Search Documents

By John A. Mathews

During the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table, stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also Iisted in the table, was said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed a new oil furnace; when asked what became of the products of combustion, he replied: "There ain't any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20' and 100" C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for l° C.; cast aluminum (99.93 per cent. AI.),

Jan 1, 1922

By John A. Mathews

During the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table, stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also Iisted in the table, was said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed a new oil furnace; when asked what became of the products of combustion, he replied: "There ain't any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20' and 100" C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for l° C.; cast aluminum (99.93 per cent. AI.),

Jan 1, 1922

By H. W. Maynor, C. J. McHargue

DURING the course of an investigation of materials suitable for use as thermocouples at elevated temperatures by one of the authors, several nlolybdenum-rhenium alloys were prepared. Micrographs of an annealed alloy containing 25 pct Re (intended concentration; analysis not obtained) showed a number of twins, Fig. 1, suggesting a face-centered cubic structure. This note reports the structure and recrystallized wire texture of an alloy containing 25 wt pct Re. Alloys were prepared from 99.9 pct Mo (Fansteel Metallurgical Corp.) and rhenium obtained from the University of Tennessee (purity unreported). Powders were combined and briquetted at 56,000 psi and sintering was carried out at 2400°C for 5 hr in vacuum. Ingots so prepared were swaged at 982.2" to 1037.8oC into wires 0.036 in. diameter, a reduction in diameter of 85.6 pct. These wires were vacuum-annealed 1 hr at 2000°C. A North American Philips 114.59 mm powder camera and nickel-filtered copper radiation were used for structure determination. For the texture determination a Laue-type camera was used with zirconium-filtered molybdenum radiation and, because of the high background, aluminum foil was mounted next to the film. Exposures were taken with the wire perpendicular to the X-ray beam and tilted by 10". It was found that the X-ray pattern could be indexed on the basis of a face-centered cubic structure. Because of difficulties associated with obtaining a good X-ray pattern for this material, accurate parameter determinations were not made. An indicated parameter value of 3.70A was obtained. The X-ray data are given in Table I. The annealed wire texture was observed to be a sharp [111] texture. The spread about this fiber axis was k8" at the surface of the 0.036 in. wire. The annealed wire textures of aluminum have been reported as retention of the [Ill] deformation texture for anneals below 500°C and a new [1121 texture for anneals above 600°C.1 In copper wires, with a [Ill] plus [loo] deformation texture, results indicate a retention of this texture for annealing at lower temperatures and new components or the disappearance of components for annealing at higher temperatures.' The presence of the strong [I111 texture in the molybdenum-rhenium alloy after a 2000 °C anneal suggests that the deformation texture was the same. Acknowledgment The wires used in this study were prepared and heat-treated at the Institute for Atomic Research, and Ames Laboratory, Iowa State College, and the authors wish to express their thanks to the Institute for allowing the use of the material and permission to publish the results.

Jan 1, 1954

By T. Egleston

THE materials containing copper which are refined in the United States, are, for the most part, the native, coppers of Lake Superior. Until quite recently but little pig copper was made for sale, and that came principally from the pure sulphurous ores of New England and the South, and was generally sold to refineries not far from the ore furnaces. A small amount found its way into the market which was produced either as the by-product of the treatment of gold and silver ores, or as the result of the treatment of impure copper ores; but both these grades, on account of the impurities they contained, were looked on with suspicion, and were not sought for. All the grapes of pig copper are sold by the unit of copper contents, a great reduction being made in the price when impurities are present. There are at the present time only three works which treat native copper, the two of the Detroit and Lake Superior Copper Company, and the works of C. G. Hussey & Co., in Pittsburgh. There are a few works which smelt sulphurous ores and refine their pig; besides these there are a few small works where pig copper is refined only. Some of these purchase black copper, refine scrap, or simply refine such grades of ingot copper as are found in the market, but mostly that from Lake; Superior, for the purpose of getting it into such shapes that can be handled commercially to advantage, such as in making large plates or high grades of wire for electrical purposes. A number of such works are situated in the Naugatuek Valley and elsewhere in New England. The recent discovery, of valuable ores in Arizona makes it probable that within a few years the refining of copper in the United States will make great developments. Up to the time of the discovery of the mines on Lake Superior, only a very small quantity of native copper had ever been found, not sufficient to justify the erection of works for its special treatment. It had, besides, never been found in very Large masses, so that the discovery of great-blocks of it presented serious difficulties, not only in mining it,† but in bringing it into a merchantable condition. It seemed a very simple process to melt these large masses, * Road at the Lake Superior Meeting, August, 1880. †Transactions American Institute Mining Engineers, vol. vi, page 2S2.

