Search Documents

By Thomas T. Read

Mining, which is at least twenty cen-turies old, was at first, and long, wholly a practical art. Little more than two centuries have elapsed since the inception of the idea that general education and a knowledge of natural science would be of advantage to those engaged in the mining industry. Though schools of mining began to develop in Europe early in the eighteenth century the concept of educational preparation, for technical conduct of the industry was slow in winning general acceptance in the industry itself. John Hays Hammond, in his autobiography, recalls that when he sought employment with a mining company after he had graduated from Yale and Freiberg he had to assure its executive, before being even considered for employment, that he did not consider that he had learned anything about mining. This was as late as 1880. Existence in the industry of a prejudice against education of the academic type is perhaps an explanation why inadequate provision has been made by the mining industry for the continuing education of technical employees after they enter employment, although engineering education prior to engaging in industry has now won general acceptance. I am familiar with the existence of 'loop" courses for engineering graduates in metallurgical plants, of schemes for giving mining graduates "practical experience," and of the interest in vocational courses for workmen which sprang up in the period of labor shortage during and immediately following World War I (but which quickly died when the depression of 1921 again made experienced workmen available in sufficient supply), having been chairman of a committee appointed by the Mineral Industry Education Division to make a survey of existing provisions for post-employment training for engineers in our industry. The results of that survey, reported elsewhere, clearly indicate that it is inadequate as to amount; the aim of this paper is to present evidence for belief that it is also inadequate in quality. To avoid becoming too involved, no reference will be made here to post-employment vocational training for workmen, which is a subject differing so much from post-employment education for engineers as to require separate treatment. Neither will postgraduate education for metallurgical engineers be discussed, becadse a distinction must then be made between training for research work and for plant operation, whereas mining engineers engage almost exclusively in operations. Since the situation in the coal-mining industry has been discussed at several recent meetings, that also will be passed over, and what follows should be taken as a discussion applying exclusively to the metal-mining industry. Professional Development In the operations field (both in mining and metallurgy) the work to which a beginner is assigned is seldom closely related to previous academic education. The contrast is almost as great as between

Jan 1, 1943

By James Aston

THE origin of wrought iron may be taken as coincident with the earliest record of ferrous products. The limitations of primitive methods of manufacture undoubtedly resulted in a material conforming to the general characteristics of what we now classify as wrought iron. Iron has been known from prehistoric times. It is frequently mentioned in Egyptian literature, and some samples in the British Museum are believed to date from 3733 B. C. Iron instruments, tools and weapons were used in Greece in 1400 B. C., and in Assyria and. Italy in 1100 B. C. History records their use in Central and Western Europe in 1000 B. C. And in Styria and Carinthia before the Christian era. The noted Pillar of Delhi is generally assumed to date from 400 A. D. The use of iron was general in Europe in the Roman Empire, and heat treatment of weapons and tools was then practiced. All of this early iron was the result of direct reduction from the ore. It serves to illustrate the ease with which the extraction may be effected, and to point out the well known principle that a malleable product of relatively high purity may be produced from high-grade iron ore at temperatures well below the fusion point of-the metal. The fact is also emphasized that there is no novelty in the seemingly ideal and constantly recurring attempts to effect direct reduction. Economic and engineering considerations have been dominant factors in dictating today's two-step practice in the manufacture of wrought iron and steel. Bear' in mind that all of this history antedated the blast furnace, and a knowledge and use of cast iron. It was only in attempts to get greater output by use of shaft-type furnaces, that cast iron was produced in Germany in the period 1300 to 1400 A. D. This was the result of longer contact with the carbon of the fuel, and higher temperatures in the furnace. This period marked the beginning of the existing two-stage operation, involving as the second step the refining of the. cast iron to a malleable product. For a time this was effected in small hearths not unlike a blacksmith's forge.

