Search Documents

By J. O. Scott

Transient pressure behavior of wells intersected by a single vertical fracture has been examined by means of a heat pow analogy. Results are correlated in terms of dimensionless pressure change and dimensionless transient time. The resulting curves are found to lie between the dimensionless curves for a cylindrical well and a line source when effective well radius is expressed as one-fourth of the total fracture length. Results are also shown for various degrees of afterflow. Use of the curves provides a means of determining reservoir permeability, wellbore radius, and thereby fracture length, even when the final slope of the transient curve is not obtained. Superposition of curves may be used to confirm existence of vertical fractures in the reservoir adjacent to the well or to indicate a damaged zone on the fracture face. INTRODUCTION Hydraulic fracturing has become a standard well completion practice for the purpose of increasing flow. Results are normally gauged in terms of some sort of "stabilized" flow rate established before and after the treatment. This procedure may be misleading because pressures in or around the well do not become "stabilized" during the test period. Transient pressure tests on fractured wells can overcome the objections to stabilized flow tests by indicating when a stable pressure gradient is reached. In addition, the transient pressure tests can be used to determine formation flow capacity and effective wellbore radius. The effective wellbore radius may be used as a measure of the success of the fracturing operation. The slope and position of the transient pressure-log time curve may be used to determine the flow capacity and wellbore size after sufficient lapse of time so that the pressure gradient in the vicinity of the fractures becomes constant. However, in tight reservoirs or in short tests this condition may not be reached. Presence of the fractures in tight reservoirs may cause a constantly increasing slope to the transient pressure curve. If this slope is picked too soon, formation flow capacity will appear high and the fracture size will appear too small. This paper is intended to clarify the early transient behavior of vertically fractured wells. It shows how formation flow capacity and wellbore size can be determined even though the maximum slope of the transient pressure curve is not obtained during the test. Development of the techniques of transient pressure analysis for wells has been summarized by Perrine.' He reviews the various definitions of wellbore effects such as skin effect, productivity ratio, damage factor and condition ratio. In the present paper, use of these terms is avoided by defining an effective wellbore size. For the fractured well this effective wellbore size is larger than the actual wellbore. Assumptions made are constant flow rate at the well, constant fluid compressibility, constant fluid mobility and uniform porosity and formation thickness. From the basic differential equations of flow, two different solutions may be obtained. The first, the line source solution, is commonly used in transient pressure analysis.' It expresses the change in pressure at any radius due to withdrawal or injection of fluid at the line source from an infinite reservoir at uniform initial pressure. This equation, in oil field units: is

By J. Amanat, H. J. Siriwardane

A numerical procedure based on nonlinear finite element analysis has been developed for predicting subsidence profile over longwall mine panels. The developed procedure has been verified by comparing predictions with published field observations at several mine panels. This paper presents certain aspects of predicting subsidence profile over mine panels located in hilly terrain. Analysis of four such cases are presented herein.

