Search Documents

By Albert Sauveur

The following propositions and corollaries are intended to present, as concisely as possible, some of the evidences gathered while studying the microstructure of steel. Each proposition is accompanied by photo-micrographs showing the structure of illustrative samples. But it must be understood that the special instances thus chosen for illustration are by no means the only ones on the examination of which the propositions are based. On the contrary, they have been taken almost at random among a great many, in some instances more than a hundred, similar cases. Proposition I. A slow and undisturbed cooling from a temperature x or higher produces crystallization. Plate L, Plate II., Fig. 1, and Plate V., Figs. 1, 2, 3 and 4 show the crystalline structure of several pieces of steel. Plate I. reveals this structure in the center of a slowly-cooled Bessemer ingot, 1.5 feet from the top. Plate II., Pig. 1, is from a small 2-in, square testingot of the same heat, slowly cooled. Plate V., Figs. 1, 2, 3 and 4 show the structure of different parts of steel rails. The original photographs were all magnified 70 diameters, and have been reduced in engraving to 63, or to 55 diameters, as shown in the plates. Proposition 11. Undisturbed cooling from an initial temperature lower than x is not accompanied by crystallization. Plate III., Fig. 5, shows the structure of a piece of rail-steel forged from a white heat until it had fallen to dull-red. The structure is almost amorphous. Practically no crystallization has taken place during the subsequent cooling. Corollary.—Pieces of steel finished at a temperature lower than x do not take a crystalline structure.

Jan 1, 1894

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in the discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in the smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently in the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of the joined pieces (base metal). The filler metal, solder or braze, is always of lower melting point than the base metal. Consequently with these processes there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Join¬ing operations carried out at temperatures above 500° C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used. Soldering Fluxes Even thoroughly cleaned and degreased, metal surfaces still possess tenacious oxide films which inhibit the soldering of the joint. The reactions which form these films increase with increasing temperature. The rate of oxide formation and the tenacity of the film varies with each base metal. Aluminum, magnesium, stainless and high alloy steels, aluminum and silicon bronzes when exposed to air form hard, adherent oxide films. These metals require highly active and corrosive fluxes to remove and prevent the reformation of oxide films during soldering. Metals such as copper and silver, on the contrary, form less tenacious films at a lower rate, so that mild fluxes are sufficient. Soldering fluxes must dissolve or remove oxides and promote rapid wetting and spreading of the solder. The flux removes the oxide film by loosening and floating it off into the main body of the flux. The oxide removal is often aided by the alloying of the solder with the base metal, undermining small areas of the oxide and detaching them (Anon., 1959). The flux coagulates and suspends the oxide particles which have been loosened. The flux forms a protective cover preventing the reformation of the oxides, permitting the spreading of the solder and the formation of a metallic bond between the solder and the base metal. Constituents of Soldering Fluxes: Soldering fluxes are commonly grouped into three categories: highly corrosive, intermediate, and noncorrosive. One normally would choose to use the least corrosive flux which will give satisfactory performance.

Jan 1, 1983

By C. Perez-Rosales

A statistical method for determining simultaneously some of the basic geometrical characteristics of porous media such as porsity, specific surface* mean pore width, mean grain thickness and absolute permeability is presented. The proposed method is characterized by its simplicity and the minimum amount of laboratory equipment that it requires. The experimental procedure used to evaluate the various geometrical characteristics is based 'pan the 'surface analysis Of a a In view of this fact the app1icability Of the method is limited to homogeneous and isotropic materials. INTRODUCTION The behavior of a fluid flowing through a porous medium depends, among other things, upon the internal geometry of the medium; hence the importance of developing efficient methods to determine the geometrical properties of porous materials. This paper describes a statistical method to determine simultaneously some of the basic geometrical properties of porous materials such as porosity, specific surface, mean pore width, mean grain thickness and absolute permeability. The mathematical formulation has been developed that the data required to calculate the various geometrical characteristics of a sample can be easily measured by analyzing a section of the sample with an evenly spaced grid. THEORY A simple way of obtaining information about the internal geometry of a porous material is to throw a point at random over a cross-section of a sample. l-Through this procedure the porosity can be detemined.l,2 By considering that the material is homogeneous and isotropic, and that the point is dropped many times, the porosity 4 is given by where N is the total number of times the point is thrown and n is he number of times the point falls within pore areas. Another simple manner of analyzing the structural characteristics of a porous material is to superimpose an arbitrarily long line on a cross-section so that its length is evenly distributed over the surface area. Through this procedure the porosity can also be determined. If L is the total length of the line, and 1 is the sum of the lengths of the line segments within void spaces, the porosity is given by 4 = —.1.............. (2) The advantage of this type of analysis is that geometrical characteristics other than porosity can be obtained. Thus, if c represents the number of intersections between the line and the perimeter of pores, it can be shown3 that the specific surface, defined as he surface area of pores per unit bulk volume, is given by To give a proper description of the internal geometry of a porous medium, it is necessary to define quantities that characterize the notions of pore size and grain size. Unfortunately, because of the complexity of porous materials, it is difficult to give exact geometrical definitions of what is meant by the ConCePtS of "poresl' and "grains", especially when dealing with consolidated materials. Never theless, one often talks about the "size of pores" and the "size of grains" without defining accurately the terms. A possible solution to this problem follows. Assume that an arbitrarily long line is placed on a section of a sample so that the line is evenly distributed over the surface area (see Fig. 1). 1n a system like this, each line segment within a void space will be, by definition, the pore width in a given location and direction. Consequently, if the