Jan 1, 1881

By Thomas N. Walthier

If current trends continue, the shrunken world of exploration will keep on shrinking and the number of new mines will be insufficient to meet production requirements. Mineral shortages-not natural, but government induced-will then occur.

Jan 5, 1976

By H. D. Strain

Potash is a generic term used to describe a number of compounds containing the element potassium (K), which is one of the three major plant nutrients. Potash content of these compounds is commonly expressed as percentage potassium oxide (K20), and the market value of the products is usually dependent on contained K20. Most of the potash produced (approximately 95%) is used in agriculture as fertilizer. Potash products today are shipped by producing countries all over the world to meet the need for increased food production. WORLD POTASH RESERVES Apparent world potash reserves are shown in Table 15.2B.1 and total some 96 billion mt of recoverable potassium oxide. The Canadian reserves account for approximately one-half the known world reserves. The reserves shown represent the potassium oxide content of a variety of potash-bearing ores. The major ore is sylvinite (a mechanical mixture of KC1 and NaCl) from which KC1 or sylvite is recovered (63.2% K20 equivalent). Other ores, such as langbeinite (potassium, magnesium sulfate-22.7% K20) and carnallite (potassuim magnesuim chloride-17.0% K20) are also mined in various parts of the world, mainly for the potassium content. Theoretically, potassium is available in almost unlimited qualities from brines and saline waters. To date, the cost of recovery from salt brines has been greater than the costs by mining operations, but new technology could make brines and seawater an increasingly important source. POTASH PRODUCTION Potash production dates back to the 1860s in Germany, which was the only recorded producing country until 1912. By 1912 Germany was producing approximately 1 million tpy of K2O equivalent. Production began in France in 1913 and in the United States in 1915. World potash production and consumption are shown in Table 15.2B.2 for the years 1950-51 through 1967-68. In 1967 and 1968 the major potash-pro¬ducing countries in order of importance were those listed in Table 15.2B.3. By 1972 Canadian production had outstripped U.S. production. WORLD CONSUMPTION World consumption of potash for the years 1950-51 through 1967-68 is shown in Table 15.2B.2. Table 15.2B.4 shows total world consumption of potassium materials in 1967-68 by country. More than 70% of the world's potash is

