Search Documents

By N. B. Aughenbaugh, W. C. Patrick

The availability of a thorough, simple-to-use roof fall classification system is desirable for several reasons. First, such a system would expedite the reporting of falls for the purposes of estimating material removal costs, analyzing damage levels, and complying with federal regulations to report falls in certain areas of the mine. Second, the classification system would allow the mining engineer to record falls routinely with little time and effort expended. This would encourage him to make observations concerning what type of roof support would work best in a given situation. Third, and probably most important, an

Jan 3, 1979

By L. W. Bahney

Frequently in using a thermo-electric pyrorneter for measuring the temperature of a furnace, a hole is drilled at the back or side of the furnace, through which is introduced the tube containing the thermo-couple. At times the couple is left almost where it drops, for the reason that it soon becomes too hot to be handled easily, and the space at the back or side of the furnace may be so small and uncomfortably hot that an easy and accurate adjustment is nearly impossible. In order to overcome this clumsy and unscientific method of using the thermo-electric pyrorneter, I designed an adjustable stand, to hold the clay or quartz tube inclosing the platinum and platinum-rhodium leads that constitute the couple of the Le Chate-lier thermo-electric pyrometer. This stand also allows an easy and rapid adjustment of position to varying heights and angles, as may be desired for special reading, This stand is illustrated in Fig. 1. The couple in the tube might be of better service if the tube were held a little higher above the charge in a roasting-dish, changing the height and angle if desired. The stand, made of 1.5-in. water-pipe and mounted on casters, is heavy enough so it cannot be tipped over easily. It is adjusted to any position, and has a universal clamp which holds the clay or quartz protecting-tube. To avoid disturbing the wires of the couple at the cold junction each time the tube is moved, the cooling-bottle sets in a wire basket so placed that it moves forward or back with the couple. To overcome the necessity of leveling and adjusting a galvanometer at each furnace, a switch-board is used to connect

Jan 1, 1910

By Stanislaus Skowronski

THE melting of cathode copper, usually containing 99.98+ per cent. Cu, would appear to be a simple matter. Owing to the well known affinity of copper for sulphur, however, so much sulphur is absorbed by the copper during the operation that a long and expensive refining process is required to remove it, and the final product is inferior in purity and lower in electrical conductivity than the original cathode copper. The furnace operation, as now conducted, includes the following stages: 1. Charging the cathodes into the furnace. 2. Melting the cathodes. 3. Oxidizing period-saturating the copper with cuprous sub-oxide and bringing the metal to the condition known as "set copper;" this is now done by blowing air into the molten bath of metal. 4. Reduction period, otherwise known as "poling," whereby the oxygen previously added is removed by covering the molten bath completely with coke or charcoal and introducing large poles of green wood; this reduces the cuprous sub-oxide, bringing the copper to the "tough pitch" stage ready for casting. 5. Casting Period. Many experiments have been made to obviate the long periods of oxidation and subsequent reduction, with no success. While the copper first, cast will be good, as indicated by the set surface of the bars, it is impossible to hold it to the "tough pitch" condition, and long before the whole charge has been poured the copper will become "overpoled," entailing numerous difficulties. Sulphur has always been blamed by the furnace men as the reason why this refining process is necessary, yet the literature on the subject does not sufficiently emphasize how small a proportion of sulphur will ruin copper for practical purposes.

Jan 3, 1918

By Yap Chu-Phay

IN the previous paper, the writer showed how, on the basis of thermodynamic reasoning, it seems probable that when true equilibrium conditions obtain, carbon exists as Fe3C in the liquid state and as elementary carbon in the solid state (7 Fe), in which case the solidus would be a straight line from 0.18 to 1.70 per cent. carbon (Fig. 1). In the same paper he concluded that the solidus obtained by Honda 'and his co-workers1 probably does not represent the same conditions, insuring a complete equilibrium. Except for a downward temperature displacement, the solidus obtained by Gutowsky,2 using the Heycock and Neville method, practically coincides with Honda's solidus as shown in Fig. 1. The writer at first thought that perhaps in some way Gutowsky's thermocouple was improperly calibrated for high-temperature measurements, as his liquidus was also much lower than those obtained by Carpenter and Keeling3 and by Ruer and Goerens.4 However, the eutectic temperature obtained by Gutowsky agrees with the generally accepted value of 1130° C., so that the validity of the inference regarding improper temperature calibrations is to be strongly doubted. In Fig. 1, Gutowsky's solidus is shown both in the original and in the corrected form. In the latter, a correction of 29.2° C. is made for all temperatures above 1416° C. in accordance with-