Jan 1, 1970

By John Chipman, Helen Towers

DEVELOPMENT of a simple radioactive tracer technique for measurement of the diffusion coefficient of calcium ion in liquid slag has already been reported. The investigation was of a preliminary nature designed to explore the possibilities of using radioactive isotopes and to establish a method, and no great accuracy was claimed for the results. It was shown, however, that Ca15 could be used successfully, and the values obtained for the diffusion coefficient appeared to be of the right order of magnitude. However, it was considered that a better technique could be devised for carrying out the diffusion. The experiments were, therefore, continued to find a more accurate method, to check the calcium results, and to extend the investigation to include measurements of the diffusion coefficient of silicon in the same slag. There were two flaws in the original technique. Convection was the cause of too many failures, and the interface between the two slags in the diffusion cell was curved rather than plane, probably due to a surface tension effect caused by the addition of the tracer Ca45 in the form of chloride. Two methods of overcoming these defects were tried. Since it was planned to study diffusion of the short-lived isotope Si"' also, the development of methods was restricted to those which gave promise of being reasonably rapid. Method 1—The principle was identical to that previously used with respect to the diffusion conditions, but there were three differences in technique. Temperature control was more rigid, the tracer was added to the slag as Ca45O rather than the chloride and, finally, an effort was made to translate to high temperatures the elegant method developed by Cohen and BruinV or bringing together the two liquid layers and beginning the diffusion. A master slag was melted in graphite, ground to a fine powder, and analyzed (38.5 pct Ca0-20.9 pct Al2O3-40.5 pct SiO2). The tracer was received as Ca45C12 in an aqueous solution of CaC12 + HC1. From this, calcium oxalate was precipitated, ignited to calcium oxide, and added as such to the slag to give an activity of approximately 5 µc per g. The mixture was then melted into the form of a cylinder 3/16 in. diam and about 1 in. long. A solution identical to the tracer solution without Ca45 was given exactly the same treatment. The resulting Ca40O was mixed with that slag which was to form the tracer-free half of the diffusion cell, and this was likewise melted into a cylinder of the same size. Slag cylinders, two with and two without Ca15, were set in graphite blocks as shown in Fig. 1, and the crucible was lowered into position in the fur-