Jan 10, 1926

By Sherwin Kelly

The prime objective of geophysical exploration is to promote the economical and rapid dis-covery of mineral or oil deposits of commercial value. To a few this concept as applied in min-ing may signify the direct discovery of ore-bodies, but to the geophysical engineer this latter Idea is one of the most insidious and detrimental misapprehensions which he has to combat. The destruction of this annoying obstacle to the progress of geophysical exploration reveals the kernel of truth behind it, that the exploration geophysicist has for the better part of two decades been concerned primarily with the discovery of mineral formations favorable to the occur-rence of commercial ore. There is a very real distinction here, since geophysical methods are capable of discovering certain mineral formations such as sulphide bodies or quartz veins, but are totally incompetent to predict whether or not they constitute ore; that is. whether or not they contain minerals of economic value in the amounts requisite to repay extraction. The art of geophysical exploration is now, however, rapidly outgrowing these early limita-tions. The rate of this growth will in large measure depend on the recognition by the mining industry of the fact that geophysics can play a role far wider and more important than it usual-ly does now, in guiding the future exploration and development of mineral deposits. It is my own firm conviction that as time marches on we will see the methods of applied geophysics turned more and more to the delineation of both minor and major structural features. The outlining of such features having a bearing on the probable loci of mineral deposition will be of inestimable value in guiding the development of a mining district. It is in this field that there will In-evitably occur a meeting and overlapping of the activities of the exploration geophysicists and

Jan 1, 1940

By John T. Norton, Robert W. Lindsay

A number of detailed investigations of the physical changes accompanying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theoretical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suitable variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions. Previous Work The many studies of the mechanism of aging in duralumin have been more or less crystallized by a series of papers by Fink and Smith1~2~3 and a recent paper by Cohen.~ The former authors believe that a simple precipitation theory is adequate to account for the various phenomena

Jan 1, 1939

By John T. Norton, Robert W. Lindsay

A number of detailed investigations of the physical changes accompanying age-hardening have raised the question as to the possibility of some phenomenon preceding the actual process of precipitation. There is considerable evidence to indicate that in the first stages of the aging process there is a pronounced distortion of the crystal lattice. This is particularly marked in duralumin. It would be of considerable theoretical interest to know the nature of this distortion as compared with that produced in other ways and to find out whether, in supersaturated alloys, it is a necessary antecedent to the formation of a second phase by precipitation. It was believed that a study of the age-hardening char-acteristics of a normally aged alloy compared with one that had been mechanically distorted might supply some useful information on these points. In addition, information would be obtained regarding the effect of a mechanical distortion on any subsequent stage in the aging process. Duralumin was chosen as the material for this investigation because the various aspects of its aging behavior can be shown in detail by suitable variations of the aging temperature. Also, probably more work has been done on this class of alloys than on any other. In spite of the many published results, it was felt that the experiments would be significant only if all of the work were done on samples from the same source and if they were examined under identical experimental conditions. Previous Work The many studies of the mechanism of aging in duralumin have been more or less crystallized by a series of papers by Fink and Smith1~2~3 and a recent paper by Cohen.~ The former authors believe that a simple precipitation theory is adequate to account for the various phenomena

Jan 1, 1939

By George J. Bancroft

INTRODUCTION. IT is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Transactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,1 showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny,2 distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many of Prof. Kemp's, ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.5 This theory, dealing with, the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1913

