Search Documents

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electrochemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are modified in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.'-a In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative and may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole. These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in Pennsylvania, carried out by the Pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, in the published literature. The potential differences across the contacts of sandstone and shale are called in this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored Well In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored with diamond tools. The potentials were first measured with fresh water in the hole. A null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and crystals surrounding a pure copper elec-

Jan 1, 1944

By F. A. Crossley

The additions: o, Sn, Zr, Cb, Mo, and V were studied for their effects on the a/a + Ti3A1 boundary of Ti-A1 base ternary alloys. These additions were chosen because of their importance to commercial titanium alloy practice—oxygen as the major impurity (in terms of influence on mechanical properties) and the others as major alloying additions. The composition and temperature ranges of investigation varied according to the system as shown in Table I. The principal means of investigation was light-microscopy. The basis of the ternary studies was the recently determined titanium-rich end of the Ti-A1 system.' MATERIALS, METHODS, AND PROCEDURES Ingots were prepared in 15 g size for all alloys except those of the Ti-Al-Mo and Ti-A1-V systems which were prepared in 20 g size. These alloys were prepared from high-purity, electrolytically refined titanium obtained from the Bureau of Mines, Boulder City Metallurgical Laboratory, Boulder City, Col., and Chicago Development Corp., Riverdale, Md., for the 15 g and 20 g ingots, respectively. The alloying additions were obtained from commercial sources, and were at least of 99.9 pct purity, except the V-15 wt pct A1 master alloy for vanadium additions. This alloy was of 98.2 pct purity; the major impurities were 0.37 wt pct Fe and 0.38 wt pct Si. The ingots were prepared by multiple melting in a nonconsum-able-electrode arc furnace. The ingots were covered with Markal coating "CR-T22" (Markal Co., Chicago) to protect them from scaling. Markal coating is applied as a slurry of solids in a volatile carrier liquid. The coated article is air dried. Upon heating to the hot working temperature the coating fuses to form a glassy, protective film. The ingots were heated to 1000°C and rolled to 0.16 in. thickness, reheating after each pass. The glassy film was removed by sand blasting. Ten mils were removed from all surfaces by grinding and/or pickling (3 pct HF, 30 pct HN03, balance water). Grinding was always followed by pickling to remove traces of the grindmg medium. Hydrogen removal was accomplished by vacuum annealing at 1000°C for 2 hr to a final pressure of about 0.02 µ Hg. This was followed by annealing in evacuated Vycor bulbs (800°C, 2 hr, ice brine quenched (IBQ)) in order to maximize ductility. The materials were then lightly pickled and cold rolled to 0.12 in. thickness or cracking, whichever occurred first. After rolling, 1/2 by 1/4 in. specimens were cut for the equilibration anneals given in Table 11 and carried out as previously described.1 Final polishing of the specimens for metallographic examination was done by electrolytic means. Specimens were first examined without etching under bright field and polarized light illumination, for this is the only means of detecting the "two-phase" phenomenon.1,2 The term "two-phase syndrome" refers to Ti-A1 al-loys which appear on the bases of their chemical, phys-ical, and mechanical properties, to be two-phase, but are actually single phase and inhomogeneous in composition. Since processing and heat treatment of the alloys of the first group were completed before the two-phase syndrome was discovered, a number of the specimens were found to exhibit this phenomenon—80 pct of those of the Ti-Al-Zr system, 5 pct of those of the Ti-Al-Sn system, 30 pct of those of the Ti-Al-Zr system. The affected specimens were homogenized by heating above the ß transus temperature and quenching. The heat treatment and working schedules to accomplish this are given in Table 111. After rolling, specimens were pickled (3 pctHF, 30 pct HNO3 in water) to remove 1 to 2 mils from the

