Search Documents

By W. R. Crane

The effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. Drainsge in these mines has been discussed in papers on mining practice,' but the fact that water, varying from 0.16 to 3.46 and averaging 1.43 times the amount of ore mined, has to be pumped from the mines daily, indicates the importance of the problem and the advisability of making a thorough investigation of the source of mine water, its mode of entry into the mines, its effect upon mining conditions, and consideration of means of improving the conditions.

Jan 1, 1927

By Carl A. Holley

Agglomeration is very closely identified with the mining industry. Ores must be crushed finer and finer to separate minerals from gauge and the fine ore concentrates must be agglomerated so they can be handled for further processing. This paper reviews each type of agglomeration device and summarizes the areas of usage for each type of agglomerator.

Jan 1, 1980

By Gerard Matthes

WITHIN the last three years, aerial mapping has made wonderful progress. Its three sources of development in North America may be enumerated as follows: (1) The work of the U. S. Army Air. Service and Corps of Engineers at the McCook Experimental Field, Dayton, Ohio. This is generally regarded as the backbone of this class of endeavor in the United States. (2) In Canada, a great deal has been accomplished in a practical way by methods that have not even been tried out in the United States. Under the leadership of the late Doctor Deville, the Dominion Land Surveyors have turned out reconnaissance maps of large areas at very, small cost. (3) Private capital has contributed a great deal toward development of aerial mapping in a practical way in the United States. Prominent in this regard stands the Fairchild Aerial Surveys, Inc. which has spent large sums in research and development work, especially in the construction of aerial cameras. Its camera is, at present, the official camera of the U. S. Army and Navy Air Services, also, of the Canadian and Brazilian governments. Aerial photographic surveying is a flexible process and adapted to a variety of uses. To date, it has proved. of direct practical value for engineering projects such as reservoir and power transmission surveys, railroad location, drainage, harbor front studies; also, for many commercial purposes, tax assessment, city planning, forest surveys, and lawsuits. In a few instances, aerial photographs have been used successfully by geologists as base maps on which to record field observations, thereby dispensing with pacing and compass surveys. There is reason to believe that, eventually, the aerial map will find wide application in the work of geologists. The reason for advancing this opinion is that aerial maps have, in other fields, proved more complete as regards detail than maps made by standard processes of surveying and drafting, and often are more accurate than the latter. At the present time, five distinct uses are being made of aerial photographs: There is the "oblique" photograph taken at an angle with the horizon; it is used extensively for illustrations in newspapers, magazines, and advertisements. Also, for reconnaissance purposes, it has been found of great practical value. For illustrating reports of engineers and geologists, it offers many obvious advantages. In the Canadian Surveys, maps have been compiled from oblique photographs.

Jan 3, 1925

By C. H. Bowen

Industry needs a generally applicable means of defining average grain sire and grain size distribution. Students of sediments have explored this field, employing methods that might also prove useful in engineering problems. Before attempting to solve specific problems it is well to review the derivation of commonly used grade scales and the reasons for their selection. This aspect of the problem seems largely to have been lost, and a review of basic factors may suggest causes for failures in using size analysis data.

Apr 1, 1956

By Augustus Locke

San Francisco Meeting, October, 1911.) Two Opposed Interpretations of the Tonopah Structure.-The important geological publications concerning the Tonopah mining-district are those of Spurr 1 and of Burgess.2 In these publications are presented fundamental differences of interpretation, which are the more interesting because both authorities have had ample opportunity for observation, and because both are geologists of proved ability. I was vastly puzzled to know which had the better of it, and in order that I might reach a conclusion in my own mind, I recently spent some time in the district going over the physical evidence. Surprising as it may seem, this evidence looks agreeably conclusive. A review of it will, I believe, be of interest to those who are familiar with the previous publications. The general geological features of Tonopah are shown in Fig. 1, and the differences of interpretation referred to are outlined in the accompanying notes. Briefly, Burgess regards the various rocks as flows, lying in the order of their deposition. Spurr regards them in part as flows, and in part as flat-lying intrusives. The disagreement, then, concerns the rocks regarded on the one hand as intrusives, and, on the other hand, as flows. These rocks are chiefly the so-called calcitic andesite, the upper rhyolite, and the lower rhyolite. Economic Importance of the Question of Interpretation.-The economic importance of the question of interpretation is, of course, limited to its bearing on the probable distribution of 1 Geology of the Tonopah Mining District, Nevada, Professional Paper No. 42, U. S. Geological Survey (1905). Report on the Geology of the Property of the Montana-Tonopah Mining Co. (1910). An abstract of this report is given in the Mining and Scientific Press, vol. cii., No. 16,p. 560 (Apr. 22, 1911). 2 The Geology of the Producing Part of the Tonopah Mining District, Economic Geology, vol. iv., No. 8, pp. 681 to 712 (Dec., 1909).

