Search Documents

By C. V. Millikan, C. V. Sidwell

There is nothing more important in petroleum engineering than a definite knowledge of the pressure at the bottom of an oil well at any existing operating condition, and the relation of this pressure to the pressure within the producing formation. A knowledge of bottom-hole pressures is fundamental in determining the most efficient methods of recovery and the most efficient lifting procedure, yet there is less information about these pressures than about any other part of the general problem of producing oil. Determination of Bottom-hole Pressures Bottom-hole pressure may be calculated or determined by several methods. On an inactive well it may be calculated from the fluid head or, if the well is shut in, by adding the casinghead pressure, the static head of the gas and the fluid head. In wells flowing naturally through tubing the pressure at the bottom of the tubing may be calculated by adding the pressure at the casinghead between the tubing and the casing and the pressure due to the weight of the column of gas, but there is always possibility of error caused by fluid being in the annular space above the bottom of the tubing. If a well with tubing is flowing through either the annular space or the tubing, sufficient gas may be injected through the static space to insure that it is free of fluid but not sufficient to establish an appreciable friction loss. The pressure at the bottom of the tubing can then be calculated by adding to the pressure at the tubing head the pressure due to the weight of the column of gas. This is probably the most accurate method of calculating bottom-hole pressures. In wells flowing by gas-lift, the pressure at the point the gas enters the flow may be calculated by a gas-flow formula. Several types of pressure bombs have been used to measure the pressure at the bottom of wells. One is a piece of steel tubing with a check valve in the bottom and a connection for a pressure gage at the top. It is lowered into the well to the point at which the pressure is

Jan 1, 1931

By Lawrence W. Aldrich

At the San Francisco meeting of the Institute last year, I presented, through the courtesy of Dr. James Douglas, some results of experiments on the roasting and leaching of concentrator tailings. After it became apparent that flotation rather than leaching was clearly the better method of handling the particular problem under consideration, before dismantling the experimental equipment, some data were secured on roasting and leaching the concentrate itself in competition with smelting. Some of the results obtained are given in the following paper and they are of particular interest at this time in view of the large quantities of flotation concentrates with their somewhat difficult smelting characteristics now being produced. A complete wet processt consists of roasting and leaching the calcines in dilute sulphuric acid produced from the roaster gases, roasting the residue with salt and leaching with dilute tower liquors (the well-known Longmaid-Henderson process) and recovering the copper, silver and gold by cementation or electrolysis or a combination of both. It is evident, however, that the residue from the first leaching, carrying about 20 per cent. of the copper and all of the silver and gold, can be smelted if preferable. In considering the application of the scheme to individual cases, it must be remembered that freight plays a large part in any reduction process wherein smelting is not conducted at the mouth of the mine, and that it is not practicable today to build small smelting plants for individual operations, The experiments may be grouped under four main heads: Roasting, leaching, chloridizing residue, and recovery of copper from solutions. The products of two concentrators were used: The Nacozari concentrates were the product of a large modern mill not using flotation, the copper mineral being largely chalcopyrite; and the Tyrone concentrates, the product of an experimental mill including flotation, the copper mineral being chiefly chalcocite. Typical analyses are given in Table 1. Fig. 1 shows screen analyses of calcines obtained by dead roasting the

