Search Documents

By R. W. Fountain, W. D. Forgeng

A new constitutional diagram is presented for the cobalt-rich end of the cobalt-titaniurn system. The modifications result from the presence of a new, intermediate, fcc phase, ?, the existence and homogeneity limits of which were established by metallo-graphic and X-ray studies of alloys containing from about 3 to 30 pct Ti. The precipitation of the ? phase from supersaturated solid solution was studied by hardness and electrical resistivity measzsrements, and two distinct stages in the process were observed. COBALT forms the base for a number of precipitation -hardenable alloy systems which may be divided into two distinct categories of practical interest, a) those hardened by intermetallic compounds and b) those hardened by carbide formation. The precipitation of intermetallic compounds from solid solution in cobalt-rich alloys has, however, received very little attention. Although the phase diagrams for some binary systems capable of precipitation have been determined,' there is an almost complete lack of data on the property changes associated with the precipitation, and even less information on the kinetics of the reactions or morphology of the products. More information is available on the precipitation of carbides because of the practical significance in superalloys. A survey of cobalt binary phase diagrams suggested that the cobalt-titanium alloys might provide interesting and useful precipitation-hardenable alloys. The equilibrium diagram as proposed by Wallbaum2 is shown in Fig. 1. Köster and wagner3 have indicated that the maximum solubility of titanium in cobalt is about 10 pct at the eutectic temperature (1135oC), and this decreases to about 7.2 pct at room temperature. The temperature of the allotropic transformation in cobalt is lowered by the addition of titanium, about 5 pct being sufficient to retain the high-temperature fcc modification to room temperature. Wallbaum and Witte 4,5 have indicated that the precipitating phase in alloys containing up to about 29 pct Ti is Co2Ti, a hexagonal Laves phase of the MgNi, type. With slightly higher titanium contents, they also report a cubic modification of Co2Ti of the MgCu2-type Laves phase. Duwez and Taylor6 confirmed the existence of the hexagonal (MgNi2) modification but not the cubic (MgCuz) modification of Co2Ti and suggested that existence of the cubic form may have resulted from impurities in Wallbaum's alloys. In their work on Laves-type phases, Elliott and Rostoker 7 reported the cubic modification of Co,Ti, but did not confirm the existence of the hexagonal modification. However, Dwight8 in a discussion of the work of Eliott and Rostoker again showed the existence of both modifications of Co2Ti, a result which was confirmed at that time by Elliott and Rostoker. As a result of a study on the iron-cobalt-titanium system, Köster and Gellers suggested the existence of a Co3Ti phase isomorphous with Fe3Ti. Witte and Wallbaum,' however, established the fact that no compound, Fe3Ti, exists in the iron-titanium system, and in a later publication, wallbaum2 stated that Kitster and Geller's reasoning was not valid, and no compound, Co3Ti, exists. This conclusion was later acknowledged by Köster.10 Preliminary experiments by the present authors to determine the precipitation-hardening characteristics of the cobalt-rich, cobalt-titanium alloys re-

