Search Documents

By W. Rostoker, H. Nichols

It has been demonstrated in previous work1'2 that wetting of aluminum alloys by liquid mercury can cause fracture to occur with substantial suppression of prior plastic flow. This has been interpreted as the action of a critical liquid species in reducing the cohesive strength of a stressed solid at sites of potential crack nucleation. In this way the critical transverse stress for fracture nucleation is reached at much lower stresses than is normally the case. The stresses for both fracture nucleation and fracture propagation are depressed by the same mechanism. In so doing the plastic-energy component of fracture energy is reduced to a level which is of the same order of magnitude as the surface, interfacial, or cleavage energy. Recent work2 has illustrated the influence of dispersed precipitates, cold work, and combinations of these on brittle fracture associated with plastic strains of the microyield order of magnitude. This has been rationalized in terms of the contribution of internal microstress fields to the stress magnifications at points of obstruction of active slip bands in a stressed metal. The presently reported studies on an Al-4-1/2 pct Mg alloy amplify this subject by introducing thermal-mechanical conditions which can produce strain aging. As amply demonstrated by Phillips, Swain, and borall, the tensile behavior of aluminum alloys containing magnesium reveals a yield-point elongation and successive discontinuous elongations over the whole plastic-strain range. This gives a stepped or serrated character to the stress-strain diagram. The yield-point elongation is not temperature-dependent. On the other hand, the discontinuous extensions in the plastic-strain range are gradually suppressed by lower temperatures of testing. At -78"C, only the yield-point elongation persists. The yield-point elongation itself can be suppressed by rapid quenching to room temperature from an annealing temperature of 500°C. The argument presented by Phillips et 1. and Cottre114 is that the yield-point elongation derives from surmounting at a critical stress the restraint to slip by grain boundaries which have been reinforced by appreciable magnesium-atom segregation. The serrated character of the plastic-strain range is the result of rapid strain aging during the test. This is made possible by the inevitable proximity of magnesium atoms to any dislocation line. In the Al-4-1/2 pct Mg alloy there is one magnesium atom for every twenty-two aluminum atoms and, with a coordination number of 12, a magnesium atom is on the average only about two atomic distances from any given lattice site. Rapid strain aging is therefore a reasonable expectation. A study of mercury embrittlement of the Al-4-1/2 pct Mg alloy (commercial designation 5083) provides an opportunity to relate the interplay of grain size, grain boundary restraint to slip and strain aging in the brittle-fracture process. One lot of commercial sheet material of 0.125-in. thickness was used for all of the tests. The specimen shape and test procedures used were the same as those described in a previous publication.2 A range of grain sizes between 0.0057 and 0.0125 mm was produced by various combinations of plastic prestrain and annealing. The coarsest grain was somewhat elongated in shape. In this case the measurement was taken in the direction transverse to the axis of tension as more meaningful to a brittle-fracture process. In the annealed condition, specimens wetted with mercury failed with zero permanent elongation at stresses slightly below the normal yield point, i.e., stresses at 0.05 to 0.2 pct strain. Since this occurs before yield-point elongation can begin, fracture derives from slip contained within individual grains and restrained from propagating across grain boundaries. No significant difference in wetted fracture stress was observed between specimens which had been water-quenched or furnace-cooled from the annealing temperatures. This signifies that the degree of magnesium segregation at grain boundaries

Jan 1, 1964

By Howard N. Eavenson

Waste of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. Average Recovery The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered—it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed 'that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed—often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal—is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1947

By Howard N. Eavenson

Waste of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. Average Recovery The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered—it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed 'that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed—often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal—is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1947

By Charles Morgan

AN increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). PROSPECTING Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body.