Jan 1, 1917

By J. P. Denny

The constitution of the Ga-In system was determined by thermal methods. An experimentally determined metastable equilibrium line (an extension of the indium-rich liquidus) was obtained. The various alloys were studied metallographically using polished samples obtained by a casting method. These low melting alloys required a special dry-ice assembly to maintain a suitable temperature. RECENT interest in alloys that are liquid at room temperature has led to rather extensive investigation of gallium-base alloys. Widely distributed over the earth, gallium could be produced in substantially larger quantities than at present, if a significant demand existed.' One study' has established its presence in 12 out of 14 zinc blends, in all of 15 aluminum ores, in 4 out of 12 manganese ores, in 35 out of 91 iron ores, and in all of 7 magnetite ores. It occurs as a rule in minute amounts, however, leading to high extraction costs. Recent quotations run from $2.50 to $7.50 per g. During the course of the present investigation, portions of the system Ga-In have been redeter-mined, and the results of this study are presented herein. Thermal and metallographic methods have been employed. Lecoq de Boisbaudran, the discoverer of gallium, conducted the first investigation" on Ga-In alloys in 1885. The temperatures of incipient melting, and of completion of melting, were determined at four alloy compositions. In 1936, Hansen' constructed a eutec-tic-type phase diagram for the system Ga-In, based on . work. The existence of a Ga-In compound was regarded as improbable by Hansen, and subsequent investigations are in agreement. French, Saunders, and Ingle3 conducted a more complete study of the system in 1938, using thermal methods. Their phase diagram is a eutectic type, containing a unique concave-upward liquidus. The solid-solution range of gallium in indium was reported as 9.5 pct by weight, and that of indium as less than 1 pct, at the eutectic temperature. The eutectic composition, determined as being bracketed by the compositions showing a true horizontal at the eutectic temperature (16°C), was reported as 76 5-0.5 pct Ga and 24 i 0.5 pct In. Experimental Procedure The preparation of Ga-In alloys is simplified by the low melting points involved. Various compositions were prepared by melting in pyrex tubes, using a cover of distilled water or parafin to prevent the alloys from wetting the glass wall. In all cases, the melts were homogenized. by stirring. Where possible, both cooling and melting curves were determined. The extensive undercooling of gallium was found to prohibit a satisfactory cooling-curve analysis of gallium-rich alloys, however, and transition points on the gallium side of the eutectic could be determined only by melting curves. The inverse rate method of thermal analysis proved to be most satisfactory and was used to a great extent. Various heating and cooling rates were used, ranging from 0.2" to 5.0°C per min. Low temperature melting analyses were conducted within a constant temperature bath, maintained at about 70 °C. The alloys were solidified (under water or paraffin) within a pyrex tube, using dry ice; the tube was then sealed within a cold Dewar flask, the unit transferred into the constant temperature bath, and periodic temperature readings taken. The high temperature melting-curve determinations and all cooling-curve determinations were made in a vertical tube furnace. At near-eutectic compositions, the furnace was placed within a refrigerated room held at —20°C. Accordingly, the furnace on cooling approached —20°C asymptotically and permitted the determination of those phase transitions occurring below room temperatures. Temperatures were measured with a 30-gage iron-constantan thermocouple, immersed directly in the alloy. To prevent contamination of the melt, the leads and junction were coated with Lucite, applied by painting with a solution of Lucite in ethylene dichloride. Electromotive force measurements were made with a Leeds and Northrup precision potentiometer, type 8662. The couples were calibrated against the boiling point. of water and, at lower temperatures, against a calorimeter thermometer having a Bureau of Standards certificate. The melting points of gallium and indium used in the present investigation were determined as 29.-77° and 156.1°C, in good agreement with previously reported values of 29.78°C° and 156.4"C.' The spec-

Jan 1, 1953

By Albert J. McIntosh

In discussing the petroleum products situation the first thing that comes to mind is "what is happening to gasoline." Is the consumption increasing? How is the export market? What about imports? Are stocks on hand too high? Have we produced too much? This paper will attempt to answer these questions. Consumption of gasoline (motor fuel) in the United States in spite of the depression and the chaotic conditions of many industries has increased during 1931 about 2 per cent over 1930. This favorable factor was offset by a severe contraction in exports, which fell off about 30 per cent from 1930. This drop in exports was so large that very little more export business was done than in 1926 or 1927. Taking all demand combined, there was a decrease from the peak year of 1930 of nearly 11,000,000 bbl., amounting to slightly over 2 per cent. The units of the industry, though, should have expected some decrease and governed themselves accordingly. Let us see what they did. They reduced imports over 3,000,000 bbl., which helped. Production was cut 3,000,000 bbl., but this was not enough, so that stocks increased 1,800,000 bbl. whereas during the previous year stocks were reduced 2,500,000 bbl. It is apparent, therefore, that something was done to keep the industry in balance in regard to gasoline, but not enough. If the year had ended on Sept. 30, we could have said that production had been cut 19,000,000 bbl. and stocks had been reduced from the previous year, but the excessive production during the last three months of the year changed everything. It is a strange thing and worthy of note that the price of gasoline fell to its lowest levels when apparently the greatest improvement was being made, and that during the last quarter of the year prices started to improve, when, in spite of an improvement in total demand which approximated 1930, an excessive production caused an uneconomic condition to set in. Stocks on hand on Dec. 31 were unquestionably too high, possibly 10,000,000 bbl. more than was needed for a strong condition to obtain. It seems almost unbelievable that the industry would continue to produce

