Search Documents

By Graham Bright

THE rapid increase in reliability, the low cost f operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the' motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made.

Jan 9, 1921

By Alfred H. Bell, Virginia Kline

In 1944, Illinois produced 77,413,000 bbl. of oil, or 4.6 per cent of the total for the United States, and continued to rank sixth in the nation in oil production. This represents a decrease of 6 per cent from 1943, when- the total Illinois production was 82,256,000 bbl. This decrease was much less than the 23 per cent decrease in 1943 from production of the previous year. The principal factor in arresting the production declinc, which had been going on since 1941, seems to be the increased drilling that followed the relaxing of the Federal Government's rules in regard to well spacing. The daily average production for 1944 was approximately 212,000 bbl. Daily averages by months were as follows: Jan......... 219,000 July........ 206,000 Feb......... 220,000 Aug......... 211,000 Mar........ 216,000 Sept......... 209,000 Apr......... 211,000 Oct......... 210,000 May........ 213,000 Nov........ 209,000 June........ 209,000 Dec......... 205,000 During the year, 1991 wells were drilled for oil and gas in Illinois as compared with 1791 in 1943, an increase of II per cent. Of the 1991 wells, 430 are classified as "wildcat" as compared with 461 in 1943. Twenty-eight new pools (Table 2 A) were discovered in 1944 as compared with 29 in 1943. Changes in federal drilling regulations, permitting closer spacing of wells, resulted in a drilling program that emphasized development of proved acreage rather than wildcatting. Data on production and drilling by fields are given in Table I; data on annual production and drilling for Illinois, in Table 3. Discoveries Twenty-eight new fields (Table 2 A), 42 extensions (Table 2 B), and 39 additional producing zones in existing fields (Table 2 C) were discovered in 16 counties in Illinois during 1944. Of the 28 new fields, one was abandoned during the year, 14 were one-well fields, eight others had not more than 6 wells, one had 8, one had 9, one had 11, one had 15, and the largest new field, Roaches North, had 28 producing wells at the end of the year. In all, 109 wells were producing in these new fields on Jan. 2, 1945, as compared with 111 wells producing from 29 new fields at the end of 1943. . The average initial production of the discovery wells of the 28 new fields was 129 bbl. of oil and II bbl. of water, a notable decline from the average initial production of 194 bbl, of oil and 15 bbl. of salt water for the 1943 discovery wells. In fields discovered since 1936, the total number of oil wells producing at the end of 1944 was 12,335. Productive Acreage The area of proved production in the new fields (discovered since 1936) increased from 144,335 acres at the end of 1943 to 173,485 acres at the end of 1944 (Table I), an increase of 29,150 acres. Of this increased area, 1720 acres are in fields discovered during 1944 and 27,430 acres are in extensions of fields discovered earlier.

Jan 1, 1945

By Harold Roast

THE object of this investigation was to compare the arsenical antimony-lead alloy with some of the regular bearing-metal alloys. With this end in view, the following tests were made: 1. Chemical analyses to show the composition. 2. Thermal analyses. 3. Macroscopic examination of fractures. 4. Microscopic examination. 5. Tensile tests. 6. Crushing tests. 7. Scleroscope tests. 8. Brinell tests, at temperatures from 80° to 400° F. Tests 3 to 8 were conducted on both sand-cast and chill-cast specimens. For the purposes of this paper the alloys have been numbered from 1 to 6; their composition is as follows: LEAD, ANTIMONY, TIN, COPPER, ARSENIC, NUMBER PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. 1 82.64 12.95 4.40 0.01 none 2 27.54 9.94 59.87 2.65 none 3 77.65 20.75 none 0.13 1.47 4 82.95 16.85 none 0.20 none 5 83.78 15.35 none 0.05 0.82 6 0.15 7.87 84.13 7.85 none The analysis, in the case of the antimony, was made by solution in sulfuric acid and titrated with permanganate. For tin, the ferric-chloride method was used; for copper, the alkaline separations, and the thiocyanate methods; for arsenic, volatilization of arsenic and titration with iodine. The lead, with the exception of alloy 6, was taken by difference.

