Search Documents

By J. H. Frye, J. W. Caum

One of the most important methods of increasing the hardness of metals is alloying. In spite of the widespread use of alloys, the fundamental mechanism of alloy hardening is little understood. This is true even of the simplest form of alloy, the primary substitutional solid solution in which solute atoms substitute for solvent atoms at random in the crystal lattice of the latter. A fundamental understanding of the mechanism of solid-solution hardening would be important, both because of the widespread use of alloys of this type and because of the light that might be thrown on the mechanism of hardening in more complicated alloys. The present investigation covers the hardness of primary substitutional solid solutions of zinc, gallium, germanium, and arsenic in copper. All of these are B subgroup elements from the third period of the periodic table. Cu, Zn, Ga, Ge, and As are in groups I, 11, 111, IV, and V, respectively, and lie just to the right of the transition elements. Because of their cost, it is unlikely that Ga-Cu and Ge-Cu solutions will ever be of commercial importance, but the intent of this study has been to discover some of the fundamentals of solid-sdstion hardening and it has been demonstrated that such a study is far more likely to be fruitful if alloys are made up on the basis of position of the constituent elements in the periodic table than if commercially important alloys are used. Many investigations have been made of the hardness of substitutional solid solutions, but lack of attention to purity of the metals, infrequent grain-size control, and the use of varying testing techniques have virtually invalidated any comparisons. The purpose of most investigations has been to solve immediate problems and not to solve the primary problem: Why do solid solutions usually have a greater hardness than pure metals? Previous Work Theories have been advanced to account for the hardness of solid solutions, but relatively little experimental work has been done. Perhaps the first experimental work of merit was that of Norbury1 on copper alloys. He showed that for several alloys there was a correspondence between the hardness of one atomic per cent solutions and atomic volume of the solutions. More recently Brick, Martin, and Anger2 have investigated the effect of various solute elements on the hardness of copper. They concluded that the hardening effect of these solutes depended "primarily on the difference in atomic volume of solute and solvent or, relatedly, upon the parameter change of the solvent or the extent of solid solubility." They also observed the effect of these elements on hardness and texture developed by rolling and by annealing of rolled material. Austin3 examined the hardness and response to heat-treatment of various iron solid solutions. Frye and Hume-Rothery4 measured the hardness of a number of silver solid solutions containing approximately 1 References are at the end of the paper.

Jan 1, 1943

By J. H. Frye, J. W. Caum

One of the most important methods of increasing the hardness of metals is alloying. In spite of the widespread use of alloys, the fundamental mechanism of alloy hardening is little understood. This is true even of the simplest form of alloy, the primary substitutional solid solution in which solute atoms substitute for solvent atoms at random in the crystal lattice of the latter. A fundamental understanding of the mechanism of solid-solution hardening would be important, both because of the widespread use of alloys of this type and because of the light that might be thrown on the mechanism of hardening in more complicated alloys. The present investigation covers the hardness of primary substitutional solid solutions of zinc, gallium, germanium, and arsenic in copper. All of these are B subgroup elements from the third period of the periodic table. Cu, Zn, Ga, Ge, and As are in groups I, 11, 111, IV, and V, respectively, and lie just to the right of the transition elements. Because of their cost, it is unlikely that Ga-Cu and Ge-Cu solutions will ever be of commercial importance, but the intent of this study has been to discover some of the fundamentals of solid-sdstion hardening and it has been demonstrated that such a study is far more likely to be fruitful if alloys are made up on the basis of position of the constituent elements in the periodic table than if commercially important alloys are used. Many investigations have been made of the hardness of substitutional solid solutions, but lack of attention to purity of the metals, infrequent grain-size control, and the use of varying testing techniques have virtually invalidated any comparisons. The purpose of most investigations has been to solve immediate problems and not to solve the primary problem: Why do solid solutions usually have a greater hardness than pure metals? Previous Work Theories have been advanced to account for the hardness of solid solutions, but relatively little experimental work has been done. Perhaps the first experimental work of merit was that of Norbury1 on copper alloys. He showed that for several alloys there was a correspondence between the hardness of one atomic per cent solutions and atomic volume of the solutions. More recently Brick, Martin, and Anger2 have investigated the effect of various solute elements on the hardness of copper. They concluded that the hardening effect of these solutes depended "primarily on the difference in atomic volume of solute and solvent or, relatedly, upon the parameter change of the solvent or the extent of solid solubility." They also observed the effect of these elements on hardness and texture developed by rolling and by annealing of rolled material. Austin3 examined the hardness and response to heat-treatment of various iron solid solutions. Frye and Hume-Rothery4 measured the hardness of a number of silver solid solutions containing approximately 1 References are at the end of the paper.