Jan 1, 1960

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

In the Ti-Cd system two intermediate phases, TiCd and Ti Cd, have been found and characterized by X-ray diffraction powder techniques. An earlier reference' had reported the existence of the compound Tisd. No structural details, however, were given nor was there any indication of the possible existence of other binary compounds. Studies of the solubility of titanium in liquid cadmium2 led to the discovery of both TiCd and Tisd. The solid phase in equilibrium with saturated solutions of titanium in liquid cadmium at temperatures below 620°C is TiCd, whereas TizCd is the equilibrium solid phase above 620°C. Both thermal analysis and X-ray studies show that a peritectic reaction between the y phase (~isd) and cadmium to form the 6 phase (Ti Cd) occurs at 620°C. X-ray diffraction powder photographs of material isolated from the ingots used in the solubility measurements as well as material prepared by a direct heat of the appropriate stoichiometric amounts of titanium and cadmium can be indexed on the basis of a tetragonal unit cell with a = 2.904 ± 0.002A, co = 8.954 * 0.004A, c/a = 3.083. No variation of lattice parameters indicative of a range of composition is evident. With four atoms in the unit cell the calculated density of the intermetallic is 7.05 g per cm3; the observed value is 7.07 g per cm3. The TiCd lattice is primitive as indicated by the fact that there are no systematic absences among hkl reflections. The absence of all hko reflections for which h + k = 2n + 1 is also evident. This systematic absence indicates the following two space groups, C\h — P4/n and D&~4/nmm; both groups, however, have the same two- and four-fold positions. Stoichiometry, symmetry and space group indicate two likely structure types. They are the PbO-litharge3 (B10) type and the Ti CU (B11) type. Spatial considerations favor the B11 structure with atoms placed in the following positions: 2Ti (c) 0, 1/2, Z; l/2, 0, Z 2Cd(c) 0, 1/2, Z; 1/2, 0, Z The TiCd structure may be summarily described as a layered structure in which double cadmium layers alternate with double titanium layers along the c-axis. The best agreement between calculated and observed intensities is obtained for the values ZTi = 0.608 and ZCd = 0.130. Calculated and observed powder intensities as well as other pertinent powder data are recorded in Table I. Interatomic distances for the proposed structure are recorded in Table II and are to be compared with the distances of closest approach for titanium and cad-

Jan 1, 1962

Geological and Natural History Survey of Wisconsin, The University of Wisconsin, Madison, Wis - E. F Bean, State Geologist. A complete list of publications of this Survey will be sent upon request Only a portion of the Bulletins and Maps fall within the scope of this directory, and most of them are available They are: Bulletin 4, Building and ornamental stones of Wisconsin (1898), $2 50, 6, Preliminary report on the copper-bearing rocks of Douglas County, and parts of Washburn and Bayfield counties (1901), 50 cents, 7, The clays and clay industries of Wisconsin (pt 1) (1901), 50 cents; 14, Report on lead and zinc deposits of Wisconsin (the report is out of print but the 18 maps which accompanied it can still be had) (1906), 20 cents (a series of six maps, supplementary to these (1909), may be had for 6 cents), 15, The clays of Wisconsin and their uses (1906), 50 cents; 16, The geology of north-central Wisconsin (1907), $2, 17, The abandoned shore lines of eastern Wisconsin (1907), 50 cents, 19, Zinc and lead deposits of the Upper Mississippi Valley (1907), 25 cents; 34, The limestone road materials of Wisconsin (1914), 50 cents, 35, Underground and surface water supplies of Wisconsin (1915), $150, 36, The physiography of Wisconsin (new edition now in press) (1916), $125, 41, A study of methods of mine assessments and valuation (1914), 50 cents; 44, Mineral land classification in parts of northwestern Wisconsin (1915), $5, 45, The peat resources of Wisconsin (1915), 50 cents, 46, Mineral

Jan 1, 1933

By D. W. Loucks

There is plenty of evidence to indicate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money: to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before, automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system.

Jan 1, 1949

By G. A. Hellstrand

IN 1915, H. A. Guess, Vice President of American Smelting & Refining Co., in charge of its Mining Department, learned that the Anglo-New-foundland Development Co., Ltd., a pulpwood and paper-mill enterprise, had found upon its large concession in Newfoundland, and had opened up by shaft to the third level and some drifting, a lenticular orebody indicat-ing about 100,000 tons, as an extremely fine-grained sulfide ore, averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn; and that having sent parcels of this ore to Minerals Separation, Ltd., and various other metallurgical testing concerns without obtaining any success in commercial separations thereon, had discontinued work thereon and let the workings fill. Mr. Guess wrote to the general manager of that company and obtained a few hundred pounds of the typical ore, which he sent to his company's metallurgical testing laboratory at Flat River, Mo., outlining various flotation tests desired thereon, in an endeavor to obtain separation into a commercial lead concentrate and a zinc concentrate. But the art of flotation had not then progressed far enough to treat such ore, the galena and zinc blende being so fine grained that grinding to about 300 mesh was required to release the mineral particles in their gangue. Mr. Guess had flotation and other tests continued upon this ore from time to time with whatever new reagents and flotation devices were evolved as time went on, and finally, in 1925, he succeeded in effecting in his company's testing plant, then at Wallace, Idaho, separations into lead concentrates and zinc concentrates of satisfactory commercial grade. Mr. Guess then proceeded to unwater, examine and sample the property and made with the owners a partnership operating agreement upon the mine itself and a considerable area surrounding it, and in the early summer of 1926 began to prospect for additional orebodies, utilizing for such prospecting geophysical methods, under the direction of Hans Lundberg, methods which up to that time had been little used in mining in the western hemisphere.. This geophysical work found two large flat-lying orebodies of a type precisely similar to the smaller body of the original discovery. The larger orebody, some 3500 ft. west of the original