Jan 1, 1932

By R. S. McCaffery, D. E. Krause

There has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this tuyere, the arlicle states, resulted in a decrease of blast pressure of about 4 Ib. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 Ib. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

By C. E. Birchenall, R. H. Condit, M. J. Brabers

In the oxidation of pure iron above 700°C the overall rate is determined mainly by the rapid growth of wiistite, through which iron ions can diffuse rapidly.' Nickel added to the iron progressively decreases the stable range of composition of wustite.' When enough nickel is added to eliminate wiistite as a stable phase, the spinel is the fast growing phase. This investigation was undertaken to test the hypothesis that nickel substituting for iron in magnetite might decrease the rate of spinel growth by reducing the iron mobility. Nickel ferrite boules grown by the flame fusion process were purchased from the Linde Co. Chemical analysis gave an atomic ratio of iron to nickel of 2.88 and showed no other cations. They were cut into discs and ground to give flat, parallel faces. The experimental procedure employed was like that of Eisen and Birchenall in which the distribution of radioactivity diffused in from a vapor deposited surface layer was determined by counting the residual activity through a series of ground faces. The diffusivities were calculated in a manner consistent with the requirements discussed by Condit and BirchenallP The details will be given in connection with a more extensive spinel diffusion study now in progress. The results of the measurements are shown in the figure in comparison with earlier data on magnetite1 and zinc ferrite. The uncertainties arising from scatter in the activity vs distance relationship and uncertainties in the temperatures are shown by flags. Despite the scatter it is clear that substitution of a considerable part of the iron in magnetite by nickel, in this case about one third decreases the iron mobility substantially. sachs' determination of the distribution of iron and nickel in scales on iron-nickel alloys appears to show that nickel is less mobile than iron in the spinel layer. It is evident, therefore, that nickel plays several roles in reducing the oxidation rate of iron-nickel alloys. 1) It reduces progressively the stability range of wiistite. ' 2) It reduces progressively the stability range of the iron-nickel spinel phase in terms of the variation in cation to anion ratio.' 3) As shown in this investigation, it reduces the cation mobility in the spinel phase which is the faster growing phase in the absence of wiistite. The fe was obtained from the Oak Ridge National Laboratory. The research was supported by the Air Force Office of Scientific Research (ARDC) under contract number AF 18(600)-967.

Jan 1, 1961

By Joseph Pogue

IT is well known that one of the cornerstones of economic theory is the so-called law of supply and demand, which, really, is a group of economic laws, one of which may be succinctly stated A rise in price tends, sooner or later, to increase supply. It is the fear that, in the case of petroleum, a limited' natural resource, a point will soon be reached when supply will not respond adequately to price advances, which in recent years has prompted a movement for oil conservation. This movement has lately taken concrete shape in the appointment of 'a Federal Oil Conservation Board by the President. An important aspect of the law of supply and demand is that the supply of any commodity, is not an entity per se, but is a factor of price. Supply, without the specification of, price, has no exact meaning; and, in practice supply cannot be divorced from considerations of price. Mathematically, supply may be expressed by the formula SP, which means that supply varies with price, just as the value of 10 raised to the x power varies with x. In its technical usage, supply is the, quantity of a commodity that is bought currently on the market at a given price. In the case of a natural resource, however, this quantity will eventually depend not alone on price but on the physical volume of the reserve that exists and that, in consequence, can respond to the stimulus of price. If this reserve is fixed in size, we must sooner or later reach a point where supply can no longer respond to price in the usual degree and a permanent shortage will develop which no advance in price can correct, except in so far as higher prices may curtail demand or improve the efficiency of utilization. This statement brings us to the examination of amore fundamental aspect of the law of supply and demand as applied to natural resources; namely, that natural-resource reserves are not fixed in size: just as the current supply of a natural-resource commodity is a function of price, so its reserve is likewise a resultant of price. Natural-resource reserves; therefore, have no exact meaning without the specification of price, and in practice their measurement. cannot be divorced from considerations of