Jan 1, 1937

By W. Blaschke, E. Malysa

INTRODUCTION In recent years in Poland, a problem connected with the occurrence of a considerable amount of liberated galena grains in size fractions under 1mm has arisen in the zinc-lead processing area. Operating practices have included crushing of ore particles under 0.2 mm followed by flotation. Jigs were applied to separate the concentrates from size fractions under 10 mm and to prevent the galena overgrinding. However, the fractions being too wide, the jigs have not worked effectively, in spite of the great differences in specific gravities of galena, blende and gangue minerals. Fine galena grains move into light fractions in considerable amounts and hence are overground. Therefore, the flotation becomes difficult and galena is lost in its tailings. These losses could be avoided by introducing separation in the grinding and classification circuits. The amount of 0-1 mm fraction is great; therefore, the application of concentrating tables or other kinds of jigs is impossible from an economic point of view. Taking these factors into account, the possibility of application of pinched-sluices was investigated. These are simple devices without moving parts, they have a high output for the unit areas, and their water and energy consumptions are low. In this paper, the results of zinc-lead ores beneficiation in pinched-sluices are presented.

Jan 1, 1980

By C. W. A. Newey

I would like to make the following points in connection with the studies of the deformation of NiAl reported in the recent paper by Wasilewski, Butler, and Hanlon. 1) Much of their paper is concerned with demonstrating that slip occurs on either {110)(001) or {100)(001) systems. In their discussion they state "the existence of (001) as the basic slip direction can thus be considered established." This fact was established by the earlier studies of Ball and Smallman.32 Ball and Smallman also concluded that the slip plane was of the type (110) and they showed that cross slip or pencil glide on orthogonal (110) planes could produce macroscopic slip on planes of the (001) zones, e.g., (100). Wasilewski et al. refer to this paper by Ball and Smallman but not in connection with the slip system determinations. 2) Wasilewski et a!. eliminate the possibility of (111) slip in NiAl on dubious grounds. Their statement that ('the very high yield strengths of the (100) oriented crystals", in which (001) slip is constrained, "immediately ruled out the possibility of {110)(111) slip" cannot be accepted unequivocably; it would be reasonable if the crystals were completely brittle but they are not, as Wasilewski et al. and others33734 have shown. Their elimination of the possibility of (111) slip in a crystal compressed along [227] is misleading since there is no obvious reason why (111) slip should occur in a crystal of this orientation. In fact, from an analysis of the macroscopic surface markings on deformed (100) stoichiometric crystals, Pascoe and Newey34 have deduced that slip occurs on systems of the type {211)(111) and {321)(111). 3) Polycrystalline NiAl is known to undergo general deformati~n.Having emphasized that general deformation is impossible if only (100) slip occurs, it is a pity that Wasilewski et al. do not attempt to account for the disagreement between theory and their experimental results. Of course, (111) slip can provide the additional independent systems required for general deformation.

Jan 1, 1969

By D. L. Pentz

The use of "probability" methods in slope stability analysis has been practised by geotechnical engineers for some time. This paper questions whether the term probability has been properly used since in many cases the term is used in a classical statistical manner only to describe frequency distributions of data. This paper proposes a definition of the term probability which includes the engineers' subjective state of confidence for all critical parameters. Such parameters may include the slope stability model, undetected structural features, strength, groundwater pressure distribution, and geological framework. This process does not make a "better" analysis but it does force the geotechnical engineer to state his opinion in such a manner that others can understand and if necessary, criticize the assumptions. Further, this technique forces the question, "What impact would failure of a slope have on the production schedule or costs of a mine?" The level of risk taken in adopting a particular slope design strategy in a mine is not a question of what Factor of Safety should be selected but, rather, what trade-offs result from steeper slopes and the associated costs of failure. This paper also presents several simple probabilistic techniques which, though widely used in other fields have been all but ignored in geotechnical slope stability analyses. These include the use of stratified sampling to optimize Monte Carlo uncertainty approaches, and the use of simple functional approximations rather than complex stability models in probabilistic analysis. The author presents a case example of this technique and discusses the results in comparison with more traditional methods.

