Search Documents

By J. A. Herrick

FOR a long time, especially in Europe, heavy pieces of forgings, such as cannon, armor plates, marine shafting, etc., have been steadily augmented in size, more particularly since steel has been substituted for wrought iron. To keep pace with these forgings several, very large hammers have been, from time to time, erected. The most powerful and thoroughly appointed of all now in operation is that designed and built by Messrs. Schneider & Co. at their works at Creusot, and it is the design of this communication to give to the members of the Institute a concise description of this remarkable piece of mechanism, which I have taken from an article published in the Annales Industrielles. This hammer is rated nominally at 80-tons power, but its capacity is, in reality, far greater, as will be seen by the comparative figures given later. The complete plant, comprising the hammer, the cranes, the furnaces, and the building which shelters the whole, is distin-

Jan 1, 1880

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

By Alden B. Greninger

Many recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces—other than the unknown "plane of polish"; hence resort must be had to other means of determining orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.' The methods that have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods.² The disadvantages of these methods are numerous, chief among them being the time required to determine a complete orientation. No method proposed so far is wholly satisfactory for determining the orientation of a small macrograin within a polycrystalline aggregate.

Jan 1, 1935

By Alden B. Greninger

Many recent contributions in the field of theoretical metallography have been concerned with crystallographic definitions or descriptions of various phenomena. The lattice orientation of the crystal being studied must be known before such definitions can be made. Practically all the metallic crystals used do not have crystal faces—other than the unknown "plane of polish"; hence resort must be had to other means of determining orientations. Some use has been made of etch-figures, slip bands, optical properties, etc., for this purpose; but for accurate results, and because of the fewer restrictions to their use, the various X-ray methods have been the most satisfactory.' The methods that have been used may be divided into two general classes: (1) oscillation methods, and (2) transmission Laue methods.² The disadvantages of these methods are numerous, chief among them being the time required to determine a complete orientation. No method proposed so far is wholly satisfactory for determining the orientation of a small macrograin within a polycrystalline aggregate.

Jan 1, 1935

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By William P. Jones

THE consumption of sulphuric acid, one of the most important commodities in our modern industrial world, is often used as a barometer for industrial activity. The economics of acid manufacture are largely dependent upon the location of the place of consumption and the availability of raw materials in that locality. Sulphuric acid is made from SO,, oxygen from the air and water. Therefore the sulphur dioxide is the only raw material to be considered in an economic study. SO, can be obtained from almost any material containing inorganic sulphur, such as elemental sulphur, pyrites, coal, sour gas and oil, metallurgical gases, waste gases, or gypsum and anhydrite. Many tons of acid can also be reclaimed by the recovery and concentration of spent acids. The aim of this paper is to present a guide to the economic aspects to be considered when the installation of an acid plant is contemplated. It must be remembered that 1 ton of elemental sulphur produces 3 tons of sulphuric acid and that the shipping of sulphuric acid by tank car is very costly. The size of the plant must also be given careful consideration. For instance, operation of a plant producing 5 tons of acid per day might be warranted in Brazil or Pakistan, whereas economics usually favor buying quantities up to 50 tons per day for use within the United States. Elemental sulphur, when available at the low price of 1M4 per lb delivered at an acid plant, has always been the raw material most frequently used for sulphuric acid. All conditions favor its use at this price. The so-called sulphur shortage has been the subject of so many technical papers, magazine articles, and newspaper items during the past y6ar that it hardly seems necessary to mention it again, but a very brief review of the matter will serve as a foundation for the discussion that follows. There is no shortage of sulphur. Only a shortage of low-cost Frasch-mined brimstone exists today. Other more expensive sulphur-bearing materials are plentiful, both in the United States and abroad. The low cost of Frasch-mined brimstone has discouraged the development of higher cost sources. However, the approaching depletion of Gulf Coast dome deposits and the greatly increased demand for sulphur here and abroad have made it necessary for industry to prepare for conversion to utilize sulphur in other forms. For future planning this situation must be considered permanent and not temporary. This conclusion is based on the fact that although sulphur demand will continue to rise, the production of Frasch-mined sulphur probably will not increase greatly beyond its present level of about 5,000,000 long tons per year. The International Materials Conference in Washington estimates 1952 requirements of the free world at nearly 7 million long tons; and the Defense Production Administration has recently set a new goal for 8,400,000 long tons annual domestic production by 1955. The total sulphur equivalent produced in this country in 1950 was 6 million tons. What, then, are the alternatives for the manufacture of the vital chemical, sulphuric acid? Today about 85 pct of this country's sulphur, and nearly 50 pct of the world supply, comes from our Gulf Coast salt domes and is extracted from the earth by Frasch's hot water process. The Gulf Coast salt dome deposits have been the most important known natural deposits in the world, producing 90 million tons of sulphur during the past 50 years. However, at the present rate of extraction these deposits cannot be expected to last indefinitely. Pyrites Pyrites are, and have been for many years, the source of more than 50 pct of the world's sulphur requirements. The principal use, of course, is in the manufacture of sulphuric acid. The use of pyrites in the United States has diminished greatly because of the availability of low cost native sulphur, but pyrites have continued a major source of sulphur in many other countries. The most available pyrites for use in this country are in the form of lump pyritic ore and in mill tailings from flotation of other minerals such as lead, zinc, copper, gold, and silver. An important factor, when the use of pyrites for acid manufacture is being considered, is the disposal of calcine. A ton of sulphuric acid requires approximately ton of high-grade pyrite and results in 1/2 ton of calcine. If the calcine is a fairly pure oxide, free of harmful impurities, it can be used, after sintering, in an iron blast furnace burden. Its value might be as high as 15d per unit of Fe at the blast furnace; or possibly $10.00 per ton of sinter, if it assays 65 pct Fe. This might result in a credit of $4.00 per ton of acid if the sintering plant and blast furnace are both located adjacent to the acid plant. On the other hand, several factors must be considered before this credit can be realized, i.e., freight to blast furnace, availability of sintering facilities, methods of eliminating impurities, and the removal of valuable metal values. In some locations it would be most economical to dump the calcines.