Jan 1, 1931

By R. E. Mazurak, E. L. Ealy

At the Beckley mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by wing a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1983

By K. A. Grace

Reserves are the basic foundation of any mining enterprise, but a lack of understanding of the concept of resources and reserves is still a frequent cause of failure in mining ventures. A review of the development of the resource-reserve concept emphasizes the necessity for a common language, and the classification system as set out by the US Geological Survey and Bureau of Mines is advocated as the basis for this. Because of its strong economic connotation, the term reserves should be severely restricted in its use, and should encompass mining and processing factors. Modifications to the basic definition of reserves to accomplish this are proposed. Caution must be used in the quantification of undiscovered or hypothetical resources, particularly in juxtaposition with known resources data.

Jan 1, 1985

By Alfred E. Hunt

In a paper written for the Boston meeting of February, 1888 (Trans., xvi., 693), on "Some Recent Improvements in OpenHearth Steel Practice," the writer described the reducing agent used by the Carbon Iron Company as "a peculiar graphite from Cranston, near Providence, R. I." Upon an application pending at that time, a patent has since been issued as number 259,795, to Mr. Matthew Graff, for the use of solid carbonaceous matter in the form of coke, charcoal, gas carbon, bituminous or anthracite coal, ground to the size of coarse sand and then coated with a mash of lime, magnesia, clay, or other material of a like character, as an agent to reduce metallic oxides. An amount of this prepared carbonaceous matter equal to from 25 to 30 per cent. of the weight of the ore treated is required to perform the complete reduction. The idea is that the carbonaceous matter is protected against rapid combustion by a suitable coating of some inert material, so that, in effect, its action as a reducing agent will be similar to that of the Cranston graphite previously used, allowing the solid carbon to remain without combustion in intimate mixture with the iron oxide at a temperature sufficiently high to reduce the ore and in some cases to melt the matrix in which the iron is held. In the present practice of the Carbon Iron Company, the use of graphite, except for the formation of bottoms of the reverberatory furnaces in which the reduction is performed, has been entirely abandoned, and " retarded coke," as it is called at the works, has taken its place. Five hundred and fifty pounds of Connellsville coke is ground in a pan to 16-mesh fineness, or is taken in the form of ordinary coke-dust, and made into a hollow basin on the mixingfloor ; and seven bucketfuls of a wash composed of equal parts of lime and fire-clay, mixed in water to the consistency of thin cream,

Jan 1, 1889

By G. W. Powell

ACCORDING to crank,' the accumulation equations for inter diffusion in a binary system whose molal volume is a function of concentration are

Jan 1, 1965

By J. A. Herbst, D. W. Fuerstenau

The effect of mill speed and ball load on the dry ball milling of dolomite is examined in the context of the batch grinding model. Observed changes in the parameters of the model are interpreted, as far as possible, in terms of the mechanics of particle motion in the mill. A parameter estimation scheme previously proposed by the authors is shown to provide the basis for a successful simulation of grinding behavior over a wide range of mill speeds and ball loads. Finally, a combination of experimental and simulated results is used to determine the optimum mill speedball load for closed circuit grinding in this mill-material system.

Jan 1, 1973

By Lawrence Adler

The authors are to be complimented on using a novel and potentially helpful technique to analyze the effects of mine roof trusses. However, some criticisms of their application and analysis seem appropriate to further its acceptance. This discussion will deal with the normal structural analysis format covering: 1) material. 2) load, 3) structure, and 4) analysis. It will then briefly review the testing procedures and finally cover miscellaneous items. That the analytical and testing results admittedly disagreed by several orders of magnitude, indicates a need for improved understanding. The introduction of data determined previously was not assisted by references to "Interim" or "Preliminary" reports. This material should have been concisely reformulated for the open discussions that Transactions encourage. In addition, many important simplifying assumptions are tacitly made without recognition, and much less, an attempted justification.