Jan 1, 1983

By R. Laird Auchmuty

FOREWORD THE A. I. M. E. Subcommittee on Bituminous Mining has been trying for several years to secure the information that was collected by the Marquette Cement Manufacturing Co. on the subsidence of its property caused by mining coal beneath it. The Marquette company was willing to have these data used, but it was impossible to obtain them because the records had been filed away. About two years ago these records became available and the engineering data presented herewith were compiled from them by R. L. Auchmuty, assisted by L. E. Young, who was connected with the collection of the information. On account of the cost, it is impossible to reproduce all of the data here, although the original information is on file with the records of the Committee on Ground Movement and Subsidence. The accompanying charts show representative and average data and give only the engineering information with enough description to tell how it was obtained. It is hoped that all of those connected with the original case will participate in the discussion that this will bring forth. HOWARD N. EAVENSON, Chairman, Subcommittee on Bituminous Coal Mining.

Jan 1, 1931

By G. Bhat, J. F. Libsch

lsoembrittlement curves depicting the influence of time and temperature in the range 800' to 1260°F (425' to 680°C) on the development of embrittlement in a commercial chromium alloy steel and a commercial molybdenum alloy steel are presented. Two distinct regions of embrittlement occur in the chromium alloy steel: I—at 800' to 1000°F (425' to 540°C) and 2—in the region just below the lower critical temperature. Embrittlement is most pronounced at 800' to 1000°F, decreasing very rapidly with increasing temperature above this region, only to increase again as the lower critical temperature is approached. The data suggest two distinct modes of embrittlement with possible superposition of the two modes at extended embrittling times in the temperature range 1100° to 1150°F (590' to 620°C). While the molybdenum alloy steel shows little susceptibility to embrittlement at 800' to 1000°F (425' to 540°C), considerable embrittlement may occur just below the lower critical temperature. THE subject of temper embrittlement in alloy steels has received considerable attention in the last few years. Points of view on the mechanism of embrittlement differ, however, resulting in part from the incompleteness of the data developed and in part from the speculation regarding the susceptibility of plain carbon steel to temper embrittlement. Libsch, Powers, and Bhat1 carried out short-time embrittling treatments on an AISI 1050 steel and demonstrated that hardened plain carbon steels are quite susceptible to embrittlement when tempered in the range from 850°F (455°C) to the lower critical temperature. The isoembrittlement diagram,' representing the embrittling characteristics of this steel, is reproduced in Fig. 1. It is evident from the shape of the curves shown that embrittlement in plain carbon steel increases progressively with both temperature and time in the embrittling range. A comparison of the isoembrittlement diagram for AISI 1050 steel with that presented by Jaffe and Buffum' for an SAE 3140 steel shows that up to 930°F (500°C) the isoembrittlement characteristics of the plain carbon steel are similar to those of SAE 3140 steel, although the embrittlement is much more severe in the latter steel. Above 930°F (500°C), the rate of embrittlement in the plain carbon steel increases continuously with increasing temperature; whereas, in the SAE 3140 steel, the embrittlement rapidly decreases. The influence of alloying elements upon embrittlement during tempering thus appears to cause a decrease in embrittlement above the region of maximum embrittlement, i.e., 850" to 1000°F. The question naturally arises as to what effect individual alloying elements have upon the embrittling characteristics of the plain carbon steel. Current knowledge on the influence of alloying elements on temper brittleness may be found in the review papers of Hollomon" and Woodfine. Hollo-mon," from the results of other investigators, has shown that, in general, the amount of embrittlement increases with increasing alloy content (except for molybdenum and possibly tungsten and columbium). Jaffe and Buffum," by a comparison of the embrittlement in a plain carbon steel with that of a SAE 3140 steel postulated that the presence of alloying elements in moderate amounts tends to retard the development of temper brittleness. It is difficult to determine what effect chromium has upon temper brittleness, since most of the information available has been based on the combined effect of other elements with chromium, particularly nickel and manganese. However, Wilten, and recently Jolivet and Vidal,' Vida1, and Woodfine have reported that chromium steels are temper brittle, that the embrittlement is reversible with a maximum rate of embrittlement at approximately 975°F (525"C)," and that the susceptibility increases with increasing amounts of chromium. Taber, Thorlin, and Wallacel" have found a large embrittling effect with increasing chromium content in a medium C-Mn-Ni steel. But Hultgren and Chang," from their experiments conducted on synthetically prepared ternary Fe-C-Cr alloys, could not conclude that these alloys are susceptible to temper embrittlement. However, on addition of manganese or phosphorus, these Fe-C-Cr alloys became susceptible, from which fact they concluded that the embrittlement developed in chromium-bearing Fe-C alloys is due chiefly to the presence of these elements. Considerable data are available to show that molybdenum decreases the susceptibility of steel to temper embrittlement. However, its effectiveness in preventing or decreasing embrittlement appears limited to its presence in small amounts. Vidal" has shown that a plain 2 pct Mo steel was susceptible. Hultgren and Chang" also have shown that molybdenum additions in excess of 2 pct to synthetically prepared Ni-Cr steels did not prevent embrittlement. Jolivet and Vidal' and Lea and Arnold found that molybdenum reduced temper brittleness. Lea and Arnold further stated that molybdenum decreased the rate of embrittlement rather than the total amount of embrittlement, whereas Preece and Carter" have shown that the presence of molybdenum greatly reduces the equilibrium extent of the change at a given temperature but does not appear to influence the rate of embrittlement. There appears to be very little information as to how molybdenum by itself affects the temper brittleness susceptibility of a plain carbon steel.