Jan 1, 1953

By S. W. Ross

In 1936 a description of the plant (Fig 1) and process employed by the Electrolytic Zinc Co. of Australasia Ltd. for the recovery of zinc from zinc concentrate by the electrolytic process was prepared. † During the twelve years which have elapsed since the preparation of the earlier paper, several major changes in the metallurgy of the process have been introduced. It is the purpose of the present paper to give a general description of these changes and thus to bring up to date the description of the plant and process. Summary The major changes in Risdon practice since 1936 have been: 1. Replacement of two stage roasting by a preliminary roast followed by the flotation of all the leach residue and the roasting of the flotation concentrate. 2. Screening of all calcine fed to the pachucas. 3. Continuous leaching of calcine and improved classification of pachuca discharge. 4. Close control of hydrogen ion concentration during purification for iron removal. 5. Recovery of cobalt as a good grade oxide. 6. Production of part of the zinc output in the form of "four nines" metal (99.99 pct purity). 7. Closer spacing of electrodes thus increasing the potential output of cathode zinc per cell by 50 pct. Changes which are in prospect and for which construction work is proceeding at the present time involve the starting up of: 1. Two suspension roasters. 2. A contact acid plant to produce 150 tons‡ of acid per day and replacing the existing Mills Packard chamber plant. 3. Extra power station capacity to permit greater current flow to existing cell room units. This will increase the output of cathode zinc from about 245 to 290 tons per day. Plans for the future envisage the building of an ammonium sulphate plant, the first unit of which will produce about 50,000 tons per year, and improved treatment of zinc plant residue for the recovery of zinc, lead and other metals. At the end of this paper tables of metallurgical data are presented relating to the year ending June 30, 1948. Details of Changed Practice Output In 1936 the production of cathode zinc amounted to about 200 tons per day. This has since been increased to about 245 tons per day while plant extensions are practically complete which will permit of an output of about 290 tons per day in the near future. Roasting Division ROASTING POLICY A major change has occurred in the roasting policy. Twelve years ago the method in use was to carry out a two stage roast in the first stage of which sulphide sulphur was reduced to about 6 pct. The pre-roast calcine was re-roasted in modified Leggo furnaces using coal as fuel, sulphide sulphur being reduced to about 0.8 pct. The whole procedure was described on pp. 482491 of the earlier paper. Although this roasting procedure had certain advantages it possessed some distinct disadvantages. For instance, it appeared uneconomical to heat up the entire input of pre-roast calcine to roasting temperature by the expenditure of fuel in order to oxidise a few percent of sulphide sulphur. It was argued that if the pre-roast calcine were leached and a process could be developed for the recovery of a zinc sulphide concentrate from the leach residue, this concentrate, small in weight compared with the pre-roost calcine, would probably roast autogenously, thus virtually eliminating the expenditure of fuel as well as greatly increasing the weight of sulphur oxidised per square foot of furnace hearth area. The obvious method of producing a suitable concentrate from leach residue was by flotation. It will be recalled (see p. 495 of the earlier paper) that when two-stage roasting was practised the leach residue was classified, the granular fraction was ground and floated while the slime fraction was thickened, filtered and dried ready for shipment to a lead smelter. This process worked quite successfully. However, when trials were made of leaching a calcine carrying several percent of sulphide sulphur the granular fraction still floated well, but the slime fraction carrying 8-10 pct sulphide sulphur yielded very poor results when subjected to flotation. This fact held up the application of "pre-roast" leaching for many years. However, successful flotation of the slime fraction of leach residue was finally achieved and in August 1940 the slime flotation plant began operation, while the leach-