Jan 1, 1934

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

By Charles Y. Clayton

Cast-steel runners, while not interesting from a commercial standpoint, furnish valuable material for microscopic study. Folcyl found not only the usual ingot structure, but zones of Widmannstättian structure, which he explains as due to differential crystallization. The writer, in examining nickel-steel runners, found a type of pro-eutectoid ferrite that is unusual and most probably new. The runner in question was 8.75 cm. (3.5 in.) in diameter and analyzed at its center 2.69 per cent. nickel and 0.350 per cent. carbe a and at its edge 2.62 per cent. nickel and 0.359 per cent. carbon. Th macrostruc-ture, which is the usual type, is shown in Figs. 1 and 2, which are a cross-section and the longitudinal surface, respectively. Slight segregat'ion of ferrite can be seen near the center of the segment and at other points near the edges of polyhedral grains. Stead's reagent brings out the dendritic structure within the grains as shown in Figs. 3 and 4. This texture is what would be expected of such a steel. Figs. 5 to 10 show the peculiar swirls of pro-eutectoid ferrite, the finding of which prompted this paper. These swirls, or eddies, if such a term can be applied, occur in all parts of the runner and in all parts of the individual grains. The upper left-hand figure shows this ferrite at a grain boundary; the middle left-hand figure shows the inner portion of a grain; and the lower left-hand figure shows these swirls at the edge of a grain which is also the outer edge of the runner. Straight-lined ferrite associated with swirls is found in the areas of Figs. 11 and 12. The texture of the carbon-bearing constituent of the runner is shown to some extent in Fig. 12, the pearlite being very fine or sorbitic. Higher magnification does not bring out any new features either in the peculiar ferrite or in the pearlite. Figs. 13 and 14, at 240 diameters, show the curved and straight-lined ferrite.

Jan 1, 1922

ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E Bessemer, Abbott, C. E., Fer¬gusson, V. Birmingham, Aldrich, T. H., Jr., Bowron, C. E., Bowron, J., Collord, G. L, Crockard, F. H., Davis, F. H, Dimmick, F. D., Hillman, Ludwig, C. P., McCarthy, M. E., McCormack, G B., McCrery, Ramsay, E., Shook, A. M. Car¬bon Hill, Pill, J. R. Coal City, Lydecker, I. S. Gannts Quarry, Hiller, E. Helena, Squire, J. Holt, Shook, J. \V. Huntsmlle, Moss. Lehigh, Toulmin. Oxmoor, Green¬amyer, A. G. Rock Run, Garvin, J. M. Sheffield, Miller, D. I. Woodward, Lodge, J., Woodward, A. H. ALASKA. Ellannar, Stevens, B. Fairbanks, Hamilton, A. L, Robe, L S. Hadley, John¬son, P. Jualin, Hoggatt, W. B. Juneau, Denby, Thane, B. L., Whipple, J. R. Katalla, Hampton, W. H. Ketchihan, Barber, J. C., Geiger, A. \V., Parker, J. L. Niblack, Finck, W. N., Niedling, B. B. Nome, Garfield, C. D. Tin Oity, Fay, A. H. Treadwell City, Kinzie, Stow, H. P. Valdez, Esterly, G. M., Hazelet.

