Search Documents

By J. L. Wyatt

THE smelting of ilmenite to produce a slag rich in titanium, with pig-iron as a byproduct, introduces new concepts in electric smelting metallurgy. Titanium slags are characterized by low electrical resistance, thereby requiring a different type of electric furnace operation, and power supply sources substantially different from those encountered in normal steel melting and siliceous ore smelting furnaces. This paper describes special apparatus for determining specific electrical resistivity of titanium slags, and reports the values obtained on slags encountered in the process of smelting ilmenite ores. In an induction furnace under conditions approximating normal furnacing operation, 25 general heats and 6 special standardization and comparison heats were run. Results indicate relatively low resistivity. Resistivity depends primarily on slag composition, and, to a lesser degree, on temperature. During the summer of 1947 a cooperative project between the National Lead Co. and the Bureau of Mines was conducted at Boulder City, Nevada, in the Electrometallurgical Laboratories of the Bureau. The project involved smelting of ilmenite ores in electric furnaces, and has been reported in detail.' The author participated as a member of the staff of the National Lead Co. during the entire campaign. One outstanding characteristic of the titaniferous slags, their apparently excellent and variable electrical conductivity, was considered sufficiently important to warrant further study. Although little electric smelting of iron ores has been done in the United States, a certain amount of information is available for comparative purposes. Personal experience in smelting siliceous iron ores in electric furnaces furnished further information for comparison. In general, silicate slags are relatively poor conductors of electricity. Current flow during smelting operations may be maintained through a floating layer of coke on top of the slag bath, or through a bath of molten iron, beneath the slag. Silicate slags are not sufficiently conductive to furnish a path for current passage when normal furnace voltages are used. Experimental smelting of a silicate iron ore was undertaken for comparative purposes. A fluid melt was not obtained until the FeO content was reduced to 15 pct. The resistivity increased as the FeO content decreased, FeO compounds being the most conductive of the various oxides in such a normal slag system. The converse appears to be true in slags containing large percentages of TiO2. It has been found that titanium slags become molten with FeO percentages in excess of 30 pct, and that the conductivity becomes generally better as the FeO con-tent of the slag diminishes. This phenomenon was demonstrated in the furnacing operations at Boulder City. During the initial smelting period furnace electrodes could be held immersed several inches in the slag, with tap selectors set for a no-load voltage of 70 v. As the FeO content decreased, the furnace electrodes would "walk up," until at one point in the process the tips would break the surface and arc on top of the slag. This was undesirable since direct arcing caused losses of important flux additions. The slag compositions under study at that time were such that losses due to surface arcing sometimes caused viscous slags to be formed. Forcing the electrodes into the slag bath by manual control to prevent surface arcing resulted in excessive power input and lack of control. Suitable low voltages were not available. Measurement of the electrical resistivity of titanium slags at various operating temperatures and slag compositions was undertaken. It was believed that this information would be of use in the design of electric furnaces suitable for smelting ilmenite, with voltages, electrode sizes, and electrode spacing adapted specifically to titanium slags.