Feb 1, 1912

By Everett Parker

THIS paper describes the methods used to determine the rates of payment for contract work and the plan of contract supervision in the Elm Orlu mine. A discussion of the theory of wages and the eternal question-what is a just wage-are beyond the scope of this article. In the fall of 1920 the Elm Orlu was the largest mine in Butte using the day's pay system of payment for stoping operations. High labor and supply costs and a falling market for the product of the mine made economic mining difficult. The mining method had been changed from the square set stoping to timbered rilling to eliminate most of the shoveling. There was no opportunity to reduce the cost of supplies other than more rigid economy in their use. It was recognized, however, that the labor efficiency was low and that the reduction in costs depended on increasing the output per man. While in general, the low man efficiency was a resultant of the high wages paid and the shortage of men during the war and subsequent period of inflation, it was felt that the contract and bonus system used in the other mines was the main factor in that the most capable and energetic men had been attracted to those mines where more than average skill and dili-gence were recognized by more than average pay.

Jan 1, 1927

By R. G. Clay, C. F. Seaman

THE mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that time, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered, the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. ORIGINAL EQUIPMENT AND INSTALLATION A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots and the up position would connect it to the line from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1942

By Robert E. Thurmond, E. D. Spaulding, Walter E. Heinrichs

DISCOVERY of a commercial ore deposit has resulted from a program emphasizing geophysical techniques and concentrating upon exploration of alluvial-covered areas. United Geophysical Co. selected these areas as offering the best possibility of success, for here the surface evidence of ore deposits has been hidden from the eyes of prospector and geologist alike. Pima mining district, Pima County, Arizona, was selected for initial exploration. The project was successful in that a commercial ore deposit was discovered and proved through drilling and extensive underground development.

Jan 2, 1954

By G. M. Ritcey

Continuous contacting equipment for solvent extraction can be divided into two major areas, according to whether their mode of operation is stagewise or differential (Figure 1). Mixer settlers and the recent Kenics and Sulzer mixers typify the stagewise contactors. In these counter- current contactors, the aqueous and the organic phase are mixed and then separated in a large settling area before the next stage of mixing. Countercurrent differential contact- ors, such as centrifuges and various types of columns, are more compact in that they require less ground area than mixer settlers. [ ] Contactors, in addition to being either stagewise or differential, can be further subdivided into non-agitated and agitated depending on the method used for mixing the phases and producing the countercurrent flow. The simplest contactors such as spray, packed, or perforated plate columns achieve both the mixing and countercurrent flow by means of the gravity difference between the two phases. In agitated contactors such as the Scheibel, Reciprocating Plate, and Sieve-Plate Pulse, mechanical agitation is introduced but gravity differences still produce countercurrent flow. To conserve plant space, and for large throughput with short contact time, centrifugal contactors are used where possible. The reader can refer to reviews on the subject (1-11).