Jan 1, 1910

By Harry K. Ihrig

THE hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1/8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was, necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes Co. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.11 The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 DESCRIPTION OF TEST METHOD The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1945

By Edgar C. Bain

Of the important phenomenon of the hardening of steel, Professor Sauveurl says: It would seem as if the methods used to date for the elucidation of this complex problem have yielded all they are capable of yielding and that further straining of these methods will only serve to confuse the issue, the point having been reached when this juggling, no matter how skilfully done, with allotropy, solid solutions, and strains is causing weariness without advancing the solution of the problem. The tendency of late has been to abandon the safer road of experimental facts and to enter the maze of excessive speculations, in which there is great danger of some becoming hopelessly lost. The conclusion seems warranted that new avenues of approach must be found if we are to obtain a correct answer to this apparent enigma. With some degree of fitness we may say this of other problems. It seems likely that one of the new avenues of approach to many metallo-graphic problems is the study of crystal structure, or more accurately, the atomic arrangement, by means of the x-ray spectrometer. The crystal structure of some materials has been carefully worked out by the mineralogist, but his methods are, in general, unsuited to commercial metals and a method that yields even better information is at hand as the result of work on the diffraction of x-rays by Laue and the Braggs2 and later by HullI3 St. John, and others. It should be understood that the contour of free crystals, which is the subject of measurements by the crystallographer, is the result of the atomic structure and, in general, bears a simple and obvious relation to it. The use of the x-ray spectrometer4 has been described frequently, so the procedure will not be given here.

Jan 1, 1923

By Edgar C. Bain

Of the important phenomenon of the hardening of steel, Professor Sauveurl says: It would seem as if the methods used to date for the elucidation of this complex problem have yielded all they are capable of yielding and that further straining of these methods will only serve to confuse the issue, the point having been reached when this juggling, no matter how skilfully done, with allotropy, solid solutions, and strains is causing weariness without advancing the solution of the problem. The tendency of late has been to abandon the safer road of experimental facts and to enter the maze of excessive speculations, in which there is great danger of some becoming hopelessly lost. The conclusion seems warranted that new avenues of approach must be found if we are to obtain a correct answer to this apparent enigma. With some degree of fitness we may say this of other problems. It seems likely that one of the new avenues of approach to many metallo-graphic problems is the study of crystal structure, or more accurately, the atomic arrangement, by means of the x-ray spectrometer. The crystal structure of some materials has been carefully worked out by the mineralogist, but his methods are, in general, unsuited to commercial metals and a method that yields even better information is at hand as the result of work on the diffraction of x-rays by Laue and the Braggs2 and later by HullI3 St. John, and others. It should be understood that the contour of free crystals, which is the subject of measurements by the crystallographer, is the result of the atomic structure and, in general, bears a simple and obvious relation to it. The use of the x-ray spectrometer4 has been described frequently, so the procedure will not be given here.

Jan 1, 1923

By Arthur Wilson, Frederick Carr

INTRODUCTION 1. The application of retreat longwall mining to the North American coal mining conditions is becoming more advantageous as more experience is gained. The productivity results being achieved and potential possible illustrates that this system can be keystone of future underground coal production. 2. In the American coal fields multi-entry is normally practiced as this allows profitable longwall development with existing equipment and systems. Difficulties are being experienced however in the longwall retreat phase by the collapse of multi-entry roadways and excessive use of supplemental support in the following panel tailgates. In some instances the headgate of an operating face can also be in difficulty. 3. Jim Walter Resources Mining Division is developed on a mining plan that calls for three retreat longwalls at each of its four deep mines which have varying depths of cover and immediate roof and floor conditions. The 63 Mine has experienced longwall entry difficulty and there were differing viewpoints with respect to the best development systems to adopt particularily regarding the number of entries and pillar sizes. In an attempt to reconcile these different points of view J.W.R. asked Dr. Wilson to examine the problem and this paper outlines the new approach developed.