Jan 1, 1984

By G. W. P. Rengstorff, H. B. Goodwin

A method is described for purifying iron in batches of 150 Ib or more. Oxygen, carbon, nitrogen, and sulphur are removed from flakes of electrolytic iron by treatment in wet and then dry hydrogen. A special consumable-electrode arc furnace is used to remove hydrogen and to melt the flakes into ingots. A LTHOUGH iron and steel have been made and used for hundreds of years, there are still wide gaps in the knowledge of these metals. One reason for this is that the true properties of the base metal, iron, are not well known, simply because really pure iron has never been readily available for research purposes. Commercial iron, and even the "pure" irons which are readily available, are really complex alloys of iron with oxygen, nitrogen, hydrogen, carbon, sulphur, silicon, and other elements. With such materials, it has not been possible to prepare steels and other iron-base alloys in which all elements are present in exactly controlled amounts. It is an almost impossible task to determine the separate effects of each element or the intereffects of several elements unless alloys can be prepared containing only the desired elements. The ability to make controlled alloys of low impurity content is of far more than academic interest. It will assist in the study of such practical problems as the brittle failure of ship hulls or high pressure gas pipelines, determination of the factors which affect the deep-drawing properties of steels, the improvement of magnetic and electrical properties, the phenomenon of aging, and many others. In 1949, the American Iron and Steel Institute asked Battelle Memorial Institute to prepare high purity iron on a larger scale than had been attempted up to that time. The work was directed toward the preparation of iron as low as possible in carbon, oxygen, nitrogen, hydrogen, and sulphur because these are the contaminating elements of major interest in many research investigations on iron-base alloys. The initial goal was to prepare iron with not more than a few thousandths of one percent of each of these impurities. The purpose was to set up a "bank" of high purity iron on which researchers could draw when a supply was needed and which could be replenished from time to time as the stock became depleted. Of several possible purification methods, heating in hydrogen was selected as the most promising for the removal of both carbon and oxygen from solid iron. Metallic impurities are not removed by hydrogen. Electrolytic iron was chosen as a starting material because it is the most readily available form of iron low in metallic impurities. Decarburization and desulphurization were obtained by annealing in wet hydrogen at relatively low temperatures. The optimum temperature, as found by previous investigators,' is about 1400°F. This treatment also removes nitrogen. Deoxidation is favored by dry hydrogen and higher temperature. There is evidence from previous work that an anneal at 2200°F in dry hydrogen will deoxidize the iron, reduce the nitrogen content, and reduce the sulphur content. These facts suggested the use of a two-stage process: treatment in wet hydrogen followed by treatment in dry hydrogen. To carry out the purification process in a reasonable time, it was necessary that the iron be in thin pieces. Flakes of electrolytic iron were used. Because most research requires that the iron be in massive form, it was nccessary to melt the purified iron to consolidate it into large pieces. For this work, it was decided to prepare ingots weighing at least 15 lb by using a cold hearth arc-melting process in which the iron was melted in an inert atmosphere of argon or helium. This method of melting was selected because the water-cooled copper crucible is not wet by the iron and does not contaminate it as a refractory crucible would. Because the crucible is also the ingot mold, contamination from mold materials was also eliminated. Contamination from electrodes was avoided by making them from purified electrolytic iron. The melting procedure finally developed was an adaptation of the Kellogg electric ingot process.' Two batches of purified iron weighing about 100 Ib each in ingot form were prepared with analyses as shown in Table I. The remainder of this paper describes the procedures in more detail. In general, the process con-

Jan 1, 1956

By Morris Muskat

ANALYTICAL calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/3 in., and to approximately one half for a perforation radius of 1/4 in,, regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings.

Jan 1, 1942

By Charles Austin

IT has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A, critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publications1,2 have shown that the factors controlling graphitization below the A, are different from those operating above the A, inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemi-cal analyses. Many years ago it was recorded' that the rate of graphitization at subeutectoid tem-perature is not a maximum just below the A, critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is im-possible to spheroidize certain steels in the temperature range of 650° to 710°C. with-out the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A, (720°°C,) these same steels may be completely sphe-roidized at constant temperature. In previous studies1,2,4 on 1 per cent plain carbon steels graphitization was en-countered during prolonged tempering. The limited number of steels studied did not provide sufficient data to permit adequate study of the factors controlling this graphi-tization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, fur-nished by four steel companies, who also supplied information regarding the history of manufacture.

Jan 1, 1940

By Frederick N. Rhines

BECAUSE of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding 'their occurrence, even though the fundamental mechanisms involved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpret the next. It is the purpose of the present paper to present, by means of examples drawn from practice, a brief survey, of the ways in which gas-metal diffusion serves and obstructs the purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with but brief mention of parallel cases. THE NATURE OF GAS-METAL DIFFUSION The term "gas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to- regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. No element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By Nicholas J. Grant, John Chipman

A full understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization;the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag—i.e., equilibrium conditions—and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck:20 V radio = % CaO/%SiO, Körber and Oelsen's _ % CaO'. 100/% CaO + % SiO2 where (%CaO') = % CaO- 1.18% P2O5. Herty's B ratio = % CaO - (0.93 . % SO2) - (1.18% P205) Among others there appear the following: 20 References are at the end of the paper.