Jan 1, 1979

By Sanford S. Cole

LABORATORY TESTS Takakuwa and Takamori' have applied the principle of phase inversion, well known in the chemistry of colloids, as a means of evaluating the wettability of minerals and to classify some frothing agents. By determining the angle of contact across the liquid phase of an emulsion, it has been possible to readily determine the wettability of a mineral. When this angle is less than 90°, the emulsion is of the oil-water type, and if it is greater than 90a, then the emulsion is of the water-oil type. The authors replaced oil with benzene in their recommended operation. They studied this method with the influence of ethyl xanthene on galena, on activated or unactivated zinc blend and of sodium cyanide on chalcopyrite and zinc blend. Raffinot and Formanek" described a pilot flotation plant with a capacity of 33 to 66 lb per hr of ore which is at the Laboratory of the Sociktk Minerais et Metaux in Paris. The plant will handle about 440 lb of ore per 8-hr shift and a regular series of tests can be undertaken with two to three tons of ore. Ore is ground to 0.1 in. and blended in advance. The plant includes two mills used either as rod mills or ball mills, conditioners, four groups of three cells for rougher circuits, eight cleaner cells and two small mills for regrinding middlings. Automatic controls for the pulp level in the cells, automatic sampling and addition of flotation reagents by electric valves facilitate plant operation and help to produce regular runs in spite of small throughputs.

Jan 8, 1963

By Joseph Jensen

FROM Aug. 31, 1937, until Apr. 30, 1939, there were 40,872,610 bbl. of oil run to storage in California; from Apr. 30, 1939, to Aug. 31 of the same year 5,512,912 bbl. were withdrawn from storage. But from Aug. 31, 1937, to Aug. 31, 1939, the number of producing wells in the state has increased from 17,706, with a potential production of 1,323,202 bbl., to 18,910, with a potential of 2,302,282 bbl. Thus, in a period of two years, during the first 20 months stocks increased over 1/3 and during the following four months stocks decreased 1/30. In the same two years the number of productive wells increased 1/15 and potential increased 3/4. Undoubtedly, the large increase in stocks created the pressure that caused the reduction in stocks that followed; yet this has come about in spite of the larger number of wells and higher potential. Cause of the change was the adoption on May 17, 1939, by the Central Committee of California Oil Producers of a uniform method of oil curtail-ment for all wells throughout the state. Acceptance of the method in the four months following adoption by practically all fields in California indicates that producers generally are convinced of its merit and fairness. True, some operators still overproduce, but the restraint practiced by the remainder of the industry has been sufficient to turn a situation headed for chaos into one of reasonable stability. Credit for this change goes to the industry itself, because it has all been accomplished under voluntary oil curtailment.

Jan 1, 1940

By E. G. Deane

A METHOD of top slicing has been devised at the Miami Copper Co.'s mine at Miami, Ariz., which differs radically in some ways from the customary methods of top slicing. The area of that section of the orebody in which top slicing is used is about 800 ft. square. The ore, while for the most part soft, is, nevertheless, considerably harder than the capping. The latter is siliceous, seldom containing any clay or other binding material, and breaks into fine particles so that it runs like sand if given the opportunity. Because of these facts, and because the ore is above the average grade of the mine ore, it has been mined by top slicing. Haulage levels are opened up 150 ft. apart, vertically, with two sublevels between at 50-ft. intervals, to facilitate the building of ore chutes. These sublevels are used during slicing for distributing air in the ventilation system. On the haulage level the drifts are spaced on 50-ft. centers, and raises along these drifts are also spaced on 50-ft. centers, except the incline raises as hereafter noted. The raises are cribbed where necessary. Where the wear will be excessive, ¼ -in. iron plates are spiked to the top of every third set of cribbing, for its protection. When top slicing was first used, an attempt was made to carry a slicing face from fifty to several hundred feet long. Timber and other, supplies were brought in through long drifts from an auxiliary shaft. Great difficulty was experienced in keeping these drifts open, the side pressure breaking the posts and the top weight breaking, both caps and posts. Furthermore, the men could not work efficiently while these drifts were .being repaired. The slicing faces advanced irregularly, due to varying conditions, and in many ways the results were not all that could be desired. It was then decided to divide the slicing area into blocks 200 ft. square and this wins later changed to 250 ft. square.