Jan 1, 1976

(Separates of all the Pamphlets published within the last three years (starting with No. 1469) are available, with few exceptions, at Institute headquarters. Separates of all the Technical Publications are also available. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.] METAL MINING TRANS. PAMPHLET VOLUME NUMBER TITLE AUTHOR MEETING AND PAGE'S 1033 Relation of Air Pressure to Drilling H. W. Seamon New York 66, 743, 756 Speeds of Hammer Drills Feb., 1921 1034 Time Factor in Depletion of Mines J. W. Roberts New York 66,711 Feb., 1921 1035 Calculation of Ore Tonnage and Grade J. E. Harding New York 66, 117, 122 from Drill-hole Samples Feb., 1921 1038 Discussion of Papers Presented in 1920 1041 Run-off and Mine Drainage H. N. Eavenson New York 66, 624,630 Feb., 1921 1043 The Health of the Underground Worker A. J. Lanza New York Feb., 1021 1045 Dust-ventilation Studies in Metal D. Harrington New York 66, 272, 289Mines Feb., 1921 1046 Discussion of Papers Presented at New York Meeting, 1021 1072 Breakage and Heat Treatment of Rock- B. F. Tillson New York 66,1758 drill Steel Feb., 1921 1073 Discussion of Papers Presented at New York Meeting, 1921 1076-M Analysis of Some Drill-steel Testa F. B. Foley New York 66, 789 Feb., 1921 1077-M Application of Magnetic. Analysis to C. W. Burrows New York 66, 796 Rock Drills Feb. 1921 1078-M Heat Treatment of Rock-drill Steel G.H. Gilman New York 66, 779_ Feb., 1921 1080 What is the Ideal Drill Steel? F. H. Kingdon New York 66,807 Feb., 1921 1051 Rock Drill Steels, etc. - W. T. Ober New York 66,814 Feb., 1921 1082-C Underground Mine Development, Its J. B. Dilworth Wilkes-Barre 66,715, 7.21 Definition and Valuation Sept., 1921 1084 Drill Steel from Hollow Ingots P. A. E. Armstrong New York, 66, 809 Feb., 1921 1088 Authors' Replies to Recent Discussion 1092 Heat Treatment of Rock Drill Steel A. E. Perkins New York 66,811 Feb., 1921 1096-M Octagonal Ventilation Shaft. of Davis- J. L. Bruce Wilkes-Barre 66, 252, 268 Daly Copper Co. Sept., 1921 1100-C Determination of Electrical Equip- G. Bright Wilkes-Barre 66, 580, 605 ment for a Mine Hoist Sept. 1921

Jan 1, 1927

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of September, 1913: Members. ANDERSON, ANDREW P., Min. Engr 908 Story Bldg., Los Angeles, Cal. ANDROS, STEPHEN 0., Min. Engr University of Illinois, Urbana, Ill. BECKETT, PERCY G., Min. Engr Globe, Ariz. BLAIR, THOMAS S., JR., Prest. Blair Engrg. Co 343 S. Dearborn St., Chicago, Ill. BOYLE, HARRY, Min. Engr S07 Lowman Bldg., Seattle, Wash. BRADEN, EUGENE B., Vice-Prest., Selby Smelting & Lead Co., Merchants Exchange Bldg., San Francisco, Cal. CHALMERS, JOHN W., Min. and Elec. Engr., Morro Velho, Villa Nova de Lima, Honorio Becalho Minas Geraes, Brazil, So. America.

