Search Documents

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By Robert H. Richards, Richard W. Lodge

A great deal of speculation, as well as actual experiment, has been devoted to ascertaining the changes in the materials (luring their descent in an iron blast-furnace, affecting (1) the chemical constitution, (2) the mechanical condition, and (3) the arrangement of the materials. With a view to throw some light upon the third question, we constructed a model and tried experiments which are here described. Our model is a vertical section of a furnace, with the lines of the Edgar Thomson furnace D of 1885 for the use of which we arc indebted to Mr. Gayley. The model is 40 inches high, and made to scale (1/2 inch equals 1 foot), and the horizontal section of the space through which the charge falls at any point in the descent is 11/2 in. x d, d being the diameter of the furnace at that place. We are unable to say just where the idea of making this model came from ; perhaps, partly from The Principles of the Manufacture of Iron, and Steel, 1884, I. Lowthian Bell, p. 124 ; partly, also, from

Jan 1, 1888

By J. F. Myers, S. D. Michaelson, F. C. Bond

This work was undertaken with the object of collecting plant data on rod milling, making laboratory tests on representative samples of the various ores, and arriving at a basis for comparing the relative efficiencies of different mills operating on widely different materials and under varying conditions. These efficiencies consider only power consumption and do not include the other elements of operating costs. The over-all economic efficiency may be quite different from the consumption efficiencies with which this paper is concerned. It is hoped that these collected data will be of value in indicating the most favorable conditions of rod-mill operation. Operating-plant data on 14 different installations from II plants throughout the United States and Canada were collected, and laboratory tests were made on samples of these ores. The plant rod mills were all operated wet, and either in open circuit or with circulating loads so small as to be negligible. Data were obtained on one roll-crushing operation at the Utah Copper Co., for comparison. The rolls were operated wet in closed circuit with 10-mesh vibrating screens, and with a high circulating load averaging about 600 pct. This particular roll operation can be considered as a model of efficiency. The collected plant data are necessarily incomplete in some instances. Each ore was assigned a code number, and the name and location corresponding to the code number are listed in Table I when permitted. The power data in every instance refer to motor input. Net power was reported by the operator for samples 1-30 and 1-45, and this was increased by 20 pct to compensate for motor losses and power factor. The plant rod-mill data are listed in Tables 2 and 3. In Table 2 the speeds are calculated on the basis of partly worn rod-mill liners 2 in. thick. Where D

Jan 1, 1949

By Ronald J. Roman

All mining and milling complexes can, within limits, operate at a variety of production rates. Factors of economic importance that are affected by production rates are costs per unit production, recovery, and product grade. Once the relationship between the production rate and cost is established, dynamic-programming techniques can define the optimum production schedule (i.e., the production schedule that maximizes the present worth of the operation) for the life of the deposit. In general, the optimum production rate is not constant for the life of the deposit, but declines gradually as the deposit is being exhausted.

Jan 1, 1972

By Peter J. Huck, Madan M. Singh

IIT Research Institute has investigated the potential of high pressure water jets for rapid rock excavation. During this study, an attempt was made to correlate the extent of breakage effected to the mechanical properties of rocks. Six rock types were used in these experiments and nine properties were determined for each rock variety. A regression equation using the two most significant rock properties and one jet parameter (pressure) was established. Although tests were conducted to specific pressures of 35, no minimum in the specific energy consumption was noted.

