Search Documents

By J. K. Stanley

Iron-cobalt alloys in the range of 35-50 pct cobalt are of interest in the electrical industry because they possess the highest magnetic saturation of any magnetic material known. l1,2The magnetic saturation induction of the 35 pct alloy is 24,200 gausses, compared to 21,600 for pure iron (Fig I). This difference is significant in electrical apparatus, whcre weight or space is at a premium. Saturation values higher than that for iron can be attained up to about 70 pct CO hut economics restrict the use to as low a cobalt content as possible without sacrifice of saturation. Fig 2 shows the iron-cobalt equilibrium diagram. Up to the present time, two factors have retarded the use of iron-cobalt alloys in the electrical industry for magnetic purposes.? One is the high cost of cobalt ($I.50 per pound) and the other ig the inherent brittleness of the binary iron-cobalt alloys. Straight iron-cobalt alloys up to 25 pct cobalt are ductile and easy to process to thin sheet or strip by conventional methods of hot and cold rolling, but the alloys containing higher percentages of cobalt, including those for which the saturation magnetization is a maximum (35 to 40 pct), are increasingly brittle with increasing cobalt, at least up to 50 pct, and are consequently difficult to process, either hot or cold. Work by White and Rah13 indicated that iron-cobalt alloys could be made ductile by alloying with vanadium, and after quenching the alloys (vanadium up to about 4 pct) were found to he colt1 rollable to very thin gauges. With this as a background, we resumed our work on these alloys with the objective of developing methods for economical commercial production of wide strip. For this purpose we have concentrated on the 35 pct alloy in order to obtain the highest possible saturation value. Experiments were carried out on many alloy additions to the iron-cobalt alloys and on the response of these compositions to heat treatments. This work finally culminated in a commercially producible iron-cobalt alloy which has been named Hiperco.* Materials StudIEd and Procedur' Binary alloys of iron and cobalt in the range of 35 pct cobalt are difficult to hot work (by forging or rolling) without such additions as C, Mn, Si, V, Cr, Mo, W Or perhaps others. Another beneficial effect of such additions is that they increase to a greater or less extent the strangely low electrical resistivity of these alloys about 10 microohms per cm3

Jan 1, 1948

By William Fink

APPROXIMATELY two years ago the authors obtained data that indi-cated that initial precipitation could not be detected by change of lattice parameter in the aluminum-rich aluminum-magnesium alloys. Some of these data were first published in a brief note in MINING AND METAL-LURGY1. Cast specimens were used at that time and they showed initial precipitation relatively sooner than sheet material of the sane composi-tion. For this reason a more thorough investigation has been carried out using a homogenized aluminum-magnesium sheet containing approxi-mately 10 per cent magnesium. Materials.-The aluminum used in the preparation of the aluminum-magnesium alloy was of high purity, containing less than 0.01 per cent each of iron, silicon and copper. The magnesium was high-purity sub-limed magnesium. Preparation of Alloy.-Approximately 4 kg. of the aluminum was melted in a plumbago crucible in an electric furnace and the magnesium was added. The melt was thoroughly stirred with a graphite rod and fluxed with chlorine gas before casting. The alloy was cast in the form of a sheet ingot in a cold iron tilting mold (approximately 200 by 165 by 40 min.) and into small chill-cast, slabs for chemical analysis (75 by 40 by 5 mm.). The chemical analyses were made upon drillings from the analysis slabs. The analytical methods were those described in "Chemical Analysis of Aluminum," published by the Aluminum Company of Amer-ica. The composition of the alloy was found to be: magnesium 10.30, silicon 0.013, iron 0.008 and copper 0.005 per cent.