Jan 2, 1922

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

By Strathmore R. B. Cooke, Iwao Iwasaki, C. S. Chang

The effects of aeration on an aqueous suspension of pyrrhotite were studied and their results correlated with flotation tests using xanthates as collectors. The effects of copper activation and of pH variation were determined and possible mechanisms postulated. PYRRHOTITE has long been considered a gangue mineral to be eliminated as tailing in the treatment of various sulphide ores. However, in recent years the world-wide lack of sulphur resources has called attention to this mineral as a potential source of both sulphur and iron. Its importance as an economic mineral, however, has not been particularly emphasized. For this reason very little is known about its response to flotation, except that it can be depressed easily in alkaline circuit, by long aeration,1,2 addition of oxidizing agents,3 or by starch.' The object of this work was to study the floatabil-ity of pyrrhotite. This includes the effect of oxidation by aeration, of copper activation, and of change in pH. Preparation of the Pyrrhotite Sample: It was desirable that the highest grade of pyrrhotite obtainable be used for this experiment, since the presence of other minerals could affect the surface properties.5 However, no pyrrhotite was available as crystals, and massive deposits of hydrothermal origin commonly contain considerable amounts of chalcopyrite. Pyrrhotite concentrate was, therefore, prepared from a sulphide deposit occurring near Aitkin, Minn. The deposit is of pyrometamorphic nature consistirlg mainly of pyrrhotite and pyrite with graphite, silicates, and carbonates as gangue. The ore, already crushed through 3 mesh when received, was screened at 65 mesh and the undersize discarded. The oversize was crushed through rolls, and then stage-ground dry in an Abbe porcelain mill, the —65 mesh portion being screened out after every 15 min of grinding until all the material passed through this size. The ground product was then concentrated with a drum-type dry magnetic separator. The rougher concentrate was cleaned twice and then demagnetized. The final product was split in a Jones splitter and stored in air-tight bottles. Microscopic examination of the concentrate showed that it was relatively clean and free of pyrite, locked particles, and gangue. By means of the krypton gas adsorption method," the specific surface was determined to be 3000 cm2 per g. The chemical and screen analyses of the final concentrate are given in Tables I and II respectively. It is a well-recognized fact that the oxidation of some sulphide ores during stockpiling, grinding, and conditioning affects their flotation behavior. The problem of oxidation may become serious in the case of pyrrhotite, since this is known to be more easily oxidized than many other sulphides. To ascertain the extent of oxidation, an experiment was carried out by aerating an aqueous suspension of pyrrhotite with air, oxygen, and nitrogen as follows. A 300-g sample of pyrrhotite in 2700 ml of water was agitated and simultaneously aerated in a Fager-gren-type laboratory flotation machine. A Precision wet test meter was connected to the air inlet valve, the flow rate of the gas being kept constant at 0.3 cu ft per min throughout the experiment. Samples of approximately 30 ml each were taken from the cell at 0, 4, 10, 20, 35, 60, and 90 min. After the pH was taken, each sample was filtered and the filtrate was analyzed for total iron and sulphur. The iron was determined colorimetrically by the thioglycolate method using a green filter.' The filtrate was oxidized with bromine to convert all of the soluble sulphur compounds into sulphate and this was determined with a Parr turbidimeter." When aeration tests were made in alkaline circuit, calcium hydroxide or sodium hydroxide was added at regular intervals to maintain a constant pH. A similar procedure was followed in an experiment to determine the abstraction of copper. ion by pyrrhotite. In this case various quantities of cupric chloride were added. The filtrate from each sample taken was analyzed for copper, total iron, and sulphur. The carbamate method with a green filter was used for the copper analysis,' since this method could tolerate a considerable amount of iron in the solution. A pneumatic cell, made from a 350-ml fritted glass Buechner funnel, was used for this experiment. The detail of the assemblage has been described elsewhere." In the present work a stainless steel baffle was inserted in the cell. This baffle overcame the tendency for the coarse pyrrhotite particles to be swirled around the wall of the cell and thus fail to collect in the froth. A 50-g sample of pyrrhotite was added to the cell which contained 260 ml of water. When pretreat-ment of the sample was desired, reagents, such as activator and pH regulator, were then added and the pulp was conditioned for a specified conditioning time. Prior to the addition of the collector approximately 15 ml of the solution were removed for pH measurement and for iron and sulphur analyses. Copper when used as activator was also determined. Collector and frother were then added and the pulp was conditioned for an additional 2 min. Air was admitted to the cell and the froth removed. The separation required from 4 to 6 min, depending on the characteristics of the froth. The float and non-float products were filtered, dried, weighed, and assayed for iron.

