Search Documents

By R. D. Lord

The search for the best practical means of storing sulfide bearing tailings, where there is no residual excess of carbonate material is discussed in this paper• Usually the sulfide content decomposes, with the aid of bacterial action, and the resulting sulfuric acid escapes, along with any heavy-metal solutes, through embankments that are usually porous to some degree• The problem is typified in the tailings of the uranium operations of Elliot Lake, Ont., where mining started some 20 years ago• The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base-metal ores• Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice• Now experience has shown that these areas, some of which have been idle for over a dozen years, release acids in seepage and overflows to an unacceptable degree• To protect natural water courses, neutralizing plants are operated wherever required• Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8•5 and precipitate heavy metals that may be in solution• The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found• The problem differs only slightly from that common to base-metal concentrators in that here the ore has been leached with sulfuric acid for the recovery of uranium• Any native content of calcareous material has been digested, and only that added for final neutralization is available to maintain a pH unfavorable to bacterial activity• Chemical oxidation slowly lowers the pH and when this reaches a level of 4•5 or less, bacteria become active and greatly accelerate the formation of acid. The bacterial process is probably at least ten times as fast as the chemical oxidation• Location and Processing The operations referred to, uranium and one copper mine, are located at approximately 46°N and 82°W longitude• This is typical Canadian Shield country, a land of lakes, deeply glaciated and rocky, with sparse soil which supports mixed forest cover• Drainage is to Lake Huron, 25 miles to the south• Average temperature is 45°F, ranging from -40° to +95°F• Annual precipitation is 38 in•, about half of which is snow• The ore is Precambrian, quartz-pebble conglomerate, with mineralization in the matrix• From 5 to 10% pyrite is present• All known means of pre-concentration have been tested, but a bulk sulfuric acid leach has proved the most efficient. Tailings have from the outset been neutralized before release• Current practice is to add ground limestone to bring the pH to 4•5, and then lime to raise the value to 10•5• Environmental regulations have recently been increased and the foregoing meets the new standards• Separate measures are taken to precipitate radium• Remedial Measures Since the outstanding environmental problem is the oxidation of pyrite by bacterial action, the solution is to contain the products, or arrest the process• Given the ambient temperature, favorable half of the time, four items are essential to the activity• 1) Pyrite• 2) Moisture pH < 4•5. 3) Oxygen• 4) Bacteria• Removing any one of these out of the range of tolerance will bring the reactions under control• A variety of proposals considered, and a number tested for the arrest of the process, are: (a) render embankments impermeable, (b) provide an impermeable cover, (c) cover with an oxygen absorbing layer, (d) provide a vegetative cover, (e) flood the site, (f) remove pyrite from current tailings, (g) add excess limestone to current tailings, (h) poison the bacteria• Bank Seal-On existing impoundment areas, where the embankments are several thousand yards in length, it is believed that any program of injecting sealants can have small chance of success• However, a moisture barrier is an indicated specification for future construction, and this can be highly expensive• Surface Seal-Depending on the configuration of the deposit, the downward travel of water should be prevented, and oxygen excluded• Burying a plastic membrane just below the surface has been considered, as has the application of a liquid sealant that would penetrate the surface. The objection to these remedies is the excessive cost of dealing with large areas and the expectation of only temporary benefit as a result• Frost penetration is over 4 ft, and frost action breaks up asphalt paving and all but heavy concrete in a few years• Organic Layer-An oxygen-absorbing layer, such as bark fines from paper mills has been proposed as a surface treatment• Cultivated into the tailings such material might be expected to arrest subsurface oxidation for some years• Estimates are 100 tons per acre of bark fines, or 35 tons per acre of sawdust, and these enormous quantities do not so far give assurance of providing a long-term remedy• Vegatative Cover-Several obvious benefits would result from a good growth of grass or other vegetation on abandoned tailings• While restoring the natural green of the tract the growth would prevent wind-blown dust and reduce erosion• Subsurface oxidation should be reduced, as well as the upward movement of ground moisture as occurs in dry weather. To this end, considerable research and field testing has been carried out to arrive at a formula - a prescription which will provide a self-sustaining growth on the tailings surface, or at least one that would survive with reasonable maintenance attention. Many test plots have been run with different combinations of surface treatment and seed mixtures. Generally, by addition and close cultivation of limestone, lime, and fertilizers, technical success has been demonstrated• Plants with a high tolerance for acid soil seem the more hardy, and a pH above 3 is indicated so that nutrients can be absorbed• Recommendations are for 12 to 15 tons of