Jan 1, 1943

By Enid C. Plante, K. L. Sutherland

Practical metallurgists are unanimous in stating that oxidation of mined sulphide ore adversely affects separation of the constituent minerals under standard conditions in a mill. Frequently, the need for different operating conditions in different plants is attributed either to the extent of oxidation of the mineral surfaces or to soluble oxidation products. The investigations reported in this paper study the effect of oxidation on the primary condition necessary for flotation, namely that of adhesion of an air bubble to the mineral. Oxidation Products from Sulphide Minerals Weinig and Carpenter1 state that the relative rates of oxidation of some sulphides are: FeAsS > FeS2 > CuFeS2 > ZnS > pbS > Cu2S tetrahedrite. They also show that oxidation is rapid at first, that sulphides of older geological formations are more stable than those of recent date and that mixtures oxidize more rapidly than any one mineral alone. The more rapid oxidation of mixtures is borne out by results of Gottschalk and Buehler2 who found that PbS, zns and cus oxidized 8 to 20 times faster when pyrite was present. Only the end products of oxidation, sulphate and the metal ion, were identified in these tests. Gaudin3 states that pyrite is difficult to oxidize in the laboratory. Winchell,4 using pyrite containing 99.98 pct FeS2, allowed water to percolate through a bed of this ground material. At the end of three months only a trace of Fe+++and So4- were found. Even after 10 months the quantity of Fe+++ was only 7.8 mg and SO4- 25.5 mg per liter of percolating solution. Car-michael5 confirmed Winchell's results on the slow oxidation of pyrite. Usually the oxidation of sulphide surfaces has been conducted in neutral or acid solutions, the acidity being caused by the oxidation products. Eliseev and Nagir-nyaka found that treatment of pure pyrite with lime gave only thiosulphate, but considered it possible that thiosulphate was obtained not by oxidation of the pyrite itself, but by oxidation of calcium disul-hide. Mitrofanov7 suggested that thiO~ulphate was formed by the following process: oxidation of sulphide to give free sulphur (this frequently happens with marcasite), followed by oxidation of the sulphur to sulphur dioxide and reaction of the sulphur dioxide with sulphur to give thiosulphate. Ferric and ferrous hydroxides, or similar compounds, were shown to be present. The Research Staff of the United Verde Copper Co.8 treated ore from the United verde mine with lime. Thiosulphate, sulphide and polysulphides were stated to be

Jan 1, 1949

By A. Eilers

ALTHOUGH the process to which I refer in this paper has been in successful operation for nearly five years, during which time it has been introduced, superseding all other processes having in view the same end, in almost every lead refinery in the country, no description of it, giving economical data, has ever appeared in print, nor has the process been known in its details to any considerable number of engineers beside those conducting it at their works. A discussion of this subject at the present time becomes especially interesting in view of a late publication in the Prussian ministerial organ for Mining and Metallurgy, by Dr. Wedding, in which the method of treating the zinc-silver-lead alloy by distillation, as finally settled upon at Tarnowitz, is very minutely and fully described. It is the more interesting, because in that article reference is made to the American method in an unfavorable light, while, at the same time, it is clear from the article itself, that the most important details of the process, besides the one that it is conducted in black-lead retorts, were not at all understood. In publishing herewith the details of our American method, one of my objects is to invite comparisons between our simple and direct process and the elaborate one at Tarnowitz. In extracting the silver from work-lead by means of zinc, it is always the intention, in this country, to obtain a zinc-crust so rich in silver that the rich lead resulting from subsequent distillation

Jan 1, 1875

By E. H. Jr. Dix

A LACK of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys .and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investiga-tion an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100° C. are too small to be of practical importance.