By J. R. Long, T. R. Graham, C. W. Matthews, R. S. Dean

In a previous paper! the authors reported on the mechanical properties of a 65 per cent copper, 10 per cent manganese, 25 per cent zinc alloy as compared with, similarly processed cartridge brass. Additional investigations by these laboratories, on higher copper alloys, have demonstrated that at lower zinc concentrations even larger amounts of pure manganese may be added to copper-zinc alloys without exceeding the single-phase solid solution limits, and that similar increases in tensile strength, yield strength, and hardness may be obtained without excessive decreases in ductility. Several compositions in this range showed also a decided color change with increasing manganese. The normal "brassy" color was considerably lightcncd and reduced to a faint yellow cast at 15 per cent manganese. With higher manganese contents the alloys were essentially white and similar in appearance to the nickel-silver alloys. From this work it appeared that it would be desirable to determine more completely the properties of the wrought and annealed white alloys. Accordingly, a more detailed study was planned of an alloy having the composition 70 per cent copper, 20 per cent manganese, and 10 per cent zinc. This alloy remained single-phase throughout the working and annealing cycles of the preliminary tests and appeared to be' about the strongest of the white single-phase alloys. The project included also an investigation of additional alloys, deviating from this composition by 5 per cent of each of the three components to evaluate the effects of variation in composition and a study of the propertics of the central alloy made with silicothermic manganese. Material Preparation Electrolytic manganese, wirebar copper, and electrolytic zinc were used for the preparation of the alloys. Representative analysis of the electrolytic manganese seldom exceeds 0.01 per cent iron, 0.02 per cent sulphur and 0.02 per cent lead, with no silicon or aluminum. A typical sample of the silicothermic manganese metal contained 2 per cent iron, 0.81 per cent silicon, 0.16 per cent carbon, and 0.36 per cent aluminum. Melting and alloying were performed in a high-frequency furnace with magnesia crucibles. Melts were deoxidized with small aluminum additions and cast into 25-lb. slab ingots. Care was exercised in deoxidation to avoid excessive amounts of residual aluminum, which has been found to have significant effects on alloys in this system. All ingots were hot-rolled at 1200' to I300°F. and then cold-rolled with intermediate anneal-

Jan 1, 1945

By Ralph A. Sherman, E. R. Kaiser

The remarkable increase in the distribution of the small underfeed stoker for use in furnaces and boilers in small industrial plants, apartment houses and homes has brought producers and distributors of bituminous coal to consider the problem of which coals and which sizes are best suited to this market. Many papers have also appeared, mostly in the trade journals, discussing the problem of the combustion of various coals and various sizes of coal in small stokers. Much difference of opinion has been apparent in these articles; due often, it would appear, to a misunderstanding of the fundamentals of the process of combustion in the stoker fuel bed. During the past year and a half, a program of research has been conducted at Battelle Memorial Institute: (1) On the process of combustion in the fuel bed of the small stoker, sponsored by Battelle Memorial Institute, and (2) on the relation of the characteristics of bituminous coals to their performance on small underfeed stokers, sponsored by Bituminous Coal Research, Inc. As a result of this program of research, two publications have been made, one1 dealing with the problem of clinker formation, and the other2 with the relation of the size of the coal fed to the stoker hopper to that of the coal that reaches the retort to be burned. The experimental research on the relation of size to the performance of the coal is being actively continued. A publication of Bituminous Coal Research, Inc. presenting the data obtained on the performance of several sizes of four typical bituminous coals will appear shortly. Because of the early appearance of that publication, the present paper includes few numerical data. The purpose of this paper is to follow the coal from the hopper through the furnace with a discussion of the various actions that occur, in the hope that it will lead to a clearer understanding of the relation of the type of coal, the size of coal, and other characteristics, to the performance. The authors do not pretend to have obtained the answers to all the complex questions involved; many unanswered questions will be proposed on which future research work is planned.

