Search Documents

By M. S. Seltzer

High temperature steady-state creep rates have been determined jor lead sulfide single crystals whose defect concentrations were fixed by equilibration under controlled sulfur pressure. The activation energy of creep, Qc , for undoped lead sulfide, is a function 01 composilion, decreasing from 2.9 to 2.2 ev as the carrier concentration increases from 9 x 1016 to 8 1018 electrons cm-3 for lead excess crystals, and increasing from 1.7 to 2.3 ev as the concentration of holes increases from 4 x 1017 to 1 x 1018 cm-3 in sulfur excess material. For five different composilions, Qc for undoped and bismuth-doped crystals has been found to be equal to Qpb + Qs, the self-diffusion activation energies for lead and sulfur in PbS. It is well-established1 that high-temperature steady-state creep of pure metals is a diffusion-controlled process, where the activation energy of creep is equal, within experimental error, to the activation energy of self-diffusion. The relationship between the activation energy for steady-state creep and those for self-diffusion in binary compounds is more complicated, however, because two different diffusing species must be considered, and becayse the activation energies may be influenced by compositional variations and by foreign atom additions.2-4 In some cases experimentally determined creep activation energies are correlated with those for self-diffusion of the slower-moving species, but such agreement is by no means universal. Interpretation of experimental results is difficult because few investigations include measurements of creep rates and self-diffusion coefficients of both diffusing species on single crystals of similar composition and foreign atom concentration. The objective of this investigation, therefore, is to determine the influence of stoichiometric defects and foreign atoms on steady-state creep and self-diffusion for a well-characterized binary compound. Lead sulfide, a compound semiconductor which crystallizes in the NaC1-type structure, and whose homogeneity range includes compositions on either side of the 1:l atom ratio, was chosen for study in this investigation. The pressure-temperature-composition relations for PbS are available,5,3 and deviations from stoichiometry may be monitored by electrical measurements.7 Single-crystal specimens are available to allow observation of effects due to bulk phenomena without interference from grain-boundary effects. These crystals have been employed to determine steady-state creep rates under compressive stress for "pure" and bismuth-doped PbS as a function of sulfur pressure and temperature as well as crystal orientation and applied stress in order to establish the relationships between defect concentrations and creep rates. EXPERIMENTAL PROCEDURES Crystal Growth. Lead sulfide crystals, prepared by the Bridgman method, are grown in evacuated quartz crucibles, filled with almost equal atomic proportions of high-purity (99.999 pct) lead and sulfur, and heated to a temperature above the melting point of PbS (about 1127°C) so that the lead and sulfur react to form molten PbS. The crucible and melt are dropped through the hot zone of the crystal-growing furnace at the rate of 1 cm per hr. The maximum melting point of PbS is slightly on the lead-rich side of the 50:50 composition; hence crystals grown from a near stoichiometric melt are usually n-type semiconductors containing excess lead atoms. Typically the lead excess concentration in solid solution with the PbS is 3 x 1018 atoms cm-3. Crystals containing either 1/20 or 1/2 mole pct Bi2S3 were prepared by addition of the foreign atoms prior to crystal synthesis. Preparation of Specimens of Controlled Stoichiom-etry. Since it is difficult to grow crystals of desired composition, the process of crystal growth and control of stoichiometry are separated into two distinct operations. Equilibration of as-grown PbS to a desired composition is most easily accomplished by first annealing the n-type crystals under high sulfur pressure (about 1 atm) at temperatures above 700°C. This process serves to put excess lead precipitates into solution, yielding 0 -type crystals upon quenching to room temperature. Inter diffusion occurs readily in crystals so treated, and the methods described by Bloem may then be employed to obtain crystals of controlled stoi-chiometry. For the creep measurements made in this study, this involves heating crystals in mixtures of H2 and H2S The equilibrium constant for H2S is given by: Thus the sulfur partial pressure is obtained from knowledge of the H2/H2S ratio and Kh2S for the temperature in question. Fig. 1 shows the p-T-x diagram for PbS. It can be seen that, within the stability limits for single-phase lead sulfide, desired compositions may be obtained by equilibrating under a specified sulfur pressure and temperature. Characterization of Crystals. The principal methods for evaluating PbS crystals include measurement of electrical properties and mass-spectrographic analysis. The measured electrical parameters include Hall coefficient, conductivity type, and electrical resistivity Bloem7 has shown that there is a 1:l relation between the defect concentration and carrier concentration obtained. Hence, if the contribution to the carrier con-