Jan 1, 1935

By Keith G. Wallace

Small scale open pit mining of the Lucky Mc property in the Gas Hills district of central Wyoming was started in the spring of 1954 and the first uranium ore went to Vitro's mill in Salt Lake City that July. Shortly after mining started it became apparent that accurate ore control for mining purposes would be an absolute requirement. A systematic drilling program was initiated in the spring of 1955, and has been continued up to the present time. Two main mining areas have been developed. Mine 1, at the site of the original ore discovery in the Gas Hills, covers a mineralized zone roughly 600 x 2800 ft. This orebody was outlined and developed by drill holes on 50-ft centers. Approximately 1300 holes were drilled in the area before preliminary mining plans were made and mineable reserves calculated. Reserve estimates were based almost entirely on chemical assays of drill hole samples.

Jan 10, 1958

By Richard L. Ash, Thomas E. Pearse

Most theories of blasting phenomena are based on the condition that explosive charges have a spherical shape. If a cylindrical charge is considered, the explosive is usually assumed to have an infinite velocity of detonation. Another limitation is also often imposed whereby only one free face is considered to exist. Unfortunately, these conditions all serve to limit the number of variables involved and tend to over-simplify analyses. The result is that explanations for actual effects from blasts are seldom realistic. In addition, no solution has yet been found to explain the actions of certain blasting agents that appear to stress materials in a different manner than do many of the high explosives. In order to determine causes for some of the unexplained phenomena, investigations were conducted by the writers on both actual field blasts and theoretical problems. Although many solutions have been proposed to explain the rock breakage processes, none relate the effects of hole depth, explosive and rock energy- propagation velocities with charge placement geometry. Evidence indicates there is a definite interdependence of those factors and that they are of vital importance in proper drill-pattern design. For simplicity most of the discussion in this paper applies to vertical blast-holes drilled in uniform massive rock for open pit blasting, although the basic principles presented apply to all forms of blasting with certain basic modifications being necessary for specific field conditions.

Jan 9, 1962

By P. Bolsaitis, L. Skolnick

Vapor pressures of silver over ternary alloys of six different copper to gold ratios have been measured by means of the Knudsen effusion technique. The data obtained in the temperature range of 1330° to 1375° have been used to estimate the integral excess free energies of the ternary alloys and the activities of copper and gold. The results compare favorably to the predictions based on the electron cell model of alloys recently formulated by the authors. THE orifice effusion method for measuring vapor pressures of materials in condensed phases was first introduced by knudsen, and has since been used extensively for the determination of thermodynamic properties of condensed phases. The basis of the measurement is the effusion, through a small orifice, of vapor in equilibrium with a condensed phase. Assuming free molecular flow into high vacuum, the vapor pressure, P (in mm Hg), of the effusing species is calculated from the following equation:' where w (g) is the weight of effusing species lost during a run, t (sec) the time length of the run, A, (sq cm) the area of the effusion orifice, T ("K) the temperature at which the run is conducted, M the molecular weight of the effusing species, and k the Clausing factor, a constant that corrects for deviations from free molecular flow caused by the finite thickness of the orifice walls.17 The determination of partial and integral thermodynamic variables from vapor pressure data of ternary alloys is possible only if the vapor pressures of all but one component are negligible or can be esti-

Jan 1, 1969

By Perry Harrison

THE mixing of fine ores with fuel and burning under induced draft is called sintering in iron-ore practice and either sintering or roasting in copper and lead metallurgy. The first development of sintering was the Huntington-Heberlein process, in which fine sulfide ores mixed with fuel were charged into a pot and burned under the action of an upcast current of air introduced at the bottom of the pot. Modern development has resulted in two types of machine; the continuous Dwight-Lloyd machine, which consists of heat-resisting grates and a moving beltlike type of hearth constructed of metal, in which air is drawn downward through the bed, and the stationary Greenawalt batch process, which operates in the same manner as the Dwight-Lloyd except that the hearth is stationary. The recent rapid increase in the use of sintering has been the result of two great advances in metallurgical process-flotation and the treatment of flue dust. The Dwight-Lloyd machine is used in many plants for agglomerating flotation concentrates and at the same time reducing the sulfur content to furnace requirements and it has become standard practice to treat iron blast-furnace flue dust by either the Greenawalt or Dwight-Lloyd machine, so that it can be recharged into the furnace. The mining of low-grade magnetite iron deposits and their beneficiating by grinding and magnetic separation resulted in a fine concentrate extremely detrimental to blast-furnace practice. These concentrates are sintered and made into ideal material for blast-furnace use. Incidentally, coke savings of about 400 lb. per ton of pig are reported.