Jan 1, 1958

By T. A. Klinefelter

Lightweight concrete aggregates are materials weighing less than the usual aggregates of sand, gravel, and crushed rock. Concretes made with sand and gravel or crushed rock weigh 145 to 150 lb per cu ft, compared with 50 to 90 lb per cu ft for concretes made with lightweight aggregate. The ultra-lightweight concretes weigh much less than 50 lb per cu ft. Lightweight aggregates may be natural or manufactured materials, or byproducts from other commercial operations. Natural materials include pumice and pumicite, tuffs, breccia, scoria, diatomite, and vegetable products, such as peat, straw, and sawdust. Manufactured materials include expanded perlite, vermiculite, slag, clay, shale, and slate. Byproducts include cinders, aircooled slags, and coke breeze. Concretes made with lightweight aggregate were used first in construction of commercial buildings, later in homes. Present usage is general in multistory and other building construction, such as bridge decks, barges, jet-plane runways, piers and other structures. The industry has grown remarkably in the last decade. General Considerations The particular use to which the concrete may be put determines the importance of the various properties of the aggregates employed. Any given type of aggregate, however, should be reasonably uniform in composition and properties. It should be suitably graded and maintain proper weights, insulation values, and adequate strength to prevent breakdowns in mixing. It should bond properly with the cement, be inert to chemical reactions with cement and steel, and resist weathering, moisture, insects, and fungi. Some properties of any given type of lightweight aggregate from different suppliers may vary considerably because of differences in the source of raw material and the method of treatment. This statement applies particularly to expanded clays, shales and slates. All lightweight concretes have higher absorption of moisture and lower thermal conductivity, lower compressive strength, as well as lower unit weight as compared with standard concretes made with sand, gravel or crushed rock. Excepting cinders, the cost of lightweight aggregates is usually higher. Grading and unit weight requirements are given in ASTM standards: C 330-53T, Lightweight Aggregates for Structural Concrete; C 331-53T, Lightweight Aggregates for Concrete Masonry Units; C 332-54T, Lightweight Aggregates for Insulating Concrete. The production of masonry units shows the growth of the use and types of lightweight aggregates. In 1947 the total number of lightweight block was 460,000,000 units in 8 by 8 by 16-in. equivalents. By 1954 this had increased to 950,000,000 units. Of the 1954 production, 27 pct was of manufactured types, 43 pct of cinders, and 30 pct of remaining types. Raw Materials Used as Lightweight Aggregates It was stated above that a variety of products both natural and manufactured are used as lightweight aggregates. It is easy to understand that a bulky material of low unit value cannot be transported far and still remain a low cost product. Hence the product used in a particular market depends upon the availability of the possible raw materials. Thus it is

Jan 1, 1960

By W. H. Howard

As the result of a series of analyses and volume determinations of gases discharged from the converters at the Garfield Smelting Co.'s smelter at Garfield, Utah, it was found that a considerable amount of lead fume was escaping from the stacks of the converter plant, and that if this lead could be recovered at a reasonable expense an attempt should be made to collect it. Two methods suggested themselves: (1) filtration through bags; (2) electrical precipitation of the condensed fume by a Cottrell plant. Filtration through Bags Tests were made in filtering converter gases through the ordinary woolen bags of lead-smelter bag houses to determine how long such material could withstand the corrosive action of the gases. While blowing on white metal only, the fabric was usually destroyed in 10 to 14 hr. In tests conducted in filtering gases when blowing on matte or slagging stage exclusively and when relatively considerable lead was being volatilizcd, bags in one instance lasted 60.5 hr. It therefore was evident that the Garfield converter gases did not contain in themselves sufficient neutralizing elements for the purpose of direct bag filtration, even during the slagging stage. Such results were more or less anticipated, but it was thus proved that under all conditions of blowing Garfield mattes a very considerable amount of neutralizing agent, zinc oxide or lime, or both combined, as in the Sprague process, would be required to render bag filtration possible. Again, owing to the constantly changing quantities of SO3 from a given battery of converters, depending on the number blowing at a given time and on the stages of the blow, it would be practically impossible to feed automatically the required amount of neutralizer. In order to safeguard the bags sufficient neutralizer would have to be continuously added to meet the maximum SO3 output, thus wasting neutralizers and giving an undesirably diluted final product. Such a condition is entirely different

Jan 1, 1915

By D. A. Sangrey, D. Marcus, S. A. Miller

A methodology was developed wherein the increase in compressive strength, mineralogical changes, and pore water composition were studied simultaneously as a function of moisturized spent shale curing time. From these results the relationship between the nature of cementation process and the composition of pore water was established. Heavy metals were entrapped in the cementing constituents and the pore water became mainly a solution of alkaline sulfates. The specific data are applicable only to the material studied. But the methodology and general conclusions are useful for evaluating the environmental factors in spent shale disposal and expected leachates composition.