Jan 1, 1938

By E. R. Kaiser, Ralph A. Sherman

The remarkable increase in the distribution of the small underfeed stoker for use in furnaces and boilers in small industrial plants, apartment houses and homes has brought producers and distributors of bituminous coal to consider the problem of which coals and which sizes are best suited to this market. Many papers have also appeared, mostly in the trade journals, discussing the problem of the combustion of various coals and various sizes of coal in small stokers. Much difference of opinion has been apparent in these articles; due often, it would appear, to a misunderstanding of the fundamentals of the process of combustion in the stoker fuel bed. During the past year and a half, a program of research has been conducted at Battelle Memorial Institute: (1) On the process of combustion in the fuel bed of the small stoker, sponsored by Battelle Memorial Institute, and (2) on the relation of the characteristics of bituminous coals to their performance on small underfeed stokers, sponsored by Bituminous Coal Research, Inc. As a result of this program of research, two publications have been made, one1 dealing with the problem of clinker formation, and the other2 with the relation of the size of the coal fed to the stoker hopper to that of the coal that reaches the retort to be burned. The experimental research on the relation of size to the performance of the coal is being actively continued. A publication of Bituminous Coal Research, Inc. presenting the data obtained on the performance of several sizes of four typical bituminous coals will appear shortly. Because of the early appearance of that publication, the present paper includes few numerical data. The purpose of this paper is to follow the coal from the hopper through the furnace with a discussion of the various actions that occur, in the hope that it will lead to a clearer understanding of the relation of the type of coal, the size of coal, and other characteristics, to the performance. The authors do not pretend to have obtained the answers to all the complex questions involved; many unanswered questions will be proposed on which future research work is planned.

Jan 1, 1938

By Martin A. Mayers

It has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimenta1 investigations of fuel-bed temperature1-4 have not been lacking, but the absence of any theoretical background has made it impossible to use the results of these tests as a basis for prediction, except in a very general may. A mathematical analysis", based on a somewhat simplified theory of the distribution of lieat in a fuel bed, lias recently been completed by the author. Even though numerical values of some of the coefficients are not known, the calculations result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calcu1ated. The uncertainty concerning the values of the coefficients referred to above is serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of the coefficients. For a more. extended discussion of the theory, see the A.S.M.E. paper5. Theory and Comparison with Experiment The theoretical analysis is similar to that used in the calculation of the stationary temperatures in a conducting solid in the classical theory of heat concluction. The fuel bed is pictured as a uniform, continuous, porous solid through the interstices of which air can be blown and ill which combustion can take place. The solid lias a finite thermal conductivity, so that heat may be transported in any direction, against the flow of air as well as in the same direction. While it is true that nothing

Jan 1, 1938

By Martin A. Mayers

It has long been recognized that it would be highly desirable to be able to predict the temperatures at various points in a burning fuel bed and their variations with changes of the properties of the fuel and the rate of air supply. Experimenta1 investigations of fuel-bed temperature1-4 have not been lacking, but the absence of any theoretical background has made it impossible to use the results of these tests as a basis for prediction, except in a very general may. A mathematical analysis", based on a somewhat simplified theory of the distribution of lieat in a fuel bed, lias recently been completed by the author. Even though numerical values of some of the coefficients are not known, the calculations result in some conclusions of general significance. Thus, for example, it appears that when the temperatures throughout the fuel bed can be calculated, the rate at which ignition of the fuel by underfeed action can be maintained can also be calcu1ated. The uncertainty concerning the values of the coefficients referred to above is serious limitation on the use of that method. The following paper presents a discussion of these coefficients and includes estimates of their values based on the data now available. A brief description of the theory on which the analysis is based, and some results of the calculations showing their degree of agreement with experimental results, are presented by way of introduction to the discussion of the coefficients. For a more. extended discussion of the theory, see the A.S.M.E. paper5. Theory and Comparison with Experiment The theoretical analysis is similar to that used in the calculation of the stationary temperatures in a conducting solid in the classical theory of heat concluction. The fuel bed is pictured as a uniform, continuous, porous solid through the interstices of which air can be blown and ill which combustion can take place. The solid lias a finite thermal conductivity, so that heat may be transported in any direction, against the flow of air as well as in the same direction. While it is true that nothing