Jan 1, 1930

By R. I. Parsons, M. B. Standing, E. N. Lindblad

The recovery of the heavier components from a gas cap or retrograde pool is shown to be the greatest when the sand is cycled with a dry gas at a low pressure. This conclusion is in direct opposition to the belief that the most efficient production program is pressure maintenance and cycling at or near the dew point. The results are calculated from: (I) constant volume, variable composition pressure-volume-temperature tests on a mixture of trap gas and liquid from a producing well; (2) published equilibrium constant data and the measured composition of the dew-point material; and (3) the fact that in a sand section of homogeneous permeability, injected gas displaces reservoir gas nearly, quantitatively. The results are based on the simplifying assumption that variable permeability systems may be defined by the ratio of two statistical parameters, and that gas injected into an actual sand will behave as though the sand were composed of many layers, each of constant permeability. Introduction Pressure decline in gas-condensate type reservoirs is accompanied by the formation of a liquid phase throughout the reservoir. Over the past ten years the processing of the material from these types of reservoirs for the heavier hydrocarbon components and the return of the light fractions to the reservoir ("cycling") has become increasingly popular. It has often been stated that the purpose of such a program is to prevent the loss of the retrograde liquid phase formed in the reservoir. The purpose of this paper is to present the results of laboratory tests and computations concerned with several possible methods of producing a gas cap or condensate type of reservoir. The results show that the recovery of heavier hydrocarbons for this type of reservoir is not a maximum under conditions of cycling at or near the dew-point pressure. Instead, variations in permeability and the ability of the dry injected gas to revaporize condensate, point to cycling at a considerably reduced pressure as the optimum production-method. In addition the paper suggests a way of evaluating sands for their permeability variation. The calculations presented in the following sections of the paper are in terms of the production of the butanes and heavier fraction from the gas cap of a field which had an original pressure of approximately 3000 psi. Specifically, the calculations show: 1. To what extent the condensate formed in the reservoir after pressure decline can be recovered by the cycling of a dry absorber-plant gas through the sands. 2. Whether there would be greater recovery of hydrocarbons if cycling were instigated at the original reservoir pressure.

Jan 1, 1948

By M. B. Standing, R. I. Parsons, E. N. Lindblad

The recovery of the heavier components from a gas cap or retrograde pool is shown to be the greatest when the sand is cycled with a dry gas at a low pressure. This conclusion is in direct opposition to the belief that the most efficient production program is pressure maintenance and cycling at or near the dew point. The results are calculated from: (I) constant volume, variable composition pressure-volume-temperature tests on a mixture of trap gas and liquid from a producing well; (2) published equilibrium constant data and the measured composition of the dew-point material; and (3) the fact that in a sand section of homogeneous permeability, injected gas displaces reservoir gas nearly, quantitatively. The results are based on the simplifying assumption that variable permeability systems may be defined by the ratio of two statistical parameters, and that gas injected into an actual sand will behave as though the sand were composed of many layers, each of constant permeability. Introduction Pressure decline in gas-condensate type reservoirs is accompanied by the formation of a liquid phase throughout the reservoir. Over the past ten years the processing of the material from these types of reservoirs for the heavier hydrocarbon components and the return of the light fractions to the reservoir ("cycling") has become increasingly popular. It has often been stated that the purpose of such a program is to prevent the loss of the retrograde liquid phase formed in the reservoir. The purpose of this paper is to present the results of laboratory tests and computations concerned with several possible methods of producing a gas cap or condensate type of reservoir. The results show that the recovery of heavier hydrocarbons for this type of reservoir is not a maximum under conditions of cycling at or near the dew-point pressure. Instead, variations in permeability and the ability of the dry injected gas to revaporize condensate, point to cycling at a considerably reduced pressure as the optimum production-method. In addition the paper suggests a way of evaluating sands for their permeability variation. The calculations presented in the following sections of the paper are in terms of the production of the butanes and heavier fraction from the gas cap of a field which had an original pressure of approximately 3000 psi. Specifically, the calculations show: 1. To what extent the condensate formed in the reservoir after pressure decline can be recovered by the cycling of a dry absorber-plant gas through the sands. 2. Whether there would be greater recovery of hydrocarbons if cycling were instigated at the original reservoir pressure.