Jan 1, 1936

By Samuel D. Warriner

The dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee, and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able

Jan 1, 1912

By Gerhard Derge

A series of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the International Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.' There is little information available regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which more exhaustive experimental work may be done to best advantage. Experimental Procedure The first work was devoted entirely to the problem of obtaining reproducible results from a series of potential measurements. Only the methods finally adopted as standard will be described here, except when the variations from these have furnished results of interest. The cell used is shown schematically in Fig. 1. The electrolyte is contained in the vessel A (an inverted bell jar), whose ground top is fitted to the transite-board lid B. The controlled atmosphere can be admitted

Jan 1, 1938

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By Gilbert Thiessen

The use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material. Previous Work Lehmann and Stach have developed a processl,2 for separation of banded bituminous coals into their band ingredients by impact pulverization followed by screening or air separation. They found, as might be expected, that the fusain was concentrated in the very fine material. Prockat and Raute3 examined samples from dedusting plants operating in the Ruhr. They separated the dust into various screen sizes and determined the composition of each of these sizes in terms of the banded ingredients of the original coal. In the dusts examined by them, the finest material was always high in fusain, and most of the fusain contained in the original samples could be recovered from this fraction.

Jan 1, 1936

By Gerhard Derge

A series of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the International Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.' There is little information available regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which more exhaustive experimental work may be done to best advantage. Experimental Procedure The first work was devoted entirely to the problem of obtaining reproducible results from a series of potential measurements. Only the methods finally adopted as standard will be described here, except when the variations from these have furnished results of interest. The cell used is shown schematically in Fig. 1. The electrolyte is contained in the vessel A (an inverted bell jar), whose ground top is fitted to the transite-board lid B. The controlled atmosphere can be admitted

Jan 1, 1938

By C. A. Hansen

INTRODUCTION It has been the experience of the writer, during some. five years' work with electrolytic zinc, that the zinc cell is perhaps more- sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulphate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities. and cumulative impurities derived from the leaching of the ore; it also in

Jan 3, 1918

By L. C. Graton

INTRODUCTION CLEAR recognition by Lindgren1 of the important control exerted by physical conditions on the formation of ores laid the foundation for that long-sought attainment, a classification? of mineral deposits based consistently on origin. In probably no other portion of the realm of mineral deposition has the importance of physical influences been so manifest or the validity of Lindgren's genetic classification been so well proved as in that extremely important family of ore deposits which are now universally classed as hydrothermal and generally regarded as of magmatic derivation. While many varieties of deposits, some of them possessing great scientific interest and economic importance, fall outside the limits of this hydrothermal group, inclusion within it of most of the veins and a vast number of the replacement deposits of the world gives to this grand genetic class at once a dominating importance and a powerful scientific appeal. Nowhere are these vein and replacement deposits of hydro- thermal lineage more generously distributed, more extensively exploited or more thoroughly known than in the Cordilleran province of the United States. One of the respects in which these hydrothermal deposits command the interest of both geologists and mine operators is in their relation to depth: the great vertical range through which many of them have already been developed, the disappointing failure of others at relatively shallow levels, and the noteworthy downward changes in character and tenor exhibited by still others. In this hydrothermal category (if the Rand be granted place here) are included the ores of all the very deep mines of the world, ranging from 5,000 to nearly 8,000 ft., as well as of many other mines undoubtedly destined in time to attain corresponding depths.