Jan 1, 1956

By D. A. Vaughan

COMPOUNDS in the U-N system have received little attention since the work of Rundle, Baen-ziger, Wilson, and McDonald in 1948.' They described the three nitrides UN2, U2,N2, and UN as the only phases in this system. The region between UN and U,N, was reported to consist of the two phases while the region between U,N, and UN, is a homogeneous solid solution in which the U,N3, structure transforms with increasing nitrogen content into the UN, structure. This report presents the results of an X-ray diffraction study of the phases present in the region of the diffusion gradient on uranium reacted with nitrogen at several temperatures between 500" and 915°C. Several samples of uranium used in U-N gas-metal reactions by Mallett and Gerds were available for X-ray diffraction study of phase composition through the diffusion gradient. X-ray diffraction data were obtained using filtered iron radiation at intervals through the diffusion layer of the several samples on filings or turnings at approximately 0.001 in. increments down to the base metal. Representative X-ray diffraction patterns from various layers through the case on uranium after nitriding at 850°C are shown in Fig. 1. These data show that three different phases are present in the

Jan 1, 1957

By J. L. Moriarty, Irving Johnson, H. M. Feder

The crystallization of ternary alloys has been studied as a coprecipitation phenomenon by measuring the substitutional carrying of trace metals with CeCd11 precipitating from liquid cadmium. The Doerner-Hoskins logarithmic distribution law has been found to apply in all cases; the coprecipitation coefficients obtained were: 1.48 (La), 1.06 (Th), 0.63 (Pr), 0.24 (Gd), 0.17 (Sm), 0.13 (U), 0.10 (Er), 0.09 (Sr). Li, Na, K, Ba, Y, Sc, and Zr were not measurably carried. It has been observed that coprecipitation was most extensive for those tracers which form with cadmium an intermetallic compmdnd isostructural with CeCd11 or closely related thereto. For these tracers an inverse relation between Solubility in cadmium and coprecipitation coefficient was noted. THE partition of impurities between the liquid and solid phases of a metal or a congruently melting intermetallic compound has been extensively studied by the methods of zone melting.' However, when the composition of a liquid alloy and of the solid phase crystallizing from it differ grossly, partition of an impurity cannot be investigated in this manner. Partition of the impurity under equilibrium conditions may be studied by investigation of the appropriate phase diagram and partition under nonequi-librium conditions may be studied by observation of coring in the solidified alloys.2 The nonequilibrium case is of special interest in metallurgical practice because many complex alloys are cooled too rapidly to permit the uniform diffusion of impurities throughout the crystallizing phase(s). With this in mind, the present study was undertaken to obtain quantitative data on the phenomenon of coprecipitation via substitutional solid solution in certain metallic systems. It will be noticed that rather than adopting metallurgical ter- minology we have chosen to refer to the partition of impurities during alloy crystallization as coprecipitation.3 In the terminology of coprecipitation the impurity is referred to as the tracer and the precipitating phase as the carrier. From aqueous solution, coprecipitation may occur as a result of adsorption on the surface of the carrier, by occlusion of the liquid within