Jan 1, 1970

By Karl L. Konnerth

THE rapidly increasing use of machinery for the mining of coal and operations incidental thereto has materially changed conditions from a safety standpoint. A few of the coal-producing states have recognized the need for specialized electrical equipment for use in mines and have introduced certain requirements in their State safety regulations, notably Pennsylvania. This paper discusses the principal problems involved in maintenance of such equipment. PERMISSIBLE: EQUIPMENT "Permissible" electrical equipment is equipment that has met certain prescribed standards for use in mines where hazardous conditions may occur and has been recommended by the U. S. Bureau of Mines. Such machinery is available on the market for most coal-mining operations--for instance, coal cutting, transportation, drilling, loading, working-place illumination, shot-firing and pumping. A notable exception is the trolley-reel gathering locomotive which, although its parts may be explosion-tested by the Bureau, has not been approved as permissible for the following reasons: I. The trailing cable is subjected to more severe service than on other equipment. 2. State regulations do not require that a working place be examined for methane before a locomotive enters it. 3. Even with two-conductor cable, imperfect or inadequate bonding may cause the emission of sparks at the wheels of the locomotive and at rail joints. 4. As the locomotive is equipped with a trolley pole, and as the trolley wire may be installed and used in unsafe territory in spite of rigid State regulations, a trolley-reel gathering locomotive is always a potential hazard. MAINTENANCE The proper procedure for maintenance of permissible equipment may be divided into three parts: (I) inspection, (2) actual maintenance and (3) changes or improvements to existing machines. To secure the fullest benefits through the use of permissible equipment it is necessary that all men involved understand the principles underlying the safety features of this equipment and realize the significance of defects, so that neglect and indifference in the maintenance thereof may be eliminated. Inspection From the standpoint of safety it is desirable no doubt to make a suitable inspection of permissible electrical equipment once a week, but the opening of every enclosed compartment at each inspection may do more harm than good. The openings to such compartments are closed with various types of covers very accurately machined, often made of the softer alloys to reduce weight, and fastened with a multitude of bolts, screws, washers, and other small parts. Frequent handling of these covers may cause sufficient damage to defeat their original purpose and intent.

Jan 1, 1941

W. M. Courtis, Detroit, Mich.: Except for free-gold ores, I have always believed in scorification. I think the crucibleassay gives silver low. We found this out at the Wyandotte works in assaying Silver Islet ore. The mine-managers made us, and also the check-assayera, run one of the duplicates by

Jan 1, 1896

By Merle L. Bowser, Lawrence W. Scott, John N. Murphy

The environmental status of underground mining operations is critical to the health and safety of the miners; particularly in a large mine, the multitude of interacting parameters that can favorably or adversely affect the environmental status makes the manpower requirement of the routine checking of specific areas and conditions a formidable one. While the concept of environmental monitoring for miners has been considered for some time, until recently the availability of sensors to reliably measure the parameters of interest severely limited the utility of such systems. The status of sensors for mine use and the evaluation of environmental monitoring systems is reviewed.

Jan 9, 1979

By Y. P. Chugh, R. A. Missavage

Moisture has been known to influence strata failures in coal mines for a long the. A concise review of what is known about effects of moisture on strata control with emphasis on the Illinois basin coal mines is presented in this paper. Some approaches to mitigate the effects of moisture-leaving coal in the roof, guniting, shotcreting, application of sealants-are then briefly discussed.