Jan 1, 1933

By P. T. Carter, A. B. Murad, H. B. Bell

The distribution of manganese and oxygen between molten iron and FeO-MnO-SiO2 slags not saturated with SiO2 has been determined and used to calculate activities of MnO and SiO2 in MnO-SiO2 slags. These were found to be intermediate between the corresponding activities in FeO-SiO2 and CaO-SiO2 slags. THE equilibrium constant for the reaction between molten iron containing manganese and slags containing FeO and MnO, namely: FeO(slag) + Mn = MnO (slag) + Fe(1iquid) is most conveniently represented by: (MnO) Kmn== (FeOHMn] [Fe] is omitted, since for dilute solutions of manganese in iron, afe is approximately constant. When activities are used for (MnO), (FeO) and [Mn], Kmn is a true equilibrium constant and will apply to all types of slags, but when weight percentages are used, the values obtained for Kmn for different slags vary considerably. The equilibrium between iron containing manganese and relatively pure FeO-MnO slags has been investigated by several workers;1-4 the most recent investigation reported is that of Chipman, Gero, and Winkler.4 Their results, corresponding to slags containing up to 4 pct SiO2, were represented by the equation: 6440 log KMn = +2.95 In this case both slag and metal may be assumed to be ideal solutions, therefore the values of Kmn so derived represent the true constant for the manganese reaction. As the molecular weights of MnO and FeO are almost equal, weight concentration of these oxides may also be used in the above expression. Acidic oxides such as SiO2 and P2O5 affect the activities of FeO and MnO differently, so that when total concentrations by weight of FeO and MnO are used in the above expression for Kmn the values obtained are no longer constant. These will be denoted by K'mn. Körber and Oelsen5 investigated the manganese reaction using silica-saturated iron-manganese-silicate slags and found: 7940 logK'mn =3.172 This corresponds to Kmn values much higher than those obtained for pure oxide slags. The results of Körber and Oelsen, and Chipman, Gero, and Winkler are summarized in Table I. In the present investigation it was decided to study the manganese reaction using iron-manganese-silicate slags not saturated with silica, and which fell mainly between the orthosilicate join 2FeO . SiO2 - 2MnO.SiO2 and the FeO-MnO side of the ternary system FeO-MnO-SiO2. It has been shown" that the phases present in solidified slags of this part of the diagram are (FeO, MnO) and (2Fe0.Si02, 2Mn0-SiO,) solid solutions. Such an investigation would be of interest in deoxidation and also gives information on activities in liquid slags. This equilibrium has not as yet been investigated successfully. Hilty and Crafts7 attempted to examine this reaction in a rotating crucible furnace, but were unable to obtain suitable slag samples. In the present investigation one series of experiments was carried out in a rotating crucible furnace, because the success of Taylor and Chipman8 with such a furnace in their study of oxygen distribution between molten iron and (CaO, MgO) — FeO-Si0, slags suggested that it would minimize contamination of the slag by the crucible material. A second series was carried out using a wire-wound resistance furnace. Rotating Crucible Furnace Experiments In all cases the metallic charge consisted of 800 to 1000 g Armco iron containing 0.02 pct C, 0.03 pct Mn, and traces of Si. Manganese and silicon additions consisted of electrolytic manganese (99.9 pct)

Jan 1, 1953

By H. R. Peterson

The control of autogenous grinding circuits is very similar to the control of conventional grinding circuits. In both circuits the classifier must be operated to achieve the required degree of mineral liberation. Crude ore grade and grinding mill density are important in both circuits. The biggest difference between the control of the two circuits is the pronounced effect that crude ore changes have on autogenous circuits. The importance of crude grade, weight recovery, size and hardness is greatly magnified because the crude ore in the autogenous circuit is also supplying the grinding media. Crude ore sizing is a particularly critical factor in achieving efficient primary autogenous milling. Because of the above, computer control is advantageous for autogenous circuits. Changes in crude ore may necessitate rapid changes in the entire circuit control strategy, and only a computer can facilitate these changes. Also, the techniques of control are very different for conventional and for autogenous grinding. Set-point control is usually satisfactory in conventional circuits, but the multiplicity of varying conditions in an autogenous circuit usually require some type of computer optimizing search routine. Autogenous mills can be separated into two general types. In primary autogenous mills the media is obtained from the mill feed, and in pebble mills the sized pebble media is added separately from the material being ground. PRIMARY AUTOGENOUS MILL CIRCUIT CONTROL - FIGURE 1 Power Draw Primary autogenous mills are usually run at full motor loading so production will be at maximum. Therefore, power draw must be closely controlled; this is done by adjusting feed rate. The versatility of computer control is extremely valuable for power control, especially during starting and stopping. To bring the mill power up as fast as possible at