Jan 1, 1947

By J. N. Breston, R. V. Hughes

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By R. V. Hughes, J. N. Breston

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20's before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By E. H. Lancaster, M. E. Mitchell

A MUD-conditioning program found to be very effective for drilling and completion operations on routine field wells requiring relatively short drilling time involves a moderate alkaline-tannate-bentonite treatment resulting in an ultimate filtration rate of 10.0 cc or less (API test). Mud weight schedules are planned from pressure information on completed wells in producing reservoirs and drill-stem test data obtained on other zones not being produced at present. In general, terminal mud viscosities average 45 sec (Marsh). This value has been found to be sufficient to remove cuttings from the well bore on the average well, with the slush pumps in general use on the rigs. On field wells requiring drilling times in excess of approximately 30 days, an alkaline-tannate-lime-bentonite treatment has been effective in maintaining desirable viscosities and filtration rates with a substantial reduction in chemical costs. This system has shown particular advantage on heavily weighted muds and those with abnormal flow-line temperatures. For the most part, the chemical treatment utilized in wildcat drilling follows closely the program used on field wells, depending on depth and duration of drilling operations. Wildcat mud programs are planned from information available from various geologic and operational sources, taking into consideration the possibility of encountering mud problems of a special nature in the wildcat area. Careful planning of wildcat mud pro- grams has proved to have definite value in avoiding most serious mud problems. An analysis and recommended treatment are presented on several special. mud problems which have been encountered in the area in the past. Those problems discussed are lost circulation, blowouts, sloughing shale, excessive chloride contamination, sulphate contamination, and prevention and correction of cement contamination. Introduction Drilling-mud control in the Southwest Texas area, in general, does not involve the multiplicity of problems encountered in other coastal areas. For instance, it is rare that a mixture of problems such as lost circulation, abnormal pressure, severe sloughing shale, and others, occurs on one well within close enough limits in vertical depth not to be taken care of by a sensible casing program, together with a relatively clear-cut mud program. There are conditions such as the fairly widespread occurrence of abnormal pressure in the lower Frio and Vicksburg zones, and the tendency for sloughing shale in the Jackson section which make for rather expensive mud control. However, the availability of fairly accurate geologic and operational information makes possible a reasonable degree of standardization on mud treatment over a relatively large area. It may be said that, over most of this area where drilling is currently in progress, the natural mud made is very poor in quality, but responds readily to moderate chemical treatment to yield very good wall-building characteristics. AS far as field development drilling is concerned, the mud engineer's principal job, once the routine treatment best

Jan 1, 1949

By H. A. Shaw, H. G. G. Whitton

This paper describes the use of the electric-arc furnace for the production of tough-pitch, horizontal cast copper shapes and the production of copper anodes from tank house anode scrap. This installation is the only one of its kind in the United States. SINCE the initial use of electric-arc furnaces for refined copper melting on a commercial scale at Copper Cliff in 1936, this type of melting has been of extreme interest to everyone in any way connected with copper casting and fabricating. Early in 1948, Kennecott Copper Corp. decided to build an electrolytic copper refinery at Garfield, Utah. One of the major decisions to be made at that time was the type of furnace to be used for melting cathodes for casting into refined copper shapes and for melting anode scrap for the production of anodes. Based on the results obtained from arc furnaces by the Tnternational Nickel Co. of Canada, at Copper Cliff, and by the American Smelting and Refining Co., at Baltimore, coupled with certain important economic factors such as having an adequate amount of relatively cheap power available at the Magna Central Power Plant, high cost of poles and oil in the Salt Lake District, and the lack of natural gas at that time, the final decision was to install electric-arc furnaces rather than the standard type of rever-beratory furnaces. Experience has shown certain parts of the original installation to have been inadequate or in need of modification. Although the present status of arc-furnace melting at the Utah Refinery is far from perfect, nevertheless substantial progress has been made. At the Utah refinery, copper is melted in three 15-ft diam, size "M" Lectromelt furnaces, two of which are used for melting cathodes and one for remelting anode scrap. Each furnace is energized from a 13,800-225 v, 3-phase, 60-cycle, 6000-kva (at 40°C rise) oil-immersed water-cooled transformer. Auxiliary equipment for each refined copper furnace includes a charging machine, launders, ladle, 40 ft diam Walker-type casting wheel, bosh, and inspection conveyor. The anode furnace differs in that it is charged by hand from an elevated platform and the anodes are picked off the 24-ft diam casting wheel by a takeoff hoist and loaded directly into specially designed trailers, Figs. 1 and 2. Electrical Equipment Electric power to operate the arc furnaces is generated at the Kennecott-owned Magna Central Power Station two miles distant and transmitted to the Refinery outdoor substation at 44,000 v. At this point it is stepped down to 13,800 v and carried through concrete-lined underground tunnels to the switchgear and then to the primary side of the furnace transformers. The power is conducted from the Y-connected secondary bus bars of the transformer to the electrode arms by means of 22 flexible copper cable conductors per phase. Each cable has a cross-sectional area of 1,750,000 circular mils, giving a total area of 38,500,000 circular mils per phase. The power is carried from these cables to the three individual electrode holders by means of water-cooled copper bus tubing. The electrode clamps are incorporated in the electrode holders and are released by air pressure working against a spring in the clamp control cylinder. The movement of the electrode arms is either automatic or manual. The automatic control is used during melting and is regulated by three Westing-