Jan 1, 1978

By J. B. Clark, A. S. Yue

PfANN1 has shown that when a cylinder of molten binary alloy freezes directionally, the solute distribution can be described analytically by cg=k(l-g)k-1 [1] in which Cg is the solute concentration in the solid at the point where a fraction g of the original liquid has frozen and Co is the initial solute concentration. The term k is the effective distribution coefficient of the solute and is defined as the ratio Cx/CL where Cl is the solute concentration in the main body of the liquid. Both the slope and the intercept at -log (1 - g) = 0 of a logarithmic plot of Eq. [I.] provide a measure of k. Under conditions of freezing where diffusion in the solid is negligible and the solute concentration in the liquid is uniform, the effective distribution coefficient k, derived as above, is equal to the equilibrium distribution coefficient taken from the phase diagram. However, under ordinary freezing conditions, even though solid-state diffusion is negligible, the solute rejected from the freezing solid does not have sufficient time to diffuse uniformly throughout the main body of the liquid. A concentration gradient is formed in a boundary layer in front of the advancing solid-liquid interface as pointed out by Rutter and Chalmers.' Thus, under these conditions, the concentration of the freezing liquid in the boundary layer is higher than that predicted from the equilibrium phase diagram and consequently the effective distribution coefficient k, obtained from directional freezing experiments, is larger than the equilibrium distribution coefficient. The symbol k will designate the effective distribution coefficient in the discussion which follows. In this paper, the determination of the effective distribution coefficient is demonstrated for several dilute binary alloys and a polynary magnesium alloy. The effect of freezing rate on the value of the derived k is presented in detail. An example for the calculation of the solidus in a dilute binary solution using the experimentally determined effective distribution coefficient is given. MATERIALS STUDIED Binary magnesium alloys of copper, nickel, and zinc containing approximately 0.10 wt pct solute and a polynary alloy containing approximately 0.10 wt pct each of several elements were selected for study. The spectrographic analyses of these alloys are given in Table I. The analyses are believed accurate to within +5 pct of the stated value. EXPERIMENTAL PROCEDURE Extruded rods of the alloys, 3/8 in. in diam and 11 in. long were used for directional freezing studies. The alloy rods were melted horizontally in a high-purity graphite boat by a Nichrome-wound tube furnace which moved parallel to the length of the rod. The boat was supported inside a Vycor tube suitably connected to provide a protective atmosphere of dry SO2. For an experimental run, the following procedure was used. The alloy rod was cleaned in dilute HNO, and dried. The graphite boat containing the alloy rod was placed within the Vycor tube and the tube connected to the gas train' The 'ystem was purged for 20 min with dry argon and then a flow of dried SO, was maintained for the duration of the run. The movable furnace was positioned and either all or a desired portion of the alloy rod was melted. After attainment of steady-state temperature gradients the molten bar was solidified from one end to the other at a controlled rate by pulling the furnace along the length of the bar at the desired speed. At the conclusion of the run, the directionally frozen alloy rod was analyzed spectrographically at 1 1/4-in. intervals.

Jan 1, 1961

By William E. Bruce

In recent investigation of drilling processes, the U.S. Bureau of Mines measured the operating characteristics of two percussive drills. Basically, this entailed measuring maximum piston velocities while drilling. The maximum piston velocity is not necessarily the same as the striking velocity. The latter is usually somewhat lower1 because most commonly used drills provide an air cushion which slows the piston just before it comes in contact with the drill rod. Penetration rates for the two drills were determined in nine rock types, and the physical properties of the same nine rocks were measured and tabulated. Then the penetration rates were plotted against the individual properties to determine the general relationships on which methods for predicting drilling rates could be based.2

Jan 1, 1970

By B. S. Taylor, J. D. Fraser, W. L. Chen

Steam coal quality is less stringent than metallurgical coal quality. Steam coal is prepared either by cleaning a full-size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to US eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation the Rotating Probability Screen, developed by the British Coal Board, may be used for easy change of raw coal separating size, and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1985

By I. R. Taylor

Vanadium has recently joined the growing list of mineral commodities being exploited by surface mining methods. Union Carbide Corp. controls several vanadium deposits in central Arkansas near the city of Hot Springs in Garland County and the community of Magnet in Hot Spring County (Fig. 1). Two open pit mines, located approximately five miles southeast of the city of Hot Springs in the Wilson Springs area, have been developed for production during the past two years. Adjacent to the mining area the company has recently completed a 1,600-ton-per-day (tpd) processing plant to treat the Wilson Springs and Magnet Cove ores (Fig. 2). Although this operation constitutes the largest vanadium mining project in the United States, the open pit mines are of moderate size. A number of small to medium-sized surface mines will be developed during the life of the operation. This chapter describes the methods and practices used to bring these recently discovered vanadium deposits into production. PRELIMINARY EXPLORATION The vanadium potential of the deposits near Hot Springs and Magnet Cove was first investigated by Union Carbide Corp. in 1960. These areas have long been of interest for their varied mineral content and were previously explored by government agencies and private interests for titanium, columbium, molybdenum, and uranium. No sustained operations resulted from this early work, although the rutile deposits of Magnet Cove were worked intermittently between 1911 and 1944.l Significant vanadium concentrations were reported in a U.S. Bureau of Mines publication describing the investigation of a titanium prospect