Jan 1, 1983

Truman H. Aldrich W. Lawrence Austin W. S. Ayres John Henry Banks Wrn de L Benedict Andrew A Blair Walter M. Brodie H. H. Burden Charles Butters

Jan 1, 1932

By A. Brown

RAPIDLY rising world demand for mineral products has accelerated depletion of the more readily accessible ores, particularly those of premium grade. Operations must proceed at a faster rate to deeper horizons, where there are problems of ground control that restrict economic recovery of the mineral and introduce new hazards to mine personnel. For some of the new Canadian mining fields severe problems of ground stress are still in the future, but much of Canada's mineral output comes from well established mines that have reached considerable depths. It must also be anticipated that the depletion of premium grade ores will eventually necessitate mining low grade material at competitive cost, and unsolved problems of ground control can materially increase costs. Studies of ground stress phenomena in underground workings are therefore considered a present-day necessity, especially since these investigations must be a long-term effort owing to the highly complex nature of the problem and the difficulty of making full-scale observations. In recent years the Mines Branch of the Department of Mines and Technical Surveys in Canada has conducted such an investigation. This report of the work is primarily concerned with stress problems in some Canadian coal mines and, in particular, with mine bumps. Mines Branch investigations of this and related problems are carried out by a small team of mining engineers and physicists who, with assistance from geologists, pool their special skills in an integrated program. These Canadian investigations combine a field and laboratory approach. Since data obtained under contrasting mining conditions allow useful comparisons of ground behavior under stress, this article will present data gathered under a wide range of Canadian coal mining conditions. Two contrasting longwalls in eastern Canada will be discussed and two dissimilar pillar extraction operations in western Canada. Locale of Observations In eastern Canada observations are being made in the collieries at Springhill, Nova Scotia. The district's No. 2 mine, which has a history of bump occurrences dating back to 1917, is currently being worked at a depth of 4200 ft. The mining method is longwall retreating along the strike and the practice is to retreat three walls in line, each about 350 ft long. There is no machine cutting or shooting—the coal is hand-picked and hand-loaded onto face conveyors. There are three rows of hardwood chock block supports parallel to the coal face. These supports are built during the two daily coal loading shifts, and the rear line is withdrawn during the midnight shift. The goaves are partially packed by stone midwalls 12 ft wide which are built forward daily in step with the face advance. The seam dips at 15° and averages 9 ft of strong, well cleated bituminous coal enclosed in competent beds of shales, sandy shales, and sandstones of Carboniferous age. The bumps rarely disturb the retreating longwall faces but manifest themselves as violent upthrusts of pavement in the levels leading to the walls. Observations have also been made in Springhill's No. 6 mine, which operated in a 5-ft seam of coal at a depth of about 2500 ft. Although No. 6 mine was

Jan 1, 1959

By John M. Lovejoy

CURRENT production of petroleum on such a vast scale presents many interesting problems- the solutions of which are important not only to those directly interested in the business, but to the nation as a whole. The industry is relatively young. Until the discovers of the Lucas gusher at Spindletop in 1901 petroleum production had not exceeded 60,000,000 bbl. per year compared with 1,100,000,000 bbl. in 1936. In 36 years then, the modern oil business, production, transportation, refining, and marketing has developed. I will first present a brief history. of oil production as a background for consideration of the present situation.

Jan 1, 1937

[This paper was presented for the author, who is now in the National service, by H. M. Chance, and was illustrated by a working model built to the plans shown in the Bulletin, for February, 1918, p. 268. For more convenient operation, a small motor-driven centrifugal pump was attached to the overflow outlet (5, Fig. 1, p. 267) delivering to the inlet, 4. The pressure of ingoing water was then adjusted by a valve at 4, and was indicated by the column of water in a vertical glass tube connecting with the pressure chamber; an average pressure of 15 in. of water column was maintained during the demonstration. The sand used in the test was beach sand, which had simply been passed through a 20-mesh screen; about 45 per cent. was finer than 80 mesh. The circulation of water was at the rate of about 5 gal. per square foot per minute, and the rising velocity of the water in the box as a whole (not the velocity of the jets) was 6 in. per minute. At this consistency, the specific gravity of the fluid mass was between 1.55 and 1.60. Mr. Chance estimated that it would be possible to maintain a fluid mass of this consistency, 3 ft. deep, and with an area of 50 by 60 ft. with an expenditure of 15-hp. Mr. Chance then showed how a lump of coal would float on the fluid mass, and also made a separation of slate from coal on a small scale in a wire cage submerged momentarily in the fluid. The following demonstration relates to a matter not contained in the original paper, and was presented as of interest to the operators of cyanide and other lixiviation processes dealing with fluid mixtures of varying specific gravity.-Ed.]