Jan 1, 1968

By Robert Wamsley, W. E. Jones

ONE of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available, because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide, about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers. The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at-Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1945

By F. O. Shuck, F. E. Butler

A diaphragm diffusion cell suitable for use with liquid metals was designed and tested by measuring the diffusion coefficients for a Hg-10 pct In alloy at 25°C. The binary diffusion coefficient and the coefficients for In and Hg tracers were measured at this composition. The measured coefficients for both tracers were less than the binary diffusion coefficient. When these coefficients were combined with the activity correction term of Darken, the predicted binary coefficient was somewhat higher than the experimental value. In recent years a number of investigators have been studying diffusion of liquid metals in order to gain a better understanding of the liquid state and to examine possible applications to liquid metal processing. The bulk of this work has involved either self-diffusion or diffusion of low concentrations of solute metals in an essentially pure solvent metal. The most common experimental technique employed has been the capillary-reservoir method of Anderson and saddington1 since it is well-suited to measurements involving low concentrations of solutes. As an expansion of previous studies, an investigation of the variation of diffusion coefficient over large composition ranges has been undertaken in this laboratory. Although it is possible to modify the capillary-reservoir method for such measurements, the technique loses its principal advantage of requiring only small quantities of solutes. Therefore, it was felt desirable to investigate other possible experimental techniques applicable to measurements over large composition ranges. A technique which has been used widely in measurements of other liquid systems and seemed potentially applicable to studies of liquid metals was the diaphragm cell. This method has been found to combine relative simplicity of operation with accurate and reproducible results. In use with normal liquids, the tyiical diaphragm cell utilizes a porous glass disk. However, because of the high surface tension, it is not possible to use a diaphragm of such fine pore structure with liquid metals. Furthermore. projected use at high temperatures makes the use of glass undesirable. Consequently, the first problem was the search for an appropriate cell design. EXPERLMENTAL Diaphragm Cell. A number of possible cell designs were examined. Prototypes of several were constructed and tested. The final design is shown in an exploded view in Fig. 1. The cell consists of two identical chambers, one on either side of a 0.20-in.-thick partition. The chambers are 0.15 in. deep and have a volume of 3.45 cu cm. Each chamber is provided with two small threaded holes for filling and emptying. The filling holes may be sealed with stainless-steel screws. Drilled lengthwise through the center partition is a 0.250-in.-diam hole. Inserted into this hole is a rod having seven 0.059-in.-diam holes drilled radially through it. The total "hole" volume is 0.078 cu cm. When the rod is properly aligned, the holes in it constitute the "diaphragm" through which diffusion occurs. The center section was of Teflon and the rod and face plates were of Plexiglas. Four such cells were constructed and used in this study. Subsequent to this investigation, a similar cell constructed entirely of iron was fabricated and tested at higher temperatures. Several considerations led to this final design. It is desirable to minimize the volume of the cell chambers to decrease the time required for a measurement. However, the total volume of metal in the diaphragm must be small in comparison with that in the chambers. To facilitate filling and emptying it is desirable to have a diaphragm which may be closed.

Jan 1, 1970

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By John Wulff, J. H. Hollomon