Jan 1, 1986

By J. F. Myers, S. D. Michaelson, F. C. Bond

THIS work was undertaken with the object of collecting plant data on rod milling, making laboratory tests on representative samples of the various ores, and arriving at a basis for comparing the relative efficiencies of different mills operating on widely different materials and under varying conditions. These efficiencies consider only power consumption and do not include the other elements of operating costs. The over-all economic efficiency may be quite different from the consumption efficiencies with which this paper is concerned. It is hoped that these collected data will be of value in indicating the most favorable conditions of rod-mill operation. Operating-plant data on 14 different installations from 11 plants throughout the United States and Canada were collected, and laboratory tests were made on samples of these ores. The plant rod mills were all operated wet, and either in open circuit or with circulating loads so small as to be negligible. Data were obtained on one roll-crushing operation at the Utah Copper Co., for comparison. The rolls were operated wet in closed circuit with 10-mesh vibrating screens, and with a high circulating load averaging about 600 pct. This particular roll operation can be considered as a model of efficiency. The collected plant data are necessarily incomplete in some instances. Each ore was assigned a code number, and the name and location corresponding to the code number are listed in Table I when permitted. [ ] The power data in every instance refer to motor input. Net power was reported by the operator for samples I-39 and I-45, and this was increased by 20 pct to compensate for motor losses and power factor. The plant rod-mill data are listed in Tables 2 and 3. In Table 2 the speeds are calculated on the basis of partly worn rod-mill liners 2 in. thick. Where D

Jan 1, 1947

For some years MINING ENGINEERING has published abstracts of the articles appearing in each issue and also of the Transactions papers published in the Quarterly. Beginning this month, a list of key words is being given with each abstract as an aid to indexing the articles for ease in retrieving them when they are needed. The value of a home or office system of indexing and retrieving technical articles is hard to over-estimate. How often is it that a technical problem comes up and someone says: "Oh yes, I've read something about that." Many hours can be expended tracing down that nebulous source. A modest indexing and retrieval system will save those tedious hours, and the person who is able to produce technical documents when they are needed will achieve an enviable status for being on the ball.

Jan 1, 1964

By C. B. Gillson, Henry Fay

For several years past, investigations on the chemistry of tellurium have been carried on in the laboratory of this institution. The methods of preparation of pure telluriumf and the estimation of tellurium‡ have been studied, and an attempt to determine the atomic weight of tellurium is now in progress. All these problems had been investigated, however, along purely theoretical lines; and it was thought desirable to study the more practical application of the metal, which can now be had in considerable quantities as a waste product in the refining of copper-ores. In its physical and chemical properties tellurium is very similar to antimony, and it was thought

Jan 1, 1902

By Richard Pearce

IN looking around me for some subject on which to frame an address for this meeting, it has occurred to me that some results of observation and investigation, in regard to the varied conditions under which gold is found, may possibly prove of interest. The subject is one which frequently crops up in discussions at our meetings, but there is always an immense amount of uncertainty expressed as to the actual condition in which the gold exists in any particular ore. It follows, therefore, that any light which might be shed on this rather complex subject, would be of value to science and of service to mining and metallurgical practice. In some investigations which I have, from time to time, been led to make, for the purpose of determining to what extent an ore might be concentrated, I have been astonished at the very varied and apparently inexplicable results encountered, and have been naturally led to inquire into the causes for such seeming inconsistency. The mines of Gilpin county, Colorado, where gold was first discovered in that State, furnish an infinite variety of examples of its occurrence, and it was here that difficulties first presented themselves to the Colorado miners, in the sudden transition from what is called " free-milling gold-ore " to an ore characterized by properties which make the ordinary treatment by amalgamation stamp-mills utterly impracticable. So long as mining was limited to what might be called the zone of oxidation in the veins, just so long might amalgamation be conducted without difficulty; but directly the miner reached a point beyond the influence of the oxidizing power of the surface waters, the gold resisted all attempts at amalgamation, and recourse • was had to smelting.

Jan 1, 1890

By Arthur Gray

THE thermal analysis of a metal or alloy is ordinarily made with the aid of heating and cooling curves, in which transitions are indicated by the rapid changes in curvature that accompany .changes in the rate of heat absorption or evolution. Analysis by the method that depends on the change in thermal expansivity is not customary, partly, at least, because of the difficulties involved in making the necessary measurements. However, under certain circumstances, the dilatometric method of analysis may possess advantages over the thermometric method that will justify the additional trouble required. The addition of 1 per cent. of zinc to an alloy has been found to produce, upon the volume changes that take place during transition, effects that suggest the possibility of using the dilatometric method of thermal analysis as a rather sensitive means of obtaining chemical information. Although the illustrations presented in this paper are drawn from data obtained during an investigation of dental amalgams, similar phenomena can doubtless be observed with other alloys. Some of the results found during an investigation made in 19171 have been confirmed by data on the thermal expansivity of amalgams published by Souder and Peters of the Bureau of Standards in reporting tests of dental materials.2 Although the Bureau of. Standards made experiments for the purpose of discovering effects of including zinc as one of the constituents of a dental alloy-a matter much discussed in dental literature but without the presentation of reliable experimental evidence to support the views of ;either side-the reports of the test made by the Bureau give the impression that certain striking phenomena associated with the presence of zinc were not noticed. Among such phenomena are those connected with the conditions that determine whether or not a specimen of amalgam becomes covered with droplets from which crystals develop.