Jan 1, 1950

By John R. Low

A number of cases of low-temperature, intergranu2ar brittle fracture of metals containing small amounts of certain impurities, have now been identified. Some degree of understanding of this phenomenon exists for the simpler binary systems of a metal and a single impurity, but the profound effects of other impurities and alloying elements in modifying this type of behavior remain unexplained. Current research in this area is reviewed and some of the newer techniques of investigation which should make possible a more quantitative study of the structure and composition of grain boundaries in impure metals are described. To indicate the subject matter of this lecture, we may begin by reviewing the experimental observations concerning low-temperature intergranular brittleness in impure metals, particularly those examples in which the embrittlement appears to result from what has been called "equilibrium grain boundary segregation."' These are the systems in which it has been impossible, at least up to now, to detect the presence of any second phase film at the brittle interfaces. When second phase films are present they are usually readily detectable by fractographic methods, often appearing as epitaxial films in geometric or dendritic patterns. An example is shown in Fig. 1 for the case grain boundary carbides in a sensitized stainless steel which failed by intergranular brittle fracture at 78?k2 In contrast to this type of embrittlement there are numerous examples of low-temperature intergranular embrittlement in which the fractographs are essentially featureless, for example, that of an oxygen-embrittled iron shown in Fig. 2. The only second phase particles visible are the small, widely separated, round oxide particles typical of the bulk material. The fracture surface is extremely smooth and the fracture path appears to follow the intergranular interface without deviation. This type of fractograph also implies that crack propagation has occurred without plastic deformation at the crack tip, since localized slip or twinning ahead of the crack would be expected to distort the interface and be readily visible in the fractograph. Such indications are occasionally seen in these fractographs, but are not characteristic. A second example of this type of fractograph is shown in Fig. 3, which is from a temper-embrittled, carbon-free, Fe-Cr-Ni alloy containing Sb, broken at 1OO?C.3 The similarity to the oxygen embrittled iron case will be apparent. In the case of the temper embrittled Cr-Ni ferrite containing antimony, it is possible to remove the embrittlement by suitable thermal treatment. The grain boundaries may then be examined by thin film transmission in the electron microscope for the material in both the nonembrittled condition and in the embrittled condition. Two boundaries are shown in dark-field transmission in Fig. 4, one in the nonembrittled

Jan 1, 1970

By Nelson P. Hulst

To those who have had the happy privilege of friendship with George W. Goetz, the announcement of his death has brought great sadness. He was born in Milwaukee, Wisconsin, February 17, 1855, and died January 15, 1897. In his boyhood days, when I first came to know him, his frank, trustful manner; his eyes brimming with truthfulness; his eagerness, never obtrusive, to gain knowledge from all whom he met; and his equal readiness to give without ostentation of his store, constituted a personality which at once commanded confidence and won friendship. I am told that as a scholar of five years he was conspicuous for brightness, a show-pupil, who was called on to recite when visitors were present at school. Yet this in no way spoiled him. His modesty was too strong a trait in his character to be overcome by any attention which might, be expected to arouse vanity. In his simple-heartedness he was pleased then, as he always was in his maturer years, to give of his knowledge for the gratification of his listeners, with never a thought of himself. So strong was this characteristic that in a brief autobiography, in the form of a letter to his wife and children, found among his papers, he excuses himself to them for recounting what he had accomplished in his life-work. As a preface to this autobiography (which, it seems, was prepared on the eve of a sudden journey to California, taken February, 1895, for his health) he says: " I am writing this rather hastily, and I