Jan 1, 1955

By C. F. Frey, P. J. Ahern, J. F. Wallace

THE high affinity of molten titanium for oxygen and nitrogen has resulted in considerable difficulty in developing a satisfactory melting procedure. It has been found necessary to perform melting operations either in a vacuum or inert atmos-phere, and failure to obtain a satisfactory crucible material has necessitated the use of special melting techniques. These techniques have included cold-mold arc-melting utilizing both consumable and nonconsumable electrodes, skull-melting, drip-melting, and levitation melting.' It has been recognized generally that the melting of both titanium sponge and titanium scrap would be expedited by the use of induction-melting procedures but the lack of a crucible capable of containing molten titanium without objectionable contamination thus far has prevented the use of induction-melting procedures. An extensive investigation: which included the common refractory materials was not successful in developing a satisfactory crucible for induction-melting. Some success in induction-melting has been attained with the use of a graphite crucible material, but in all instances sufficient carbon contamination was encountered to cause an appreciable reduction in the optimum mechanical properties of the titanium or titanium alloys. These investigations"" report an increase in the carbon content from approximately 0.3 to 1.0 pct. A serious reduction in the tensile and forming properties has been observed as a result of this carbon contamination. The development of a satisfactory induction-melting procedure for titanium without undue contamination undoubtedly would have considerable economic significance. Such a process would be particularly useful in melting the large quantities of low-cost scrap now available that can only be reprocessed at considerable expense and difficulty by the more elaborate techniques referred to previously. In addition, the process could provide a satisfactory method of melting and alloying of bri-quetted sponge for forging ingots.

Jan 1, 1959

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated mineral-spyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying 1 per cent is considered good grade; 0.7 to o.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent WO3 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 6o to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By H. E. Nold

THIS paper is an effort to explain in a simple manner the fundamental principles involved in examining a clay deposit for both quantity and quality and in operating a clay mine, either open-pit or underground, SO that the best quality of finished material can be made from the raw material available. The writer is aware that what is recommended in this paper is everyday practice in many refractories plants and in some other heavy-clay products plants, but observations made while visiting practically every clay mine in Ohio have convinced him that the practices herein discussed are not as widely used as their importance warrants. It is true that the problem of mining for quality is more acute in refractories plants than in most heavy-clay products plants, yet some of the latter are finding it profitable to pay more than ordinary attention to the selection and blending of their raw materials. It is hoped that this short paper may prove helpful to some who are now finding it difficult to produce a uniform product of as high quality as their clay deposit seems to warrant. The coordination of the work of the clay mine or pit with the manufacturing plant, to the end that the best product possible be made from the raw material available, presupposes a rather intimate knowledge of the clay deposit. The knowledge must include not only information of the amount of clay available but also rather detailed information about both vertical and horizontal variations in quality of the clay. This information should cover three things: quality, quantity, and location. Sampling Undeveloped Deposits In the case of an undeveloped deposit with a shallow overburden, pitting may be the cheapest way of testing. For thick deposits or deposits with rather heavy overburden, the diamond drill, using a double core barrel, offers the best means of testing. When using the diamond drill in clay testing, it is doubtful whether it pays to take less than 2-in. cores; it is difficult to get complete cores with smaller drills, and the quantity of material obtained with smaller cores is not sufficient for the necessary tests.