the crystals, or by solid solution of the tracer in the carrier. By slow cooling of liquid metallic solutions it is relatively easy to form large, regular crystals of the carrier; the effects of adsorption and occlusion may be minimized and the influence of substitutional solid-solution formation may be made to predominate. Previous studies of the crystallization of some intermetallic compounds4 and of copper, silver, and gold5 have shown that the coprecipitation or partition behavior of trace metals is entirely analogous to that observed in aqueous systems when ionic substitution occurs, e.g., coprecipitation of Ra++ with BaSo4. The precipitation of CeCd11 from liquid cadmium was chosen for study. This choice was influenced by the following consideration. If the relative atomic sizes of the tracer atom and the atom for which it substitutes determine the tendency to coprecipi-tate, then a lattice having a substitutional site of well-defined size would be desirable. In CeCd116 (structure type cubic BaHg117) the cerium atom is completely surrounded by a cage of twelve nearly equidistant cadmium atoms. Thus, atoms much larger or much smaller than cerium should be poorly accommodated in this cage. The choice of a lanthanide central atom allowed the testing of the size hypothesis with a number of lanthanide tracers which differed in size but not in valence or electro-negativity. EXPERIMENTAL The general technique of this investigation was to prepare a slightly undersaturated solution of carrier in liquid cadmium to which a tracer was added. The concentration of tracer was always so low that saturation over the entire temperature range investigated was never exceeded. The solution was cooled in a stepwise fashion. After each step a por-

Jan 1, 1964

By E. T. Turkdogan, M. L. Pearce

The rates of sulfurization and desulfurization of calcium aluminate, silicate, and ferrite melts by CO + CO2 + SO2 mixtures at 1550°C are reported. It is shown that for melts 10 to 15 mm deep transport of sulfide ions within the melt controls the rate of sulfur transfer. The rate data from shallow melts, i.e., 1 to 4 mm deep, have been analyzed on the basis of a diffusion or a reaction controlled process and indications are that the both processes may play a part in controlling the rate of sulfur reaction. The rates of desulfurization of silicate XVEACTION equilibria between metals, metal oxides, and gases have received considerable attention in recent years. However, the understanding of and aluminate melts increase with increasing PCO2/PCO ratio in the gas stream, the effect being most marked for aluminate melts. The sulfide equilibrium data obtained from the present work are shown to be in accord with the results of previous studies. It is shown that carbon dioxide has a measurable solubility in silicate, aluminate, and ferrite melts. Consideration is given to the partial equilibria which control the directions and the rates of reactions occurring simultaneously in complex heterogeneous systems. the kinetics of heterogeneous reactions, particularly those occurring at elevated temperatures has not been improved appreciably. Almost all the metallurgical reactions occur in heterogeneous systems involving two or more phases. Although in many authoritative text books and original Papers the basic principles concerning the kinetics of heterogeneous reactions are clearly underlined, they are seldom used to the best advantage in kinetic studies, particularly those involving the metallurgical reac-