Jan 1, 1898

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By Theodor Zuschlag

Electrical prospecting is the art of exploring the structure of the subsoil in regard to conductivity variations and interpreting the results of such exploration as to their geological meaning. Electrical prospecting has been applied during the last few years with outstanding success, not only to prospecting1 for ore but also to structural studies.2 Both applications have proved helpful to the geologist, and the latter application especially promises to become of still greater importance in the future. The mapping of structures is the most important function of the oil geologist. Oil is lighter than water, therefore in water-bearing beds it will migrate upward until the migration is stopped by a bed impermeable to the oil. Geologic structures such as domes, anticlines, faults and terraces, offer good prospects in the search for oil accumulations and can be traced easily by electrical prospecting, provided they are composed of a series of sedimentary layers of which at least one possesses fair electrical conductivity and follows the general trend of the structure. Conditions for Successful Mapping The first condition, fair electrical conductivity, is met in almost any oil-bearing series, because generally the electrical resistance of a sedimentary bed is identical with the resistance of the more or less saline waters, filling partly or entirely the pores of the rocks.3 Briefly, the electrical resistivity of a bed can be expressed for all practical purposes by the product R X P, where R is the specific resistance of the waters in the rock pores and P a factor depending upon the percentage of water by volume in the rock. The specific resistance of any solution can be computed from the chemical analysis, being primarily a function of the

Jan 1, 1932

By Joseph Singewald

INTRODUCTION FOR a number of years Russia, India and Brazil have outranked .all other countries as producers of manganese ores. During the 5 years immediately preceding the European war, the average annual production of Russia was 844,000, of India 694,000 and of Brazil 200,000 long tons. Since the outbreak of the war there has been a considerable falling off in the Russian and Indian production, particularly in the former, whereas the production of Brazilian ores has been greatly increased, amounting in 1914 to over 250,000 tons and in 1915 to nearly 350,000, with conditions favorable for a still larger production in 1916. Manganese is one of the few industrially important metals that are not produced in the United States in quantity commensurate with our needs, so that we have been compelled to import annually about 300,000 tons, having a value of over $2,000,000, and these ores have been obtained from the three countries mentioned above. Their rank as contributors to our imports of manganese ores was India, Russia, Brazil; and in 1913, Brazil contributed only one-fifth. During the past 2 years Brazil has furnished rapidly increasing quantities to this country, and, with the falling off of imports from India and Russia, has become our principal foreign source. In 1914, Brazil furnished two-fifths of the imports and more than India or Russia, and in 1915 over nine-tenths. The manganese ores of Brazil are consequently of more than usual interest to us at this time.