Jan 1, 1977

By George D. Dub

INTRODUCTION OWENS LAKE is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.2H20) and borax, (Na2B407.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. CLOSED BASINS Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I Chloride type; largely sodium chloride (NaCI) and of oceanic type, such as Great Salt Lake. Related is the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. 2. Sulphate type; largely sodium sulphate (Na2S04) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate-chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate-Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1947

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By A. O. Drysdale

In Canada, the market for cement is not a national one but rather a collection of local or regional markets. Excess capacity on a national basis does not necessarily preclude a shortage on a regional basis. with portland cement selling for less than a cent a pound, the low price-to-weight factor makes transportation to the market a major cost item and thus a small plant can be justified to serve a limited regional market. The Brookfield plant of the Canada Cement Co. is designed to supply the Province of Nova Scotia, a regional market that shows promise of growing to a point where it will support a one-kiln plant. The market is presently being served by boat shipments from the Canada Cement Co. plant at Montreal East, Quebec, and from the North Star Cement Ltd. plant at Corner Brook, Newfoundland, and by rail and road shipments from the Canada Cement Co. plant at Havelock, N. B.

Jan 4, 1965

By R. T. DeHoff

A theoretical development is presented which reformulates Fick&apos;s first law for diffusion in the solid state. The diffusion flux of component i in a multi-component system, Ji, is related to its local concentration, ci, and local jump frequency, ri : where a is a geometric factor and d is the jump distance. The product, ciri , is defined as the local concentration of atomic jumps for component i. The analog to Fick&apos;s second law is also derived. A solution to this equation is presented, which permits the experimental determination of the variation of atom jump frequency with composition in multicomponent systems. HISTORICALLY, the description of diffusion in the solid state has been presumed to be best approached as an application of more general diffusion laws, known as the phenomenological equations. These equations relate the flux, Ji, of the various components, expressed in atoms, grams, or volume, to the driving force involved, expressed as either a compositional or chemical potential gradient, sumption that the flux is simply proportional to the driving force is the foundation of this approach. The phenomenological equations take the form: where the concentration gradients are assumed to be the driving force, and: if the chemical potential gradient is taken as the driving force. The coefficients Dij in Eq. [1.] are the "diffusion coefficients"; the elements of the corresponding matrix in Eq. [2], the Mij, are called the "mobilities". Eqs. [I] and [2] may be considered to be definitions of these phenomenological coefficients. A formidable body of literature has been generated about these equations; this literature dates back to their original formulation for the simplest case of binary diffusion in a fluid, by Adolf Fick, in 1855.&apos; This description has been shown to be self-consistent. However, the "constants of proportionality", the Dij or ,Mij, are not constant: they vary with composition in all but the simplest systems. Even in the case of tracer diffusion, wherein it can be shown that the diffusion coefficient is constant, the mobility, which is considered in irreversible thermodynamics to be the more physically meaningful quantity, varies with the concentration of the tracer involved.&apos; In more complex systems, it is necessary to evaluate the entire matrix of phenomenological coefficients, as a function of composition, in order to describe diffusion locally. Further, in order to determine this matrix experimentally, it is necessary to produce diffusion couples that have different sequences of compositions; the matrix may be evaluated only at points where these "composition paths" cross.* Finally, and perhaps most