Jan 4, 1918

By L. O. Storey

The McDermitt mine was found as a separate mercury ore-bearing occurrence approximately 305 m (1000 ft) northeasterly and in a different geologic setting from the old Cordero mine, which had been the district's major producer. The following briefly describes the discovery of the new deposit and the Placer Amex lnc. involvement. The Cordero mining property was under lease by Sierra Mineral Management from the owner Fred H. Lenway in February 1971, when the property was brought to the attention of Placer Amex Inc. (known at that time as American Exploration and Mining Co.) by Richard F. Hewlett of Sierra Mineral Management. The property was first examined by Amex geologists in the spring of 1971, who reported favorably on the project. During that year, Sierra Minerals Management had retained Dr. Larry Walters as a consultant. He proceeded to drill test mercury soils anomalies which he had found northeast of the old Cordero mine in an area overlain by recent alluvium and gravel. An area known as the D area was subsequently blocked out and ascribed a tonnage of about 18 1 kt (200,000 st) which occurs in the vicinity of the eastern edge of the currently defined McDermitt ore body. This mineralization was found in flat lying mercury-bearing lakebeds, unlike the steep structurally controlled ore which was mined in the old Cordero mine. It became apparent to Placer Amex that since the chances of much more extensive ore were good in such a geologic environment, additional exploration was warranted. A joint venture was formed in October 1972 by American Exploration and Mining Co. and Sierra Mineral Management to further explore the Cordero property. The project exploration was fully funded and managed by Amex. Sampling began by Placer Amex in the D area where an open trench had exposed the lakebed ore. Visible cinnabar could not account for the high-grade mercury assays taken from the trench, and an unknown mercury mineral was suspected. Subsequent work established the presence of a chlorine-bearing mercury sulfide which may have enriched the lakebeds as a secondary supergene mineral. Early identification of the mercury-bearing mineral corderoite (Hg3Cl2S,) aided in the geologic concepts for the ore occurrence and was helpful in exploring for the expansion of the D area. Corderoite was found occurring with cinnabar in the lakebeds, and in places it is a major contributor. Specimens of the unique ore were given to Dr. Eugene E. Foord and Dr. Pieter Berendsen at Stanford University, who subsequently identified the chemical and crystallographic makeup of the new mineral and described it for the first time as a naturally occurring substance. Metallurgical work on mercury recovery from the newly described mineral was carried out by the Placer Development Ltd. laboratories in Vancouver, and an acceptable recovery system was worked out together with a planned mill design. Step out drilling from the D area by Placer Amex Inc. encountered extensive flat lying lakebed ore. The McDermitt ore body, as subsequently defined by drilling, was found to contain 2.7 Mt (3 million st) of open pittable ore, containing approximately 5 kg/t (10 lb per st) Hg. The ore body gently dips to the north and is found lying mainly in claybeds just above an opalite breccia blanket which overlies the earlier volcanics. Some ore is also found in the opalite breccia. The mine and mill were constructed under an operating joint venture with Placer Amex Inc. and Sterling Mineral Ventures, and production began in June 1975 at the rate of 20,000 flasks per year. The mine is currently in progress.

Jan 1, 1985

By R. G. Jones, W. L. Kinney, R. E. Schilson, R. S. Wilson, G. A. Clark, H. Suralo