Jan 1, 1982

By J. E. Elliott

ALTHOUGH the firm in which the writer is a partner is not exactly the pioneer in the coring of rotary-drilled wells in Southern California, it has taken the lead in bringing coring to its present status. To the Shell Company of California belongs the, honor of having first used the core drill in its endeavors to locate subsurface structures west of Santa Fe Springs. Following those operations, similar work was done near Wasco in the San, Joaquin Valley. Results of the latter core drilling were successful, in that they made it possible to determine the under-ground structure. At, about the same time that the Shell Company was doing the work at Wasco, it was experimenting in the use of the core drill in connection with rotary-drilled holes. The oil sands in its dis¬covery well at Signal Hill were located by means of the rotary core drill. In 1921, in view of the trouble that the operators were having in the fields of Southern California, and particularly at Huntington Beach, R. E. Collom, of the State Mining Bureau, called their attention to the possibilities of the core drill for eliminating many of the serious problems that were facing them. It was this same difficulty encountered by the operator in locating the oil sands that caused the writer to enter into con-tract core drilling; late in 1921 the California operators became converted to the advantages of that method, and in the short space of one year core drilling in rotary-drilled holes has risen from a theory to an established practice.

Jan 10, 1923

By Roshan Bhappu, Laszlo Dudas, Herman Maass

Introduction Chemical and mineralogical constitution play a very important role in the processing of ores because they dictate the method, either physical or chemical, for extracting the mineral or metal. Similarly, the mineralogical nature of the ore, especially the grain size of the valuable minerals, is very important in its processing. The fineness of the grain may be such that physical separation pro- cesses may be eliminated in preference to chemical techniques. In the past, very little attention has been devoted to the geo- logical and mineralogical occurrences which may be potential sources of ores by both the geologist and mineral processing engineer. On the one hand, geologists have devoted less attention to lower grade, complex mineral deposits, and, therefore, may have inadvertently curtailed an exploration 2rogra.m. On the other hand, the metal- lurgists have neglected to study in detail the geological environ- ments and mineralization of potential ores with the view of deter- mining the critical parameter that could assist in economically processing complex submarginal deposits. In the final analysis, a chemical processing technique converts the valuable metals to a mobile state under conditions similar to those which deposited originally in the host rock. The relationship between ore-genesis and chemical processing is close when the process of mineral or metal deposition in a particular ore deposit is understood--putting the metal in solution by reversing the process of deposition is re- latively easy. For this reason, some researchers and educators have been stressing the importance of ore-genesis, geochemistry, mineral equilibria, and ionic equilibria in studying and explaining the

Jan 1, 1974

By H. H. Hasler

THE mining and removal of coal from two or more beds, either simultaneously or consecutively, in vertically adjacent areas have always been matters of concern to mine operators from both operating and recovery points of view. However, with the progressive introduction and use of electrical and mechanical facilities, such problems assume even greater proportions. In this paper typical cases occuring in Cambia County, Pa., are given and procedures whereby such problems may be .greatly reduced, if not entirely eliminated, are suggested. Throughout a considerable portion of the Central Pennsylvania bituminous coal region, particularly in Cambria County (Fig. I), the portion of the region to which references in this paper are made, large areas are encountered where two or more beds of coal occur and have been mined extensively since the earliest days of mining in the county. Generally, operations were commenced in one bed of coal on a property, following which, as conditions appeared to warrant, operations were commenced in another bed or beds on the same property, in some instances by the same operator. Operating results by no means have been uniformly successful, as the following review of some typical cases indicates, partly because of lack of experience in earlier cases and in certain later cases to disregard for the experiences of earlier operators. It is suggested that repetitions of such failures may be reduced largely, if not eliminated entirely, by adherence to a few basic principles founded upon past experiences. Geology and Stratigraphy The geology, stratigraphy, and relief of almost all of Cambria County have been studied and reported at length by the U. S. Geological Survey in its Johnstown, Ebensburg and Barnesboro-Patton Folios and other publications, by the Pennsylvania Geological Survey and by various individuals. All exposed rocks occurring within the boundaries of the county are of sedimentary origin, consisting of alternate beds of sandstone, slate, shale, fireclay, coal, limestone, etc., and all have been classified by the U. S. Geological Survey as extending from the upper strata of the Catskill formation, Devonian system, to and including, in a few hilltop areas, the lower strata of the Monongahela formation, Carboniferous system. Included within that range is the Allegheny formation, Pennsylvania series, which embraces all of the commercially important beds of coal that occur in the county, viz., the A, or Brookville, to the E, or Upper Freeport, both inclusive, shown in Fig. 2. The measures are traversed by a series of anticlines and synclines, extending in a northeasterly and southwesterly direction, which form broad, gently sloping basins (flat to 15 pct pitch, exceptionally to 25 pct). However, the topography of the surface is such that long lines of outcrops of all beds of coal overlying bed B, and to a limited extent bed B also, occur over large areas, a factor which contributed to the early and extensive development of mining activities in the county. Earliest mining developments of commercial importance were made in B, C', D, and E beds of coal, and it is in these beds that the principal mining operations are being conducted. To a limited extent, mining operations also have been conducted in local areas in the A, B rider and C beds. Coal beds being mined today range in thickness from approximately 28 to 60 in. Intervals between the respective beds of coal are variable but conform somewhat to the following general averages: A to B, 60 to 100 ft.; B to C, 50 ft.; C to C', 70 ft.; C' to D, 45 ft.; and D to E, 45 ft. The following are typical mining cases obserced over a period of years in various parts of the county.