THE opinion has been widely held that the corrosion of alpha brass occurs by the selective solution of zinc. As late as 1939, Fink1 and Evans2 suggested that in the initial stage of the corrosion the selective solution of zinc produces copper-rich areas, which subsequently act as cathodes that facilitate the deposition of copper. Previously Abrams3 had shown that most of the copper found on corroded brass was redeposited and not residual, although he did not consider the nature of the initiation of the corrosion process. Enough data exist to indicate that any metal surface is sufficiently heterogeneous to provide the anodes and cathodes necessary for the initiation of corrosion.4,5 Thus, for alpha brass we need postulate not an initial selective solution of zinc, but only the existence of local differences in electrochemical potential. The heterogeneity responsible for potential differences may arise from oxide and other films as well as from alloy concentration gradients. Even though selective corrosion may be possible in some alloy systems, previous data on alpha brass as well as the experimental work reported in this paper do not require this supposition. Bengough and May,6 in a discussion of Abrams' paper, first suggested the addition of small amounts of arsenic (0.03 per cent) to alpha brass to prevent the redeposition of copper (dezincification). This suggestion was later substantiated by Nixon.7 In their studies of the inhibiting influence of arsenic, Evans and Fink were led to the selective-solution hypothesis in order to explain the initial corrosion of such alloys. They believed that an arsenic film covered anode areas and prevented the formation of copper-rich spots capable of acting as cathodes for the deposition of copper. They did not consider, however, the mechanism by which the arsenical film was formed. Bengough and May,8 in another publication, suggested that the commonly found gray or black arsenical film may act to: (I) carry oxygen to the brass surface, (2) increase the discharge potential of copper on brass, (3) precipitate cuprous chloride from colloidal suspension in chloride solutions. Masing9 assumed that the film found upon arsenical brass was metallic arsenic. His measurements of hydrogen overvoltage of bulk arsenic led him to believe that the inhibition of dezincification occurs because the overvoltage of a brass surface is lowered by the arsenic film. He reasoned that this film would permit the more rapid reduction of hydrogen at the cathode, which would prevent the redeposition of copper. In a recent paper,10 we have pointed out that the film formed during the corrosion of arsenical brass and copper in stagnant solutions is essentially arsenious oxide (As203),

Jan 1, 1942

By W. T. Roberts, N. G. Turner

A study of the fatigue properties of several grades of commercially pure titanium has established that the strain-aging process is of minor importance in the development of a fatigue limit and a relatively high fatigue strength ratio. Metallographic observations and damping measurements at room temperature indicate that striations are able to spread from grain to grain only at stress levels above the fatigue limit. This suggests that the fatigue limit represents the stress above which large-scale dislocation unlocking takes place. Fatigue tests on annealed material at - 60" and - 196" c showed that under conditions when a thermally activated diffusion process would be suppressed the fatigue limit is not eliminated. Prestraining at room temperature did not have a detrimental effect on fatigue strength at room temperature but a decrease was recorded at — 60°C. This is further evidence that initial dislocation locking is a important strengthening mechanism. TITANIUM and titanium alloys have S-N curves with a definite fatigue limit, and a high ratio of fatigue limit to UTS can be attained. Other materials which show similar fatigue characteristics are mild steel and some Al-Mg alloys. The fatigue limit of these materials has been associated with their strain-aging capacity. It is well-known that commercial-purity titanium contains interstitial impurities which can give rise to a sharp yield point, and a small strain-aging effect following static strain has been demonstrated.7 This type of aging reaction is differentiated from the dynamic aging process when aging occurs during plastic deformation, and which is generally observed at elevated temperatures. In a titanium at room temperature, dislocation locking is associated with the interaction of interstitial oxygen, nitrogen, and carbon atoms with dislocations. Ehr-lich has shown that the distortion produced by introduction of these atoms into the hcp lattice has no shear stress component and hence there is no interaction between the stress field and the screw component of a dislocation. Thus the dislocations as a whole are only weakly locked. It is clear that strain-aging effects in hcp a titanium will be much less pronounced than those observed in bcc iron and steel. In recent years, the attribution of the fatigue limit solely to strain aging has been questioned. It has been pointed out that a definite fatigue limit is observed at temperatures as low as -196°C in some titanium alloys,' and strain aging is not expected to be effective at this temperature. The role of initial locking of dislocations in determining fatigue behavior has been examined in low-carbon steel by Oates and Wilson. They showed that under conditions in which the aging potential is low the factors which control the buildup of local stresses and hence affect dislocation unlocking, e.g., grain size, are important. There are indications that other metals can have a definite fatigue limit with no established strain-aging capacity, an example being magnesium12 which has the same crystal structure as a titanium. The spread of plasticity from grain to grain in hexagonal metals may be more difficult than in cubic metals because of the limited number of slip systems in the former, and this may account in part for their fatigue behavior. The present work was undertaken to elucidate the relative importance of crystal structure, strain aging, and initial dislocation locking in determining the properties of commercially pure titanium when subjected to cyclic stressing. 1) EXPERIMENTAL METHODS Three grades of commercial-purity titanium were used and a material of lower interstitial content was prepared by melting high-purity Japanese sponge titanium (referred to as H.P. Ti). The compositions and typical mechanical properties of the materials are shown in Table I. Fatigue tests were made in push-pull (zero mean stress) using an Amsler Vibraphore machine at a frequency of about 160 cps. Two types of fatigue specimen were used—one with a waisted gage length for determination of S-N curves and the other with a parallel gage length for metallographic studies and damping measurements. After careful machining and mechanical polishing, all specimens were electropolished prior to fatigue testing. The electrolyte consisted of 10 parts methyl alcohol, 6 parts 2-butoxyethanol, and 1 part perchloric acid (SG 1.54) and it was maintained at a temperature of -10" to -20°C during polishing. Tests at room temperature were normally carried out with the specimen immersed in a silicone oil bath which could be heated for elevated-temperature tests.