Jan 3, 1925

By J. A. Fulton, A. B. Foote

Gold was discovered in the Sierra Nevada by J. W. Marshall on Jan. 2, 1848. The town of Grass Valley soon sprang up and contained several stores in 1849; but the population of the town has always reflected the fluctuations in quartz mining. Gold-bearing quartz was found on Gold Hill in September 1850, and in the next two years most of the quartz-bearing veins in the vicinity were located. At first, the quartz was crushed in mortars with spring poles; the IIuff Co. took out $20,000 in this manner during the winter and spring of 1851. The first mill was put up in January, 1851. In 1866, there were in Grass Valley 248 stamps, crushing 71,420 tons of ore with an average yield of $30 to $35; in Nevada City, there were 142 stamps, crushing 14,200 tons, with an average value of $25. Rut in 1918, only two properties in this region, the Empire and the Korth Star, were producing Since then, there has been a revival of mining in the district and the following properties are being opened up: The Golden Center. Grass Valley Gold Mines Co.. Idaho-Maryland Mines Co., while the Su1tana is kept unmatered and work is going on in a half dozen mall propertics Mining Claims At the first meeting of miners in Grass Valley, Jan. 13. 1851, a plot :30 by 40 ft. was allowed for a claim, the boundaries in all cases being perpendicular. In 1852, the quartz miners in Nevada County deeided that "each prospector shall hereafter be entitled to 100 ft. on a quartz ledge or vein and the discoverer shall be allowed 100 ft. additional. Fach claim shall include all the dips, angles, and variations of the vcin." This rule was in force until replaced by the Federal mining laws of 1872; these allowed quartz claims to be 1500 ft along the vein, with all the dips, spurs, and angles, and to have a width of 600 ft. The holdings of the principal companies consist of these early patented mining claims; standard claims, as authorized by the Act of 1872, both patented and unpatented; agricultural tracts, both patented and

Jan 1, 1927

By Duncan MacVichie

The iron fields described here are located in the Iron Springs and Pinto mining districts, Iron County, Utah. This region is in southwestern Utah, about 260 miles south from Salt Lake City, and is reached by the Los Angeles & Salt Lake railroad of the Union Pacific system. The iron fields lie at an elevation of 5500 to 7500 ft. above sea level, and are essentially desert in character. They are covered with a light growth of sage brush, piñon pine, and scattered cedar. Weather conditions are unusually favorable for all-year mining operations, the winters being mild with little or no snow; and the summers not excessively hot, the temperature rarely rising to 100 during the day, while the nights are invariably cool. The iron-ore bearing area extends from the Iron Springs district to the Iron Mountain mining district, being approximately 25 miles long in a northeast-southwest direction, and from 1 to 3 miles wide in a northwest-southeast direction. In the Iron Springs and Pinto mining districts, the ore occurs at various points around three sides of Granite Mountain and Iron Mountain. This is readily understood by reference to Figs. 1-4. These mountains are composed of andesite, which has been forced up through the surrounding sedimentary formation, in the form of laccoliths. An extensive report on the geology of these districts was made by Leith and Harder,' who state: The three dominating geological features of the district are three large andesite laccoliths which constitute the Three Peaks, Granite Mountain, and Iron Mountain; lying in a northeast-southwest line across the area in question. Three unconformable sedimentary series, aggregating 4000 ft. in thickness, outcrop in successive rings around these laccoliths, dipping outward asymmetrically, very steeply at the contact, less steeply farther away. Still farther from the laccoliths, lava-flows 2000 ft. thick rest in nearly horizontal attitudes on the tilted sedimentary rocks. These general relations are modified by faulting. All of the rock formations of the district are more or less covered on the middle and lower slopes by unconsolidated and partly consolidated erosion debris, both aqueous and subaerial, which spreads out on the lower ground to make the deserts.