Jan 1, 1948

By Harry M. Mikami, Harold A. Heiligman

The term chromite is often used to cover all chrome ores and concentrates which are the designations actually employed by most industrial users and producers. Chromite is, of course, the predominant mineral in chrome ores which are aggregates of chromite and gangue minerals, most commonly magnesian silicates. Most chrome ores now used are petrographically chromitites which is a rock, rather than an individual mineral term. The title of this chapter, following past usage, is meant in the broad sense. Chromite is the only primary commercial source of chromium. This book is intended to deal only with nonmetallic minerals and rocks. Chromite uses are both metallic (ferroalloys) and nonmetallic (refractories and chemicals), but any discussion of mineralogy, geology, and mining is common for all types. A number of the major commercial ores are interchangeable, and their uses are determined by economic considerations. Mineralogy COMPOSITION [Chromite is a term embracing a wide range of chromium-bearing spinel*-group minerals the compositions of which can be expressed as (Mg,Fe2+)0.(Cr,AI,Fe3+ )203.t This can be further generalized to R2+O.R23+03 and the molecular RO: R,03 ratio is generally close to one. The exact composition may be arbitrarily expressed as a solid solution of six end-members, MgAI2O4, MgCr2O4, MgFe2O4 FeCr2O4, FeA12O4, and Fe2+.Fe23+04 with the proportions of each stated or plotted in the six-cornered prism of Johnston and Stevens61 or this scheme may be simplified to comprise only three endmembers making up a composition triangle, Fig 1. [ ] FIG 1-Triaxial composition diagram showing molecular compositions of chromites listed in Table 1. The RO.Fe2O3 corner includes Ti02 norms listed in the table. Note that the high-alumina chromites (1, 2, 3, 9), form a cluster well apart from the high-Cr2O3 chromites. There is a tendency for high-iron chromites to be higher in Fe2O3 + TiO2 but it is not a consistent or systematic relationship. The MgO/RO ratio must also be known to characterize the chromite chemically. Simplest and most convenient method is Thayer's' in which a chromite such as (Mg.65Fe.352+)O.(Cr.40Al.50Fe.103+)203 would be written as (Mge,) Cr eAlo. The molecular pro- portions of ferrous and ferric oxides can be seen at a glance as the divalent and trivalent oxides]

Jan 1, 1960

By Walter G. Perkins

In the assay of copper-bearing material for gold and silver, the elimination of copper before the final cupellation is of course essential, because any copper left in the lead-button will carry gold into the cupel; and a method which will effectively remove the copper with the smallest amount of manipullation is desirable. The scorification method is often rendered long and tedious by the necessity of repeatedly re-scorifying the button— to say nothing of the risk of losing Au—Ag thereby incurred. An ore carrying, for instance, 10 per cent,. of copper and only 0.1 or 0.2 oz. gold per ton, cannot be scorified with accurate results, because so many portions would have to be taken in order to get enough gold for weighing. On the other hand, the crucible method, with potassic nitrate and nails, would not do at all in such a case, because all the copper would be reduced by the nails, and (if the charge were 0.5 A. T.) this would defeat cupellation, by causing cupel-absorption of gold. In matte-assays, more concentrated value permits the determination of gold from smaller portions, and thus diminishes the difficulty experienced with ores. The method here described has been severely tested, during use for more than a year, and hart never failed hitherto, in the assay of any ore or product to which it has been applied. It is not proposed as perfect for every variety of ore or matte—probably no method would be that; but it is believed that, intelligently used, with the modifications dictated by practice, it will give better results, with less expenditure of time and labor, than any other known to the writer.