Jan 1, 1952

By W. R. Strickler, P. Hazebroek, M. Prats

The pressure and production behavior of a homogeneous cylindrical reservoir producing a single fluid through a centrally located vertical fracture of limited lateral extent was determined by using mathematical methods to solve the appropriate differential equation. It is assumed that there is no pressure drop within the fracture — that is, that the fracture capacity is infinite. It was found that the production-rate decline of such a reservoir is constant (except for very early times) when the flowing bottom-hole pressure remains constant. The production-rate decline increases as the fracture length increases. Thus, the lateral extent of fractures can be determined from the production-rate declines before and after fracturing or from the decline rate after fracturing when the properties of the formation and fluids are known. The production behavior over most of the productive life of such a fractured reservoir can be represented by an equivalent radial-flow reservoir of equal volume. The effective well radius of this equivalent reservoir is equal to one-fourth the total fracture length (within 7 per cent); the outer radius of this equivalent reservoir is very nearly equal (within 3.5 per cent) to that of the drainage radius of the fractured well. The effective well radius of a reservoir producing at semisteady state is also very nearly equal to one-fourth the total fracture length. It thus appears that the behavior of vertically fractured reservoirs can be interpreted in terms of simple radial-flow reservoirs of large wellbore. INTRODUCTION An earlier report1 has considered the effect of a vertical fracture on a reservoir producing an incompressible fluid. That investigation of the fractured reservoir producing an incompressible fluid was started because of its simplicity. Thus, pertinent behavior of fractured reservoirs was obtained at an early date, while experience was being gained of value in the solution of more complicated fracture problems. One of these more complicated problems, and the one discussed in this report, considers the effect of a compressible fluid (instead of incompressible fluids) on the production behavior of a fractured reservoir. In the incompressible-fluid work mentioned, it was shown that the production rate after fracturing could be described exactly by an effective well radius equal to one-fourth the fracture length whenever the pressure drop in the fracture was negligible. Because of the simplification in interpretation, it is a matter of much interest to determine whether the production behavior of reservoirs producing a compressible liquid could be described in terms of an effective well radius which remains essentially constant over the producing life of the field. The details of the mathematical investigation are given in the Appendixes. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable circular cylindrical outer boundary of radius re. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. Fig. 1 indicates the general three-dimensional geometry of the fractured reservoir just described. When gravity effects are neglected, the flow behavior in the reservoir is independent of the vertical position in the oil sand. Thus, the flow behavior in the fractured reservoir is described by the two-dimensional flow behavior in a horizontal cross-section of the reservoir, such as the one shown in Fig. 2. Production is due to the expan-

By D. O. Rausch

The economic relationship between steepening slopes and decreasing waste removal requirements ahead of ore mining is one of the most important factors in the design of open-pit mines. The steepness and stability of the pit slopes often spells the difference between ore and waste profit or loss in low cost open-pit operations. Unfortunately, the technology necessary for designing stable rock slopes is still in the early stages of development. Past and current pit-design methods have been, and still are, empirical, with rock slopes frequently made too steep or too shallow. As such, large expenditures are often made for correcting slopes after failures occur, or for unnecessarily removing more waste material than required.