Jan 1, 1929

By S. R. Titley

The recent emphasis placed upon the use of molybdenum as a geochemical indicator has stimulated considerable inquiry into the behavior of molybdenum in the zone of oxidation. This paper represents a summary of recent and continuing experimental work and calculations in an investigation of a portion of the system Mo-Fe-S-H20 and treats the stability of various iron and molybdenum compounds with respect to oxidation potential and pH. Using experimentally determined free energy values for ferrimolybdite, diagrams of the stability fields of this mineral have been calculated with respect to ilsemannite (?), molybdenite, pyrite and limonite. This theoretical approach is the one utilized by Garrels3'4 in studies of the relationships of various minerals in the zone of oxidation. Use of this approach is particularly suited to the study of geochemistry in the zone of supergene processes because of the low temperatures, low pressures and other relatively easily determined and duplicated factors that exist in the near surface environment. Such a study of molybdenum, however, is complicated by several factors. One of these is the fact that the strong amphoteric behavior of molybdenum makes possible a wide variety of substances and complexes whose exact chemical natures are unknown. The second factor is the dearth of thermodynamic data for many of the simplest of the possible compounds and ions important to the study. For the purpose of this study, the problem of complexes has been approached through considering only the simpler possibilities realizing that the complexes and systems so treated may be gross oversimplifications. All the complexes considered, however, have been suggested in the chemical 2,7,9,12 or geologi-cal literature. EXPERIMENTAL WORK Studies of the behavior of molybdenum ions and ferrimolybdite have been carried out in aqueous sys- tems, and reactions have been followed by simultaneous measurement and recording of pH and oxidation potential. A major problem involved in this study was the long periods of time necessary for equilibrium to be established in some of the systems considered; in a few instances, these periods exceeded four weeks, that is, four weeks during which measured conditions changed continuously. Another problem, in some instances, was the indeterminate nature of the reactions that have taken place. Because of the tendency of molybdenum to complex, reactions which take place under some of the more extreme imposed conditions of oxidation and acidity or alkalinity are unknown. However, useful data for the present work were obtained from studies of the molybdate ion and ferrimolybdite between pH 2 and 8 and under only moderately oxidizing to nonoxidizing conditions. Instruments used in the experiments were a Hewlitt-Packard Model 412A VTVM, a modified Beckman Zeromatic pH Meter and two Varian model 11 recorders. pH was measured between glass and calomel electrodes and Eh was measured between calomel and platinum electrodes. Conditions of pH were varied with 1N H2SO4 and 1N NH4OH and 1N NaOH. Eh was varied with gaseous nitrogen, oxygen or aqueous H202. Ambient temperature was essentially uniform at 24ºC and was increased in the reaction vessel by the positioning of a magnetic stirrer whose temperature was sufficient to bring the temperature to 2S°C in the reaction. The temperatures of reaction did not vary more than 1/2ºfrom 25°C. Two reactions were investigated, the ferrimolybdite-limonite-water reaction and the reduction of molybdate ion. Studies of both reactions yielded useful data that were used in preparation of the Eh-pH diagrams. The traces of the reactions are shown on Fig. 1. Ferrimolybdite-Limonite- Water: Studies of this reaction involved analysis of the solution of ferrimolybdite and simultaneous formation of ferric hydroxide. The data are summarized on Fig. 1. In this reaction, equilibrium was attained at various pH's when coexistence of the two solid phases (ferrimolybdite and ferric hydroxide) was attained. At the proper pH, controlled by the amount of ferrimolybdite and thus the dissolved content of molybdate species, both phases were observed and reaction times to complete the transition were on the order of weeks. The reac-

Jan 1, 1963

The Lead-Line Update held in conjunction with the 1977 SME-AIME Fall Meeting in St. Louis provided sessions on mining, mineral processing, extractive metallurgy, and economies to brief the record on the industry's activities and developments since the 1970 World Symposium on Lead and Line convened, also in St. Louis. Changes in the industry since 1970 have not been profound, notes the program committee, consisting of D. O. Rausch, F. M. Stephens, and B.C. Mariacher, cochairmen; and H. L. Clifford, S. C. Fall), and M. Snedeker. However, various environmental and conservation factors have had a direct impact on process consideration and operating practice; the result has been new mines, improved technology, and changing market opportunities. The general consensus of the participants is that the future for the Lead-zinc industry looks promising as new applications are found and new products resulting from intensive research reach the marketplace. The highlights of the HS technical papers presented at the 1977 session follows.

Jan 11, 1977

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriston, Durham, England. 1935. GUILLAUME DANIEL DELPRAT Melbourne, Vic., Aust. 1920. HENRY STURGIS DRINKER Merion Station, Pa. 1933. KARL EIKERS NEW YORK, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYS HAMMOND New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Paris, France. 1931. WALDEMAR LINDGREN Cambridge, Mass. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1935. ROBERT PEELE New York, N. Y. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada 1933. ALBERT SAUVER Cambridge, Mass.

Jan 1, 1936

By A. Singh, W. M. Fleming, J. J. Santana, A. E. Torma

The present study investigated the extraction of uranium from a low-grade ore by sulfuric acid and the removal of radium from the leach residues by brine solutions. The optimum leaching conditions were found to be 1.5 mole [£]-1 H2SO4, 6.Og[9]-1NaClO3, 75°C,50% pulp density and 750 rpm with respect to the rate of uranium extraction. The maximum theoretical attainable rate of uranium extraction was determined to be V = 1.09 x 10 -2 mole [¢]-1h-1 with respect to pulp density. The order of reaction was found to be zero regarding the effect of sodium chlorate concentrations. The apparent activation energy of uranium extraction was calculated from the Arrhenius plot to be [A]E a - 2.36 kcal mole-1 (9.87 kJ mole-1). Based on a statistical design, an empirical equation has been developed describing the rate of uranium extraction with the leaching parameters. This equation can be used to generate data which may be useful for scaling up the process to pilot plant level. The most efficient brine solution for the extraction of radium - 226 from the leach residue was found to contain one mole[f] -1 CaCl2 and 0.01 mole [2] -1 HC1. The two step leaching with this solution resulted 87% removal of radium from the leach residue. On the basis of this study, a flow-sheet has been proposed for the extraction of uranium and radionuclides from the ore and leach residue to yield almost innocuous tailings.