Jan 1, 1969

By F. B. Plummer, R. B. Newcome

The practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania oil fields30.‡ It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcitc has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a now district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written concerning experimental work on the actual effect of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores2', have developed a method of investigating the results of acid treatment which has enabled them to test numerous cores and to study in some detail the action of acid on the different types of rocks, particularly fine-grained rocks.

Jan 1, 1936

By F. B. Plummer, R. B. Newcome

The practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania oil fields30.‡ It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcitc has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a now district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written concerning experimental work on the actual effect of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores2', have developed a method of investigating the results of acid treatment which has enabled them to test numerous cores and to study in some detail the action of acid on the different types of rocks, particularly fine-grained rocks.

Jan 1, 1936

By T. D. Yensen

AGING is a term that connotes a slow change in properties under ordinary operating conditions. It can be accelerated by increasing the temperature and by mechanical straining. The magnetic properties of iron and some of its alloys have for many years been known to be subject to such a change. But the cause of the change was not recognized until a few years ago after mechanical age-hardening in non-ferrous alloys of the "duralumin" type had been definitely shown, by means of solid solubility curves, changes in electrical resistance and microanalysis, to be caused by slow precipitation of one or more con-stituents from the solid solution. The similarity between the solid solubility curves of such alloys (Fig. 1) and those for iron-nitrogen (Fig. 2) and iron-carbon alloys (Fig. 3) below the Al transformation point suggested at once that magnetic aging of iron might be caused by a similar process; namely, by the slow precipitation of carbon and nitrogen in the form of Fe4N and Fe3C at ordinary temperatures because of a cooling rate that had been too rapid to permit complete precipitation according to equilibrium conditions. This suggestion has since been amply confirmed, particularly by the comprehensive work of Köster1 on the effect of nitrogen and carbon. Typical curves are shown in Fig. 4 for the relationship between aging temperature and coercive force. Previous to the establishment of the precipitation-hardening theory it was thought that the effect of nonmetallic elements like C, N, 0, etc., on the magnetic properties of iron was greatest when these elements were retained in solid solution, atomically dispersed throughout the interstitial spaces of the iron lattice2.

Jan 1, 1935

Alfred C. Young† (communication to the Secretary): Before the appearance of Mr. Scott's paper in these Transactions we were not specially interested in the investigation which he has started; but at his request we have endeavored to collect from musty records and the recollection of our old friends a brief chronicle of the progress made by this house. As 3000 instruments were manufactured by us before any descriptive record was kept, and 2000 more before the record contained more than a statement whether the instrument was a transit or a level, and sometimes its size, we approach the task with timidity, trusting that the reader will bear the difficulties in mind, particularly as the writer's predecessors, from whom, no doubt, the information desired could have been obtained, have passed away. Instruments for surveying were manufactured by David Rittenhouse, of Philadelphia, as early as 1760; but it was not until late in the first quarter of this century that there was any American market for an instrument outside of the ordinary surveyor's compass. With the advent of canals and railroads, and the more extensive development of the Pennsylvania coalfields, arose a demand for surveying-instruments to meet problems in engineering beyond the limited field of the compass. On May 1, 1820, in which year the practical mining of anthracite coal in Pennsylvania began, William J. Young, who had served his apprenticeship with one Thomas Whitney,