Jan 1, 1969

By F. J. Plecity, J. T. Michalak, W. C. Leslie

Isothermal recrystallization and grain growth in zone- and vacuum-melted irons and Fe-Mn alloys, up to 0.60 pct Mn, were studied in the range 480° to 650° C, after 60 pct cold reduction. In initial stages, rate of grain growth and rate of recrystallization of iron decrease with time. The recrystallization is typical of a growth-controlled process, and rate of growth is determined by the extent of recovery. Mn decreases rates of growth and of recrystallizatzon. The recrystallization process changes at about 0.30 pct Mn and nucleation may become time-depetzdet~t. In recent years, considerable effort has been expended in determining the effects of solute elements on recrystallization and boundary migration in fcc metals. The results have indicated that the effects produced by single solute additions are dependent upon both the element added and its concentration.'-' In contrast, there have been very few attempts to determine the characteristics of recrystallization and boundary migration in high-purity bcc metals, especially after heavy deformation, and the effects thereon of single solute elements.9-11 This study was undertaken to determine the recrystallization characteristics of various "high-purity" irons and the effects of manganese additions at two levels of base purity. It was hoped that the information obtained would improve our understanding of the recrystallization of pure metals and aid in formulating a theory for the effect of solute elements. The interest was not entirely academic, for the annealing of low-carbon steels, which is of very great commercial importance, is but poorly understood. MATERIALS The compositions of the irons and iron-manganese alloys used are listed in Table I. The zone-melted iron and Fe-Mn alloys were made by Battelle Memorial Institute. Iron S-1 was arc-melted in a water-cooled steel mold in an argon atmosphere. The ingot was forged into a bar, then given two horizontal zone-refining passes in an alumina boat. Iron V-4 was treated in a similar manner, but was not zone-refined. The iron for the zone-melted Fe-Mn alloys was induction melted in vacuum in MgO crucibles and cast into alumina molds. The ingots were forged into bars, machined to shape, and a groove milled down one side of each. The best available electrolytic Mn was placed in the grooves, and the bars were zone melted. The vacuum-melted Fe-Mn alloys were induction melted in this Laboratory in MgO crucibles and poured into cast-iron molds. Iron V-5 was purchased from National Research Corp. in the form of a small vacuum-cast ingot. The low-carbon steel was made by induction melting in air at the U.S. Steel Corp. Applied Research Laboratory. The history of the materials prior to the final cold reduction differed; these details are given in the Appendix. The penultimate grain size of the principal materials was kept in the range ASTM 2 to 4, except for the low-carbon steel. PROCEDURES The cold work prior to the final recrystallization anneal was kept constant at 60 pct. It is known that rolling procedure can influence the kinetics of recrystallization of ironI2; therefore, all specimens were rolled in one direction only, between clean,

Jan 1, 1962

By H. M. Faust

THERE are a number of different types of power plants. Some use coal to generate steam, others use oil or gas either in the form of steam or internal combustion equipment, while still others avail themselves of water power as a source of energy. A general comparison of the relative power production with different sources of energy in the United States, for several different years is set up in Table 1. This table shows that coal was used to generate 85.6 per cent of the total heat power requirements of 1909, and only 59.2 per cent of the 1930 requirements. The increasing proportion of modern heat energy generated by the use of fuel other than coal is apparent. If coal is to maintain its importance as a source of heat energy, the necessity for its improved perform-ance, in which preparation plays an -important part, cannot be stressed too strongly.