Jan 1, 1938

By H. A. Wahl, J. M. Campbell

This study extends our information on solid-liquid slurries to the flow of sand in horizontal fractures. Inasmuch as this is basically an unsteady-state process, a comprehensive photographic study was undertaken in a 10-ft windowed cell to determine if the basic flow regimes described for steady-state flow in pipes applied to the subject process. Since the number of potential variables far exceeds the capacity of a single study, emphasis has been placed on the effects of sand concentration, oil viscosity and oil flow rate. The extensive photographic evidence obtained has proven very valuable in gaining an insight into the basic flow mechanisms. Being able to follow visually the flow characteristics that accompany the quantitative data is valuable in the application of the results. Although the use of dimensionless parameters was carefully investigated. it was found that the data obtained could be more easily, and as accurately, correlated by judicious use of the dimensional variables investigated. However, a study into the feasibility of scaling slurry flow was made in the event this technique is justified in future investigations. The data presented show that the pressure behavior observed in solids transport in pipes basically applies to slurry flow in horizontal fractures. The roles of the parameters are altered but a basic equivalence exists. The most significant correlating parameter was the oil viscosity (µo) and the bulk velocity of the slurry (vn), expressed as ''µv" product. The most significant correlation expresses the rate of advance of the sand as a function of the variables investigated. There are many practical ramifications of this phase of the investigation that should aid in better treatment design. Evaluation of sand advance rates provides a means of estimating sand placement efficiencies during a treatment and the resulting sand distribution in the fracture. The results show that sand placement efficiencies are low under typical treatment conditions. A brief description of the effects of overflushing is also included. INTRODUCTION The flow of sand-oil slurries in fractures is an area in which little basic knowledge is available. This stems to some degree from the fact that it is impossible to duplicate fractures at the surface. They occur in various shapes and sizes with an infinite combination of irregularities. Unfortunately, we can never "see" these fractures except in cores and by indirect means of measurement. In spite of this inherent difficulty, it is desirable to develop some basic concepts that will provide a better understanding of the sand transport mechanism. An insight into the problem is provided by investigations of fluid flow in rectangular conduits. Several studies on the flow of liquids in non-circular conduits1,13 show that a Reynolds number-Fanning friction factor relationship can be written if the hydraulic diameter is substituted for the regular diameter in a circular pipe. This hydraulic, or equivalent, diameter is taken as four times the cross-sectional area occupied by the flowing fluid divided by the wetted perimeter. Eq. 1 expresses an extension of this same work when applied to infinite parallel planes b distance apart.' Eq. 1 is a theoretical equation expressing the friction factor as a function of the Reynolds number for laminar single-phase fluid flow. This expression has been verified experimentally. The equivalent expression for a smooth circular conduit differs only in that the value of the constant is 16 instead of 24. Numerous studies have related friction losses to Reynolds number in both circular and non-circular conduits. These results are widely used and are not reviewed here. Huitt' investigated the effect of surface roughness on fluid flow in simulated fractures. He concluded that fluid flow in fractures may be treated similarly to fluid flow in circular conduits. This work, together with that of Nikuradse,' shows that surface roughness has no appreciative effect upon the resistance to flow in the viscous flow region. In the region of turbulent flow, surface roughness is a prominent factor. Hydraulic conveyance literature is another important source of information. Durand3 has attempted to organize systematically the variables involved in hydraulic-solid transport in pipes. He has classified the modes of flow into three types according to the size of the particles in the mixture— homogeneous mixtures, intermediary mixtures and heterogeneous mixtures. With the usual concentrations and flow rates used in hydraulic transportation, particles with diameters of less than 20 or 30 microns form eszentially homogeneous mixtures with water. The data show, however, that even small materials will tend to settle out under laminar flow conditions. Mixtures containing solids over 50 microns in diameter do not achieve total homogeneity even under turbulent flow conditions. Particles from 50 microns to 0.2 mm in diameter may be transported in fully suspended flow at normal transport velocities although the concentration in the vertical plane is not uniform. Above 2 mm in diameter solid materials are transported along the bottom of the conduit at a velocity substantially less than that of the liquid itself. Between 0.2 and 2 mm in diameter, the particles tend to be in a transition zone between heterogeneous suspended flow and deposit flow at normal hydraulic transport velocities. The sand sizes used in fracturing usually fall in this size range. It is interesting to note that the grain size range designated by Durand for this transition zone corresponds closely to the transition zone between