Jan 1, 1901

By Gordon W. Hodgson, Edward Tipman

INT'RODUCTION An appreciable number of the oil fields in Western Canada are accumulations of heavy black oils in more or less unconsolidated sandstones. When the crude oils are produced by conventional means, they are frequently contaminated with both sand and oilfield water. The water is usually present as emulsified water, and the sand and other solid materials are suspended in the emulsions. The presence of the solid material in the crude oils is troublesome and, in general, little is known about the behavior of suspended solid particles in emulsions. The Stokes equation describes the behavior of suspended particles in homogeneous fluids in terms of particle size, density differential, and fluid viscosity. In the case of an emulsion, particle size and density differential introduce no difficulties, but considerable doubt centers around the viscosity term. It has been reported1 that the viscosity of an emulsion is related to the viscosity of the continuous phase by an expression of the type: n = a, (1 + a C) where n is the viscosity of the emulsion, n,, is the viscosity of the continuous phase, a is a constant, C' is the volume concentration of the disperse phase. The value of 17, the coefficient of the concentration term, has been determined for various systems, and has been found to vary from a value of 1 to 4.75. The value of 2.5 has been found to be applicable to a large number of systems, and this is the value that is widely used in the equation which then becomes the Einstein equation for the viscosity of emuls~ons. It is of considerable significance that neither the particle size nor the viscosity of the disperse phase enters the expression; the expression for the viscosity of the enlulsion is based solely upon the viscosity of the continuous phase and the concentration of the disperse phase. For crude oil emulsions the Simha equation and the data presented by Fukushima and lchimurai show a non-linear dependence of the viscosity ratio on the water concentration. While it is undoubtedly reasonable to use these data for predicting the viscosity of a specific emulsion, and while it is equally reasonable to expect the calculated viscosity to predict the settling rate of a solid spherical particle in the emulsion by means of Stokes equation, there seems to be no direct evidence that this calculation is indeed sound for describing the settling rates of solid particles in emulsions of water in crude oils. PROCEDURE A direct approach to the problem was thus indicated. Laboratory equipment was designed and built for the direct determination of the rate-of-fall characteristics of solid particles in emulsions of water in oil. Although the apparatus incorporated the basic design of conventional falling-ball viscometers, the study was concerned directly with the rate-of-fall characteristics of particles in emulsions, rather than with the viscosity of the emulsions as such. The crude oil used in this study was a very heavy black crude oil—the McMurray oil obtained from oil-soaked sands outcropping on the Athabasca River in northeastern Alberta. It was produced from the sands by strip mining followed by hot-water separation of the oil in the separation plant of the Alberta Government at Bitumount'. The primary plant product was a wet crude oil containing about 5 per cent solids and 35 per cent water. The final plant product was only slightly different from the native oil, having lost only about 4 per cent of its bulk as light ends during dehydration distillations. In the present investigation two kerosene dilutions of the McMurray oil were used in addition to the dry plant product. The McMurray oil contained 1.92 per cent solids. Analysis of the solids by X-ray diffraction showed the presence of kaolinite, pyrite, and illite as major constituents. with lesser amounts of quartz. Particle size of the pyrite and quartz was less than 10

Jan 1, 1957

By Spencer Cragoe

I have read with much interest the elaborate and able paper of Messrs. Granger and Treville on the Mining Districts of Colombia, presented at the Atlantic City Meeting (ante, p. 33). Going into detail, however, as the paper does—and particularly with reference to the department of Antioquia, I am somewhat surprised that the property of the Frontino and Bolivia Company, probably one of the richest and most extensive in Colombia, should come off with such scant notice. The entire property embraces an area of some 28 square miles, and is situated at a distance of about 2 leagues from Remedios—after Medellin probably the most important town of the Department—and lying in approximately '7° N. latitude. The neighborhood of Remedios has been long celebrated for its production of the precious metal. Alluvial gold in large quantities has been obtained from the vicinity for upwards of two centuries; and even to-day a large proportion of the population finds a comfortable livelihood, during the dry season, in washing the sands of various rivers, notably the Rio Porce; while the amount of gold, in the form of nuggets, brought almost daily to Remedios and other points, from streams in the immediate neighborhood, is astonishing. These nuggets vary much in size. The majority, of course, are small, but larger ones are by no means scarce. I have been considerably surprised at the amount and value of the trade thus transacted between natives and merchants of the various towns. The property owned by the Frontino and Bolivia Company has been, I believe, for the larger part of the present century,

Jan 1, 1899

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but cannot be obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O'okiep Mining Co. in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1973