Jan 1, 1969

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951

J: H. POLHEMUS, New York, N. Y. (written discussion*).-The Joplin .mining and milling practice has largely influenced operating methods in the Wisconsin district. Milling equipment is essentially of the same type with the notable exception that no tables are used. The treatment of the flue &apos;sands has been attempted several times but without commercial success. Table material coming from any one mill is low both in tonnage and zinc content. The iron is comparatively high as the pyrite-line "chat" is much more prevalent than the zinc-lime attached particle. In the finer sizes the zinc occurs mainly as free mineral. These condi-tions make the production of good-grade table concentrates very diffi-cult. The accompanying tabulated results from several mill tests indi-cate the character of the mill tails. I think the average mill tails in the district assay nearer 1.5 per cent. zinc than under 1 per cent., as stated by Messrs. Boericke and Garnett.

Jan 10, 1919

By Bailey, Lewis Newton

Bailey, Lewis Newton, Master Engineer, Senior Oracle, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia, at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Ballamy, John H., Capt., 103d Engineers, killed in action near Fismes, Aug. 9, 1918. Burt, Andrew, died in active service, 1916. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, 4th University Co., Princess Patricia Regiment, killed in action early in the war. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M. killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers&apos; Reserve Corps, died in active service, Jan. 1,, 1918. Hall, William T., Capt., Royal Flying Corps, killed in action, May 19, 1917.

Jan 11, 1918

By Robert T. Hill

The successful completion, January 10,1901, by Capt. A. F. Lucas, of a well, near Beaumont, Texas, whereby an enormous flow, estimated at &apos;75,000 barrels a day, was obtained, opened a new oil-field in the United States, kindled a frenzy of exploitation and speculation, revolutionized the fuel industry of a large region, and brought gain to thousands of people. Even to-day, it is impossible to cast up the present results or to prognosticate the future influence of this event. It has caused the revival of attention in other localities where oil had been suspected, and exploration for oil throughout the Texas region. It has attracted notice to the mineral resources of the Texas region, and created an interest in the geological conditions of that great State. This State, which has increased in population and wealth, as recorded by every succeeding census, with leaps and bounds such as are exhibited by no other part of the Union, now stands fifth in population and first in productive wealth per capita. Its fields, pastures, forests and mines teem with raw material. The whole economic evolution of the State has gravitated toward a focal point where these products were available for the coming of the kiln, the machine and the factory. The only drawback to the prosperity of the State was the lack of an economic fuel, inferior coal costing an average of $5.00 per ton at the time of the Beaumont discovery. This

Jan 1, 1903

By L. L. McDaniel

During the past few years a nuinber of improvements in smelting and power equipment have been made at the Douglas smelter of the Phelps Dodge Corporation at Douglas, Ariz. In the summer of 1935 work was started on the first unit of a new reverberatory waste-heat boiler plant which ultimately was to furnish steam for a modern high-pressure power pIant. A second reverberatory waste-heat boiler unit