Jan 1, 1933

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,' the gold film marker of Kofstad and ~jijllesdal,' and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.' reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By Å. Sterten, R. Tunold, J. Brun, K. Dalatun

c axis compression behavior of beryllium single crystals at three purity levels under hydrostatic pressures up to 27 kbars was determined. Extensive non-basal slip, observed by two-surface trace analysis and transmission electron microscopy, occurred under a hydrostatic pressure of about 12 kbars (175 ksi) for the high-purity (twelve-zone pass) material and at about 19 kbar (275 ksi) for the lower-purity (zone-leveled) material. Prismatic loops with a (c + a) Burgers vector were observed in association with second-phase parti- A principal factor limiting the use of beryllium is its brittle behavior when tested at the usual strain rates (E = 10-4 sec- 1) at temperatures below about 200°C and under impact conditions at temperatures in excess of 200°C. It has been proposed' that the brittle-ness of beryllium is associated with the lack of a sufficient number of independent slip modes and the absence of a slip mode with a Burgers vector out of the basal plane [presumably (c + a) pyramidal slip mode] and to the ease with which beryllium cleaves on the basal and second-order prism planes. The absence of pyramidal slip has been attributed to a high Peierls-Nabarro stress associated with the motion of dislocations with a (c + a) vector and the ease with which cleavage occurs on the basal and second-order prism planes. The experimental evidence in support of the proposed explanation for the brittleness of beryllium is far from complete; for example, that the ductile-to-brittle transition in polycrystalline beryllium is associated with the operation of profuse (C + a) slip has not been unequivocally established. The occurrence of (c + a) slip ({1122}(1123)) has been experimentally established2-5 under conditions where basal and prism cleavage are restricted in a c axis compression test. In these investigations (C +a) slip was found in high-purity beryllium single crystals tested in c axis compression* at 200°C and in Be-4.4 pct Cu and Be-5.2 pct cles in the lower-purity materials tested. The loops were related to surface "extrusions" observed on many of these same specimens. Nonbasal dislocations operating on (1122) planes with a (c + a) Burgers vector were observed. The presence of c and a dislocations together with (c + a) dislocations suggests that the (c + a) dislocations dissociate presumably on unloading or after failure of the test crystals to c and a dislocations. terial, (c + a) slip has only been observed near the the fracture4 surface in room-temperature c axis compression tests. Fracture in these tests occurs without measurable plastic flow, as determined with a strain sensitivity of 10"6. Since it has been shown for many metals that the application of hydrostatic pressure suppresses fracture,?-' it was felt that studying the behavior of unalloyed beryllium single crystals stressed in c axis compression under a hydrostatic pressure would reveal whether (c + a) can occur if fracture was prevented, and that it might elucidate the role of (c + a) slip in the ductile to brittle transition. Evidence that (C + a) slip is associated with increased ductility in a high-pressure environment has been found in stress-strain tests on poly crystalline beryllium.10 The present paper describes a study on the influence of a hydrostatic pressure environment on the occurrence of (c + a) slip in beryllium single crystals. Material of two purity levels was tested in c axis compression over the pressure range ambient to about 27.5 kbars.* 1) MATERIAL PREPARATION AND CHARACTERIZATION Two lots of low-purity single-crystal beryllium were used. The first lot was "ingot secondary refined grade" and designated lot A. The second lot (lot B) was produced by a two floating zone pass zone-leveling operation in an argon-filled sealed quartz apparatus on a 1-in.-diam by 12-in.-long bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. The high-purity material (lot C) was made by traversing twelve floating zone passes through a similar bar of Pechiney secondary refined-grade vacuum-cast and hot-extruded material. In a series of spark cutting and lapping procedures,11 single-. crystal specimens some 0.12 in. sq by 0.30 in. high were made with the sides Parallel to the first- and second-order prism planes and the basal plane within 3' of arc of the top and bottom surfaces of the specimen. Such an accurate orientation is necessary because of the large difference in resolved shear stress

Jan 1, 1970

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

By John Mills

THREE case histories from professions other than engineering will serve to introduce ideas basic to this discussion. Case (1) Date, about 1900. A young man, B. D. from a three-year graduate course in a prominent divinity school, was for two years a successful pastor of a small church; then friction over theological matters arose with a fundamentalist deacon of the "Bible belt" type. He resigned, returned to his university for a four-year medical course, interned for two more, and thereafter was successful and apparently happy as a physician. We may assume that he was converted in early adolescence and vowed himself to service as a minister. Acceptance of his announced career by parents, friends, and teachers plus his own determination confirmed his choice until illiberal criticism threatened his usefulness and he awoke to the fact that his inner needs were not along the direction in which inertia and his conscience had constrained him.