Jan 10, 1913

By G. S. Cole, G. F. Bolling

A series of Al-Cu alloys has been cast from constant superheat to solidify either with a hot top or with a free liquid/air interface. All the other variables which affect relative fluid motions were kept constant except the imposition of slow rotations m oscillations of the mold. Depending upon the exact circumstances, evi-dence could be found for the nucleation of equiaxed grains from dendrite bits detached from the columnar zone, or from the free surface, or from solid bits induced at pouring; a special experiment showed the solute buildup during ingot solidification and by inference the reality of constitutional supercooling. All methods of grain nucleation are thus supported. When solidification is arranged in a static mold the columnar- to-equiaxed transition occurs by one of these nucleation paths, subject to the natural decay of temperature gradients which promotes nucleation or the survival of nuclei. But when solidification is forced under special fluid flows it may display odd transitions. In one of these the equiaxed zone is synihesized from. dendrite bits detached from the solid/liquid interface. These survive under the concurrent lowering of temperature gradients and eventually cause transition by impeding columnar growth. GRAIN structure control is desired because real experience shows that specific properties are associated with specific cast grain structures. But since control is thus a matter of need and does not require understanding, much of casting remains art. For example, the manipulation of relative fluid motions in simple ingots provides a control of grain structure development,1-4 but theoretical insight is not required in order to broaden its potential applicability. Fortunately, however, once a variable like fluid flow is recognized it can also provide paths toward new insight. New observations using this variable have provided an insight which is curious. All the theories or descriptions of the columnar-to-equiaxed transition (CET) seem to be supported as long as the appropriate experiment is carried out. In order to develop this idea, let us ignore segregation, the chill zone (until a later section of this paper), and the origin and development of the columnar zone.= The details of questioning how equiaxed material forms in a casting may be divided in two. The first part is simply a questioning of the origin for equi-axed grains: are there fresh nuclei from heterogeneous nucleation, or dendrite bits broken off or melted from the columnar zone or elsewhere,6 or other solid bits surviving from the outset of freezing? The second is more complex, a questioning of the CET: does columnar growth slow down and allow the dominance of equiaxed grains, however they are formed, or do equi-axed grains take over and force columnar growth to stop? This "chicken-or-the-egg" second question can be quite useful, especially because it allows us to delineate the ordinary or NATURAL EQUIAXED ZONE and the induced or SYNTHETIC EQUIAXED ZONE. A natural equiaxed zone occurs if solidification proceeds in the absence of disturbances or extraneous forces such as ultrasonics, stirrings, and so forth. Both the CET theory proposed by Winegard and Chal-mers, 7requiring constitutional supercooling, and the CET theory suggested by Chalmers,8 requiring nuclea-tion only on pouring, pertain to the natural equiaxed zone. The best collating evidence to date for both these theories is contained in the work by Biloni and Chal-mers;9,10 the former theory7 is supported by special versions of the unidirectional growth experiment performed by Plaskett and winegardl1 and the latter theory' is supported in detail for the solidification of small ingots. An equiaxed zone can be synthesized when disturbances caused by forced fluid flows2-4 or other artificial means9,10 break off or melt off dendrite tips from an advancing solid/liquid interface,* if (and only if) temperature gradients in the melt are (forcibly) reduced enough to ensure the survival of these bits of dendrites, 2'3 Willful disturbances even so trivial as those produced by rapping a mold might be included here; as will be shown for example, this follows Southin's suggestion that the free liquid/air interface

Jan 1, 1970

By F. J. Cuddeback

For low-head pumping of small quantities of water, the water jet, or hydraulic educter, has been used to advantage by Eagle-Picher Mining and Smelting Co. in the Tri-State district. Water-jet pumps are used for draining sumps and pockets up to 15 ft. in depth. They have been used very successfully when only moderate amounts of water are encountered in taking up bottom. A small, easily handled unit is desirable in this work, especially while opening and deepening a new stope. Small air pumps are convenient but can be used only on the day shift, when air is available. Obviously, a jet pump of smaller capacity but operating 24 hr. prevents lost time at the start of each shift. No tests have been made on their power efficiency, but admittedly it is low. However, for certain kinds of work this is offset by their handiness, low initial cost, low upkeep, and reliability. They will handle slime and sand without ill effect, and will continue to pump indefinitely on air. This foolproof 24-hr. performance has led to their continued use at some places even after electric pumps with better power efficiency could have been installed. The success of jet pumps depends largely upon a cheap source of high-pressure water. Owing to mine depths in the Tri-State district, pump pressures range from 100 to 150 Ib. per sq. in. In many mines it is common practice to handle the normal inflow water with triplex pumps ranging in size from 3 to 8 in. The pumps operate 24 hr. per day, and, in order to handle emergency conditions, are speeded slightly faster than necessary to pump the normal inflow. The sump level is governed by controlling the by-pass water with a butterfly valve and float. This method is somewhat wasteful of power, but permits the pumps to operate with a minimum of attention. Such an installation is visited once a day to check lubrication. Hence, if some of this water, normally by-passed to the main sump, were used to operate a jet pump, the power cost could be considered low regardless of efficiency. Figs. I and 2 show two water jets that have done satisfactory work. The one in Fig. 2, made up entirely of pipe fittings, may be of interest partially because of its novelty, but does better work than its appearance indicates. The pipe fittings for this jet as shown cost $2.20. Some improvement in its design may be made by cutting out the 135 by 1¼-in. reducer to a smoother taper as shown by dotted lines. A 3-in. suction pipe is sometimes used in order that the discharge may be as straight as possible. A 2-in. discharge line has been used frequently, but 3-in. pipe is used where several hundred feet of discharge is required.