Jan 1, 1951

By A. M. Rowe, I. H. Silberberg

A computer program was written to predict the phase behavior generated by the enriched-gas-drive process. This program is based, in part, on a new concept of convergence pressme, which is then used to select vapor - liquid equilibrium ratios (K-factors) for performing a series of flash calculations. The results of these calculations are the equilibrium vapor and liquid phase compositions which define the phase envelopes. The program was used to predict phase envelopes for 11 different hydrocarbon systems on which published experimental data were available. The predicted and experimental results compare favorably. INTRODUCTION The reservoir engineer is frequently faced with the problem of predicting what will happen if gas is injected into a reservoir. One aspect of this, general problem is predicting the phase changes that will occur when a non-equilibrium gas displaces a reservoir fluid. In particular, a "dry" gas, upon displacing a volatile oil, will pick up intermediate components from the oil. On the other hand, a "wet" gas, containing a high concentration of intermediates, will lose some of these components to a relatively low-gravity, non-eouilibrium1- crude. It is this latter Drocess. occurring in the enriched-gas displacement, which is treated in this paper. In the past, these phase changes have been determined experimentally and the results incorporated into various modifications of the Buckley-Leverett analysis.112 Such experimental work is time consuming, and the results are sensitive to numerous experimental errors. With the wide availability of high-speed digital computing equipment and numerous correlations pertaining to the vapor-liquid equilibria of hydrocarbon systems, it is now practical to calculate such phase behavior. This paper describes a computer program for performing these calculations. THE ENRICHED GAS DISPLACEMENT PROCESS Experimental results have shown that oil recovery can be significantly increased by enriching the displacing gas with intermediate hydrocarbon c0m~onents.3 The essential features of the phase behavior generated by this enriched-gas-drive process are commonly illustrated with ternary diagrams such as Fig. 1.4 In this figure, Gas D, which contains a high concentration of intermediate hydrocarbons with respect to the undersaturated Crude A, is injected into the reservoir. When D contacts A, gas goes into solution until the oil becomes saturated (Point. B). Further contacting of Gas D and saturated Oil B results in a Mixture C which separates into Vapor Y(c) and Liquid X(c). Liquid X(c) is contacted by additional Gas O, resulting in Mixture E which separates into Vapor Y(e) and Liquid X(e). Repeated contacts of the liquid by the injected gas will eventually result in Liquid X(4 of maximum enrichment existing in equilibrium with Gas Y(d). The equilibrium tie-line X(4 Y(4, when extended, passes through the Point D representing the enriched injection gas. For systems of more than three components, the predicted equilibrium states are dependent upon not only reservoir temperature and pressure, but also the compositions of the crude oil and injected gas. If the gas is sufficiently enriched, a miscible displacement is generated. Line If is tangent to the phas,e envelope at the critical point (Point Z) and represents the limiting slope of the tie-lines as the critical state is approached. Point 1 therefore represents the minimum enrichment of injection gas required to generate a miscible displacement. Point G represents the minimum enrichment required for initial miscibility of the injection gas with Crude A. Accra has presented a method to be used for prediction of oil recovery by the enriched gas displacement process.l To develop the phase behavior data needed, he designed the experimental procedure described in the following quotation from his paper: The original liquid was contacted by a volume of displacing gas and allowed to come to equi-

Jan 1, 1966

By P. G. Nahin, A. Grenall, R. S. Crog, W. C. Merrill

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By W. C. Merrill, P. G. Nahin, A. Grenall, R. S. Crog

A progress report of an experimental investigation into the role of clay in reservoir performance is presented. The Paper gives some of the reasons for considering clay as a significant component and outlines the objectives of a broad field of stud) which it is intended to pursue. Descriptions of the analytical methods used are given; these include X-ray diffraction. elec tron miscroscopy, thin section petrography, infrared spec-troscopy, and cation exchange analysis. A suite of the more important clay minerals has been assembled and characterized l~y these methods for use as standards in core analysis. From the data obtained it appears that although no one method of analysis is diagnostic for all of the clay minerals the infrared technique shows considerable promise in this direction. For the present, one or more supplementary methods should be used to confirm the clay mineral identifications. The methods of analysis are applied to field cores taken from repesentative and widely differing strata especially as regards their susceptibility to damage by fresh water. well.; completed in the stevens and Gatchell zones in San Joaquin valley are I,articularly clear-cut examples of this behavior with stevens zone wells being more adversely affected by fresh water. cores from these zones have been studied and are discussed. It appears that differences in this behavior can be ascribed to differences in the nature of the contained clays. The value of the infrarecl spectra of the clay fractions in establishing the identity of the predominant clay minerals is given particular emphasis. INTRODUCTION It is a challenge to the technical resources of the petroleum industry that when the economic limit of production is reached, from 40 to 70 per cent of the oil in California reservoirs remains unproduced even by use of the best presently known methods of recovery. The magnitude of this abandoned volume of oil can be appreciated when it is considered that to 1950 in excess of 8 billion bbll has been produced from California reservoirs with estimated economically recoverable reserves in known fields and pools totaling nearly 4 billion bbl.24 If for every barrel of oil produced there is at least another barrel still in place, it is evident that the revenue obtained from the recovery of only a .few per cent of this volume would repay the cost of the required research manyfold. From well completion experience. production behavior, and a growing body of laboratory data it now appears certain that the mineral composition of a producing stratum has an important bearing on the productivity and ultimate yield. In addition to the organic component and water, the cores con,ist of gravel, sand. silt, and clay" in diverse variety of (a, composition and (b) texture. It is the composite effect of these two factors which is probably responsible in large measure for the way in which the oil flows to the well. The role of the clay and fine-size accessory minerals is not clear but there is a growing opinion, based on their physical and chemical properties, that it is a significant one. of particular importance are the prime facts: 1. The silt and clay fractions of the reservoir matrix possess the highest surface area per gram, and 2. The silt and especially the clay fractions are the most chemically reactive of the inorganic constituents present. Only within the last few years has the knowledge of clay mineralogy and the techniques of identifying the clay minerals reached such a stage as to enable reliable inquiry into the composition of argillaceous sediments.2,8,10,11,12,16,26 It is the purpox of this and succeeding papers to add to the fund of information on the role which these materials play in the production of petroleum from California formations by correlating their presence and associated properties with observed reservoir behavior. In the present paper attention is directed to their possible influence on damage by fresh water. OBJECTIVES The attack on this problem divides naturally into two broad phases: 1. Determination of the nature of the clays and their relationships to the other mineral components, and 2. Determination of the physico-chemical relationships between the clays and the interstitial fluids. In the work described in this paper the emphasis has been on phase 1, which stems logically from the necessity of identifying and understanding the materials to be dealt with in Phase 2. Based on the authors' present opinion that not all of the minerals which occur in oil-bearing formation are of equal importance in their effects on the flow and recovery of oil, it was decided to focus attention first upon the clay minerals content and then. later perhaps. work into the field of the normally larger size non-clay minerals and fractions. The