This paper describes the field opeturluns at the Fry in situ combustion project in Crawford County, 111. Field operations may be divided into three phases—-preliminary engineering studies of 1960 and 1961, ignition, and, finally, operation of the test. The Fry combustion project was a pilot test of cocur-rent in situ combustion on a 3.3-acre inverted five-spot. In the summer of 1960, air injection tests were conducted using old wells in the area and a new air injection well drilled especially for the test. In the summer of 1961, four new oil wells were drilled on a 3.3-acre pattern for the pilot test. All old wells in the near vicinity of the pilot test were abandoned to preclude any possibility of gas escaping to adjacent formations. A compressor plant was also installed at the test site in 1961. Air injection tests and other engineering studies were made. At the conclusion of these tests, ignition was accomplished with a 40 kw electrical igniter. Operation of the Fry combustion test was little different from the usual oilfield operation with the exception of the high rate of air injection. No difficulty was found with the openhole completion. There were no unusual corrosion or emulsion problems until bottom-hole temperatures exceeded 150F. Four cores were drilled into the burned-out portion of the reservoir with no mechanical difficulties. INTRODUCTION A cocurrent or conventional in situ combustion test was conducted on the Fry unit of the Marathon Oil Co., in Crawford County, Ill. Besides testing combustion in the Fry type of reservoir, the test was intended to evaluate various operating procedures. This paper presents a discussion of the Fry combustion test field operations. The geology of the reservoir and the test performance are discussed in other papers.'.' HISTORY OF THE FRY UNIT The Fry unit consists of 11 leases totaling 337 acres in an area in which oil was originally discovered in 1906. Production from this reservoir, as from all Robinson sand reservoirs in the area, was very high during the first few years. As the dissolved-gas energy was dissipated, early attempts to retard the decline consisted of vacuum, air, and gas repressuring, and recently, most of the area has been subjected to water flooding. Following early air repressuring, the Fry waterflood unit was formed and water flooding initiated in July, 1952. In the area in which the Fry combustion test was conducted, a peripheral water flood of a 160-acre area was developed as shown in Fig. 1. Between 1956 and 1960, it became apparent that the water flood was unsuccessfd. In looking for a suitable site for an in situ combustion test, the Marathon Oil Co. selected the Fry unit as possessing those features most desirable for such a research project. Field operations associated with the Fry combustion test began in the spring of 1960.

Jan 1, 1966

By O. N. Carlson, A. L. Eustice

The tensile properties of iodide vanadium were determined as a function of hydrogen concentration. It was shown that the presence of 10 ppm H is sufficient to cause embrittlement of vanadzum over a limited temperature range. The temperature of the observed ductility mininlum is approximately -l00°C, this being a function of strain rate and hydrogen concentration. The yield stress of hydrogenated vanadium is raised sharply in the brittle temperature range. THE present investigation was initiated to determine the effect of hydrogen on the tensile properties of high-purity vanadium as a function of temperature and the role of hydrogen in the brittle-ductile transition. Loomis and Carlson&apos; reported a change from ductile to brittle behavior in iodide vanadium at -110°C with a return of ductility at temperatures below -140°C. Vanadium wire containing 270 pprn of hydrogen was brittle at room temperature while wire containing 100 ppm was ductile under the same conditions. Roberts and Rogers&apos; reported a ductile-brittle-ductile fracture sequence in vanadium containing 400 to 600 ppm of hydrogen. Their data show that hydrogenated vanadium is ductile at 150"C, brittle at room temperature and ductile again at -196°C. Magnusson and Baldwin found a minimum in ductility in vanadium containing 80 ppm hydrogen from tensile tests performed at several strain rates. Information available on the vanadium-hydrogen equilibrium system4 is somewhat incomplete. The absorption of hydrogen is exothermic in accordance with the decline in solubility with rising temperature. The limit of solid solubility at temperatures below 400°C has not been determined due to the difficulties in obtaining equilibrium at these temperatures. Data on the hydrides of vanadium are rather limited. Roberts6 studied the structure of VD,., by neutron diffraction, and observed the ordering of the deuterium atoms below -65°C into a primitive cubic cell with a lattice constant about twice that of the disordered bcc vanadium solid solution. EXPERIMENTAL PROCEDURE Vanadium of 99.9 pct purity was prepared by the iodide refining process6 for use in this investigation. This vanadium contained the following analyzed impurities; <20 pprn calcium, 150 ppm carbon, 200 ppm chromium, 30 ppm copper, 10 ppm hydrogen, 200 ppm iron, <20 ppm magnesium, <20 ppm nickel, <5 ppm nitrogen, 150 ppm oxygen, <50 ppm silicon, and <20 ppm titanium. specimen Preparation—Tensile specimens were machined from swaged rods of iodide vanadium. The