By G. St. J. Perrott

AN explosive of, balanced composition might be expected, on first consideration, to develop maximum propulsive strength.1 This hypothesis is based on the assumption that an excess of oxygen would act simply as an inert material with a consequent lowering of flame temperature, also that a deficiency of oxygen would tend toward incomplete reaction of the combustible materials, thereby preventing development of the full strength of the explosion. Actually, however, it can be shown both theoretically and experimentally that an explosive having a certain oxygen deficiency will develop the greatest propulsive strength. This fact has been known to the technical staffs of explosives manufacturers for many years, but it has not always been recognized by explosives engineers in the field. For example: There: is a fairly widespread opinion that the wrapper of a stick of dynamite is merely a container for the explosive and that it plays little if any part in the development of propulsive strength. Actually, it can be shown that the wrapper enters fairly completely into, the explosive reaction. In the case of most gelatin dynamites, a given weight of explosive from which the wrappers have been removed will develop considerably less strength than the same weight of explosive plus wrapper, in spite of the fact that the latter combination contains less weight of the actual explosive ingredient. It can also be shown that a cartridge 7/8 in. in diameter may be stronger, weight for

Jan 1, 1928

By P. Marier, T. R. Ingraham

When anhydrous cupric sulfate is heated in a stream of nonreactive gas, cupric oxysulfate is formed. When this reaction is complete, the cupric oxysulfate then decomposes to cupric oxide, which is the normal end product of reaction. The kinetics of each of these reactions has been studied using pellets prepared from finely divided cupric sulfate and from finely divided cupric oxysulfate. In each case, the reactant-product interface within the pellet is well-defined, and by normalizing the decrease in inter facial area with the weight fraction of the pellet decomposed it has been shown that the interface migrates into the pellet at a uniform rate at constant temperature. The activation energy estirnated for the decomposition of cupric sulfate is 57 ± 7 kcal per mole and that for cupric oxysulfate is 67 ± 8 kcal per mole. The rate of interfacial reaction is flow-sensitive, increasing with increasing flow of a sweep gas in the range from 50 to 2000 cu cm per min. The rate of decomposition is retarded by sulphur trioxide in the sweep gas. The relationship between sulfur trioxide Partial pressure and rate is consistent with the Langmuir Adsorption Isotherm governing the retention of sulfur trioxide in the interfacial layer. MOST of the work reported on the thermal decomposition of cupric sulfate and of cupric oxysulfate is related to the thermodynamics of the individual decompositions.'-4 No information is available on the rates of the individual reactions, on their activation energies, or on the effects of gas flow or of partial pressure of sulfur trioxide on the reaction rates. Some dubious conclusions based on relative reaction rates have been drawn from studies on the oxidation of sulfides. For example, on the basis of the products observed in a quenched system, it has been suggested5" that, when copper sulfide is roasted, the cupric oxide which is formed arises from the decomposition of either cupric sulfate or cupric oxysulfate. This is very difficult to reconcile with the thermodynamics of the C-S-O System,3 which support the probability that both cuprous oxide and cupric oxide precede cupric oxysulfate and cupric sulfate in the sequence of products formed during the oxidation of cuprous sulfide. In this paper the individual sulfate decomposition reactions will be examined and suggestions will be advanced for the mechanism of reaction. This will be based on the effects on reaction rate of changes in interfacial area, flow rate, and back-pressure of sulfur trioxide. EXPERIMENTAL Materials. The copper source material used in all experiments was Fisher Certified Reagent Grade anhydrous cupric sulfate, for which the following analysis was supplied by the manufacturer: chloride, 0.002 pct; alkalies and earths, 0.2 pct; insoluble, 0.002 pct; iron, 0.020 pct. Cupric oxysulfate was prepared by roasting cupric sulfate for 48 hr, with frequent rabbling, in an open tray in a muffle furnace maintained at 725°C. At this temperature, cupric sulfate develops about 0.16 atm pressure of combined sulfur trioxide, sulfur dioxide, and oxygen. Cupric oxysulfate develops only about 0.05 atm pressure, and is stable until