Jan 1, 1951

By Persifor Frazer

In his " Final Report," Vol. 11, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

By C Woodward

AT the Belmont mine of the Anaconda Copper Min-ing Co., Butte, Mont., a new double-drum electric main hoist and a single-drum electric auxiliary hoist have recently been placed in operation to meet the demand for greater hoisting depths, and to replace a steam-driven hoist which was inefficient and inade-quate for the new conditions. The ease of operation, safety, and efficient consumption of power of the main hoist all tend toward improved hoisting conditions. It consists of a 2150 hp. d. c. motor, directly connected to a shaft carrying two drums equipped with clutches and brakes. The auxiliary hoist consists of a 1000 hp. d. c. motor directly con-nected to a single drum provided with the necessary brakes. Fig. 1 shows the general arrangement of the complete installation, with idler towers and head-frame. The headframe is built of Bethlehem H and G rolled sections, equipped with two 12-ft. dia. cast steel sheaves for the main hoisting ropes. The sheaves are mounted 129 ft., 6 in. above the collar of the shaft; and above them trolleys are provided for their removal or repairs. Between the headframe and the hoist machinery are two idler towers for supporting the ropes on 3-ft. man-ganese steel idlers provided with roller bearings which fleet on a fixed shaft. As a city street is between- the mine headframe, and hoists, it is necessary to protect the thoroughfare from drippings of the preservative compound used on the ropes which pass over the street. For this purpose, at the point where the hoisting ropes cross the street ,a bridge of trusses, supported on columns and roofed with corrugated iron, is provided from property line to property line. Since one of the idler, towers is set close to the street, a part of the structure is built in-tegral with the street covering. The general design of idler tower as well as the covering over the street is shown at A in Fig. 1.

Jan 9, 1927

By Simon D. Strauss

The world appetite for minerals in the, third quarter of this century grew at a higher rate than had been anticipated. To illustrate, consider the experience of four, commodities. Excluding the Communist bloc, sometimes referred to as the centrally planned economies, demand for aluminum increased at a compound rate of 8.6% between 1950 and 1975,; copper rose by 4.4%; iron ore by 5.5%; and tin, the laggard in the group, by 2%. Except for tin, the figures are substantially greater than growth rates anticipated in 1950 in the Paley Commission report and other studies. The growth rate was not evenly distributed in geographical areas. Professor Wilfred Malenbaum of the University of Pennsylvania did an interesting study breaking these figures down as among three principal sources of demand -- the United States, other industrialized nations (which he referred to as the "rich lands"), and the developing world (which he referred to as the "poor lands").