Jan 1, 1946

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical specifications, color demands must also be met. The firm of which I have the most knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By R. A. L. Black

Between March and June 1962, the privilege of holding a Carnegie Corporation Fellowship enabled R. A. L. Black to travel extensively in the northeastern and western U.S. and in Canada, seeing mining schools, mining research establishments and a cross-section of the American and Canadian mining industry. Visits were paid to 12 university mining schools, 7 research establishments and 19 mining operations. The author had previously spent two months in Britain in a similar manner and eventually returned to his home in South Africa after a short period studying mining problem in Australia. Thus, although the following remarks are mainly concerned with the educational problems of mining in North America, a comparison of impressions of American and Canadian conditions could be made with impressions gained from first-hand experience of other mining centers in the English-speaking world. The conclusion was reached that the problems and conditions of mining, research and mining education are very similar in all areas visited.

Jan 4, 1963

By W. J. Taylor, H. J. Mutz, A. F. Brock

THE International Kickel Co. of Canada Ltd. operates five underground mines and an open pit. Four of the mines, the Frood-Stobie, Creighton, Murray, and Garson, are on the south range of the Sudbury Basin, map above, within a radius of 10 miles of the city of Sudbury, Ontario. The fifth mine, the Levack, is on the north range of the Sudbury Basin, 30 miles to the northwest of the city. The open pit is operating on surface ores of the Frood-Stobie orebody. Two pits were opened at the Frood-Stobie mine; the Frood section was started in 1938 and the Stobie section in 1942. To meet the heavy demand for nickel during World War 11, open-pit production was accelerated until it constituted over 40 pct of Inco's total tonnage. As a consequence open-pit ore was depleted considerably alhead of schedule; the Stobie pit was completed in the summer of 1951, and it is expected that mining at the Frood pit will be completed in 1953. The major program launched 10 years ago to develop additional underground production as a replacement of open-pit tonnage thus had to be greatly speeded up. This conversion to all-underground mining will be completed within the next two years, and the underground mines will then have an annual hoisting capacity of 13,000,000 tons. One of the new mines in the underground expansion program, the Murray, was brought into production in 1950. Ore production from the new Stobie section of the Frood-Stobie mine was commenced on a limited scale in 1951 and will be increased as the program progresses. Delivery of ore to the new Creighton mill was started in the summer of 1951 from the caving project launched at Creighton mine. When mining was started in the Sudbury district 65 years ago the ore deposits were opened on a small scale and mining methods conformed to a general pattern of small open cast pits, followed by open stopes as mining was extended below the pits. The open stoping methods used were heading-and-bench and shrinkage. In certain cases a type of cut-and-fill mining was used with drywall tramways and dry-wall chutes in the fill. As the mines were deepened,

Jan 1, 1954

By Reginald Williams

THE amount or value of the precious metals consumed in dentistry is probably amazing to most people. It falls very little short of that which is consumed in jewelry. Inasmuch as the ultimate destination is in the human mouth, dental alloys enjoy some importance because life and health depend upon restorations made with them. Prosthetic dentistry has made wonderful progress in the last few years. The manufacturers who supply the metals also deserve commendation. This industry which deals with metals to go-into people's mouths is comparatively new. There is no literature on the subject, and little or no precedent by which to be guided. It was only by close cooperation with the dentist or prosthetic technician that desirable physical properties were produced, as-nearly as possible, in the metals which were available and permissible. It is true that there were and still are conflicting opinions among the dentists as to the physical properties they require. Sometimes they request the impossible, such as alloys which are exceedingly stiff and springy, yet will bend or adjust easily. Even in this latter instance, progress has been made by supplying methods of heat-treatment whereby metals may be softened or hardened at will. (Figs. 1 and 2.) The demands made upon manufacturers are extremely varied. They must supply metals of tensile strengths ranging from approximately 30,000 to 100,000 lb. per sq. in. and over. The latter metals must be workable and in many instances capable of extreme deformation. They must not be affected by mouth conditions, nor should they oxidize greatly when molten, at red heat, or during a soldering operation. In addition to physical, specifications, color demands must also be met. The firm of which I have the most, knowledge manufacturers 11,553 standard stock articles of precious metals, taking into consideration formulas, finenesses, grades, colors, gages, lengths, sizes and weights. If special demands are taken into consideration, the number would be in excess of 25,000. Wrought metals are manufactured in a great many alloys of different sizes and shapes, such as plate, bar, rod, wire, sheet, strip, mesh and foil. There are also other products of importance.