Jan 10, 1916

MORE than 5000 miners and suppliers descended upon Denver to make the American Mining Congress' four-day metal mining show one of the most extravagant equipment displays ever assembled in one place at one time. The most recent developments in equipment for mining, milling, and processing ore were shown by the 146 exhibitors at Denver's new City Auditorium which covers 57,000 sq ft of floor space. Other displays were placed in the open air opposite the auditorium site. Registration desks were opened Sunday, Sept. 21. A field trip to the Colorado School of Mines at Golden was the featured activity of the day. Official opening of the show took place on Monday, and presided over by Howard I. Young, president of American Zinc, Lead & Smelting Co.; Otto Herres, vice president, Combined Metals Reduction Co.; William J. Coulter, vice president, Climax Molybdenum Co.; Charles B. Stainback, Westinghouse Electric Corp.; and Merrill E. Shoup, president, Golden Cycle Corp. Convention welcoming addresses were delivered by a representative of Mayor James Q. Newton, of Denver, and Gov. Daniel V. Thorton of Colorado. Following the formal opening ceremonies a round table discussion dealt with the "Paley Commission Report" formally called Resources for Freedom. Participating in the panel were: Arthur H. Bunker and George R. Brown, members of the Paley commission; H. I. Young, president of the American Mining Congress; Horace M. Albright, president of U. S. Potash Co.; Evan Just, vice president, Cyprus Mines Corp.; Donald H. McLaughlin, president, Homestake Mining Co.; E. H. Snyder, president Combined Metals Reduction Co.; Simon D. Strauss, vice president, American Smelting & Refining Co.; Sen. H. C. Dworshak (R.-Idaho) ; Ira B. Joralemon, consulting engineer; Jess Larson, De fense Materials Procurement Agency; and Andrew Fletcher, president of St. Joseph Lead Co. The panel discussed the report for six hours, adding a great deal of information to the already voluminous amount which has been gathered concerning it. Three objections to the report frequently mentioned were: 1-the multilateral contract; 2-international buffer stocks; 3-international buffer stocks combined with limited quota arrangements. Points on which the panel commended the report were its recommendations for acceleration of topographic and geologic mapping of the United States and Alaska; recognition of the principle of percentage depletion for metals and minerals; and advocation of removal of the present limitations on the expensing of exploration costs applicable to minerals. Technical sessions were held throughout the four days of the meeting. Included in the program were: Progress in Mechanication; Small Mines; Public Lands; Open Pit Mining; Manpower-Labor Relations; Shaft Sinking; Roof Support; Taxation, Gold, Silver and Monetary Policy; Advances in Mill Practices; Special Conference on Strategic Materials; Uranium Mining-Atomic Energy; Prospecting and Exploration; New Metallurgical Processes; and Rock Breaking. About 45 papers and several panels were presented during technical sessions. Formal and informal social functions consumed the remaining time of the convention. Three locations were needed to handle the huge throng attending the Mining Jamboree Monday evening. The only other sponsored social function took place Thursday evening. A great many informal gatherings, chiefly convivial, were held in manufacturers' courtesy rooms-called wet stopes. Field trips included Cripple Creek, Pueblo, Climax -Leadville-Gilman, Colorado Plateau-Grand