Jan 1, 1982

By W. J. Babyak, J. M. Sheehan, H. W. Paxton

THE- solubility of hydrogen and deuterium in solid niobium up to I-atm pressure has been established bv a number of workers.1-5 X-ray examination at room temperature of specimens reacted in hydrogen at high temperatures from 300° to 1000°C shows the presence of two phases—a bcc phase (a) based on the niobium lattice and with an u0, increasing from 3.30A for Nb to 3.32Afor NbHo.L, and an orthorhombic phase6n = 4.84A, h=4.90A, c =

Jan 1, 1960

By John J. McCabe

INTRODUCTION Over the years, Congress has written into the Internal Revenue Code various provisions aimed at lessening at least one financial burden faced by taxpayers in the mining industry - the federal income tax burden. These provisions include the election to deduct exploration expenses, the election to defer deduction of development expenses, and the percentage depletion deduction. Careful tax planning from the very beginning of a mining venture is essential in taking maximum advantage of these tax benefits. A major decision to be made is the choice of organizational structure. (For a more detailed discussion of this subject, see McCabe, John J., "Developing Structures for Investments in Mineral Property," New York University Institute on Federal Taxation, 42 NYU 24, 1984). One such structure is the use of multiple corporations, with mining activities conducted by one corporation and nonmining activities, such as manufacturing, financing and administration, conducted by the other corporation. This technique, which will be discussed in detail below, can be particularly advantageous in delaying recapture of previously deducted exploration expenses and in maximizing depletion deductions. TAX BENEFITS IN MINING Exploration Subject to certain restrictions discussed below, exploration expenditures (i.e., expenditures paid or incurred during the taxable year for the purpose of ascertaining the existence, location, extent, or quality of any deposit of ore or other mineral, and paid or incurred before the beginning of the development state of the mine are deductible at the election of the taxpayer (Section 617(a)).* Were it not for this option, exploration expenditures would be required to be capitalized and recovered through depletion, after production begins. Exploration of a mineral deposit can be very costly and may not result in commercial production for some time. If the taxpayer has income to he offset by the deductions, a mining venture can usually be structured in such a way as to allow the offset of mining losses against the other income. With today's high interest rates, this election can be quite valuable in present value terms. Corporate and noncorporate taxpayers are subject to different restrictions on this tax benefit. Corporations may elect to deduct only 85 percent of eligible exploration expenditures (Section 291(b)). (The Tax Reform Act of 1984 reduced this to 80 percent effective for expenditures after December 31, 1984, in taxable years ending after such date). The remaining 15 percent (20 percent after December 31, 1984) is capitalized and recovered at the same rate as five-year ACRS property (Section 291(b)). Individual taxpayers are not subject to this 85 percent rule; however, any amount deducted in excess of ten-year straightline amortization is a tax preference item for individuals (Section 57(a)(5)). Individuals may avoid the tax preference by electing to capitalize exploration expenditures and amortize them over ten years (Section 58(i)). In order to prevent the taxpayer from, in effect, converting ordinary income into capital gain by selling property that has given rise to exploration expense deductions, the Code requires recapture of such deductions upon the occurrence of certain events (Section 617): 1. Upon disposition of the property, adjusted exploration expenditures are recaptured to the extent of gain realized on the disposition (Section 617(d)). 2. If the property is leased, the lessor is disallowed any depletion deduction until his adjusted exploration expenditures have been recaptured in the form of foregone depletion deductions (Section 617(c)).

Jan 1, 1985

By Charles L. Elliot

Data on mining applications of geophysical activity in the Free World in 1964 have been made available to SME again this year by the Society of Exploration Geophysicists. Worldwide data were collected as part of an annual service to the mining industry by the Committee for Geophysical Activity of SEG. Data are taken from 245 voluntary responses (53%) to questionnaires circulated to 463 company, government and university organizations engaged in mining geophysical operations and research all over the world. WORLD ACTIVITY Worldwide manpower utilization totalled 9323 professional man-months and $14.5 million was reported spent in mining geophysical activity in 1964. This is up from 9078 man-months and $12.6 million in 1963 and 8065 man-months and $12.8 million in 1962. Worldwide geophysical activity in terms of manpower utilization and expenditures is presented in the accompanying table.