Jan 1, 1902

By G. H. Lair, B. J. Langford, S. H. Rockwood

Volumetric reservoir analysis is dependent upon a firm relationship between porosity, connate water, and net pay. Capillary presswe data on core samples interrelate these three factors. It is shown that other reservoir problems may be resolved: (I) whether water production is indigenous or extraneous to the oil producing interval, (2) an oil-water contact is being approached, and (3) whether the oil-water contact is remotely situated. INTRODUCTION Volumetric analysis of carbonate reservoirs challenges the ingenuity of the reservoir engineer due to an absence of data on the minimum oil-bearing and oil-producing pores of a given reservoir rock. Many studies with this as the ultimate objective are available on the physical characteristics and fluid-flow behaviors of the carbonate reservoir. Some of these publications are: Hassler, Brunner and Deahl's1 study of the role of capillarity in oil production; Jan Law's' and A. C. Bulnes3 statistical treatment of core analysis data; Chalkley's method4,5 or estimating specific surface areas and porosity; Walter Rose's9 report on porosity, reserves, and recovery; Archie's78 tex-tural classification of carbonate rocks; Stewart and Spurlock's9 large core analysis; Purcell'sl0 mercury injection method in studying capillary pressure phenomena; Stewart, Craig, and Morse's" model multiple-phase flow test in investigating the relative permeability effect; and Fatt's12 illumi-nating network model of porous me-dia. The present study shows that the static reservoir parameters of porosity, connate water, and net productive thickness may be interrelated by utilizing a statistical arrangement of mercury capillary pressure data in addition to routine core analysis. This report summarizes the techniques that are followed to obtain these relations which are applicable to carbonate and sandstone reservoirs that do not contain clays. Capillary pressure statistical studies may be extended to include clay-bearing rocks by utilizing water capillary pressure data. POROSITY It is necessary that the laboratory determine the porosity value that includes the pores that are filled with hydrocarbons and water in the reservoir. This is the reservoir's total porosity. When true total porosity values are not available, correlations between porosity and capillary pressure characteristics lose their significance since they cannot be related through oil-base mud core data to the porosity and connate water values found in reservoirs. Methods used to obtain reliable porosity data will not be discussed; however, care should be exercised in selecting samples for measurement. In homogeneously porous formations, small core plugs sampled frequently will furnish adequate information. Where heterogeneity, particularly vugginess, is present, large-core porosity data may be required; in such reservoirs a suite of capillary pressure samples may be selected from small plugs. CAPILLARY PRESSURE Capillary pressure data provide a method for relating two carbonate reservoir parameters, porosity and connate water saturation, which in turn permit delineation of productive rock types necessary for selecting the third parameter, productive thickness. Specific applications of capillary pressure data to petroleum reservoirs were suggested by Archie8 and Pur-cell."' Their work demonstrated that in preferentially water-wet rock, porc

Jan 1, 1958

By F. F. Peng, A. D. Walters, M. R. Geer, J. W. Leonard

INTRODUCTION Washability characteristics derived from float-and-sink analysis in Chapter 4 demonstrate that coal is intrinsically heterogeneous, and this heterogeneity is also evident in the proximate, ultimate, and size analyses. A range of particles from high to low specific gravity is usually seen in the run-of-mine coal. One objective of coal preparation is to recover the high quality float material (the particles of lower specific gravity) such that the recovered product meets certain quality specifications, as well as to reject or recycle low quality particles of higher specific gravity. The maximum recovery of cleaned coal at the required quality is of major concern to plant operators. However, the quantity and quality of products of coal cleaning, determined in the operation of actual commercial cleaning plants and by theoretical calculation based on run-of-mine washability studies, are known to be different with each coal. Therefore, during the last half century, coal preparation engineers have repeatedly sought methods to predict the technical and economical efficiency of separation of cleaning equipment and systems. Many formulas have been proposed by international investigators to evaluate the efficiency of various coal cleaning operations, primarily based on the yield and/or ash of the various products of coal cleaning. Performance criteria in use today are capable of defining all of the important aspects of a given concentrating operation; however each criterion has certain restrictions or limitations. It is important, therefore, to understand how such formulas can be used and the problems involved in their construction. Technical Measure of Plant Performance Conventional means for evaluating a preparation plant's performance are generally approached through the use of equipment performance mea-

Jan 1, 1979

By J. D. Miller, M. Misra

The processing strategy for the effective separation of bitumen from low grade (<l0 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However, the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1981