Jan 1, 1965

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author's reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

By Irving Cadoff, Richard Nolder

An analysis oj a series of samples of single -crystal silicon grown on sapphire shows that ,four distinct orientation relations exist. There are at least thirteen crystallographic planes which serve as substrates ,for epitaxial growth The model which assumes that silicon substitutes for aluminium and bonds with the oxygen atoms of the sapphire to form the first later for subsequent growth can account for the epitaxial geometry in all four cases. Multiplici-ties 01 specific orientations are found which are explained by the symmetry of both the sapphire and silicon crystal structures. It was reported in the previous paper' that single-crystal silicon films can be deposited on single-crystal a A1,03 (sapphire) with a wide variety of orientations. The silicon films, however, were found to deposit in only four different orientation relationships with respect to the sapphire substrate. The X-ray data have been analyzed to determine the plane and direction of atomic fit and an atomic model to account for the epitaxial relationships at the silicon-sapphire interface has been developed. These results are described in the present paper. EXPERIMENTAL The Laue X-ray data described in the previous paper were reduced to stereographic projections in a standard manner. These data were supplemented with X-ray reflection data obtained with -& E and A Full-Circle Goniometer (Electronics and Alloys, Inc.) mounted on a Phillips diffractometer unit. The silicon films were thin enough to result in characteristic reflections from the substrate as well as the silicon. The superimposed stereographic projections were analyzed to determine the orientation relationships. Ambiguities were resolved by referring to constructed models of various lattice planes for both silicon and sapphire. These lattice models were also used to develop the model for atom fit at the interface. DATA AND ANALYSIS 1) Crystal Structures. The crystallography of silico-n, which is of the diamond cubic class with a. = 5.4~, is straightforward. The sapphire structure is more complex and generally difficult to represent in pictorial form. It is of the rhombohedra1 class but usually referred to hexagonal axes. The transformation of indices between these two systems can lead to ambiguities which will have bearing on the analysis presented herein. Therefore, the basis used in this paper is described in the appendix. Referred to the hexagonal system, the parameters of sapphire are co = 12.95.&, a, = 4.75~, c/a = 2.73. All parameters are for room temperature. Figs. 1 and 2 illustrate schematically the hexagonal unit cell model of sapphire used for this analysis. The oxygen atoms are assumed to occupy positions in an idealized hexagonal array on basal planes. Their actual positions are in a slightly distorted hexagonal array. The aluminum-atom positions are scaled to their actual positions in the lattice with respect to the basal layers of oxygen atoms. It was found that an idealized model where the aluminum atoms are assumed to lie exactly at the octahedral interstices of the oxygen lattice, similar to that used by ~ronberg,' was not adequate for this study.

Jan 1, 1965

By Raymond M. Howe

Some time ago, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furrace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after.4 years' service so a steam-pressed lining- was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion. The fifth reply stated that the present "hard-burned" hand-made furnace lining had worn away very uniformly to the depth of only 5 in.