Jan 1, 1947

By B. C. Allen

Liquid surface tensions of copper and 18 Group IV-A to VIII transition metals (Ti, Zr, Hf, V, Cb, Ta, Mo, W, Re, Ru, Rh, Pd, Os, Ir, Pt, Fe, Ni. Co) have been measured by the static pendant-drop and dynamic drop-weight methods on the same rod sample. The drops were formed by electron-bombardment heating in high vacuum. Application of necessary corrections enabled determination of surface tensions to k2 pct and agreement between methods to * 1 to 4 pct for all the metals studied. Evidence is presented that the liquid surface was well screened by metal vapor, suggesting negligible adsorption of gaseous impurities and that the surface tensions measured are characteristic of the metals involved. Correlations between liquid surface tension and melting point, molar volume, heat of vaporization, and atomic number are presented and discussed. Temperature coefficients of surface tension were calculated using Eötvös' law. SURFACE tension and interface energies of metals are the result of incomplete atomic coordination resulting in a force perpendicular to the boundary, tending to minimize its area. These energies are important in many phases of metallurgy, including microstructure, sintering, joining, electronic emission, and lubrication, which in turn affect many physical and mechanical properties of metals. Liquid surface tension refers to the interface between the liquid and its own vapor or nonreactive atmosphere, and is considered a physical property of the liquid. Since equilibrium shapes can be readily obtained with liquids, the units of surface tension (force per length) and interface energy (energy per area) are interchangeable. Thermo-dynamically, the surface tension ?LV is given by the change in free energy F with surface area A at constant pressure P, temperature T, and composition N: for commercially important refractory metals, vanadium, columbium, tantalum,13,14 molybdenum,14 and tungsten,l5 and none for the rare platinum-group metals and rhenium. Measuring the surface tensions of transition metals is difficult because of their high reactivity and melting points. Of the many techniques available,16-18 the pendant-drop 19-21 and drop-weight methods17,22 are considered superior because they can be modified to eliminate persistent sources of contamination such as supports and capillaries necessary in the popular sessile drop, capillary rise, and maximum-bubble-pressure techniques. The necessary modification is to melt a drop on the tip of a vertical rod, which provides support through a solid of the same composition.13,15 The object of the work was to study the surface-tension behavior of copper and transition metals, having reasonably low vapor pressures. Liquid surface tension of each pure metal was systematically determined by using a combination of the static pendant-drop and dynamic drop-weight methods on the same rod. Liquid drops were formed by electron-bombardment heating in high vacuum. EXPERIMENTAL WORK As indicated in Table I, the metals studied were high purity and generally were obtained in rod form. The exceptions were titanium and zirconium, which were machined from crystal bars, and molybdenum (tot 11, osmium, and ruthenium, which were sintered and arc cast into rods. All the metals were ground or swaged to desired sizes between 1- and 7-mm diam, and centerless ground round and smooth to a finish better than 50 µ in., rms. Each rod was thoroughly cleaned with steel wool, degreased, acid etched, and dried. In a typical run, the rod was vertically clamped in a modified floating-zone electron-bombardment furnace designed after Calverley23 and Carlson.24 The specimen was outgassed and maintained positive at several kilovolts in a dynamic vacuum of 10-5 to 10-7 mm. The bottom end was enclosed by a tantalum pillbox and heated by electrons emitted from a hot concentric tungsten filament mounted on a movable bracket. The bombardment power was slowly raised until melting was observed. Power requirements ranged from 30 w for copper to 1300 w for 4-mm tungsten. The stabilized and out-gassed drop of near-maximum size was photographed at 4. 1X on panchromatic film at desired time inter-