Jan 1, 1962

By J. H. Swisher

The rate of internal sulfidation of austenitic Fe-Ti alloys in H2S-H2 gas mixtures is controlled primarily by sulfur diffusion, with counterdiffusion of titanium playing a minor role. At temperatures below 1100°C, enhanced diffusion along grain boundaries becomes important. The rate of internal sulfidation at 1300°C is approximately equal to the rate computed from the sulfur diffusion coefficient. The diffusion coefficient of titanium in y iron has been determined from electron microprobe traces in the base alloy near the subscale interface. The solubility of sulfur in Fe-Ti alloys has been measured in the temperature range from 1150° to 1300°C. The equilibrium sulfur content is found to increase with titanium content, due to the large effect of titanium on the activity coefficient of sulfur. The Ti-S interaction becomes stronger as the temperature decreases. TITANIUM as an alloying element in stainless steels is an effective scavenger for interstitial impurities, carbon in particular. Titanium is known to form stable sulfides; however extensive thermodynamic data on the Ti-S system are not available. Schindlerova and Buzek1 have shown that the Ti-S interaction in liquid iron is moderately strong. There have been no previous studies of the Ti-S interaction in solid iron. Internal sulfidation of Fe-Mn alloys was the subject of a recent investigation by Herrnstein.2 He found the rate of internal sulfidation to be an order of magnitude greater than predicted from available solubility and diffusivity data. A satisfactory explanation for the discrepancy could not be given. In the present study, the solubility of sulfur in austenitic Fe-Ti alloys was measured using a standard gas equilibration technique. Fe-Ti alloy specimens were also internally sulfidized. The rate of internal sulfidation was measured as a function of temperature and alloy composition. Supplementary electron micro-probe measurements were made to provide additional information on the nature of the internal sulfidation process. EXPERIMENTAL The starting materials were alloys containing 0.12, 0.24, 0.38, and 0.54 wt pct Ti. The alloys were made in an induction furnace by adding titanium to electrolytic iron that previously had been vacuum-carbon-deoxidized. The major impurity in the alloys as determined by chemical analysis was carbon. The carbon content of the alloys averaged about 100 ppm; metallic impurities were presented in concentrations of 50 ppm or less. Specimens were made in the form of flat plates, 0.03 by 2 by 4 cm for the equilibrium measurements and 0.5 by 1.5 by 3 cm for the rate measurements. The experiments were performed in a vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction tube. In the gas train, flow rates of the reacting gases were measured using capillary flow meters. The source of H2S was a mixture of approximately 2 pct H2S in H2, which was obtained in cylinders from the Matheson Co. A chemical analysis was provided with each cylinder. The H2-H2S mixture was diluted with additional hydrogen to obtain the desired ratio of H2S to H2, and the resulting mixture was diluted with 30 pct Ar to minimize thermal segregation of H2S in the furnace. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over Pas. The samples used in the solubility measurements were analyzed for sulfur by combustion and iodometric titration. The subscale thickness in the internally sulfidized samples was measured on a polished cross section, using a microscope with a micrometer stage. Electron microprobe traces for titanium in solution were made on several samples that had been internally sulfidized. A Cambridge microanalyzer was used, and the known titanium content at the center of the specimen was used as a calibration standard. The procedure for the microprobe measurements will be described further when the results are presented. RESULTS AND DISCUSSION Equilibrium Data. Fig. 1 shows the sulfur concentration as a function of gas composition for three alloys equilibrated at 1300°C. The dashed line is based on data published by Turkdogan, Ignatowicz, and pearson3 for pure iron. The breaks in the curves are the saturation points for the alloys. The fact that the initial slope decreases with increasing titanium content indicates that titanium interacts strongly with sulfur in solution. To obtain information on the composition of the precipitating sulfide phase, the measurements described in Fig. 1 were extended to higher sulfur partial pressures. These results are shown in Fig. 2. (The initial portions of the curves are reproduced from Fig. 1.) The highest PH2s /pH2 ratio used is believed to be below the ratio required for the formation of a liquid sulfide phase. Time series experiments were used to study the approach to equilibrium in the samples. It was found that equilibrium with the gas phase was reached in less than 4 hr at 1300°C.

Jan 1, 1969