Jan 6, 1965

By Alan U. Seybolt

IN examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was sufficiently pronounced to warrant some investigation [ ] of the annealing characteristics of such compositions. EXPERIMENTAL PROCEDURE The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace, under a charcoal or [ ] electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to ¼ -in. thickness, and annealed for ½ hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a go per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1941

By J. F. Kemp

IN submitting an additional contribution to the discussion on ore-deposits in the recent volumes of the Transactions, it is my desire to adhere closely to matters of material importance as affecting the actual processes. Judging from the discussion by Professor Van Hise, and from one or two reviews or other articles by associates of his in geological work, the impression seems to prevail that, in so far as my paper* referred to ,his masterly essay,†I was guilty of misconceptions regarding both the part attributed by him in it to the igneous rocks and the ubiquitous presence of the ground-water. I should regret extremely to be wanting in these particulars or to have misunderstood one for whose great services in this and other branches of geology no one has a higher esteem than myself. I have, however, in the most careful way, and with these points in mind, read his essay again, anti, taking it as a whole, I cannot gain any different impression of relative magnitudes than the one first received. The importance of the igneous phenomena and the restrictive influence of the processes described by " cementation " in their effect upon the ground-water, as set forth in Professor Van Hise's " Discussion " (Trans., xxxi., 292), impress me as being in very marked contrast with the same things in his first essay. If the point seems to anyone of sufficient importance, it can easily be decided by reading the originals. My paper was the result of some years of observation, reading and reflection, and was meant to be an independent contribution, controversial only in some subordinate particulars. In depicting the drama of the deposition of ores, I cannot but feel that Professor Van Rise assigned to the chorus and the scene-shifters some characters which, it seems to me, should

Jan 1, 1913

By Anthony Anable, J. V. N. Dorr

When separate treatment of sand and slime by cyanidation was the rule rather than the exception, as now, and when gravity concentration, rather than flotation, was the accepted method of dressing copper, lead, zinc and other base ores, classification was a separate step in ore treatment. Today, however, the picture is much different. The trend toward all-slime treatment in cyanidation and flotation has made fine closed-circuit grinding essential, and the mechanical classifier is of equal importance with the mill in the preparation of an ore for its treatment. Actually, a mill and classifier are a unit, a variation in either affecting the desired results. In developing this thesis—the mutual interdependence of the rotary mill and the classifier in modern fine-grinding practice—it would be well to consider first the different types of classifiers and mills in use today, their scope and limitations and the factors governing their selection. From such a basis as this a logical approach may be made to modern closed-circuit fine grinding, the evolution of multiple-stage grinding practice, the relation of the classifier to the mill and, finally, the trend to higher and higher circulating sand loads in the mill-classifier circuit. Such data as are germane to the subject will be given to support the thesis advanced. Mechanical Classifiers Theory.—Stokes' law, applicable to the uniform slow motion of a rigid sphere in a viscous fluid of infinite extent, states that the velocity of a particle settling under the influence of gravity is a function of the square of its radius: _ 2 g(ds - de)?2 v =9 S Where V = velocity of particle in cm. per see. g8, acceleration due to gravity d8, density of particle de, density of fluid ? = radius of particle S = viscosity of fluid

Jan 1, 1935

By A. T. Janssen

Production planning of direct-shipping ore from a number of relatively small deposits serves to sequence development and mining of these deposits so that both long- and short-range demand can be met while the timing of development cost is such that the average annual rate is minimized. Hand-computed methods have the disadvantage that they require substantial effort and time and cannot be exhaustive. The application of operations research and computers not only overcomes these disadvantages, but opens up additional applications, such as feasibility studies involving alternative mining strategies and changes in the ore market. The method employed concerns linear programming and specifically the Big-M algorithm applied to the variant on the simplex technique with penalties applied to deviations from the desired ore grade. Acceptable 20-year production schedules could be generated in relatively little time, i. e. , in less than 200 seconds for the central processor of the Control Data Corporation 6400 system of the University of Colorado in Boulder.

Jan 1, 1969