Jan 1, 1971

By Nobuhiro Takahashi

PROLOGUE The Yaguki mine, which is located near the southern end of the Tohoku region, Japan, near the coast of the Pacific Ocean, had had a long history as a copper mine, but had not been operated since 1925. About 30 years later it was reopened by Nittetsu Mining Company, and in 1958 a small flotation and magnetic separation plant, a so-called test plant, started production. The ball mill the author first met, a 8x4x4x7 ft tricone mill, called No.1 mill, had started running at that time. With his experience in initial, running of this mill he realized that the ball mill was not simply a preparatory process to flotation, but a determinant factor for flotation performance, an energy-consuming and costly process, and that its operation control was an important task in the plant (1). The working part of an operating ball mill is the ball load inside, whose properties govern the grinding performance. Its size distribution affects the efficiency greatly and the capacity is nearly proportional to its weight. When a ball mill operates for a long period of time with a constant and consistent addition of renewal balls, wear and renewal of balls are balanced, and an equilibrium ball load is formed. A stable equilibrium load is the primary requirement for a stable ball mill operation. However, renewal ball size would be the most influential factor affecting efficiency and capacity of operating ball mills. To improve efficiency, to increase capacity, or to get finer product, attempts to find out the optimum size assortment of renewal balls should be made. When re-

Jan 1, 1976

By Raja P. Upadhyay

An evaluation of the economics of mining the deep, thick oil shale deposits of the central portion of the Piceance Creek basin, Colorado, U.S.A. is presented in this paper. For the analysis, a modified large scale underground mining system developed by Cameron Engineers, Inc. and the Gas Combustion retorting process developed by the U.S. Bureau of Mines were used to determine capital investment and annual operating costs. A modified risk analysis computer program was then used to calculate DCFROI’s for various grades of oil shale and selling prices of partially refined shale oil. Sensitivity analyses were performed to quantify the affect of bonus bid payments, operating costs, capital investment, and all costs on DCFROI. In addition, a probabilistic evaluation was made to determine the risk involved in obtaining desired rates of return. Results of the economic evaluation indicate that for current selling prices of crude oil a high risk is involved in obtaining a DCFROI of 15%, unless only higher grades of oil shale are mined. However, mining only the higher grade oil shales, 125 l/mt (30 gpt) and above, would effectively reduce the potentially mineable resources by 90%. Risk can also be reduced through higher selling prices of shale oil. Sensitivity analyses indicate that the capital investment has a three times greater effect on required selling price than total operating costs.

Jan 1, 1977

By J. T. Norton, J. G. McMullin

The ternary system of gold-silver-copper is characterized by a solid solubility gap and a two phase region in which copper-poor and silver-poor phases coexist. At about 30 pct gold, the two phases become mutually soluble at temperatures below the melting temperature. As the gold content is increased, the solubility temperature of the alloys decreases until at about 80 pct gold, the two phases are soluble down to the lowest temperature at which the alloys will recrystallize. Although the general form of the two phase region is known, its boundaries do not seem to have been investigated extensively. In an X ray diffraction study, Masing and Kloiberl have outlined the boundaries of this two phase field at 400 and 750°C. Using only microscopic techniques, Pickus and Pickus2 determined a vertical section of the ternary diagram showing the 14 kt alloys (58.3 pct gold). These two reports are riot in complete agreement. It has been shown3 that some of the ternary alloys are susceptible to age hardening and that the hardening is caused by the separation of a homogeneous alloy into two phases at the aging temperature. While the gold-copper binary system is an outstanding example of super lattice formation, Hultgren4 has shown that a few per cent of silver added to gold-copper destroys the tendency for ordering. Because of the age hardening possibilities of these alloys, it seemed advisable to investigate the boundaries of the two phase field more in detail using an X ray diffraction method, so as to permit a better understanding of the aging phenomena and enable predictions as to the behavior of other alloys to be made. This is especially true for the 18 kt alloys (75.0 pct Au) at the lower temperatures since they are known to exhibit age hardening. Twelve ternary alloys were prepared having the compositions shown in Table 1 and graphically in Fig 1. The gold used was fine gold bars supplied by Handy and Harmon. The silver was a bar of high purity silver from the U. S. Bureau of Standards. The copper was a bar of vacuum-treated, high conductivity copper from the National Research Corporation. The pure metals in the form of powder were weighed out in proper proportions and melted in graphite in a high frequency induction vacuum furnace. They were heated to 1100°C and slowly cooled. The ingots were then removed from the crucible, inverted, returned to the crucible and remelted. This remelting procedure was intended to reduce segregation in the ingots. After remelting, the ingots were checked for weight loss. The weight loss in each ten gram ingot was held to less than 25 mg. The remelted ingots were cold rolled and then given a homogenizing heat treatment of 16 hr at 760°C to remove any remaining segregation. Powder specimens were prepared by cutting the ingots with a fine file, one half the required amount of powder being taken from each end of the ingots. When the X ray diffraction pattern showed any difference in lattice constant between the ends of the ingot, the ingot was remelted and given an additional homogenization treatment. All powder samples were sealed in evacuated pyrex tubes for heat treatment. Ordinary pyrex proved satisfactory for temperatures up to 650°C but above that temperature it was necessary to use a special high temperature pyrex glass. Annealing at temperatures below 500°C was done in a salt bath whereas for temperatures of 500°C and above an electric muffle furnace was used. In both furnaces the temperature control was ± 5°C. In all annealing treatments samples of cold worked powder were placed in a furnace which was already at temperature. In this manner the specimens recrystallized directly to the equilibrium structure for that temperature. Time at temperature was selected so as to allow complete recrystallization, but very little grain growth. Specimens were quenched from the annealing temperatures by breaking the pyrex tubes in cold water. X ray diffraction photograms were made of all the heat treated powders using copper radiation and a Phragmen