Jan 1, 1982

By O. C. Wheeler

The reports for the years 1942 and 1943 were written in 1943 and 1944, respectively, and were summarized at the meetings of the Institute in February of those two years, but the manuscripts were held until released for publication in 1945. 1942 Lack of transportation facilities during 1942 resulted in a sharp curtailment of producing operations in Colombia at the middle of the year, and production of crude for export was thus greatly affected. Total production in 1942 amounted to only 10,617,008 bbl. Of this amount the Tropical Oil Co. produced 9,453,995 bbl., which includes 126,607 bbl. of petroleum condensate, and the Colombian Petroleum Co. produced 1,163,013 bbl, from its Barco property. The following summary, showing a comparison of the number of barrels of crude produced during the years 1941 . and 1942, reflects the extent to which producing operations were reduced during 1942: These above figures do not include any production recovered from Condor's (Shell's) Casabe wells during testing operations. An active exploratory drilling Program was carried out by several of the major companies, and the year 1942 established a record for wildcatting activity in Colombia. Excluding development operations on the Shell's Casabe wells on the Yondo concession, 13 wildcats were completed. Eight of these were in the Magdalena Valley, and all were abandoned; five were on the Barco Concession, and of these four were completed as producers. Particularly notable among the petroleum developments during 1942 was the continued success of drilling operations on the Shell's Yondo Concession of Compania Colombiana de Petroleos El Condor opposite Barranca-Bermeja. In 1941 the discovery well, Casabe No. I, was drilled and completed with an estimated initial production of approximately 480 bbl. of 19 1/2 A.P.I. gr. oil per day. In 1942, seven stepouts from the discovery well were successfully completed with initial production ratings ranging from 150 to 1230 bbl. per day. An extensive wildcat program on the Barco Concession of the Colombian Petroleum Co. yielded favorable results with the completion of four producers in the Socuavo and Tres Bocas areas; a fifth test, Sardinata Norte No. I, was abandoned at 500;" feet. Wildcatting operations in the lower Magdalena Valley area were initiated in 1942 With the drilling of a deep test, El Dote No. I, by Compania de petroleo Shell de Colombia. The well was a failure and was abandoned at a depth of 10,046 (?) feet. Wildcats on which drilling operations were being conducted at the end of the

Jan 1, 1945

By Norman C. Britz, Mortimer P. Buck

THIS PAPER DEALS WITH the practices used at the Huntington, Nest Virginia works of The International Nickel Company, Inc., in hot and cold rolling nickel and high-nickel alloys. The practical metallurgical aspects are discussed and a brief description of equipment given. The alloys covered may he divided into three main groups. based on their major constituents: 1. Nickel alloys, 2. Nickel-copper alloys. 3. Nickel-chromium alloys. The nominal compositions of the various alloys which are produced in most common mill forms are given in Table 1. Nickel, a commercially pure grade of nickel containing about 0.05 pct carbon as' the chief alloying element, is produced in all common Mill forms. "L" Nickel is commercially pure nickel in which the carbon content is held as low as possible, usually less than 0.01 pct. This grade of nickel is used chiefly for spinning and for special high temperature applications where its low carbon content enhances its corrosion resistance. "D" Nickel contains 4.5 pct manganese to provide improved resistance to sulphur embrittlement at elevated temperatures. "Z" Nickel is an age hardening grade of nickel containing carbon, aluminum, and silicon as the age hardening elements. This alloy combines the cor-

Jan 1, 1948

By C. L. Dake

Iron is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and. the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.' Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil,4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble and partly insoluble.5 Their iron salts readily change from the ferrous to the ferric form, and their solubility is greatly modified by the presence of ammonia.

Jan 1, 1916

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made. his gift ?for the erection of a suitable home? for the engineering societies,

Jan 1, 1943

By Leonard Bernstein, Harry Bartholomew

MANY of the properties of metals and alloys are structure dependent. Not the least of these is the grain structure. For example, in producing alloy bonds between silicon or germanium and gold-alloy foil at temperatures above their eutectics (which are, respectively, at 370" and 356°C) but below the melting points of the individual constituents, it was found that wetting was more complete with a fine-grain structure than with a coarse-grain structure. In cases where the assemblies were held together for long periods of time at elevated temperatures, wetting was not as critically dependent on the grain structure as was the case for shorter periods of time. When liquid phase forms, it first forms in the grain boundaries due to the fact that most of the impurities are concentrated at the grain boundaries and that most impurities tend to lower the melting point of the gold alloy somewhat. In addition, grain boundaries are at high-surface free-energy levels and are thus in a more favorable condition to initiate good wetting. A fine-grain structure will have more grain boundaries per unit area than coarse-grain structure thereby making wetting somewhat easier. To make the grain structure of an alloy sys- tem visible, a satisfactory method for differentiating between the different grains of which the system is composed must be employed. For the alloy bonding system previously described, the grain structure on the foil surface is of primary interest. Conventionally used etchants for the gold-alloy system will not adequately delineate grain boundaries in their structures. For this reason an alternate method is proposed for those cases where such a determination is necessary. Foil between 0.0005 and 0.005 in. thick has been used in this determination. The equipment used in this investigation was described in a previous publication.' Essentially, it employs a resistance-type filament which can be heated up very rapidly and cooled very rapidly. A thin refractory material is placed on top of the heating element. This refractory material may be molybdenum, tantalum, tungsten, or even ceramic but its thickness should be less than 0.010 in. to minimize the temperature gradient across it. The gold-alloy foil is placed on top of this refractory material. The temperature of the heating filament is raised to 900°C and cooled down to below 100°C in 5 to 10 sec. During this cycle, the foil can be observed to plastically deform due to its own weight. With no further chemical etching, this assembly is then viewed under a standard metallurgical microscope and the grain size measured. Fig. 1 is a Au-1 pct Sb alloy at 400X magnification and Fig. 2 is a Au-1 pct Ga alloy at 130X. This technique has proved to be an adequate means for controlling processing conditions in producing large quantities of gold alloy foil.