By George Enos

As the coating formed affects the corrosion rate, duplicate samples of eight non-ferrous alloys were placed in flowing mine water. The alloys tested were as-cast or as-rolled and machined or polished. The paper describes the tests and gives the corrosion losses and the appearance of the samples at the end of the test. AN IMPORTANT factor affecting the rate and nature of corrosion of metals and alloys is the film, or coating, formed on the surface; and this may accelerate or retard corrosive action once started. The formation of films and coatings is intimately associated with the chemical composition and physical constitution of both the metal and the corroding medium. A film or coating may be either the corrosion product resulting from oxidation; that is, an oxide or salt, or a deposition of suspended matter from the corroding media upon the surface of the metal, or a mixture of both. The coating may adhere tightly or loosely to the surface of the corroded metal. In short, a film or coating is the reaction product of the corroding medium and the metal, which adheres to the surface of the metal and with which may be intermingled material from the attacking media not concerned in the chemical reactions. As the, terms film and coating are used by different writers for very different things, distinction is made between the two, by the present writers, on the basis of thickness. Thus, a film is defined as a corrosion product or deposition, on the surface of a corroded metal, that is of such thickness that it cannot be measured by the metallurgical microscope. A coating, on the other hand, is of such thickness that it can be measured. If the resolving power of the 2 mm. (equivalent focal length) apochromatic oil immersion objective (N.A. 1.4) is taken as the limit of the microscope, the limiting resolution is two lines that are 0.0002-0.0004 mm. apart. It is thus possible to measure coatings that are greater than 0.0002-0.0004 mm. thick. This thickness is equivalent to 200,000-

Jan 7, 1924

By L. Douglass Anderson

Fox some years past the annual reviews of the metallurgy of lead have almost uniformly stated that there have been no great changes, such as there were, being more particularly noticeable in the refinement of details. While this is quite true, nevertheless these changes in details are gradually bringing about a condition that, taken as a whole, constitutes a considerable advance in the art. Local circumstances have often -compelled metallurgists to adopt certain peculiarities of practice which -upon trial have been found advantageously applicable to more than the restricted district f origin. This paper will deal &apos; with some of the more novel features developed in recent years at the United States smelter, Midvale, Utah, particularly with reference to the influence of the bag house. The plant is equipped with six blast furnaces, 48 by 160 in., mechanically fed; four Wedge furnaces for roasting matte and sulphide ores; four Dwight-Lloyd sintering machines; 20 converter boxes for blast roasting; storage bins for ore, fuel, and fluxes; "oxide" and "sulphide" sampling mills; bag house taking all the gases of the plant; arsenic plant for treating the dust gathered there; laboratory, shops, etc. The most marked feature of the plant is its complete bag-house system. Of the many schemes thus far tried for preventing damage to surrounding agricultural interests the writer is aware of none as yet quite as efficient as the bag house. A common remark of visitors upon approaching the plant and viewing the clear stacks is that it appears to be shut down, whereas once inside all the evidences of industry are found.

Jan 7, 1914

By L. Douglass Anderson

Fox some years past the annual reviews of the metallurgy of lead have almost uniformly stated that there have been no great changes, such as there were, being more particularly noticeable in the refinement of details. While this is quite true, nevertheless these changes in details are gradually bringing about a condition that, taken as a whole, constitutes a considerable advance in the art. Local circumstances have often -compelled metallurgists to adopt certain peculiarities of practice which -upon trial have been found advantageously applicable to more than the restricted district of origin. This paper will deal with some of the more novel features developed in recent years at the United States smelter, Midvale, Utah, particularly with reference to the influence of the bag house. The plant is equipped with six blast furnaces, 48 by 160 in., mechanically fed; four Wedge furnaces for roasting matte and sulphide ores; four Dwight-Lloyd sintering machines; 20 converter boxes for blast roasting; storage bins for ore, fuel, and fluxes; "oxide" and "sulphide" sampling mills; bag house taking all the gases of the plant; arsenic plant for treating the dust gathered there; laboratory, shops, etc. The most marked feature of the plant is its complete bag-house system. Of the many schemes thus far tried for preventing damage to surrounding agricultural interests the writer is aware of none as yet quite as efficient as the bag house. A common remark of visitors upon approaching the plant and viewing the clear stacks is that it appears to be shut down, whereas once inside all the evidences of industry are found.

Jan 7, 1914

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935