson, V., U. S. C. I. Pipe & Fdy. Co. Williams, E. P., Tenn. C., I. & R. R. Co. Birmingham.-Aldricb, T. H. Aldrich, T. H., Jr., 406 Woodward Bldg. Allen, A. W., 1616 S. 14th Ave. Bowron, J., 1401 S, 20th St. Burbidge, T. A., Browu-Marx Bldg. Coxe, E. H., Tenn. C., I. & R. R. Co. Crawford, G. G., Tenn. C., 1. & R. R. Co. Crockard, F. H., Woodward Bldg. Dimmick, F. D., Dimmick Pipe Co. Ellis, E. E., 1515 Brown-Marx Bldg. Fairbairn, C. T., Woodward Bldg. Fies, M. H., 2316 Highland Ave. Hiller, E., 516 Brown-Marx Bldg. Hillman, M. P. G., 707 Empire Bldg. Ludwig, C. P., 12th Ave. and 12th St. McCormack, G. B., Lookout Mt. Iron Co. McCrery, C., Tenn. C., I. & R. R. Co. Moffett, C. A , 909 Brown-Marx Bldg. Peters, R.. Jr., Brown-Marx Bldg.

Jan 1, 1917

By Ralph H. Sweetser

IN the recent world-wide deflation of commodity prices the coal industry, including both anthracite and bituminous coal, had reached a level where the actual delivered market prices received by the operators were usually less than the cost of production. Many steel companies and public utilities, operating their own "captive" mines, could have bought coal during the past three years for less money than the true cost of coal produced at their own properties. Competition within the coal industry itself was cruel to the point of profitless operation, and the competition of other forms of fuel was bearing heavily on the coal producers. They were thus forced into methods of production and utilization that they had hitherto ignored; there had been almost complete absence of any appreciation (by the bituminous operators especially) of the necessity of real research work in finding better methods of preparing coal for specific uses, and in finding new and profitable uses for different kinds and grades of coal.

Jan 1, 1933

By J. D. Raulerson, J. M. Williams

This paper presents a comparative evaluation of several system currently being used or proposed for the transport of matrix from an open-pit mine to a large fixed plant. The matrix is a sticky, wet clay to be carried from 8-16 km (3-10 miles) at 910 t/h to 1.8 kt /h (1,008-2,000 stph). The system is complicated by frequent moves of the open-pit mine site and other factors, such as use of the clay component in land reclamation.

Jan 1, 1984

By T. M. Girdler

IN THESE perilous days of world- wide uncertainty, this Institute and the profession represented by it take on new importance in the economic life of the nation. I have long been impressed by the fact that the objects of the A.I.M.E. are purely professional and scientific. The country has benefited from your honorable tradition of adherence to those objectives over a period of 68 years. The Institute's policy of refraining from controversial matters - has made possible the serious, balanced, and uncolored consideration of the particular problems that come before it.