Jan 9, 1920

By Ben L. Seegmiller

Localized open pit slope failure was avoided as an apparent result of a practical rock mechanics program conducted at the Twin Buttes copper operation. The key to the program was the application of cable bolting, a technique that artificially supports open pit slopes using properly installed post-tensioned cables. As a result of the research and testing program, extensions of the cable bolting principal became significantly apparent. • The economics of artificial stabilization appear to be overwhelmingly favorable, and • Best practical applications are "final" pit slopes, slopes beneath permanent structures and potentially slope failing areas. Success of this research is manifested by the fact that similar stabilization systems are presently under consideration for Twin Buttes as well as other open pit operations.

Jan 12, 1974

By A. T. Tye

REGARDING the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."' L. O. Howard notes that "Perhaps the outstanding example so far published of improvements in results through the use of selective flotation is that at Cananea, Mexico." The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter. There are probably plants at which a better preferential separation is being made than at Cananea. Many ores contain barren iron pyrite which, when depressed, does not carry copper into the tailing. Some concentrators use clean uncontaminated water for milling and in others the ore is ground much finer than at Cananea. All of these items are concerned in perfect separation. The details of preferential flotation at Cananea, therefore, are not presented on account of the perfection of the

Jan 1, 1928

By C. F. Cornell, Henderson, A. F. Dunyon, D. A. Dahlstrom

IN processing magnetic taconites several steps of crushing, grinding, classification, and magnetic separation are required to produce a 60+ pct Fe concentrate. Usually the final concentrate is in a slurry form of 55 to 70 pct solids by weight and is further characterized by a particle size of 60+ pct -325 mesh. In taconite plants already completed or under construction the conventional method used to obtain pellets suitable for blast furnaces is to filter the concentrate slurry, ball the filter cake, and then harden the green pellets in a traveling grate or in a vertical shaft furnace. Large tonnages must be handled in minimum floor space, with reduced maintenance and lowest possible operating cost. Filtration must therefore achieve two objectives: 1) high filtration rate-in terms of pounds of dry solids per hour per square foot of filtration area-at a low filtrate solids concentration, and 2) a filter cake moisture that will always permit efficient balling within the normal fluctuations of plant operating conditions. If moisture contents are too high, balling may be impossible or result in a mushy ball without enough green strength for the firing operation.

Jan 3, 1957

IT is necessary that all men who wish to bring things to a certain end should think of the agents needed to attain this. Now whichever one of the above processes you wish to use you must consider the nature of the material and see whether it is disposed to render what you wish to extract. Then you must see whether you have the other agents sufficiently powerful and proportioned to attain this result, for if the things were not in harmony your work would be vain and very laborious. Therefore, if you should wish to make waters or oils by way of distilla-

Jan 1, 1942

By J. J. K. Daemen, C. Fairhurst

Introduction The stress field around a supported tunnel can be considered as being composed of: i) the virgin (pre-mining) stress in the rock ii) the (elastic) change in this stress field caused by creating the opening iii) the (time-dependent ) change in the stress field produced by (i) and (ii) as a section of the rock breaks up iv) the (time-dependent) influence of the stress build-up in the support. Several authors have examined the conditions necessary to produce static equilibrium between the support, the rock, and the regional (in-situ) stress field. The analysis used by Labasse (1) is typical. Consider a circular tunnel radius R in a hydrostatic stress field (P), and a radial pressure pi exerted by the support. According to Labasse, the radius ‘b’ to which the rock will break* for a given support pressure, pi, can be calculated from: - the equilibrium equation: [ ] As a zone of broken rock develops around the opening, the stress circle for a point on the elastic-broken rock boundary moves to the right in the Mohr diagram until the radial stress in the broken zone s equal to the radial stress in the elastic zone.