Jan 1, 1950

By James R. Stuart

AS the available remaining properties of iron ore reserves on the Mesabi Range are opened up for mining, the various properties located under lake beds are brought nearer an active status. The actual physical problems involved in stripping these properties do not act as a deterrent so much as the legal and political problems that are encountered. When it is proposed to destroy a natural lake that has been used by the public for many years, much local as well as state opposition may be encountered regarding its destruction. Public hearings must be held and some adverse publicity is likely to result. The ownership of the ore under the lake and the rights of the abutting property owners must be settled, and protection from damage caused by a disturbance in surface and subsurface drainage is likely to be demanded by property owners some distance from the proposed mine area. The Embarrass Mine, located near Biwabik, Minn., falls into this classification. A portion of the orebody lies under what was formerly Syracuse Lake, this body of water having been removed in the process of stripping the mine. An additional problem in the case of a meandered body of water is the establishment of a meander line that can be projected downward as mining progresses to form the basis for a satisfactory division between lake bed and upland ore shipments for royalty purposes. Fig. 1 illustrates the complications encountered in maintaining these divisions. A balance point was agreed upon in the center of the lake to make an equable division of lake bed ore to the abutting properties. The entire lake bed has since been adjudged the property of Minnesota. Lake Characteristics Lake bed stripping problems with which this paper is concerned necessarily are limited to a specific type of lake, namely the glacial lakes of the Lake Superior region. One characteristic common to these bodies of water is a deposit of fine black mud or silt on the bottom, frequently underlain by a layer of impervious blue clay. This is also true of the muskeg areas of the region, which present almost identical problems as lakes in stripping. The actual removal of the water and the lake bed material is a routine matter more or less standardized as to equipment, and the period of time required can be estimated easily on the basis of volume and capacity. More important than the foregoing is the execution of preliminary work, and above all, the timing involved. An account could be prepared based entirely on statistical and cost data which would give a very fair picture of the time required and cash outlay needed to effect the removal of a body of water preliminary to stripping the orebody. However, the real interest from the standpoint of the operator and the engineer who carry responsibility for completion of the job lies in the unexpected emergencies and the action of various materials involved in the stripping when the balance has been upset through diversion of water courses and the reduction of the lake level. Runoff and Drainage Lakes are located in natural basins that catch all the rain water and runoff water for a considerable area. Where a lake is involved having an inlet and outlet or a sizeable water course running through it, the drainage area may include a watershed covering many square miles. All available data then must be collected to supply a history extending over as many years for which information can be gathered on the flow of streams, annual rain and snowfall, and most important, the peak flows to be expected. Where the diversion of a stream around the stripping area is a part of the problem, this last factor is of great importance since it controls the cross-section to be selected for the diversion channel and the volume to be removed in its excavation, as well as affecting the hydraulic considerations to be met in the design of the completed channel. Characteristic material in the overburden found at the Embarrass Mine is illustrated in Fig. 2. Well Pumping Pumping from the well holes was started well in advance of the draining of the lake. Fig. 3 shows a gradual lowering of the water table with no noticeable fluctuations during the period in which the lake was being dewatered. Unfortunately, because of tight ground, a maximum flow to the wells was not maintained. This retarded the rate at which the water table was reduced so that in the course of stripping the excavation soon extended below the water table, and the great bulk of the pumping was handled from a system of sumps in the pit itself. Any dewatering program projected by prepumping from wells, a glorified well point system, would have to be started well in advance of the stripping to be of any great advantage. Preliminary drainage of the surface over the mine area is entirely apart from the actual elimination of the lake bed itself. Since the lake is what is called a perched water table because of the impervious character of the lake bottom, the adjoining surface may be dewatered below the surface of the existing lake and the flow will not be affected by the proximity of that body of water. This condition actually has been demonstrated through the establishment of a number of observation holes where a small churn drill was used to put down the holes and a 3-in. pipe was installed for taking water level