Jan 1, 1954

By R. W. Jenkins

TRACKLESS equipment is being used by the Coplay Cement Manufacturing Co. to develop a folded limestone deposit economically and safely with inexperienced men. Cost and quality of development stone results in a saving when it is used in- stead of outside sources of limestone. This favorable cost has been attained by following a methods development and training program described in this paper. It is expected that further savings in favor of the mined stone will be made when stopes now being prepared are in production. The present equipment will be used for loading from stope draw points. The limestone is blended with quarried cement rock to serve as raw material for Portland cement, first produced in this country by Coplay Cement Manufacturing Co. from a process developed by its president, David 0. Saylor, in 1873. For many years the cement rock alone or with a small amount of added limestone was used for raw materials. Later as specifications were raised and the richer portions of quarries were depleted, limestone from outside sources was required in increasing amounts. In 1925 D. J. Uhle, the general manager, began to prospect company property for limestone.

Jan 1, 1954

By S. Fugleberg

As a result of research work done during the planning of the Kokkola zinc plant it was found that a very efficient cementation of impurities from the suspension obtained after leaching copper and cadmium cakes was achieved by adding zinc dust to the batch without filtration after the leaching. All elements nobler than cadmium are precipitated with the exception of lead, which must be removed in a separate step. Using pure zinc dust, free from noble metals, the cadmium sponge produced will only contain elements that can be re- moved from cadmium by meltrefining. The process is thus : 1. Leaching and purification 2. Removal of lead (with BaCO3) 3. Precipitation of cadmium sponge with pure zinc dust 4. Meltrefining of briquetted sponge with NaOH for removal of Zn (and others) The paper deals with the removal of the most critical elements, i.e. Co, Ni, As, Sb, Cu, Pb, T1 in the liquid phase and Zn and T1 in the melt. A survey is also given of the behaviour of most of the other elements normally found in Cd raw material, such as Ge, Te, Se, Sn, In, Ga. It is shown that in most cases the benefit of an electrolysis in Cd production is very limited. In Kokkola 99.998% Cd is achieved by this method, but in favourable cases it may be possible to come quite close to five nines.

Jan 1, 1973

By J. B. Clemmer

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 600,000 lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgC03), usually is associated with lime-stone (CaCO3) and dolomite (MgC03 CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amor-phous) forms.2 The more common crystal-line mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories.

Jan 1, 1940

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of continued interest in the dry beneficiation of gypsum and the development of higher capacity color-sorting machines. These tests should be considered only as an indication of the efficiency of the process and only with respect to the low-grade, untreated ore tested. Although most of the ore mined in Martin County, Ind., is of acceptable quality, a few thin carbonate strata and irregular nodules of dolomite and limestone are present within the main evaporite bed (Fig. 1).

Jan 1, 1969

By V. R. Thompson, R. C. Westgren

In a recent paper,1 the solid-solution strengthening of tungsten and tantalum in a portion of the W-T;-MO-C~ alloy system was described. Additions of tantalum and columbium to tungsten led to significant strengthening, and the introduction of dispersions into these alloys was suggested as a means of further increasing strength. Dispersion strengthening of columbium and molybdenum alloys has been studied extensively.2-4 The approach used to dispersion-strengthen molybdenum alloys appeared equally suitable for tungsten alloys, and, therefore, a brief study was undertaken to determine to what extent the introduction of carbide dispersions would strengthen a solid-solution tungsten-base alloy. A base composition of tungsten and 10 to 12 pet Cb was selected; previous work1 had shown that the tensile strength of this solid-solution alloy was 50,000 psi at 3000°F. For the study of the effects of small additions of