Jan 9, 1965

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix. Few of the operating companies in the Florida phosphate district have applied isopachous (Greek isos, equal and pachys, thick) to mapping. The writer believes there is a need for the techniques discussed herein and that they can be applied to mapping other geologically similar areas in either economic or scientific investigations. The land-pebble phosphate district of Florida occupies a compact area in the west-central part of the state. It includes mainly the following land survey divisions: Ts. 27 S. through 32 S. and Rs. 20 E. through 26 E. The town of Mulberry, Fla., is in the approximate center of the district. The strata of the area, which is part of the Gulf Coastal Plain, occur in thin formations with broad outcrop belts, and low dips. The topography is subdued and gently rolling with three marine terraces, which are found at 30, 100, and 150 ft above sea level,' accounting for most of the relief. Occasional small sinkhole lakes are present, most of them above the 150-ft shoreline. The phosphate deposits occur in unconsolidated sediments such as clays, sands, and sandy clays. They are overlain by a heterogeneous assemblage of sands, clays, muck, and iron-cemented sand, easily penetrated, in most cases, by a hand auger or drill. Limestone, locally called bedrock, or a calcareous bedclay, thought to be a residue of the limestone, directly underlies the phosphate deposits. General Requirements Most companies and independent prospectors operating in the district have furnished prospecting data to the U. S. Geological Survey. The information is recorded on either field logs or prospecting maps and includes the following information for each hole drilled: location of the hole, thickness of the overburden, thickness of the matrix, phosphate content in long tons per acre, grade of the phosphate content expressed as the percentage of bone phosphate of lime (P2O5 x 2.18) or BPL, and the per- centages of iron-aluminum oxides and insolubles. The phosphate is classified according to size as either pebble or flotation material. The milling processes of the companies vary, and the size classification is necessarily different in many cases. However, pebble may be considered as larger than 14 mesh and flotation material as smaller than 14, but larger than 150 mesh. Some prospecting data include the exact depth at which bedrock or bedclay was reached, and these figures greatly increase the reliability of the data both for isopachous mapping and for mapping the basement. A drilling density of four holes per 40 acres of land furnishes a minimum amount of data for isopachous and related mapping. From the minimum of four, densities up to 32 holes per 40 acres are used. The various drilling densities may influence the choice of the proper scale. Selection of the proper scale is dependent upon the known drilling densities, the subsurface variations to be shown, the extent of the area to be mapped, and the detail desired in the completed map. Scales of 1:24,000, 1:4800, and 1:2400 are used in isopachous and related mapping by the Florida Phosphate Project. The 1:24,000 scale is used most effectively with drilling densities not exceeding eight holes per 40 acres. The subsurface variations should be relatively low and uniform, permitting the use of smaller intervals without undue crowding of the lines. Comparatively large areas can be mapped on this scale, but minute detail is necessarily sacrificed, because the information is drawn from a maximum drilling density of only eight holes per 40 acres. Isopachous and related maps of the 1:4800 scale are made of areas on which the drilling information covers from 4 to 16 holes per 40 acres. Moderate subsurface variations with relatively sharp gradations can be shown accurately. The area represented by the maps is reduced considerably in favor of detail. The 1:2400 scale is most frequently used by the Florida Phosphate Project. It lends itself particularly well to isopachous and related mapping, being easily adapted to the multiform drilling data available. Maps of this scale are prepared with information ranging from 4 to 32 holes per 40 acres; however, use of the minimum drilling density on the

Jan 1, 1952

By Robert L. Marovelli

A recent reorganization placed the health and safety research activities of the Bureau of Mines under a director, Division of Minerals Health and Safety Technology. The new health and safety research organization and its position in the Bureau hierarchy is shown in Table 1.