Jan 1, 1952

PRESENTATION of the 1922 Washington Award to Capt. Robert W. Hunt, honorary member and twice president of the Institute, was made at the annual dinner of the Western Society of Engineers, in Chicago, on June 18, 1923, in the presence of 250 mem-bers and guests. W. L. Abbott, Chairman of the Award Commission, when delivering the presentation address, said The life of the Govern-ment of this country, as the lives of governments are usually measured, is short, barely 150 years, but meas-ured by what it has accom-plished, this country has reached a venerable age. The first 75 years of our country's existence were necessarily preparatory to the greater developments which came in the second, and that last half of our country's existence is ex-ceeded, by ten years, by the span of life of our honored guest. "Very little iron and steel were produced in this coun-try until after the birth of Robert W. Hunt. And it was not until after 1860, when as a boy of 21 he joined his fortunes with those of the Cambria Iron Works, that the iron and steel business of the country really took root. After a year or two with the Cambria Works, he left a promising position to go into the army, where he served for four years. After the close of the war he returned to the iron works and qualified himself as a metallurgical chemist.

Jan 7, 1923

By A. Poll, J. E. Stantan, L. J. Jolley

THE basic problem in the generation of water gas from carbonaceous fuels and steam is the supply of the heat of reaction, and in general the source of this heat is the combustion of a further quantity of carbon with oxygen. Existing and proposed processes for complete gasification differ in the methods employed for transferring this heat to the fuel, and involve one or other of the following alternatives: 1. Use of a steam-oxygen mixture as the gasifying medium, so that the combustion and gasification reactions are combined. 2. Alternate passage of air and steam through a fixed bed, as in conventional water-gas production. 3. Cyclic passage of fluidized fuel through combustion and gasification zones. 4. Intense preheating of steam and of a portion of the gas made, and recirculation of this mixture through the fuel bed. 5. Supply of heat to the fuel bed through an externally heated wall. Except for the conventional water-gas process using large coke or low- volatile coal, only processes in the first group, operating with steam and oxygen, have proved practicable with fuels other than brown coals and lignites. A possible exception, which has not so far reached a commercial scale, is the moving-burden process developed by Imperial Chemical Indus- tries, Ltd. The cost of industrial oxygen is so high that its use can probably be justified only if it is attended by substantial savings in other directions; for instance, the use of cheap fuel. In the United Kingdom, no very cheap solid fuels are available, and it is unlikely that an oxygen-gasification process could compete economically with conventional production of blue water gas from coke. Hence particular interest attaches to all possibilities of making water gas without using oxygen, if any possible saving in fuel or other costs is involved. The cheapest and most abundant coals in the United Kingdom are the low-rank noncaking bituminous coals in small and ungraded sizes, typically those from the East Midlands coal field, and-fines of high ash content produced in coal-cleaning operations. A process capable of gasifying