Jan 1, 1982

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By R. S. Dean

The commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in Mining and Metallurgy for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for " the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. Practice at BouldeR City The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: 1. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

A B Cummins President James C Gray, President-Elect J W Woomer, Past President C E Lawall, Eastern Regional Vice-President Donald W Scott, Central Regional Vice-President H C Weed, Western Regional Vice-President Nathaniel Arbiter, Treasurer John Cameron Fox, Secretary AIME 29 W 39 St New York 18, N Y

Jan 1, 1960

By C. S. Samis, J. C. Mitchell

Sodion activity data have been obtained for the Na-A1 system for sodium concentrations in aluminum between NN, = 25 . 10-and 300 x 10'. This concentration intert-a2 encompasses those sodium concentrations nor1)zally encountered in aluminum reduction cell operation. The sodium activity data were measured by a two-phase equilibration of sodium between a lead and an aluminam rich phase. The Na-Pb system was emplojed as a reference for the determination of the actiz7itj 0.f sodium. The activity of sodiin in aluminuwz exhibits large positi2.e deviations frorn ideality and a strong dependence, on concentration below NN, = 100 x 1K6. The inteated data indicate that the activity of aluminium is equal to its mole fraction over the range of miscibility of the Na-A1 sgstem. The data on the Na-A1 binary have been combined with experimental data on the cryolite-A1 system at 1025°C to obtain the activities of Na F and AlF, in liquid cryolite oz2er the cornposition 1-ange encountered in aluminum cell operation. The results are in agreement with activities calculated from the NaF-AlF, phase diagram. ALUMINUM is produced commercially by the electrolytic reduction of aluminum oxide dissolved in molten cryolite. There is considerable controversy over the actual mechanism of the discharge processes, but sodium potentials in the systems appear to play an important role in the reduction mechanism. The metal-salt reaction involving NaF and aluminum to produce A1F3 and sodium is responsible for the presence of sodium in the aluminum metal phase. Additional sodium may be produced from the simultaneous deposition of sodium and aluminum at the cathode as a result of a cathodic overvoltage. runert' has suggested that sodium gas at atmospheric pressure would be the result of reaction between cryolite and aluminum at 1000°C. Subsequent investigations have shown that production of sodium at atmospheric pressure does not occur. These later investigations can be conveniently separated into two categories. The first involves sodium, aluminum, and cryolite, in which the sodium activity was measured. The second includes a lead phase for sodium activity measurement. Jander and errmann,' studied the reaction: at 1090°C in alumina crucibles under an atmosphere of dry, oxygen-free nitrogen. The equilibrium constant for the reaction was expressed in terms of concentration. Their results in Fig. 1 show an increase in sodium content of the aluminum with increasing NaF/A1F3 weight ratio. Pearson and waddington3 performed similar experiments at 1000°C. Their results are included in Fig. 1. Dewing and ollinshead have measured the sodium content of aluminum as a function of the NF/AF, ratio at 1025"C, Fig. 1, and ewin' measured the sodium content of the aluminum in a system involving the solid reactants NaF, cryolite, and liquid aluminum. This reaction is different from those discussed above. Two solid phases, NaF and Na3A1F6, and a liquid aluminum phase were present. The sodium concentration in the aluminum was determined by the temperature. Dewing's measurements covered the temperature range 679" to 896°C. Omo, Matsushima, and 1t02" investigated the equilibrium 6NaF ential thermal analysis. Stokes and Frank6 determined sodium activities by

Jan 1, 1970

By John Chipman, Carl F. Floe

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Carl F. Floe, John Chipman

The system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100" to 1500ºC., and pressures from about 20 mm. of mercury to somewhat above atmospheric. Review of Previous Work The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as O2, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: 2M+G2=2MG K=(MG)2 /M2 X PG2 [I] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: MG = K1 vPG2 [2 Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: 6Cu + SO2 = Cu2S + 2Cu2O [3] K= Cu2S X (Cu2O)2 i - (Cu)6(Pso2) [4] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: K1 =V3SO2 /Pso2 or

Jan 1, 1941

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922

By Enrique Touceda

For a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At the outbreak of the war the firm decided to specialize in the manufacture of propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods of manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual blade mold formed, the pattern is then rotated on the spindle to the position for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this pratctice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface of each blade must be chipped to the templet and through this procedure chipped to such accuracy as will be required for a static balance. Inasmuch as the work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin of the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days of foundry work and about the same length of time for the machining. Through the use of the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity with any particular propeller-wheel design.

Jan 1, 1922