Jan 1, 1944

By G. R. Speich, S. A. Kulin

The isothermal formation of martensite at subzero temperatures has been studied in an austenitic stainless steel. The amount of martensite formed isothermally in a given time was found to follow a C-curve behavior with decreasing temperature. Since isothermal rnartensitic transformation occurs at temperatures above the true M. temperature of the olloy, the observed M. temperature is dependent on the cooling rate. It is believed that a general martensite theory must include the basic concepts of the strain embryo theory, and also the important role of thermal fluctuations. UNTIL recently the isothermal component of the martensitic transformation had been considered as a trivial effect in theoretical considerations of this type of transformation. One of the postulates used in defining a martensitic transformation was that the reaction was temperature dependent but not time dependent. Cohen and his associates1&apos;2 were the first to report the isothermal formation of mar-tensite. They obsel-ved the time dependency of the martensite reaction at room temperature in plain carbon steels and certain tool steels. They found that a small amount of additional transformation occurred after the specimen reached the quenching temperature and that the rate of this isothermal transformation decreased rapidly with time. These authors considered this phenomenon to be a "tailing-off" of the main athermal reaction. Kurdjumov and MaksimovaL 5 studied the isothermal formation of martensite at subatmospheric temperatures in steels containing 0.6 pct C-6 pct Mn, 1.6 pct C, and in an iron-base alloy containing 23 pct Ni and 3.4 pct Mn. In each case it was found that both the initial rate and the total amount of isothermal transformation exhibited sharp maxima with decreasing temperature. They stated that it was possible to completely suppress the martensitic transformation in the 0.6 pct C-6 pct Mn steel by drastic quenching in liquid nitrogen. They interpreted their results in terms of a thermally activated process. The maximum in the rate of nucleation vs. temperature curve was assumed to be a result of the temperature dependence of the rate of growth of the martensite plates. It has been demonstrated," however, that martensite plates can form with great rapidity even at temperatures approaching absolute zero. In addition," attempts to confirm the reported suppression of the martensitic transformation by rapid cooling of a 0.6 pct C-6 pct Mn steel have proved unsuccessful. On this basis, and on other theoretical grounds, the validity of some of Kurd-jumov&apos;s results and conclusions is open to serious question. Cohen, Machlin, and Paranjpe&apos; have proposed a theory of martensite formation based on the nucleation of strain embryos and a growth mechanism involving cooperative atomic displacements. According to this theory thermal fluctuations can make a strain embryo supercritical and thereby produce martensite isothermally. Das Gupta and Lement&apos; have investigated the isothermal formation of martensite in a 17 pct Cr-0.7 pct C steel at temperatures below the ambient. They found that partial suppression of the martensitic reaction occurred on quenching into liquid nitrogen. That part of the reaction which can be suppressed is taken to correspond to the isothermal rather than the athermal part of the rnartensitic transformation. The initial rate of isothermal transformation for this steel was found to go through a maximum with decreasing temperature. This is in conformity with the findings of Kurdjumov and Maksimova for the steels used in their investigation. Das Gupta and Lement conclude that isothermal martensite formation occurs by the nucleation of new plates and is always preceded by some athermal transformation. An iron-base alloy containing 14 pct Cr-9 pct Ni was used in this investigation to study further the kinetics of the austenite to martensite transforma-

Jan 1, 1953

By Ma Guang, Huang Jinshou

In this paper we briefly describe measuring techniques and their practical use in the mining industry of China. A strain coefficient matrix of triaxial strain cell for a flat ended borehole is also introduced.

Jan 1, 1983

By GEORGE W. HARHIS

IN the earlier period of anthracite-ruining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally operated under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit only. They were- not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes ; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation wits given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.` That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Nov 1, 1905