Jan 1, 1928

By A. T. Yu

As the first loads of Noamundi iron ore rumbled into the new 54-in. Gyratory Crusher on March 30, 1968, one of India's largest and most modern iron ore processing complexes began operations. The completion of the $13 million mining and processing complex brought to a successful conclusion the second chapter of a phased expansion program initiated in 1958 by India's gigantic Tata Iron and Steel Co. The completed complex will yield annually 2.5 million tons of washed, sized ore and sinter fines destined for Tata's furnaces at Jamshedpur. Hewitt-Robins Div. of Litton Industries was awarded the turnkey project on the basis of world- wide competitive bids. Eighty miles southwest of the city of Jamshedpur, Noamundi lies on an approximate geographic grid of 22º-5' latitude north and 85º-30' longitude east. The mine is approximately 600 ft above sea level.

Jan 11, 1968

By R. R. Harvey

Recent evidence has indicated that the films forming at crude oil-water interfaces are the result of naturally occurring su,rface-active components in the crude oil rather than oxidation products resulting from exposure of the oil to air. Since the presence of such films may strongly affect the displacement of oil from porous media, a knowledge of their composition and formatiorz is of fundamental importance. In this study, without the assumption of a specific mechanism, film formation is considered to involve the transfer of a weakly surface-active species in solution in the oil to the oil-water interface. The film gas law and the Gibbs adsorption equation may thus he applied to the system. The rigid films which form upon decrease of the oil-water interfacial area are considered a result of the very slow rate of re-solution of the film material into the oil. When the shrinkage of the interface is very rapid, the amount of film material leaving the interface is negligible, and the system may then be treated in the same manner as an insoluble film. The combination of these treatments leads to a new concept of the film factor in which it may he quantitatively related to the concentration of film-forming material at the interface. Suitable experiments can then yield the following information. 1. Original concentration of surface-active species in the oil. 2. The change of concentration with time. 3. Concentration of surface active species at the interface. 4. The change of this concentration with time. 5. Interfacial tension of the system at any time and its variation with time. 6. Equilibriunz concentrations for a given set of conditions. 7. Concentration requirements for solid film formation. 8. Molecular diameter of the adrorbed species. These calculations may be made solely from data taken from measurements on the original oil. While using the pendant drop method of interfacial tension measurement of crude oil-water systems, Bartell and Niederhauser' remarked on the thin, transparent, pliable, solid films or membranes which were often formed at the interface between crude oil and water. As a result of their observations of these films, Bar-tell and Niederhauser concluded: 1. The films are formed by material from the oil adsorbed at the interface rather than by a reaction at the interface. 2. The adsorption of the film-forming material is a rather slow process. 3. There are good indications that the process is reversible; i.e., the film constituents may re-dissolve into the oil. 4. The film will spontaneously spread over any new surface formed. 5. The process of adsorption at the interface is accompanied by a decrease in the interfacial tension of the system. Although they had proved that film formation was not due to a reaction at the interface, Bartell and Niederhauser were unable to demonstrate conclusively whether these film-forming constituents were present in the original reservoir oil or whether they were formed as oxidation products after exposure of the oil to air. Recent evidence seems to point to their presence in the original oil. Although the true nature of the film-forming constituents is still uncertain, these conditions would be fulfilled by the assumption of the presence of a slightly soluble surface-active component in the original oil. This component would migrate to a freshly formed interface because it would thereby lower the free energy of the system. The component at the surface constitutes an expanded monolayer which would become compressed, upon retraction of drop, due to the slow rate of re-solution of the film components into the bulk of the oil. It is possible, by involved extraction processes, to separate or at least concentrate this film-forming fraction. However, using the assumptions made above, the technique of monolayer film study may be applied to reveal much of the nature of the adsorbing material without resorting to an actual separation of the film-forming constituents.