Jan 9, 1916

By William Firmstone

ON the 19th December, 1833, a patent was granted to F. W. Geisenheimer, for smelting iron ore with anthracite. In his claim he says: "Sixthly, though I cannot, and do not, claim am exclusive right of the use of heated air, for any kind of fuel, nevertheless I believe to have a right to claim the use of heated air, applied upon, and in connection with, the said principle and manner discovered by me, to smelt iron ore in blast-furnaces with anthracite coal, by applying a blast of air in such quantity, velocity, and density, or under such pressure, as the compactness, or density, and the continuity of the anthracite requires, as above amply and fully described and illustrated." Dr. Geisenheimer made experiments in smelting iron ore with anthracite at the Valley Furnace, near Pottsville, but he failed to carry out to good practical results the principles enunciated in his patent. In the Journal of the Franklin Institute for February, 1838, a communication was published that was made by Mr. George Crane, of the Yniscedwyn Iron Works, South Wales, to the British Association, in September, 1837. On the smelting of iron with anthracite coal, Mr. Crane states therein, that he began the use of an¬thracite with hot-blast on the 7th February, 1837, in a cupola blast-furnace, 41 feet high, and 10' feet across the boshes ; product, 34 to 36 tons a week. Mr. Crane goes on to say, "It may not be uninteresting to be informed in what matter the idea first occurred to me of applying a heated blast to anthracite coal. One evening, after I had placed a piece of it upon my parlor fire (which had before been made up with bituminous coal), and had allowed it to arrive at a red heat, upon applying as fierce a blast to this piece of coal as I could raise from a pair of bellows, I noticed a black spot or mark

Jan 1, 1875

By D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, Ill. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation was removed. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow readings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through wet washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main was fabricated from riveted sheets led us to discard the idea of using Pitot tubes for this service. The Venturi tube was then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made.

Jan 2, 1921

By S. F. Ramseyer, E. A. Steigerwald

INFILTRATED structures represent composite materials which are capable of combining high-temperature strength with adequate low-temperature toughness and thermal shock resistance. Although copper- and silver-infiltrated tungsten structures are actually being used in rocket nozzle hardware, adequate understanding of the fracture mechanics of these composite systems is not available. Specifically the relative importance of the strength, ductility, and modulus of the infiltrant in determining composite properties is not known to the extent that optimum composites can be selected. The major portion of experimental effort in the area of composite strength has been devoted to fiber-reinforced systems1 or to systems where a discontinuous phase is imbedded in a relatively ductile matrix.2'3 In the case of high-temperature systems, which are composed of a relatively brittle matrix, such as tungsten or an oxide, a continuous phase exists for the propagation of a crack. The method by which the presence of a conjugate ductile continuous phase influences the gross properties of the composite represents an area which requires further investigation. This technical note presents results which evaluate the effect of infiltrant strength on the strength of the tungsten-base composite. A tungsten matrix and copper-base infiltrant were selected for the initial studies because of the ease of fabrication. Tungsten structures with nominally 20 and 30 pct porosity were evaluated. The porosity was controlled by varying the initial powder size and a ratio of open-to-total porosity greater than 95 pct was obtained by selective sintering cycles. The processing sequence involved hydrostatic pressing followed by a 72-hr presinter in hydrogen at 2000° F and a final sinter at 4000°F for 4 hr in vacuum. The 20 pct porous structure was obtained

Jan 1, 1965

By Garland R. Dever, Preston McGrain, George W. Ellsworth

Abstract-Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. High calcium and high carbonate limestones suitable for use in cement and lime production, steel manufacture, environment control measures, and other special uses are present in the High Bridge Group (Ordovician) and Warsaw and Ste. Genevieve Limestones (Mississippian). Deposits with thicknesses of 7.3 to 20.7 m, (24 to 68 feet) have been documented by the analysis of samples taken at 0.3-m (1- ft) intervals. Active and potential mine and quarry sites afford access to water transporation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the western Kentucky Fluorspar mining district, and late Paleozoic, erosional unconformities in northeastern Kentucky.