Jan 1, 1963

By Arthur Phillips

DURING the past few years considerable interest has been shown in the study of fiber, and its effect, in wrought metals. Fiber has recently been defined as a "condition of parallelism of important lines or details in the structure. "1 Briefly stated, two distinct types of fiber are commonly encountered. One results from the alignment in the direction of working of constituents, more or less segregated, such as slag, oxides, carbides and dendritic formations. The second, and least understood, type is produced by working the metal below the recrystallization temperature in such a way as to develop a parallelism of the grains. This condition is readily recognized by the pronounced elongation of the grains in the direction of working. Under certain deformational treatments the grain fragments produced by cold working tend to orient in certain definite directions with respect to the axis of extension. Furthermore, even in metals that have been annealed after cold working preferred orientations may be present. It is perhaps logical to assume that such marked parallelism of structural elements would be manifested by directional properties in the metal. As a matter of fact, tests on many kinds of materials have shown differences in varying degrees. In recognition of this condition, propel design, for many purposes, places the fiber axis in such a way as to present the direction of maximum strength to the greatest applied stress.

Jan 1, 1931

By J. B. Hiskey

The hydrometallurgical application of thiourea in processing precious metal ores and concentrates has reached the development stage. This paper reviews recent technical literature covering the process development of thiourea leaching. In addition, recent fundamental contributions are discussed. Most of the interest in thiourea leaching has involved treating high grade concentrates that have sufficient value to just the use of thiourea as a reagent. An important development in thiourea technology is the addition of SO2 to the leaching solution. This procedure effectively reduces the decomposition of thiourea and eliminates the problems of passive surface layers that limit the leaching efficiency. Results for the thiourea leaching of a bulk sulfide concentrate and a residue from the autoclave leaching of a smelter flue dust are also reported. As determined by a standard bottle roll cyanidation test, the bulk concentrate was extremely resistive to cyanide leaching yielding only 16% gold and 2% silver extraction in 24 hours. Leaching with a relatively concentrated thiourea solution (1MCS (NH2)2) resulted in 83% gold and 75% silver extraction in four hours. With the treated flue dust residue, gold extraction was about 60%. Gold and silver extraction with cyanide was sensitive to both cyanide concentration and oxidizing conditions. Cyanidation resulted in 59% gold extraction and 77% silver extraction in 24 hours.

Jan 1, 1985

By Richard Bosustow, Van Dyne Howbert

The Presidio mine of The American Metal Co. is situated in the "Big Bend" region, some 45 miles over state highway south of Marfa, a station on the Southern Pacific R.R. It lies 20 miles by road north of the Mexican border, in semidesert surroundings typical of this general section of the United States and the adjoining part of Mexico. All supplies are hauled in by truck from Marfa under contract. The concentrates and precipitates produced by the mill are carried by the same trucks to Marfa, from whence they are shipped, respectively, to the El Paso and Selby plants. History The mine was discovered about the year 1880 and was soon thereafter taken over for development by some army officers stationed at Fort Davis, Texas. It was later operated by the Presidio Mining Co., which treated the ore in a small pan-amalgamation mill from 1883 until 1913, when a cyanide plant was erected which has been in continuous operation ever since. When the present company, a subsidiary of The American Metal Co., Ltd., took over the mine in April, 1926, the ore-bearing zone had been worked for about 2200 ft. to the east of I the outcrops down the dip of the formation, at which point it is at a I vertical depth of 500 ft. below the surface. Up to that time the mine had produced some 1,150,000 tons of ore averaging about 17 oz. silver. After a development campaign the company started milling again in February, 1927. Since then the production has been approximately 4700 tons per month of ore; of which the yearly average grade has varied from 19.7 to 23.2 oz. silver, $0.20 to $0.50 gold, and 2.0 to 2.5 per cent. lead. No other property in this district has ever produced tonnage of any importance.