Jan 1, 1927

Geostatistics originated as an application of a classical statistical concept, multivariate linear regression, to the solution of a practical problem, estimation of reserves in the South African gold mines. In this respect, geostatistics should only be considered as one statistical method among many that can be used to evaluate mineral deposits. R.F. Shurtz has studied possible applications of power spectrum analysis to the same problem, and these studies may result in future improvements over the presently accepted geostatistical methodology. The intention of R.F. Shurtz's paper, as stated by the author, is to "relate geostatistical doctrine to classical statistical and mathematical concepts." However, in this comparison the "geostatistical doctrine" appears to include only the simplest among the geostatistical concepts advocated by G. Matheron, while "classical statistical and mathematical concepts" are limited nearly exclusively to power spectrum analysis. The author attempts to compare the two methods, and to prove the theoretical superiority of power spectrum analysis. Unfortunately, a number of errors and incorrect statements are made concerning both the theory and application of geostatistics, which invalidate the comparison and the conclusions drawn from it. The errors made in this comparison are understandable since few scientists can claim to have expertise in two theories as diverse as those compared here. In many respects, this paper is reminiscent of polemics which occurred 15 to 20 years ago when geostatistics and trend surface analysis were compared. Each method has its own merit and limitations, and none can claim absolute superiority. The most misleading statements found in R.F. Shurtz's paper are: The definition of the semivariogram given on page 1923 is incorrect. If the maximum difference between two assays is 1, the maximum value of the semivariogram is not 1, as stated, but 0.5. The comparison of geostatistics and linear regression made in the section entitled "Insufficiency of Classical Statistics?" is not valid. The semivariogram of the sample values given in Table 1 (page 1919) has a parabolic shape indicative of a linear drift. When such a semivariogram is observed, the simplest method of geostatistical estimation (linear kriging with unknown mean) is not applicable. Universal kriging must be used that takes trends into account. On page 1921 it is stated that the use of trends "is officially disparaged in geostatistics." Again on page 1924 mention is made to "Matheron's commitment to random process (intrinsic) models and his present categorical rejection of deterministic (trend) models for mineral deposit evaluation." Indeed, from articles published by geostatisticians in the 1960s one could infer that geostatistical methods are not compatible with the presence of trends. However, even the simplest

Jan 1, 1984

By A. D. Smigelskas, E. O. Kirkendall

THIS is the third paper in a series on the diffusion of zinc in alpha brass.1 At the time of the first-paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; however, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. PROCEDURE A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about ¾ in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 ± .0002 in. (1.0625 ± 0.0005 cm.) thick. Six 0.005-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in copper and alpha brass, were stretched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every ½ in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1946

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

By William S. Hannan, H. Rush Spedden

FLOTATION may be defined as a process whereby mineral particles are concentrated by selective adhesion to air-liquid interfaces. The process involves attachment of desired mineral particles to air bubbles, and removal of the mineralized air bubbles from the surface of the pulp as a mineral concentrate. PROBLEM Although great strides have been made in understanding the principles of flotation, one part of the process which has not been adequately explained is the mechanism by which selected mineral particles become attached to air bubbles. A glance at the froth of an operating flotation cell demonstrates adequately that use of proper reagents and conditions will result in such attachments; but how such attachment takes place is not definitely known. A better knowledge of this factor might lead to improved flotation practice either through altered machine design or the application of scientific innovations. Direct observation of the behavior of mineral particles and bubbles in an operating cell does not appear promising because of the complexity of the system. For this reason, conclusions concerning the problem must be deduced from theoretical considerations or from observation of simplified systems designed to reproduce conditions thought to exist in an operating cell. PRESENT THEORIES Two mechanisms have been recognized as fundamental in particle-bubble attachment: gas precipitation and direct encounter. It is a simple matter to demonstrate in the laboratory that attachment can be brought about by either mechanism. As to the relative importance of the two in a particular flotation system, however, there is a divergence of views. Taggart1 states, Under exceptional circumstances sufficient force and time to effect attachment may conjoin in an ore pulp undergoing agitation, and a preformed bubble adhere to a collector-coated mineral particle, but the occurrence is rare. . . . Pulp-body froth flotation effects selection in the body of a conditioned pulp by causing gas bubbles to precipitate from solution in the liquid phase preferentially at the surfaces of collector-coated particles, and to cling to these particles. Gaudin2 states that, within the pulp body of an agitation machine, attachment of mineral particles to air bubbles occurs as a consequence of contact between the two. This theory has been supported by theoretical reasoning and much circumstantial evidence. Perhaps the most interesting bit of evidence in favor of this theory is the difficulty in the flotation of fines. If attach-