Jan 11, 1979

By RALPH HAYES SWEETSER

ONE per cent. of ash in a ton of coal has been so little considered that in many circles it has been positively ignored. Even P. T. Barnum had never heard of it, or he would have had one on exhibition alongside the Cardiff Giant and the White Elephant. One per cent. of ash is closely related by both those freaks of Barnum in that it is "stone" and, in its aggregate, it is the greatest "White Elephant" that the American public now supports. Some of you may have paid Mr. Barnum for a look at the "petrified man" (named the Cardiff Giant by the gullible wise men of the early seventies); but it is certain that everyone of you is now paying for the support of the great White Elephant that is being constantly carried by our railroads all over the country-at the public's expense. " One per cent. of ash in a ton of coal" requires 120,000 open-top railroad cars each year to transport this use- less stone giant from its native bed in the coal seams of the bituminous regions to the coal bins of the consuming public.

Jan 1, 1924

By J. T., Norton

As cold working is an important feature in a great many of the fabricating processes now applied, this paper presents some ideas on the nature and results of the plastic deformation produced in this operation. The art of manufacturing metal for practical uses is very old and has undergone very great development. The science of metals has- also developed very rapidly recently and the various processes to which metals are submitted are much better understood now than they were even a short time ago. All the knowledge that can be obtained on this subject is useful because it promotes efficiency in converting metal into finished articles.

Jan 1, 1927

The following list comprises the names of those persons who became members during the period May 10, 1919, to June 10, 1919. ALAYZA, CARLOS Box 850, Lima, Peru, S. A. BALLARD, P. A Surveyor, Midwest Refin. Co., Custer, So. Dakota. BARNEBL, A. J., JR.... Mech. Eng., The Dorr Co., 101 Park Ave., New York, N. Y. BILLINGS, GOODSELL Platteville, Wis. BRONSON, C. B., Mech. & Met. Engr., New York Central Lines, Room 1520, Grand Central Terminal, New York, N. Y. BUNCE, E. H Met., The New. Jersey Zinc Co., Palmerton, Pa. CHARLTON, D. E. A., Editorial Staff, Engrg. & Mm. Journals 10th Ave. & 36th St., New York, N. Y. DAVIS, JOHN N., Supt. of Mills, Engels Copper Min. Co., Engelmine, Plumas Co., Cal. DUKES, GLENN H., Chief Engr., The Sunday Creek Coal Co.,1001 Outlook Bldg., Columbus, Ohio. ERICKSON, ARTHUR .... Engr., United Smelt., Refin. & Min. Co., Mldvale, Utah. FLYNN, A. E Supt., Rand Consolidated Mines, Ltd., Goudreau, Ont., Canada. HIBBARD, WALTER R 63 Ashley St., Bridgeport, Conn. HOBSBAWN, I. BERKWOOD, Cons. Tech. Chem., Messrs. Gibbs. & Co., Valparaiso, Chile, S. A.

Jan 7, 1919

Albin, B. R Billings, Mont. '28 Amster, Nathan L . , 25 Broad St, New York, N. Y. '28 Bache, Jules S 42 Broadway, New York, N. Y. '28 Barrett, C. P 5338 Harper Ave, Chicago, Ill. '28 Baum, Frank G Hobart Bldg., San Francisco, Cal. '28 Bayless, Ron. William S Russ Bldg , San Francisco, Cal. ' 28 Bean, Louts H., V.P., Dwight P. Robinson & Co, Inc 125 E. 46th St, New York, N Y. '23 Beatty, Ross J 1105 First National Bank Bldg., Chicago, Ill. '28 Benwell, Oswald F 205 Colorado National Bank, Denver, Colo. '28 Beymer, Albert S., V.P., Keystone National Bank Pittsburgh, Pa. '28 Bingham, Charles W 1542 Hanna Bldg, Cleveland, Ohio. '28 Blumenthal, Hugo 44 Pine St, New York, N. Y. '28 Boettcher, Charles Ideal Cement Bldg., Denver, Colo. '28 Bowlus, Thomas H Iola, Kans. '28 Bragg, E. B Carmel, Cal. '28 Brown, Colvin B Chamber of Commerce, Washington, D. C. '28 Burt, Maxwell Struthers Southern Pines, N. C. '28