Jan 1, 1971

By Evangelo Agelopas

Steelmaking operators are familiar with the costs involved when ingot molds must be scrapped prematurely because of the failure of a stripping or turning lug. Some mold sizes can be expected to produce one hundred or more ingots per mold before normal wear causes the mold to become unserviceable. Therefore, the failure of lugs at less than the average life for that mold size represents a sharp increase in terms of mold cost per ingot ton produced. To combat these wasteful and costly occurrences, it was determined that an efficient method of replacing lugs should be developed to extend the life of molds which are otherwise in good condition. The purpose of this paper is to describe a lug welding method which has proved effective and economical. This method is known as the Oxygen and Mapp Process.

Jan 1, 1972

By Lawrence F. Schubert

Instrumentation is not a stranger to the minerals processing industry. In fact, very few plants now exist that haven't to one extent or another adapted operations to instrumentation. But with the rapid growth of such controls has come the need for effective departments composed of men trained to maintain and repair the instruments; here is where many firms fall short. The importance of the role an instrument department should play is underscored by the omnipotent effects which instruments often exert over an operation. Reserve Mining Co. is an example: while instrumentation at this taconite plant represents approximately 2% of the process equipment cost, a breakdown of instruments may result in the ineffective use (or complete shut-down) of the other 98% of plant investment.

Jan 7, 1966

By J. L. Thompson

There are two basic forms of the LPG-slug process: the gas driven and the water driven. The pressure required for miscibility between gas and LPG prohibits the use of the gas-driven LPG process in shallow reservoirs. The water-driven LPG slug process normally exhibits good sweep efficiency. However, displacement of the LPG by water is poor. An improvement in this process appears possible by injecting a slug of carbon dioxide between the LPG slug and the water drive. Laboratory experiments were conducted in homogeneous linear systems to determine the effect of pressure on the various displacement zones. In the carbon dioxide-LPG displacement zone, the effect of pressure on the displacement efficiency is negligible above the miscibility pressure. However, the displacement efficiency decreases linearly with decreasing pressure below the miscibility pressure. With water displacing carbon dioxide, it was found that the recovery of carbon dioxide after water breakthrough can be predicted from its solubility in water. A displacement test was conducted with LPG and carbon dioxide slugs large enough to avoid interference between the oil-LPG, LPG - carbon dioxide and carbon dioxide - water displacement zones. Under these conditions, essentially complete oil and LPG recovery was obtained. However, a substantial amount of carbon dioxide was left in the core at water breakthrough. INTRODUCTION It has been shown in homogeneous linear systems that essentially complete oil recovery can be obtained by displacement with a miscible fluid such as LPG. Economic considerations dictate that the valuable LPG also be recovered. Methods proposed for recovering the LPG include (1) displacement with natural gas at a pressure high enough to make the two fluids miscible1 (the disadvantage of this method is that the required pressure of about 1,500 psi is too high for shallow reservoirs) and (2) displacement of the LPG with water2 (principal disadvantage is that a large amount of LPG remains in the formation because of poor displacement efficiency). This paper treats an improvement in the water-driven LPG slug process3,4 where carbon dioxide is injected between the LPG and water. Carbon dioxide is completely or at least partially miscible with propane and soluble in water; thus, displacement efficiency is improved at both ends of the carbon dioxide slug. To minimize effects of other variables, all experiments were conducted in linear core systems. GENERAL PROCESS DESCRIPTION The displacements of propane by carbon dioxide and carbon dioxide by water are considered separately, assuming enough of each is injected to prevent mutual interference. Displacement descriptions are confined only to the part of the pore volume containing mobile fluids unless otherwise specified. The schematic representation is given in Fig. 1. Starting at the producing well, a zone containing only oil is followed by a zone containing a single-phase mixture of propane and oil. The concentration of propane increases in the direction of the injection well and ultimately grades to pure propane. Then follows a zone containing a mixture of propane and carbon dioxide in continuously varying proportions until 100 percent carbon dioxide is reached. In this zone, the concentration of carbon dioxide in the immobile water phase also varies from zero to full saturation. Whether the displacement of propane by carbon dioxide is of complete or partial miscibility depends on pressure and temperature (Fig. 2). If the horizontal line representing the prevailing pressure intercepts the boundary curves of the phase envelopes for the prevailing temperature (i.e., if the pressure is lower than the critical