Jan 1, 1947

By E. O. Bennett

When oil is takcn from a subsurface structure it is generally accompanied by gas. The gas thus produced represents the 1ighter hydrocarbons present in the original petroleurn accurnulation, which arc, insoluble at the reduced pressures created around a well when it is producing. In some cases the gas accompanying the oil may come from a gas-bearing stratum not in immediate contact with the oil. The amount of gas from the formation accompanying each barrel of oil is called the natural gas factor. Energy Causing Well to Flow The force causing the flow of fluid into a well when it is drilled into an oil-bearing structure is the pressure differential between the well bore and the formation. A pressure differential between the formation and the well may be set up in three different ways, as follows: (1) pressure due to gas in solution or in contact with the oil, (2) hydrostatic pressure due to water in contact with the oil (it may be either bottom or edge water); (3) pressure difference due to forcc of gravity. The greatest source of energy for producing oil from most oil fields, and the one over which the greatest control can be exerted, is the poten-tial energy in the gas under pressure in the formation. In any pool there is but a definite amount of gas available. Part of this gas may be in solution and a part in contact with oil. The amount of gas in solution in each bard of oil depends on the pressure and temperature in the formation and the characteristics of the oil. Whether the gas is in solution or in contact with the oil it is necessary to use the energy it, contains as efficiently as possible in order to obtain the greatest ultimate recovery from the pool. Bush1 states: Gas being the most efficient aid in moving the oil, it is important to prevent more of it from escaping than is necessary to remove the maximum amount of oil from the sands. The conservation of this energy is far more important to the producer of oil than his returns from sales of gas to distributing companies. The flowing life of the well is the most profitable period, and keeping the gas-oil ratio low, or keeping the

Jan 1, 1928

By John H. Melvin

THE Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. GEOLOGY Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its uncemented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable - slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1947

By John H. Melvin

The Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. Geology Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its unce-mented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1949

By Rizo-Pairón Alfonso, A. M. Gaudin

PREVIOUS studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector The results obtained indicate that a I I ratio of collector ion to activator ion gives optimum results, and that a 2 I ratio almost fails to achieve activation and flotation Yet, a 2 I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids, they confirm that an adsorbed coating is inescapable APPARATUS AND SUPPLIES The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz The flotation machine was built according to the design of D W McGlashan It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel stator, as in the Fagergren laboratory machine The air intake is controlled by a valve, and the cell consists of a beaker The quartz was obtained from vein quartz stored in large chunks It was first crushed to 20 mesh, then sized on a 28-mesh screen The 20 to 28-mesh size alone was retained for use This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used The barium was used as barium chloride, Baker's analyzed C P The oleate was used as sodium oleate It was prepared from sodium hydroxide, Baker's analyzed C P , and oleic acid purified by R R de Arellano3 in the laboratories at the Massachusetts Institute of Technology The purification procedure was elaborated from the recent researches of Brown and Shinowara 2 It consisted in (I) saponification of olive oil with potassium