Jan 1, 1963

By Robert Forsyth

In working the Bessemer process, the bottom of the converter has always been a source of trouble and annoyance, and the subject of more experiments, probably, than any other part of the complex mechanism called a Bessemer plant. This will not appear remarkable when the duties this important piece of refractory material has to perform are taken into consideration. In the first place, by means of the tuyeres, it delivers at a high pressure the air necessary for the conversion of the bath of metal, and has then to resist the intense

By David C. Russell

The Department of the Interior used to be a quiet, noncontroversial, almost boring agency. It, after all is the fifth oldest of the Departments, and as an old line Federal agency it has studiously performed its preservation and resource management functions in a caretaker mode--though some would say more "undertaker" than "caretaker"--locking up the body and soul of America piece-by-piece. Yes, quiet, serene. That is until Jim Watt showed up. And we have all seen that version of Mt. Vesuvius which resulted--only it was the environmentalists who blew their tops. Ronald Reagan chose Jim Watt as Secretary of this fine old agency to prove that one-third of our Nation's land and over a billion acres on the Outer Continental Shelf can work for this Nation. At the foundation of President Reagan's charge to Secretary Watt is a belief in the tenets of the free enterprise system, and in the individual freedoms upon which this country was founded. There are those who don't share this belief in democracy and free enterprise, and those who believe this 205 year experiment called the United States of America will fail. Nikita Krushchev said "we will bury you"--obviously he didn't agree with our system. An Italian sociologist, Franco Ferrorotti, said bureaucratic stagnation will kill capitalism. Certainly we have all felt the ravages of bloated bureaucracies. Perhaps one indicator in the United States is the Federal Register, that daily compilation of Government's largesse. In 1970, 20,000 pages of the Federal Register were published. A decade later, in 1980, that volume had quadrupled to 80,000 pages. The Federal bureaucracy can stagnate from excessive budgets as well. The Interior Department spent $60 million on administering Federal coal leasing in 1981. That's nearly two bits a ton for every ton of coal leased in 1981. You wouldn't stay in business very long if your administrative overhead on inventory was that outrageous. But the pessimism of our critics is apparent from more than red tape and bloated budgets. For decades America has been fasting--consuming too little of America's wealth of minerals, subsisting instead on a diet heavily reliant upon mid-east oil, with little emphasis or concern for inventorying and developing domestic energy and mineral resources. Economics--yes. But short-term, short-sighted economics. Excessively dependent upon foreign imports, of oil, cobalt, chrome and other strategic minerals, the U.S. measures its time before another embargo--or fallen Shah, or Soviet manipulation, or Saudi shift, or, as we witnessed in Egypt, assassination--an untimely loss to mankind and efforts to bring peace to the troubled mid-east. These disruptions, in addition to their tragic human tolls, impair the free world's security. Huge chunks of the United States have been locked away in dozens of single land use categories in the name of conservation, with only the foggiest idea of what resources might be denied the American people-and this at a time of unacceptable levels of energy and strategic mineral imports. More than half and perhaps two-thirds of all Government-owned lands are totally withdrawn from or severely restricted to development under the mining and leasing laws. We must continue to rid Government of the overly zealous restraints which have been keeping us from drawing upon that which can help restore our economy and national security. When we assumed responsibility, the United States was dependent on foreign sources for about 40 percent of its oil. In 1981, our oil import bill was approximately $83 billion--nearly 17 times what it was in 1972. Our reliance on foreign sources for essential minerals is even more disturbing. We must look to other countries--some unfriendly, some unstable--for 22 of 36 strategically critical minerals. Yet the energy resources on federal lands which are owned by the American people could meet our needs for centuries if properly managed. Eighty-five percent of the crude oil yet to be discovered in America is likely to come from public lands, as will 40 percent of the natural gas, 35 percent of the coal, 80 percent of the oil shale, nearly all of the tar sands, and substantial portions of uranium and geothermal energy. Our vast hardrock-mineral wealth includes untapped deposits of essential elements we now import, such as chromium, copper, platinum, and cobalt. The obvious question is, if these abundant resources can help to revitalize our economic strength and to preserve our national security, why aren't we using them to better advantage? To a large extent, the answer can be found in past decisions to restrict public access to the federal estate, thus deferring to us or our successors the tough decisions that flow from Congress' mandate to provide for environmentally responsible development of America's energy and mineral treasures. Here is the legacy this Administration inherited: In January 1981, 7 years after the onset of the Mideast oil embargo: ---Less than 15 percent of federal onshore lands were under lease for oil and gas development; ---No oil and gas leases had been issued in Alaska for 15 years;