Jan 1, 1953

Freeman, the English historian, said that he had learned from Macaulay "never to be afraid of using the same word or name over and over again if by that means anything could be added to clearness or force. Macaulay never goes. on, like some writers, talking about ' the former ' and 'the latter ', 'he ', 'she ', 'it), and 'they’, through clause after clause, while his reader has to look back to see which of several persons it is that is so darkly referred to". He might have learned also from Macaulay that a preposition makes a feeble ending for a serious statement. How often do you hear 'the former' and 'the latter' in conversation? Good conversation is a guide not to be disdained. When you must use 'the latter ', do not confuse it with 'the last '. Cheap labor, cheap fuel, and cheap transport are essential, the latter [last] being particularly important in base-metal mining. The apparatus may be used to determine such gases as hydrogen sulphide, chlorine, oxides of nitrogen and some others, as well as sulphur dioxide. In the case of the latter two, etc. The two last mentioned are "sulphur dioxide" and "some others". He should have stated which two, and he should have avoided that wretched phrase "in the case of ". Pinning may be partly prevented by use of chalk, oil, or turpentine. The latter [last] is beat. "Partly prevented" is a poor phrase. 'Prevented' is a word that does not lend itself readily to modification. He means ' checked ' or 'corrected '. These steps are necessary to produce the gas, crude oil, and ammonia, the latter [last] of which is in solution in the water obtained along with the oil.

Jan 1, 1931

By Robert L. Braun, Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides, chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 100° to 150°C. The rate of dissolution of chalcopyrite exposed to oxygen-saturated solutions becomes so rapid under these conditions that the rate of copper extraction becomes limited by the accessibility of chalcopyrite to the solutions. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, and size of ore particles. It is concluded that the high pressure and high temperature obtainable in a large ore mass broken by nuclear explosives promise the rapid and economic recovery of minerals not considered soluble by conventional in-situ leaching methods. The method should be broadly applicable to the kinds of deep deposits that must be depended on for future production and with minimum disruption of the environment.

Jan 1, 1974

By L. Eaton, A. W. Last, J. L. Stevens

COPPER ore from Kennecott Copper's Ray mine, about 60 miles southeast of Phoenix, Ariz., is concentrated at the company's mill at Hayden, some 18 miles south of the mine. The Hayden mill is currently treating 16,000 tons of ore per day by flotation, using raconite, a crude butyl xanthate, as a collector for the sulfide copper minerals and lime as a pyrite depressant.1 The ore contains significant amounts of nonsulfide copper minerals, but recovery of these values has been low. The Hayden mill is now being modified to provide for treatment of future ores by leach- precipitation-flotation (L-P-F). This modification, costing about $5 million, is expected to reduce the loss of nonsulfide copper values and improve overall copper recovery by an additional 2 lb per ton of ore.

Jan 11, 1957

By T. Egleston

THE ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, how¬ever, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattle-snake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings ; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

Jan 1, 1875

By SME

A regular feature of the December issue is the abstracts of graduate theses in the mineral industry field presented during the preceding year. The following abstracts were submitted for this second article in the series.

Jan 1, 1976

By T. L. Kesler

With only six small spodumene prospect pits, no detailed mapping, and no subsurface information in 1938, the Carolina lithium-pegmatite area now contains four mines among more than 25 properties on which exploratory work has been done. Even the open pit mine of Foote Mineral Co. described herein, from which ten million tons of ore and waste have been removed since 1952, was virgin ground when mapped in 1938-40 1. It has been a privilege to participate in the transition. In 1940, the spodumene pegmatites were known in a 25-mile belt (originally noted for tin prospecting) between Lincolnton, N. C. and Grover at the South Carolina line. Subsequently, Broadhurst 2 reported relatively small bodies northeast of Lincolnton near the Catawba County line. To the south, diamond drilling done in 1953 on the old Ross tin-mine property near Gaffney yielded pegmatite cores containing a few crystals of spodumene. This fact, not previously reported, suggests that some of the pyroxene in the Ross shaft as described by Sloan 3 may be spodumene.

Jan 9, 1961

By R. V. Vines, E. M. Wise

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940

By E. M. Wise, R. V. Vines

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940