Jan 1, 1931

By L. J. Buck

Lead smelting in the ore hearth, first practiced in Europe, whence the traditional name "Scotch hearth, and later developed in America to its present efficiency, is based upon the roast reduction process and is applicable to relatively high-grade galena concentrates. The roast reduction process embraces not only the roast reactions: 2PbS + 70 = PbO + PbSO4, + SO2 PbS + 2PbO = 3Pb + SO2 PbS + 2PbSO4 = Pb + 2PbO + 3SO2 but also, by reason of the addition of extraneous fuel, the reduction reaction: 2PbO + C = 2Pb + CO2 Thus in the ore hearth the roasting of lead sulphide, forming lead oxide and lead sulphate, the reaction of lead oxide and lead sulphate with lead sulphide producing lead, and the reduction of lead oxide by carbon producing lead, go on simultaneously. The Ore Hearth Function of the Ore Hearth.—The ore hearth, through the roast reduction process, provides for the extraction of lead and the immediate disposal of the smelting products—fume, hearth slag and lead, all of which are subsequently treated as follows: the fume is recovered in the flue system and baghouses, mixed with concentrates, and returned to the ore hearth in the form of ore mix; the hearth slag is smelted in a blast furnacc for the further recovery of lead; and the lead is refined and cast into a marketable product. Concentrates Amenable to Ore-hearth Smelting.—Only concentrates that are high in lead content, 70 per cent or more, are ordinarily considered amenable to ore-hearth smelting. Silica should not exceed 2 per cent and iron is allowable only to 4 per cent. These slag-forming constituents occlude both sulphide and mctallic lead, prevent the elimination of sulphur and decrease the lead extraction. Lime and magnesia are beneficial in that both favor a dry slag, promote elimination of sulphur, and prevent occlusions of metallic lead.

Jan 1, 1937

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-' ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration 'of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960s. During 1967 the US Bureau of Mines (USBM) assisted the Climax Uranium Co., Grand Junction, CO in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (Shabbir and Tame, 1978). Atlas Minerals, Moab, UT has used hydrogen peroxide to control vanadium and sodium levels in uranium concentrates since 1969 (Caropresso and Badger, 1973). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low-grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product. Although the hydrogen peroxide precipitation of uranium has, and continues to be used primarily as means of producing a high purity yellowcake, it has also become an important process due to the superior physical properties of the precipitate. Under normal operating conditions, the precipitate produced by the reaction of hydrogen peroxide and uranium is dense, easily filtered and dried. The final dry yellowcake is pure, high U308 assay product. Consequently, processing costs such as filtering, drying and/or calcining and drumming, can be reduced compared to ammonia, caustic or Mag-Ox precipitation.

Jan 1, 1982

By R. T. Mishler

Silver-gold. mine, in northern Mexico, with arrow veins in rhyolite. One fourth area developed has been ore. Deposits average 20 in. wide and 73 oz. silver per ton; diluted in mining to 40 oz. per ton. Developed by drifts and raises at 100-ft. intervals. Samples cut every 5 ft. Ore and waste sampled separately to make combined stoping width 3 or 3 1/2 ft. Ore reserves figured to sloping width; high assays not modified. Tonnage and assay of ore extracted higher than estimates. Ore stoped principally by cut and fill method. Cars from each stope counted and sampled. Cars check tonnage to concen¬trator within 1 per cent.; silver assay 9 per cent. high. Tonnage and assay from scopes corrected to agree with feed to concentrator. Profit or loss for each slope estimated monthly. THE Lucky-Tiger mine is a silver-gold property, situated at El Tigre, in the northeastern part of Sonora, Mexico, at, an elevation of 6000 ft. in the Sierra Madre Mountains. It is 30 miles by wagon road from the Esqueda station on the Nacozari railroad. Since its discovery in 1903, the mine has produced forty million ounces of silver. The ore has averaged 40 oz. silver and 0.25 oz. gold per ton. Copper, lead and zinc have been of minor importance, having averaged 0.4 per cent., 1.1 per cent., and 1.5 per cent., respectively. The richness of the ore,, combined with its occurrence in narrow veins, required the use of the more expensive methods of mining.

Jan 2, 1925

By T. L. Joseph

THE United States Bureau of Mines has been studying the blast-furnace process for, about ten years. An experimental furnace was developed by the bureau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.1 Royster, Joseph and Kinney§(48) found that the particle size of ore had an important effect upon the blast-furnace, process. Kinney(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of the stock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or . formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust.

Jan 1, 1930