Jan 1, 1982

By Paul W. Chase

Centralized process control has received increasing emphasis in recent years. Its application at U. S. Steel's Minntac facility for production of taconite pellets is discussed in this paper. A brief description of the flowsheet will provide background for discussion of the process instrumentation and digital system.

Jan 1, 1969

By Rufus J. Foster

During the discussion on the Preparation and Utilization of Sniall Sizes of Anthracite (page 613 of present volume), several inquiries were made concerning the use of the McClave grate, which was mentioned by Mr. Coxe as having proved satisfactory in the generation of steam at his collieries, and also at a large number of industrial estal)lishments in Scranton and elsewhere. For a more satisfactory repIy to such inquiries than could be furnished in the oral discussion, I have prepared the following paper to be included in the published proceedings. And, as the use of the fuel under consideration necessarily requires the employment of a blower to change the fire, from a condition giving an incandescent radiant heat only to one giving a hot gaseoua flame as well, I shall add a description of the McClave Argand blower and its method of action. The grate and blower combined form a complete and effective system fcr burning small fuels, such as anthracite culm, birdseye, buckwheat, bituminous slack, etc., in boiler and other furnaces; while the grate alone is now extensively used with the larger sizes of hard and soft coal in furnaces where blast is riot required. Fig. 1 is a view of the RlcClave grate as built in two sections. It is constructed on the principle best approved by practice to prevent warping and burning out; that is, it presents no long lines of

Jan 1, 1892

By John D. Morgan

THE tense international situation prevailing in the postwar period, and the outbreak of actual hostilities in Korea, directs attention to the status of United States reserves of strategic and critical materials for war. Geologists and mining and metallurgical engineers are particularly interested in this problem, since, with a few important exceptions, almost all of the materials on the official list of strategic and critical materials for stockpiling (see top of page) are metals and minerals.