By J. M. Oblak, W. A. Owczarski

A cellular appearing recrystallization product formed by annealing a cold-worked nickel-base super-alloy at 1800°F has been studied by electron nzicroscopy. Prior to deformation, an equilibrium micro-structure of fcc matrix y and cuboidal ,,&apos;, Ni (Al, Ti), precipitates of CuzAu structure had been established by an age at 1825°F. The strain-free recrystallization cells consist of very large rodular y&apos; particles in a y matrix. They precipitate is oriented and coherent both before and after recrystallization. The results showed that y&apos; coarsening accompanies recrystallization at 1800°F. However, it does so as a secondary effect and does not necessarily take place at lower temperatures. The structural similarity of this reaction to cellular precipitation in other systems indicates that lattice strain may also play a significant role during some cellular precipitation reactions. THERE have been numerous microstructural investigations of recrystallization in single-phase materials but two-phase systems have received much less attention. The second phase can either remain inert or be altered along with the matrix during recrystallization. If the second phase is an oxidelm3 or a relatively inert pre~ipitate,~, recrystallization is retarded when the interparticle spacing is less than 1 p. Prior to the onset of recrystallization, these materials show a well-polygonized substructure with the subgrain size limited by the interparticle spacing. Since recrystallization by the motion of preexisting grain boundaries6 is not observed, retardation has been related to particle pinning of the subboundaries. This pinning prevents coalescence&apos; or growth8 of subgrains to a critical size (formation of a high-angle boundary) necessary to initiate recrystallization. In a material such as a nickel-base superalloy both y matrix and y&apos; precipitate are altered by the recrystallization reaction. Haessner et al.&apos; studied the recrystallization of a cold-rolled Ni-Cr-A1 alloy by electron microscopy. The material was initially cold-rolled in the supersaturated condition. upon annealing at 750°C, immediate precipitation of 7&apos;occurred. Presence of this 7&apos; greatly retarded the onset of recrystallization which eventually took place by the development of randomly oriented, strain-free grains. The original •/ was dissolved at the recrystallization interface and reprecipitated as oriented, coherent par-tiles in the new grain. Recrystallization caused a refinement of .)&apos; particle size. Recently ~hillips&apos;&apos; investigated recrystallization of Ni-12.7 at. pct Al. Reduction by cold rolling presumably elongated the p&apos; precipitate into lamellae that remained coherent with the matrix. After recrystallization at 600" to 750°C, there was no unusual change in y&apos; particle size al- though there was a tendency toward clustering along the prior rolling direction at 750°C. Above 750°C, the recrystallized grains were generally free of precipitate. Studies in the somewhat analogous Cu-3.23 wt pct CO" and Cu-2 wt pct&apos;2 systems demonstrated that the coherent cobalt-rich fcc precipitate in these alloys obstructed softening, initiation, and completion of recrystallization. The precipitates were deformed into lam~llae during rolling and those of diameter less than 250A remained coherent. Recrystallization took place by the growth of new grains into the recovered or poly-gonized material. In the first study," both matrix and precipitate reoriented in the same manner upon passage of the recrystallization interface. There was no change in particle size or morphology. Tanner and ~ervi,~ on the other hand, observed that motion of the recrystallization fronts was strongly hindered by the pinning action of coherent precipitates in the deformed material. Particles in contact with a pinned boundary coarsened and coalesced leaving a denuded zone in the unrecrystallized region. When the number of pinning points was sufficiently reduced by coalescence, the boundary swept past these particles and through the denuded zone. The authors1&apos; considered this as a variation of discontinuous precipitation with both chemical driving force and deformation strain energy contributing to recrystallization. Preliminary observations by the present authors had revealed that recrystallization in Udimet 700, a nickel-base superalloy, occurred in an entirely different manner. Optical metallography showed that the recrystallized product formed as cellular colonies containing coarse y&apos; particles elongated in the direction of cell growth. In this investigation the structural features of this reaction were investigated by transmission electron microscopy. EXPERIMENTAL PROCEDURE As-received I$-in. rounds of Udimet 700* were (wtpct) 18.4 15.2 4.95 4.42 3.43 0.06 0.031 0.14 Bal. solution-annealed for 4 hr at 2150" and then fast air-cooled. An initial y-~&apos; structure was established by a 4-hr age at 1825°F followed by a fast air,cool. Essentially the equilibrium volume fraction of ?&apos; at 1825°F is precipitated within 4 hr. Microstructural examination showed no measurable increase in the amount of precipitate after longer aging times. Deformation consisted of swaging to 52 pct RA with 6 pct reduction per pass at room temperature. To reduce the precipitation potential to a negligible amount, recrystallization anneals were conducted at 1800"~ (982"~). Microstructures were investigated by optical and transmission electron microscopy. To prepare foils for electron microscopy, the material was first sliced into 30-mil slabs parallel to the swaging direction. Discs were dimpled and electrolytically cut from

Jan 1, 1969

By Stuart Croasdale

NOT long ago I was called upon to conduct some experiments on the treatment of ores from the New Cornelia copper mine, Ajo mountains, Arizona, for the Calumet & Arizona Copper Co. The problem was a very interesting one and contained some unusual features. Incidental with this problem was the utilization of a large amount of low-grade pyrite in the Bisbee mines of the company, provided this could be accomplished by any feasible method. The New Cornelia mine is situated 45 miles south of Gila Bend, the nearest railroad point, on the Southern Pacific Railroad. It is about 160 miles, almost due west, from Tucson. This section is one of the most arid in the United States. The normal annual precipitation, as given by the United States Weather Bureau covering a period from 1870 to 1901, is 3 to 5 in. During June and July, 1913, the records kept by the company gave the following results. These are all I have available, but they show the enormous evaporation that can be expected, which may be a factor in leaching operations on a large scale.