Jan 1, 1952

By R. A. Meussner, C. T. Fujii

Chromium solution in wustite depresses the oxygen activity in a nonideal manner and expands the lattice slightly. Gravimetric measurements of the equilibrium compositions of wustite containing 0.00 to 1.38 wt pct Cr define the oxygen potential (CO2-CO atm) and the limits of the phase field at 1000°C. These data extrapolate to a maximum solubility of 2 wt pct Cr. The lattice parameter data, room-temperature measurements of quenched samples, differ significantly from those in the literature. Both pure and chromium wus-tites contract at uniform and equal rates as the oxygen content (metal deficit) increases. The a. US metal deficit relationships are straight lines showing none of the curvature previously reported. At constant metal deficit, the a. expands by 0.002? on alloying with 0.4 to 0.5 wt pct Cr but is insensitive to further chromium additions: a small expansion rather than a marked contraction. These results require a modification of the accepted alloying mechanism. IN the high-temperature oxidation of Fe-Cr alloys in Ha-H,and CO2-CO atmospheres the vapor transfer of oxygen from the continuous wustite outer scale to the porous inner scale/alloy interface sustains the high oxidation rates.1"3 The driving force for this transport is the difference in the oxygen activity of the outer wustite and that at the inner scale/alloy interface. In pure CO2, as well as in CO2-CO atmospheres, carburization of the alloy accompanies this oxidation. Current efforts to evaluate the parameters controlling this carburization have shown that the process is not simple; i.e., the carbon concentration in the alloy initially increases rapidly, reaches a maximum, and then decreases slowly as the oxidation time is extended. This is the same pattern reported by McCoy for the more complex oxidation-carburization of stainless steels and an Fe-Cr alloy in CO2 at lower temperatures.4 These changes in the carburization process occur while the overall oxidation rate and the lattice parameters of the scale layers remain constant. If this invariance of the lattice parameter is assumed to indicate a constant scale composition and thus a constant oxygen potential, the carburization results are not easily explained. Electron microprobe traces across the thickness of these outer scales, however, have revealed distinct chromium gradients penetrating 10 to 50 µ from the inner surface where the chromium concentrations were estimated at a few tenths percent. The variation of the chromium cmcentration on the inner surface of the scale, and the resulting change of the oxygen activity, during the oxidation process is considered to be important in defining the carburization process. Thus, to gain an understanding of the complex oxidation-carburization proc- ess, it was necessary to measure the properties of wustite containing known amounts of chromium (chromium wustite). Although the general features of the Fe-Cr-0 equilibrium diagram between 900° and 1300°C have been fairly well established by Richards and white: Wood-house and White,6 Seybolt,7 and Katsura and Muan,8 there have been no detailed studies of the limits of the chromium wustite phase field or the properties of these alloyed wustites. The recent results of a limited study of chromium wustite by Levin and wagner9 indicate that more than 0.67 wt pct Cr is soluble in wustite above 850°C and that this alloying is accompanied by a substantial lattice contraction. This change in the lattice parameter was not evident in the X-ray diffraction patterns of wustite layers from the oxidation experiments;1,3 the lines were sharp even though a chromium gradient existed in the scale. The present paper describes gravimetric equilibrium experiments which delineate the boundaries of the chromium wustite single-phase field at 1000°C and define the changes in the oxygen activity and the lattice parameter of wustite as functions of chromium and oxygen contents. The lattice parameter data of chromium wustite obtained from these equilibrium and special quenching experiments differ considerably from those reported.9 Those for pure wustite show significant differences from the widely accepted data of Jette and Foote.10 Since the causes of these differences are not easily assignable, and since the literature contains many sets of data on wustite which if not in conflict are at best not in harmony, the experimental procedures are discussed in the present paper. EXPERIMENTAL Oxide Preparation. The specimens used in these studies were porous pellets compacted from high-purity (Fe,Cr)2O3 or Fe2O3 powders. These powders were prepared from electrolytic chromium (99.8 pct purity) and electrolytic iron purified by consumable-electrode, vacuum arc-melting processing (299.9 pct purity).11 The oxides were produced by standard analytical procedures: solution of the metals in acids (HC1, then HNO3 added), coprecipitation of the hydroxides (NHaOH), and filtering and washing these precipitates. Initial dehydration of the coprecipitated hydroxides was done in a porcelain evaporating dish heated by a Meker-type burner, final dehydration by firing in a recrystallized alumina crucible at 1000" to 1050°C for 20 hr in an electrically heated furnace. Spectrographic analysis detected the following impurities: silicon, 0.01 pct or less; aluminum, 0.001 pct to trace; manganese and copper, 0.0001 pct to none. Each of these levels is at least one order of magnitude lower than in commercially available CP grade ferric and chromic oxides. Fluorescence analy-

Jan 1, 1969

By F. M. Lewis, J. F. Myers

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By J. F. Myers, F. M. Lewis

The selection of the proper type of flotation machine involves the consideration of a wide variety of factors. Under any condition, all types of machines will promote some kind of separation. Obviously, the correct way of deciding which type of machine is best suited for a particular problem would be to set up all types of machines and test them out in a competitive manner, but the vast number of small concentrating plants are unable to make such complete and exhaustive tests. The experience of the authors of this paper indicates that if all the factors involved in any particular problem can be determined, and if all the flotation-machine characteristics are understood, some basis for selection could be arrived at other than actual comparison. This paper is presented to show how the process factors and machine characteristics have been combined at the mills of the Tennessee Copper Co. from studies of several types of flotation machines. At the two mills of the Tennessee Copper Co. in the Ducktown Basin of Tennessee, four distinct flotation separations are made on the complex sulphide ore. Three different concentrates are produced from the ore—in the order of their importance: iron concentrate, copper concentrate, and zinc concentrate. Four different types of flotation machines are used. The selection of these four machines, for the plant operation, was based upon the study and operating experience of the machine units shown in the following list: Fagergren machine; square cell, size 56 inches Fagergren machine; level type, size 56 inches Denver machine; conical disk impeller, size 24 inches Denver machine; receded disk impeller, size 24 inches Minerals Separation Sub-A, size 24 inches Munro-Pearse deep cell, pneumatic Southwestern air machine, Hunt principle To date the study of flotation machines has been confined almost entirely to the rougher circuits. The various cleaning operations, being relatively a much simpler matter, have not been investigated so thoroughly. Table I shows a typical analysis of the two ores as well as of the mineral content.