Jan 3, 1951

By R. Schuhmann, J. Th. Overbeek, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.'-" Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles. The contact angle is a complex quantity because the properties of three different phases, or rather of three different interfaces, control its magnitude. Considering the interfaces close to the region of ternary contact to be plane, the relation among the contact angle and the three binary interfacial tensions is easily derived. The condition for equilibrium among the three surface tensions, Fig. 1, or the requirement of minimum total surface free energy leads to Young's equation, Eq. I: ysa — ysl = yLA cos 0 [1] According to this equation, the contact angle has one well-defined value. Actually it is found in many experiments that the value of the contact angle depends on whether the air is replacing liquid over the solid (receding angle) or the liquid is replacing air (advancing angle). The receding angle is always the smaller of the two.4 Two explanations have been offered for this experimental fact. According to some investigators,5-8 roughness of the surface causes apparent contact angles that are different for the receding and the advancing cases although the actual local contact angle may be completely determined by Eq. 1. The other explanation involves the hypothesis that the solid-air interface after the liquid has just receded is different from the same interface when no liquid has previously covered it.1,4 Adsorption of constituents of the air or liquid might play a role here. In this discussion the difference between advancing and receding contact angle will be neglected and plane surfaces where Eq. 1 describes the situation will be considered. But there is still a fundamental obstacle to the application of Young's equation. The surface tension of the liquid (rla) can easily be determined, but the two surface tensions of the solid (rsa and ySL) cannot be measured directly. Eq. 1, however, is not without value. By contact angle measurements it is possible to establish how ysl — ysl varies with the addition of solutes to the liquid phase. Also, Eq. 1 affords a convenient starting point for calculating net forces and energy changes involved in the process of bubble-particle attachment.1,2 . If for the moment surface tension of the liquid (yLa) is considered a constant, an increase in ysa — ysL, will tend to decrease the contact angle. A decrease in ySA — ysl, corresponds to an increase of the contact angle. In cases where ySA — ySL > yLa the contact angle is zero; it will only reach finite values when ysa — ysa has been decreased below YLA. Thus on the basis of Young's equation and contact angle measurements alone, it can be learned how flotation reagents affect the difference Ysa — ysl, but no conclusions can be drawn as to the effects of reagents on the individual surface tensions ysa, and ysL, not even as to signs or directions of the surface tension changes resulting from reagent additions. A quantitative relationship between the surface tension or interfacial tension and the adsorption occurring at a surface or an interface is given by the Gibbs equation, which for constant temperature and pressure reads dy = — 2 T, du, [2] where dy is the infinitesimal change in surface tension accompanying a change in chemical potential

Jan 1, 1955

By C. Wegert, L. E. Paulson, S. A. Cooley, R. C. Ellman

The Grand Forks Energy Research Center (GFERC) and Commonwealth Edison of Chicago jointly conducted tests in which 400 tons of subbituminous and lignite coals were dried in a commercial scale dryer, oil sprayed and cooled, then shipped from Pekin, Ill., to Grand Forks, N.D., and stockpiled. Cars containing raw coal and dried coal which had not been sprayed, were also transported for comparative purposes. During transit, observations were made of changes in the coals' moisture content, dust losses, and temperature.

Jan 1, 1977

By C. G. Dunn, J. L. Walter

A study has been made of the nature of the slow growth or nucleation stage of secondary recrystallization to the cube texture in sheets of high-purity 3 pct SiFe. Cube-oriented nuclei were identified and their growth observed, using surface markings together with micrographic and X-ray techniques to provide information on grain boundary interactions and the driving forces for growth. FACTORS that promote growth of certain grains during the early stages of secondary recrystallization have been considered theoretically1 but have been little explored in a direct experimental way. In certain cases,2'3 it has been reported that the primary recrystallization grains (nuclei), which eventually become secondaries, were found to be larger than the other grains into which they grew-Factors such as grain boundary "mobility" and differences in strain energy may contribute to the

Jan 1, 1961

By Fun-Den Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stabi1ity.l-3 Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe.3 Rock blocks formed by sets of parallel joints have been analyzed by Wittke.1,2 The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry. A plane of weakness is represented by its dip and strike in vector form and is reduced to the form of a linear equation. The geometry of the rock block is defined by solving the linear equations. The geometric characteristics of a rock block are based on triangles and tetrahedrons. By this treatment, the three-dimensional geometry is simplified and the number of calculations of forces and moments is reduced. Methods of finding the geometric characteristics are presented, along with equations for calculating the resultant forces and moments and the factor of safety. BASIC ASSUMPTIONS The following assumptions are used : The solid part of the rock mass is much stronger than the rock mass at the plane of weakness and the rock mass will only fail along planes of weakness.

Jan 1, 1972