Jan 1, 1939

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By H. Rees

This paper supplements and brings up to date a report prepared earlier this year and presented at the Eleventh Pan American Railway Congress in Mexico City. Most of the original report is contained in this paper in order to acquaint the reader with the project background. On December 1, 1961, construction of this locomotive was completed. Stationary testing started immediately, and a host of problems in various areas were uncovered. Many of these had no relation to the use of coal in a direct fired gas turbine. All of them emphasized the problems which plagued previous projects of this kind. In 1944 the Locomotive Development Committee of Bituminous Coal Research, Inc., was formed to study the problems of combustion, coal handling, and fly ash removal which would have to be solved before coal could be used to fire a gas turbine. By 1947 this committee was composed of the chief executive officers of nine eastern railroads and five eastern coal companies. All of the members of this committee were vitally concerned in a coal fired gas turbine because coal cost only one-fourth as much per heat unit as fuel oil. A number of research projects were started to develop and test components on a small scale. This included work at John Hopkins University, Battelle Memorial Institute, Institute of Gas Technology at Chicago, Purdue University, and Southern Research Institute. By 1946 a pilot plant had been installed at the Dunkirk, New York plant of Alco Products Div. of American Locomotive Co. The U. S. Bureau of Mines made available to the Locomotive Development Committee (hereafter called LDC) a Houdry process gas turbine plant, originally destined for a Russian oil refinery. The full scale pilot plant was used to evaluate the results obtained from the small scale studies under actual gas turbine conditions. Operation of this plant disclosed a number of problems which had not been discovered in the small scale tests. By 1951 four 250 hr tests had been conducted with the Houdry gas turbine to test out a variety of equipment. The major problem concerned the removal of abrasive fly ash from the products of combustion so that wear on turbine blades would not be excessive. The first 250 hr test showed that the original fly ash separating equipment was inadequate. Large ash particles passing through the turbine blading were nicking the leading edges of the first row blades. At the conclusion of the second 250 hr test, erosion was so severe that the first row of stator and the first row of rotor blades were replaced. At the end of the third 250 hr test, it was necessary to replace the first three rows of stator blading. The fourth test was used to test out a new design fly ash separator developed by LDC and named the Dunlab tube. This device gave more encouraging results than any of the others tested. Early enthusiasm for overcoming major difficulties had resulted in placing an order in 1946 with Allis-Chalmers Mfg. Co. for a 3750 hp regenerative gas turbine. The gas turbine, together with associated combustion and ash removal equipment, coal handling equipment, generators and gear reduction unit was installed at Dunkirk by 1951. A 750 hr test was made in 1952 with the LDC-Allis Chalmers gas turbine power plant. At the end of this test it was necessary to replace the first four rows of both rotor and stator blading. Rows 5 and 6 did not require replacement. In 1953 the American Locomotive Co. joined with LDC and assumed an active role in equipment development and manufacture. During 1954 LDC-Alco operated the rebladed gas turbine 300 hr to determine if a new fly ash separator was adequate. Performance of the improved separator was considerably better, but trouble was experienced with clogged blowdown lines from the Dunlab tubes. When these lines clogged it permitted the passage of abrasive particles. In 1955 a total of 1421 hr was run. This included 243 hr of cycle operation on Union Pacific coal from the D. O. Clark mine at Superior, Wyoming. During the 243 hr a total of 370 tons of coal was consumed. The purpose of this test was to determine if U.P. coal was suitable for use in a coal fired turbine. It was the unofficial opinion that it was as good or better than the eastern coals that had been tested.

Jan 1, 1964

By Roderick K. Davey

Introduction in any business, it is essential that we select those alternatives which are not only technically feasible, but will be the most profitable to the business m terms of corporate objectives Some of the studies and activities requiring support of financial analysis to select the alternatives which most closely satisfy the management objectives and technical considerations are as follows 1 ) Cutoff grade determination. 2) Ore reserve estimation. 3) Production forecasts (long- and short-term) for an operating mine, development of a new mine, or expansion of an existing mine. 4) Evaluation of haulage alternatives. 5) Evaluation of equipment.

Jan 1, 1979

The thirty-second annual meeting of the Montana Society of Engineers was held at Great Falls, Mont., on Apr. 10-12. The first day was given to the reception of visitors and the second day to the inspection of points of engineering interest. On Saturday, at the business meeting, the following officers were elected: President, Samuel Barker, Jr.; first vice-president, Charles A. Lemmon; second vice-president, George T. McGee; secretary and librarian, Clinton H. Moore; treasurer, Harry H. Cochrane; trustee for three years, Theodore Simons.