By Frank J. Markewicz, William Lodding

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite by the mineralogist. The word glauconite is from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was dug and marketed as a fertilizer and soil conditioner for more than 100 years. The advent of prepared fertilizers with adjustable nutrient ratios led to the decline of green- sand for agricultural application. The material has since been recognized for use in water treatment. Unfortunately, in spite of large reserves and worldwide distribution, the mineral has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This lack is probably due to a paucity of research on its potential commercial application. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and generally low potash content (up to 8%), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of up to 100 tons per acre were sometimes made, although recommendations for agricultural use suggested 20 to 50 tons per acre (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as "poison," "burning," or "black marls." The availability of higher-grade potash salts from other mineral sources, and the manufacture of prepared fertilizers, displaced the agricultural use of green- sand during the later 1800s. During the mid-1800s the domestic greensand industry, centered in a small section of the eastern United States, grossed more than $500,000 per year. Toward the end of the century, annual production had dwindled to less than $100,000. By 1910 there were only six or eight greensand producers, grossing less than $5000 (Tyler, 1934). There was a small revival in the industry during World War I because of the curtailment of foreign potash, especially from Germany. During the later 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace- element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base-exchange properties would release trace elements. For a short time glauconite was utilized in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s for making green glass (Cook, 1868). In the early 1900s the base-exchange property of glauconite was recognized for water treatment, and the mineral gained acceptance as a water softener. Mansfield ( 1922) does not mention base-exchange; however, the base ex-

Jan 1, 1975

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

By Brian Mason

Wire Ropes in Mines. Proceedings of a conference held at Ashorne Hill, Leamington Spa, Warwickshire, September, 1950. Published by the Institution of Mining and Metallurgy, Salisbury House, London, 1951. 828 P. $7.00-The volume contains 18 pages on the manufacture and properties of rope wire and wire ropes. In addition, wire rope practice in Britain, Ontario, the Witwatersrand, The United States, South Africa, and other countries are discussed. Testing, government regulations, and inspection are also treated. The book contains a three day discussion on these subjects complete with a summary of conclusions and recommendations. Heating Ventilating Air Conditioning Guide 1952. Published by the American Society of Heating and Ventilating Engineers, New York, 1952. 1496 P. $7.50.Contains a technical data section of reference material on the design and specification of heating, ventilating and air conditioning systems. Also has a section containing information on equipment and manufacturers. An index to technical and equipment sections is included.

Jan 1, 1952

J. H. HEGINBOTHAM, a, metallurgist of the General Engineering Co., talked on "Current Milling Practice at Kirkland Lake," at the December meeting of the Utah Section. The ore is enough alike through the whole district so that some generalizations and comparisons may be made. The question as to whether or not the flotation process should be used in the flowsheet for extracting gold by cyanide solutions is still being vigorously debated, and it will seemingly need some years for a definite answer to be given. Most of the gold is either free, though much of it is finely dispersed in quartz, or occurs with pyrite. At times there may be 2 per cent of telluride compounds in the ore, but the amount of gold telluride present is small and has not been definitely established. It has been shown by Dr. Haultain and others that though gold tellurides may be so finely disseminated that it is necessary to grind the ore exceedingly fine, the compounds themselves are not difficultly soluble. (An increase in temperature helps to dissolve tellurides, and also to settle pulps.) It is likely that if the ore were ground through 400 mesh, practically all of the gold would be soluble. As it is, with 96 to 98 per cent of the ore ground to minus 200 mesh, and some 70 per cent minus 325, the cost of

Jan 1, 1934