Jan 1, 1963

By Arthur Phillips

THE normal method of preparing metallic alloys for commercial use involves the preparation of a melt containing the given components in the chosen proportions and allowing the homogeneous liquid mass to solidify in a mold of the desired form. The solidification is frequently accompanied by a segregation of the alloying elements in different parts of the casting. When the segregation is occasioned primarily by marked differences in density of the solid and liquid phases, it is termed "gravity" segregation. When the segregation conforms to a. selective freezing in harmony with the teachings of the equilibrium diagram of the alloy system-i.e., the lower melting phases are concentrated in the regions of the casting last to freeze-it is often referred to as " normal" segrega-tion. However, in many cases the lower-melting part of the system is concentrated in the parts of the casting first to freeze and the result in this case is termed "inverse" segregation. To complete the. terminology of the subject, normal segregation in a single phase is usually called "coring" and the word will be used in that sense in this paper. Inverse segregation, particularly when the liquid phase is exuded or sweated out on the surface of the casting, is sometimes called "location." Unfortunately, some ambiguity has arisen from the use of this term and it is perhaps advisable to confine its use to the dictionary definition; namely, "The separation of two phases by heat sufficient to melt one but not the other." The gravity and normal types of segregation are both well understood and to some extent are controllable by taking advantage of the most favorable cooling rate for a given casting condition. Inverse segregation has received considerable attention from several investigators- but none of the theories offered seem to account in a convincing way for the many examples of this type. The observations made in the present work on segregation in single crystals, and in some other castings, tend to support one theory of the mechanism of inverse segregation and definitely to

Jan 1, 1937

By F. E. Bachman

Although it has been apparent to me for a long time that too great weight was currently given to the silicon-contents of foundry-iron, and that the theory of the control by silicon of the carbon-contents of cast-iron is unsound, or that, at best, the influence of silicon is too small to be of much practical value as a guide in foundry-work, it never seemed to me desirable to enter the lists against either the " silicon-fad " or the theory, for the reason that I had neither the time nor the facilities to prove my position, nor any better theory to offer. But since Mr. Summers has taken the step, it seems but right that I should give such facts as are at hand in support of his contention. At the same time I do not think these are enough to prove the case if the contrary proposition were not itself, as it seems to me, based on insufficient evidence. Both Keep's and Turner's conclusions seem to be drawn from irons carrying less than the normal amount of carbon; Turner's " base " being, moreover, a steel rather than a pig-iron, and both the white base and the ferro-silicon of Keep being so low in carbon that compounds of them would not give a material approaching the carbon-contents of a normal casting, and having, therefore, little value as showing the effects of silicon on foundry-irons, even if his samples were treated under the same conditions as those to which pig-metal is subjected in making castings.

Jan 1, 1899

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By M. H. Waxman, M. Gondouin, H. J. Hill

Streaming-potential experiments were conducted within the Muddy- and Dakota-sandstone interval of a Denver basin well. Analysis of the data shows that, for this case, streaming potentials opposite sands were higher than those opposite shales when the mud was fresh. Streaming potentials opposite shales, however, were of sufficient magniiIlde to be important in SP interpretation. They were linearly dependent upon pressure differential, and they increased with mud filtrate resistivity. The magnitude of streaming potentials opposite sands was influenced by the characteristics of the original mud cake formed at the time of drilling. Use of mud samples taken at the time of logging may not always be satisfactory for determining streaming-potential corrections. Both the streaming and electrochemical potentials were found to be affected by the previous history of the borehole system. Following a change in mud characteristics, several days were required for SP stabilization. This was, in part, due to the mud cake acting as an imperfect shale membrane. INTRODUCTION Laboratory investigations by Wyllie,1 Salisch,2 Moore," Sen Gupta and Bannerjee,0 and Hill and Anderson' have shown that streaming potentials developed across mud cakes deposited on permeable filter beds are of sufficient magnitude to be critically important in SP interpretation. Streaming potentials across shales have been reported by Schenck,' Gondouin and Scala; and Hill and Anderson." The magnitude of the shale streaming potentials obtained by Schenck and by Gondouin et a1 led these authors to conclude that in many cases the shale streaming potential would approximately equal the mud-cake streaming potential. Hill and Anderson, however, obtained somewhat lower magnitudes of shale streaming potential. The field experiment described in the present paper was a cooperative project carried out by the respective operations and research departments of Schlumberger Well Surveying Corp., Shell Development Co. and Shell Oil Co. The primary objective of the experiment was to determine in the borehole the streaming-potential behavior of both shales and mud cakes under conditions approaching, as nearly as possible, those normally encountered in logging practice. METHODS AND EQUIPMENT WELL A Muddy- and Dakota-sandstone vie11 in the Denver basin was chosen for the experiment. Both sandstones were water-bearing and, since reservoir pressures in these sandstones are abnormally low (gradient of approximately 0.25 psi/ft), it was expected that studies of streaming potential could be conducted from low-pressure differentials (approximately 200 psi) to about 27000 psi by bailing mud from the hole, filling up and then applying wellhead pressure. The selected well encountered the Muddy sand-