Jan 1, 1920

By Albert S. Trube

The purpose of this paper is to clarify the definition of compressibility and to present a uniform basis upon which instantaneous compressibilities of liquids and gases can be compared. The equations gaverning the instantaneous compressibilities of imperfect gases are derived and the concept of pseudo-reduced compressibility is introduced. Part of the data presented by Brown, Katz et a1 on compressibility factors for natural gases has been rearranged. A graph of pseudo-reduced compressibility vs pseudo-reduced pressure for various pseudo-reduced temperatures is presented. The need for additional work in relating the compressibilities of liquids and gases is discussed. This information should be of value to reservoir engineers in making non-steady state performance calculations in gas reservoirs. It should be of further use irz pointing the direction for additional research in the nature of liquid and gas compressibilities. INTRODUCTION With the increasing use of steady and non-steady state well and reservoir data, there is a corresponding increase in the importance of the various factors entering into such calculations. Increasing emphasis is being placed on the necessity for obtaining reasonably accurate estimates of the physical properties of the reservoir fluids well in advance of the more accurate laboratory data. One such factor is the isothermal coefficient of expansion of the media which are transmitting and attenuating the non-steady state pressure waves. The average isothermal coefficient of expansion, or "compressibility" is a complex function controlled by the physical properties of the formation and the fluids contained therein. The isothermal expansion coefficients for reservoir gases are usually quite variable, in many cases being highly-pressure sensitive. The coefficients for reservoir liquids tend to be pressure sensitive, but not nearly so much as reservoir gases. The coefficients for solids, usually expressed in terms of a "modulus of elasticity" are relatively insensitive to pressure variations within their elastic limits. For this reason, and also because many previous applications have been limited to rel- atively small pressure ranges, there has been a tendency to ignore the variable nature of isothermal expansion coefficients and treat them as constants. Also, the term "compressibility" by which these coefficients are generally designated is commonly confused with a similar term, z, used to define the deviation of an imperfect natural gas from the perfect gas laws. A clear distinction should be made at the outset between the term "compressibility", which is an isothermal coefficient of expansion of a substance, and the term "compressibility factor", z, which refers to the deviation of a gas from the perfect gas laws. Although the scope of this paper is limited to the compressibility of single phase natural gases, it is definitely related to the problem of accurately estimating the compressibilities of single phase hydrocarbon reservoir liquids, which will form the basis of a future presentation. BASIC PRINCIPLES The coefficient of isothermal compressibility of a substance, c, is usually determined from pressure-volume or pressure-length -measurements depending upon whether the substance is single phase gas, liquid, or solid. A convenient method for making such estimates for a finite change in pressure and volume at constant temperature is to use the well known equation V1-V2/V1 (p2 - p1) .....(1) Eq. 1 is negative because the volume of a confined substance decreases as the pressure is increased. In this case V1 > V2 and p2 > p1. This equation is useful in approximating the compressibilities of single phase gases and liquids undergoing small pressure changes. It is evident, however, that this equation is almost identical with the determination of Young's modulus of elasticity for solids. If the assumption is made that change in length is directly proportional to change in volume, as would very nearly be the case for a steel rod in tension within its elastic limit, then E5=-L1 (p2 - p1)/L1 - L2 .......(2) in which E. is the isothermal expansion coefficient, or Young's modulus of elasticity, for a solid. And further, for this special case L1 (p2 - p1)/L1 - L2 .......(3)

Jan 1, 1958

By Carville E. Sparks, Rollin Farmin

TRIAL installations of rock bolts, of the slit-rod- and-wedge type, were under way at several units of Day Mines, Inc., when Korean hostilities interrupted the already slow deliveries of steel bars to the Coeur d'Alene district. Factory-made bolts had not yet been put on the local market, so the program was halted for lack of supplies. Interest was revived by a visitor's description of wooden roof bolts. These were said to have been used briefly with apparent success in a coal mine, until apprehension voiced by the U. S. Bureau of Mines caused the practice to be suspended

Jan 9, 1953

By Arthur F. Colombo

The selective flocculation, desliming and flotation process developed by the U.S. Department of the Interior, Bureau of Mines, as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The application of the selective flocculation and cationic flotation process to three oxidized taconites from the western Mesabi Range in Minnesota is discussed. Data from the operation of a 408-kilogram-per-hour (900 lb/hr) pilot plant employing reclaimed water are summarized for the three types of oxidized taconites.

Jan 1, 1980