Jan 1, 1947

By Armando M. Lago

Secular and cyclical patterns of postwar sources and uses of funds of the mineral sector are analyzed. A simultaneous equation behavior model of sources and uses of funds is developed for both mining firms and integrated producers, and these models were put through the task of predicting the financial and expenditure be-havior of mineral corporations in response to mergers and changes in investment tax credits and depletion allowances. Finally, the quantitative analysis methodology is applied to the analysis of optimum capital structure of mining corporations. The postwar changes that have occurred in the expenditure and financial behavior of mineral corporations are reviewed, particularly the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail. An econometric model of mineral corporate financial behavior is formulated. This model is then estimated and reviewed. Policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector are discussed. Finally, the optimum financial structure of mining firms is discussed and the effect of corporate financial structure on the mining corporations' average cost of capital is analyzed.

Jan 1, 1971

By J. R. Sturgul, J. C. Wynn

Computers and computer applications in geophysics are fairly recent innovations. The area of data handling is one that has found many immediate applications. Initially, the use of computers involved in almost all cases, a batch-input arrangement requiring a trip to the local computer center, a wait and another trip. Even though the computer worked at incredible speeds, the time-delays, in case an error in the input data developed, often could be several days. Use of computers in mining exploration by medium-sized or small-sized companies and contractors has been almost non-existent beyond simple data reduction work. The principle J. R. Sturgul, SME member, and J. C. Wynn, both affiliated with the Dept. of Geosciences, University of Arizona, Tucson, presented this paper at the Eleventh International Symposium on Computer Applications in the Minerals Industry, reasons appear to be the time factor and the inconvenience of the frequent trips involved. With the advent of time sharing systems, whereby a company need only have access to a terminal, the main objections can be overcome. An Apparent Solution An apparent solution to the time and distance inconveniences which would permit more extensive use of computers in geophysical exploration, is to buy or lease/purchase a medium-sized computer and install it in or near one's office. This is a formidable proposition in terms of cost and programming time on both respects, but several mining companies of larger size have already gone this route. In most cases, the computers have been expensive devices with a limited memory or core size. For routine data handling this memory size is not restrictive; however, for many geophysical applications such as three-dimensional modeling this can be critical.

Jan 10, 1973

By J. T. Crawford

Although nearly 10 pct of the total tonnage of coal produced annually within the United States is handled by bulk freighters on the Great Lakes, very little of the detail connected with it has been published other than occasional newspaper stories and publication of tonnage statistics. Of the total tonnage floated on the Lakes each year some 10,000,000 is stored and distributed from the port of Duluth-Superior, at the western end of Lake Superior commonly known as the Head of the Lakes. This port has the largest single area concentration of coal docks in the world. Since this area contains the largest ore docks, the largest movable material handling bridge, the largest and highest grain elevator and the largest coal bri-quetting plant in the world, it is entirely fitting and proper that here also should be located the largest coal dock and what we believe to be the world's largest clam shell. Of the sixteen coal docks operated by ten companies, five are owned and operated by the North Western-Hanna Fuel Co. which has two docks on the Superior, Wis., waterfront and three docks in Duluth, Minn. It is with these five docks that we are primarily concerned, General History In the summer of 1871 a small sailing vessel entered the harbor of Duluth-Superior with the first commercial coal cargo. All the coal brought up that first year did not amount to more than 3000 tons. During the year 1877 the first dock equipped for handling coal was built in Duluth. Coal receipts increased to 52,785 tons in 1879 the first year for which an official record was kept. Since then the volume of water-borne coal to the Head of the Lakes steadily increased to a maximum of 12,688,321 tons in the year 1923. This tonnage was nearly equalled in the year 1927 and the next highest tonnage recent year was in 1946 when 10,105,703 tons were unloaded. The average annual bring-up over a ten year period 1938 to 1947 was 8,605,231 tons. Approximately 30 pct of the coal unloaded at the Head of the Lakes is handled over the docks of the North Western-Hanna Fuel Co. Competition of other fuels coupled with expansion of coal fields in the mid-west have held coal receipts for Duluth-Superior at a relatively constant figure during the last eight years although the total tonnage of coal floated on the Great Lakes has more than doubled in the past 25 years. From the shovel and wheelbarrow method of unloading early cargoes to the horsepowered windlass derrick with a wooden tub was but a short step. The first movable coal handling, steam operated,

Jan 1, 1949