Jan 1, 1923

The following is an incomplete list of members and guests who called at Institute headquarters during the period Oct. 10, 1918 to Nov. 10, 1918. J. Carson Adkerson, Virginia. George H. Parsons, Hayden, Ariz. Andrew B. Armstrong, Connecticut. W. E. Pomeroy, New York. Courtenay DeKalb, San Francisco. Ezra C. Rider, Bisbee, Ariz. Clifford G. Dennis, San Francisco. H. W. Seaman, Chicago, Ill. Rudolph Emmel, Boston, Mass. William Allen Smith, Northampton. Emil Gathmann, Baltimore Md. R. K. Stockwell, Salt Lake City, Utah. Ernest S. Geary, Denver, Colo. W. G. Swart, Duluth, Minn. W. E. Hopper, Washington, D. C. Kirby Thomas, New York. W. Spencer Hutchinson, Boston, Mass. - Warren D. Thompson, Harvard Club. E. W. Kohl, Jr., Philadelphia, Pa. H. Vincent Wallace, Los Angeles, Cal. E. C. Nighman, Butte, Mont. Paul T. Benson, formerly with the Tacoma smelter, has resigned his position there to accept one with the Great Metals Mining and Milling Co. at Nespelem, Wash. Prof. Edward E. Bugbee, of the Mining Department of the Massachusetts Institute of Technology, has been granted a leave of absence to accept the position of Assistant Director of Education for the S.A.T.C. of five southern states with headquarters at Raleigh, N. C.

Jan 12, 1918

Page McGREGOR, A. G.-Features of the New Copper Smelting Plants in Arizona. Discussed by L. D. Ricketts, E. P. Mathewson 2145 HOWARD, L. O.-The Basic-Lined Converter in the Southwest. Discussed by Walter Douglas, E. P. Mathewson, Kuno Doerr 2145 SAMUEL, J. MOORE-Determination of Dust Losses at the Copper Queen Reduction Works. Discussed by Walter Douglas, E. P. Mathewson, S. J. Jennings, C. E. Arnold, A. G. McGregor, L. D. Ricketts 2148 MORSE, H. W., AND TOBELMANN, H. A.-Leaching Tests at New Cornelia. Discussed by H. W. Morse, Lawrence Addicks, G. D. Van Arsdale, S. J. Jennings, F. S. Schimerka, C. G. Grabill, F. N. Flynn, Stuart Croasdale 2151 LAIST, FREDERICK, AND ALDRICH, HAROLD W.-The 2,000-Ton Leaching Plant at Anaconda. Discussed by F. N. Flynn, E. P. Mathewson 2159 ADDICKS, LAWRENCE-Possibilities in the Wet. Treatment of Copper Concentrates. Discussed by F. N. Flynn 2160

Jan 12, 1916

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product and the Hanna Mining Co.'s Groveland plant on the Upper Peninsula of Michigan is no exception. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper and various iron silicates.1 Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals.2 Flotation of the spiral tailings makes up about 75% of the concentrate, while a minor amount of concentrate (less than 3%) is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tpy. The initial concentrating facilities were constructed in 1958 and the concentrate was marketed as sinter feed until a pelletizing plant was added early in 1963. Grade improvement soon became a high priority research project, and several methods of concentration were investigated.

Jan 3, 1968

By Myers, J. F.

The purpose of the mill tests reported herein, was to determine the relative power efficiency of fast and slow rod mill speeds on the ores of the Tennessee Copper Co. The tests were carried out at the lsabella Mill of the Tennessee Copper Co. under normal operating conditions. Every effort was made to keep the ore supply and other conditions constant, but it will be noted that some slight variation did occur. The open circuit 6 by 9 rod mill, and ore, used in these tests have been previously described.' Four motor drive pinions were available and the tests were performed in the following manner: each pinion was used to drive the mill for a period of one week. Constant sampling prevailed during the test run, and a composite sample for each speed test was made. Realizing that some slight liner wear took place during the four-week test-run, and that some slight variation of the ore may have taken place, a second and then a third series of four-week test- runs were made with the four different pinions. The screen analysis of each of the thee-week run samples at the various speeds were composited and the results are shown in Table 1. The authors feel that the 12 weeks of operation consumed during these test-runs would represent fairly the effect of each mill speed. The data of line 37 show that within the error of sampling and plant operation, the tons of minus 65-mesh material generated per horsepower hour was the same at all four speeds.

Jan 1, 1949