Jan 6, 1919

By A. G. Lyle, J. D. Runkle, G. A. Gillies

THE evaluation of data obtained by selective flotation from even a simple ore is a very difficult process, and when the ore tested is complex the process becomes extremely difficult and cumbersome. The authors, in the course of an investigation into the selective behavior of various flotation reagents on nonmetallic minerals§ were confronted with an aggravated form of this difficulty, owing to the large mass of data that had accumulated over a period of years. They finally devised a method whereby the results of the various flotation tests could be correlated and interpreted by means of graphs representing recoveries and rejections of the component minerals in the ore. This method of graphical analysis proved so useful in nonmetallic flotation that it was afterwards applied to sulphide flotation, where it yielded equally satisfactory results. Since this method of analysis leads to very definite conclusions as to the effect of changes in reagents and flotation procedure, it is felt that a wider application of the method might assist the industry by reducing the amount of test work required, and possibly increase the accuracy of the final analysis. GRAPHS In Fig. I, four curves are plotted on the same graph with cumulative percentages as ordinates and cumulative weights as abscissas. In this instance the four curves are named, respectively: the barite-recovery curve, the limestone-rejection curve, the silica-rejection curve, and the summation curve. In these tests barite was the mineral concentrated, therefore a barite concentrate was produced. Definitions Before explaining the curves in detail it might be advisable to define several new terms, such as "percentage rejection," "summation index," and "summation curve," as well as the word "test," which has been used in a special sense. A "test" will include all the operations performed upon a batch of ore from the time it is placed in the rod mill until the last product has been assayed. Thus a test may be a comparatively simple procedure producing only one concentrate and a tailing, or it may be a very complicated procedure producing five or more concentrates of a specific mineral as well as a tailing. The number of concentrates produced will depend entirely upon whether the collector was added to the pulp in the flotation cell in one lot or was added in five or more portions. Percentage Rejection.-The ability of a selective flotation collector to reject an undesired mineral is just as important as its ability to collect the desired mineral. The percentage rejection curves shown on the graphs give this factor due consideration and its value is calculated as follows: Suppose a concentrate contains 5 per cent of an undesired mineral. This indicates

Jan 1, 1942

By Lars Thomassen, Ernest Kirkendall, Clair Upthegrove

THE amount of research done in the last few years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Desch1 in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for its review and bibliography is an article by A. I. Krynitsky.3 While considerable material has appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined at three temperatures. PROCEDURE The method used consisted of plating copper on a beta brass, heating it to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the temperature at which diffusion takes place the beta brass is saturated with copper. Thus, while the beta brass supplies the zinc, no diffusion takes

Jan 1, 1938

By N. E. Holden, R. R. Goodrich

TheRe is a small area about Murray where bedded gold quartz veins occur in Prichard slate. The ore taken from the upper levels, during the early days, was free milling and was treated by stamp milling and amalgamation. There was likewise a considerable placer working. The report is current that tungsten (scheelite) was encountered, which interfered with the amalgamation in the stamp mills and which, in placering, collected in the riffles in the sluice boxes and clogged them. Consequently, in the quartz mines, the scheelite, when encountered, was rejected, being thrown into the waste, sometimes inside the mine and at other times outside on the dump. The free surface ores became worked out and as the ore in depth became pyritic and rebellious to amalgamation the mines closed down. Last spring tungsten ore brought a high price, near $80 per unit, 60 per cent. W03 and up. This so stimulated the output of tungsten ore that old dumps were explored and waste stored in the mines was gone over. Tungsten was likewise mined from virgin ground. So the district produced quite heavily for a time. The condition now is different. The price is not so high, about $20 per unit WO3, which makes profits questionable when mining in new ground. The accumulations from early day mining have been exhausted and the output has greatly declined. The Golden Chest mine was the heaviest producer of tungsten. The months of June and July were spent at this mine studying the problem. Since the mine had produced both gold and tungsten, we looked forward to the problem of recovering both from what might be called a gold-tungsten ore. A study of the Golden Chest vein showed this was not to be the case. While gold ore and tungsten ore come from the same vein, the tungsten ore is confined to a more or less disturbed or distorted portion

Jan 1, 1918

By Frank Rieber

The discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.' The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment is typified by magnetic balances capable of measuring the components of the earth's field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as is possible with the more pronounced anomalies.

Jan 1, 1929