Jan 4, 1978

From the early part of the thirteenth century bituminous coal was called "sea coal" in England, from the fact that the coal seams in the Fife and Northumberland fields outcropped on the shores of the North Sea and wave action and erosion resulted in lumps of coal being found in large quantities along the shores. These were gathered by women and children and sold for fuel to replace wood. Coal first reached London by sea, and there was a "Secole Lane" in that city in 1228. The term was gradually applied to all coal and for some hundreds of years all coal in England was called "sea coal", and the term is not yet obsolete there. Another reason for the use of a defining word was the fact that from time immemorial, in England and elsewhere, the word coal meant char-coal, or coal made from wood, as this was the common fuel of those times when anything other than natural wood was burned. The biblical references to coal all mean wood-coals or charcoal, and one must be careful in writings prior to at least 1750, when "coal" is used to be sure that it means stone, or mineral coal, rather than wood or charcoal. "Sea-coal" was in common use along the Atlantic seaboard until after about 1780; the first map showing coal in Pennsylvania, Ohip and Kentucky, made as of 1750, used the term "sea-coal here."2 In the interior stone coal was used by the early writers almost entirely, partly to differentiate it from charcoal, but largely because it was found with stones and rocks, and in most places then had the same value. "Fossil" coal was used by Hamilton in 1790. Jefferson called it mineral coal and pit coal in 1781. The term mineral coal was usually used in the governmental references to it as late as 1850, but the present use of bituminous coal began as soon as anthracite came on the market in 1820. Both mineral and stone coal still survive in the laws of several states specifying the weight of a bushel of coal.

Jan 1, 1942

By Adrian Brown

INTRODUCTION The primary tool which is available to improve the stability of an open pit mine at a given slope angle is control of groundwater pressure. This paper sets out the methods by which water pressure control can be achieved in large mines in different materials. The emphasis of this paper is on large mine slopes because. these slopes exhibit the greatest need for groundwater control, the greatest economic benefit from groundwater control, and the greatest technical challenge in achieving groundwater control. STABILIZATION USING MTER PRESSURE CONTROL Groundwater pressures reduce the stability of slopes in two fundamental ways, as shown schematically in Figure 1. In the example, a horizontal failure surface intersects a vertical joint or weak zone. Water pressure acts: o On the base plane to reduce the normal force on the sliding surface and hence reduce frictional resistance to sliding, and o On the vertical back plane, to create a driving force for the system.

Jan 1, 1983

By Felix Shay

THE Agua Fria mine is in eastern Honduras at Lat. 140° 06' N., Long. 86° 36' W. Danli, the seat of the local municipal government, is the nearest town. The property is approximately 44 miles east of Teguci-galpa, the terminus of a truck road from the Pacific coast. The mine lies at an altitude of 3300 ft. with surrounding elevations as high as 6000 feet. For 20 years the oxidized croppings of the Agua Fria vein had been worked intermittently when in 1927 an attempt was made to open the property. A shaft was sunk 300 ft. and considerable ore was blocked out, but before a mill could be installed financial difficulties arose and the mine reverted to the original owners. Erle P. Halliburton, of Los Angeles, purchased the property in 1934. At that time a careful consideration of all factors involved showed that air transport was the only practical method of moving the equipment and machinery necessary to commence production. The other alternative was by muleback, which required sectionalizing all equipment to a maximum load of 200 lb., and during the rainy season this type of freighting was subject to serious delays. It was decided to purchase a trimotor Ford powered by three Pratt and Whitney Wasp B motors developing 400 hp. each. There were several reasons for the choice: (1) this type of plane was available at a reasonable price, owing to its replacement by faster models on most of the airlines in the United States; (2) the ship was capable of carrying a pay load of 3000 lb. over the required distance; (3) since this airplane had been widely used there would be no difficulty in securing competent personnel or in purchasing spare parts. It was necessary to rebuild the plane for cargo service. The windows were removed and the fuselage was entirely covered. A hatch was cut in the top of the fuselage to receive heavy crane loads and pieces of freight that were too large or too long to go through the rear door. The seats were removed and the interior of the plane was lined with Duralumin sheets. A heavy-duty landing gear was installed and the floor was reinforced.

Jan 1, 1940