Jan 1, 1942

By Gerald Edmunds

In a paper1 before this Institute in 1940, the writer reported that the surface orientation texture of zinc and cadmium differed from the texture existing within the casting, in that basal planes were parallel to the surface. He was unable to rationalize the , origin of this surface texture. It is conceivable that the surface orientation texture is influenced by the atomic force fields, which are different at the surface and within the body of metal. It was considered that a radical changc in the surface against which the metal is cast might alter the surface texture. In trial of this, zinc has been cast against a surface of molten lead, but the same result has been obtained—i.e., (001) parallel, ± 2oo, to the surface—as was obtained when it was cast against air, Transite or iron.' Into the bottom of an open cast-iron tray, 7 by 14 in. by 2 in. deep, preheated to about 275°C., about 1/4 in. of lead, then 1/2 in. of zinc was poured, and the whole was covered with an electric heater to enforce freezing from the bottom upward. After a lapse of time sufficient for the zinc but not the lead to solidify, the zinc slab was raised free of the molten lead. The bottom surface of the zinc casting was coated with a thin layer of lead. A specimen of the slab 136 in. square was metallographically polished to flatten it and remove the slight film of lead, and the orientation was determined by the method used before,' with the result stated above. Some determinations have also been made on other metals, as follows: Surface orientation determinations were made on the 3/8-in. diameter grip section of two 1/4-in. diameter aluminum-alloy die-cast tensile bars and on a 1/8 by 1/2-in. flat aluminum-alloy die-cast tensile bar. None of these three aluminum die castings exhibited any preferred orientation at the surface. A brass die casting (nominal composition: 60 Cu, 37.75 Zn, 1.00 Sn, 1.00 Pb, 0.10 Al, 0.15 Si) furnished by C. S. Smith was also examined. The surface showed a random orientation of alpha and beta. Summary A zinc casting solidified against a molten lead surface was found to have the same surface orientation texture, (001) parallel to the surface, as other zinc and cadmium castings. Aluminum and alpha-beta brass die castings were found to have random grain orientation textures at the surface. Acknowledgment The X-ray determinations were conducted by M. L. Fuller.

Jan 1, 1945

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By R. Schuhmann

As a response to rapidly growing specialization in various branches of metallurgy, it is proposed that undergraduate education in metallurgical engineering should be built up around four principal scientific themes: 1—thermodynamics, 2—structure, 3—mechanics, and 4-—rate processes. THE following quotation from a recent article by von Bertalanffyl describes very well the situation which today challenges curriculum designers in all branches of science and engineering: "Modern scientific education is presented with a well known dilemma. The amount of facts in modern science, and in any of its smallest branches, is enormous. Life in general, and the academic curriculum in particular, is short. The abundance of factual data, as well as the intricacy of modern scientific techniques, experimental and theoretical, necessitates utmost specialization. This specialization, unavoidable though it is, involves serious danger for both the education of the scientist and the social function of science. "In so far as the advancement of science is concerned, history shows that interconnection of different fields and problems is a most important basis of progress. Many of the paramount achievements of science arose on borderlines, and from the synthesis of formerly separate fields . . ." Specialization in subfields of metallurgy has become a serious educational problem only in about the last decade. The growth in specialization, almost as a necessity, has paralleled the rapid growth in metallurgical knowledge during this period. Moreover, in planning future educational policies, the educator must be concerned not only with the rate of increase in metallurgical knowledge and with the concomitant rate of increase in specialization, but also with the second derivatives, that is, with the rates of increase of the rates of increase. These second derivatives are positive and large; the growths being dealt with are self-catalyzing, or like a chain reaction. As a measure of specialization, the length of the list of different kinds of metallurgies can be considered, the kinds of metallurgy which represent one person's particular interests and those of other practicing metallurgists. To start with, there are physical metallurgy, process metallurgy, and mineral dressing, then mechanical metallurgy, metal processing, foundry metallurgy, corrosion, solid state physics, high temperature metallurgy, welding, powder metallurgy, nuclear metallurgy, etc. Each of these fields is growing so rapidly that any one metallurgist can hope at best to keep up to date in only one or two. What is the impact of all these "metallurgies" on metallurgical education and metallurgical curricula? In answering this question, it can be said, first, that educators have resisted fairly well the temptations to split up metallurgy, with different curricula, different options, degrees with different labels, and the like—degrees are still given in plain Metallurgy and Metallurgical Engineering. In other ways, though, the pressures of specialization have had noticeable effects. There is a tendency to think of these "metallurgies" as the important subdivisions of Metallurgical Engineering and to work up

Jan 1, 1956