Jan 1, 1964

By W. H. Triplett

THE purpose of this paper is to record a few field observations and accumulated office data concerning outcrops, relation of ore occurrences to intrusive and host rock, and mineral zoning. Reasons for some of the phenomena are not clear to the author so the facts are given with the hope that other investigators may be able to furnish the explanations. The Avalos unit of the Compania Minera de Penoles, S. A., operates the Alicante, Bonanza, Providencia, Albarradon, San Eligio, Nazareno, Leona, Salaverna, and Santiago mines situated between Avalos railroad station and Concepcion del Oro on the Coahuila and Zacatecas railroad in the State of Zacatecas, Mexico. Some of these mines are within Penoles property while others are on mining claims leased from the Compania Nazareno, y Catasillas, S. A., Mazapil Copper Co., and the American Smelting and Refining Co. The main office and camp are at Providencia, about 170 km southwest of Monterrey, N. L., so the silver-lead-zinc mines of the district are usually referred to as the Providencia mines. The Aranzazu, Catarroyo, and Cabrestante copper-gold. mines are situated a few kilometers to the southeast on the same mountain range near Concepcion del Oro, the name by which the camp is known. It is operated by the Mazapil Copper Co. The main theme in the following pages is a description of the silver-lead-zinc ore occurrences of the district. Rock Formations Sedimentary Rocks: Many competent geologists have contributed generously to an ample fund of information concerning the sedimentary columns of northern Mexico. Among them are Carlos Burckhardt, E. Böse, L. B. Kellum, .and R. W. Imlay. Carlos Burckhardt who covered a number of extensive areas in many parts of the Mexican Republic, devoted years to mapping the geology of the Caja, Zuloaga, and Santa Rosa mountain ranges around Mazapil, Concepcion del Oro, and San Pedro de Ocampo, Zacatecas. He did most of the original mapping which has been used as a basis and amplified by others. C. E. Burbridge and, more recently, John

Jan 1, 1952

By R. R. Nash, W. F. Sheely

Experiments were conducted on magnesium monocrystals in order to collect quantitative information on the mechanisms which limit the rate of basal slip. Using critical shear stress and creep data, activation energies for creep at low aid at high temperatures were derived. The activation energy at low temperatures is the same as that for jog formation and the activation energy at high temperatures agrees with that for climb. COTTRELL has suggested that at low temperatures, the expansion of dislocation loops under stresses near the yield strength is limited by the rate at____ which the expanding loops can cut the "forest" of dislocations passing through the glide planes.' On the basis of this mechanism, seeger2 has derived expressions for low-temperature creep and for the relation of flow stress of single crystals to temperature. In the work reported here, the authors have performed experiments designed to obtain quantitative data on the physical properties of the dislocation intersection mechanisms operating during basal slip in pure magnesium monocrystals. Above a critical temperature, dislocations thread-

Jan 1, 1961

By Robert W. Metcalf

THE name "tripoli" is used to designate a number of more or less similar types of silica of sedimentary origin. Usually they are spoken of as "soft" silicas, and are light, very fine grained, porous, and friable. Structure is microcrystalline or cryptocrystalline. The deposits are the residual product of weathering and occur in massive form, either blocky or in friable masses. Tripoli is the end product of the weathering of siliceous Limestones, cherty limestones, or cherts. Weathering removes the calcium carbon- ate, leaving a finely divided siliceous residue to which the name "tripoli" has been applied. Authorities differ as to whether the chert accumulates first and is converted into tripoli or the tripoli is derived by direct decay from various forms of silica during initial weathering of the Limestone. It has also been asserted that tripolis were formed in situ in essentially their present condition as a flocculent, colloidal silica, but it is now believed by most geologists that varying degrees of pressure, combined with one or more methods of origin, have influenced the characteristics of the deposits. Considerable confusion has existed as to what constitutes tripoli. Owing to the similarity of names, tripolite, a type of diatomaceous earth found originally in Tripoli in northern Africa, has been erroneously called tripoli. Tripoli, however, contains no diatoms, the distinguishing characteristic of diatomaceous earth. The material mined in the Missouri-Oklahoma area has been considered by the trade to be the type material, and many feel that the term "tripoli" should more properly be restricted to the product of this region. Although also designated as soft silica, it would be less misleading, perhaps, if the siliceous material mined in southern Illinois were called amorphous silica. Both the Missouri-Oklahoma and Illinois materials are very high in silica. Different in composition, as it is very much lower in silica content than tripoli or amorphous silica, yet included under the classification of tripoli in Bureau of Mines statistical data, is the small but important output of rottenstone in Lycoming County, Pennsylvania. The principal justification for grouping these three types of silica is similarity of use.

Jan 1, 1949