Jan 8, 1914

By Richard W. Brummett, Robert L. Dubms

Located some 180 miles east of Los Angeles in Riverside County, California, the Eagle Mountain mine supplies iron ore concentrates for the Kaiser Steel Corporation steel plant in Fontana, California, and for export to Japan. Although the deposits were first discovered in the early 1890's, no production was realized from the area until 1948 when Kaiser Steel Corporation commenced operations. A part of the large Basin and Range province, the Eagle Mountain area's geologic column comprises a thick series of metasediments resting on Precambrian gneisses and schists that have been intruded by sill-like masses of porphyritic quartz monzonite. The metasediments are composed of three quartzite units that are separated by a schistose meta-arkose and by two ore zones. They have been folded into a large east-west trending anticlinal structure that extends completely across the Eagle Mountains. The iron ore deposits occur in two well-defined horizons in the metasedimentary series, and they are found only along the north limb of the major anticline. Host rocks for the ore zones were a series of limestones and dolomites with associated quartzites. Magnetite plus pyrite comprised the primary mineralization that formed many replacement lenses and stringers of ore within the ore zones. The primary ore has been oxidized to hematite and goethite in a broad zone at higher elevations in the deposits. Hydrothermal alteration formed actinolite- tremolite granofels, local phlogopite, and minor tourmaline in the ore zones. This alteration and the ore deposition seem related to the same magmatic event that formed the porphyritic quartz monzonite intrusion

Jan 1, 1968

By T. Sterry Hunt

Jan 1, 1891

By G. W. Josephson

SINCE the earliest years of recorded history the durability and protective qualities of asphalt and tar have been known and utilized. The mummies of early Egyptian kings were coated with asphaltic materials, and asphalt mastics were common in Babylon. However, according to various authorities, it was not until 1780 that the first forerunner of present-day composition roofing was discovered,1 and the large-scale expansion of the industry has taken place since 1900. HISTORICAL BACKGROUND Development was stimulated by the growing popularity of manufactured gas. The by-product tars from these operations accumulated in large waste piles that had no commercial value and were a source of annoyance and expense to the gas companies. These tars were offered at very attractive terms to anyone who would take them away, and the infant "composition" roofing industry benefited accordingly. At first the process consisted simply of dipping sheets of burlap or other fabric in a tank of molten tar or asphalt. The long strip of roofing was rolled up for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from near-by fires. It was found that by increasing the largest particle size to the maximum that could be successfully embedded, and by properly controlling the amount of smaller fractions retained in the grade so as to cover the asphalt completely a Nigh degree of resistance to fire was attained. Needless to say, in this early period asphaltic roofing needed such selling points to gain acceptance in a field dominated by wood, slate, and tile. When asphalt is protected from the sun&apos;s rays it is extremely durable, but when exposed to sunlight its surface is comparatively rapidly decomposed. Completely covering asphalt roofing with mineral surfacing protects the asphalt and adds materially to the life of the roof-conservatively, 500 per cent. Slate Granules In the production of split slate shingles a large quantity of waste slate is accumulated, as 60 to go per cent of the rock quarried is discarded. This waste was a continuing burden on the industry. Some was marketed as ground slate flour for filler in paint and linoleum, and there is a record that as early as 1906 two carloads of coarse screenings from slate flour were marketed as granules for surfacing roofing. This new field appeared to the slate pro-

Jan 1, 1944