Search Documents

By V. Patarini, D. Kuehl, F. Galasso, M. Salkind

In recent years, a great deal of research has been directed toward the production of continuous low-density, high-strength, high-modulus boron fibers for aerospace applications. A technique which has proven to be quite successful for forming these fibers involves the reaction of boron trichloride and hydrogen on a hot tungsten wire. In this process, a boron fiber is produced which consists of a tungsten boride core covered with amorphous or crystalline boron depending on the temperature of the preparation.2,3 The purpose of this paper is to present the properties which have been obtained to date from measurements and observations on these fibers. Selected samples of boron filament produced by reacting boron trichloride and hydrogen on a 0.5 by 10-3 in. diam tungsten wire substrate using different reacting temperatures were cross-sectioned, polished, and photomicrographed with cross-polarized light. The temperature of the wire was measured using a two-color optical pyrometer. Photomicrographs of these samples are shown in Fig. 1. Three general types of boron, in addition to the tungsten borides, have been identified by means of X-ray powder diffraction techniques: a) at low temperatures (below 1400°C) the boron is deposited in the amorphous form; b) at temperatures between 1400° and 1500°C the boron is deposited in the ß tetragonal form; and, c) above 1500°C the boron is deposited in the B rhom-bohedral form. In the depositing range of 1400" to 1500°C the boron initially deposits as amorphous and becomes crystalline as evidenced by the large equi-axed grains which then merge into columnar grains in later stages of boron deposition. This can be seen in Fig. 1 and has been observed in the X-ray patterns of these fibers, which contain both halos from the amorphous boron and lines from the ß tetragonal form. Above 1500°C the only boron reflections observed in the X-ray patterns were those of the ß rhombohedral form and only columnar grains are seen in the photomicrographs. Photomicrographs of the surface in Fig. 2 show the smooth-surface kernal-type deposition which corresponds to the amorphous form and the rougher surfaces which correspond to the crystalline form. Mechanical measurements were made on amorphous boron produced at 1300°C rather than the crystalline boron because the strengths of these filaments were greater and were more consistent. A tensile tester consisting of a fixed crosshead containing a double

Jan 1, 1967

By K. V. Hoover, D. M. Lapham

In Pennsylvania, 310 sampled sites of clay and shale have been studied with regard to potential use, lithology, physical properties, fired properties, major-element chemical analyses, and quantitative five-component X-ray mineralogy. Approximately 80% of the samples are of some potential use. Binary correlations of test data vs. potential use indicate that certain empirically determined parameters may be critical. These are: lithology, particularly for medium to superduty refractories and lightweight aggregate; kaolinite content for refractories vs. low-temperature fired product sources; quartz analyses with an apparent necessary minimum quantity for brick; quartz content, which is low in high grades of lightweight aggregate; mica content, which is low for refractories and possibly high for lightweight aggregate; total iron, which is low for refractories and shows a 4.0% minimum for lightweight aggregate; carbon dioxide, which is low for refractories, beneficial in lightweight aggregate, and probably restrictive for some tiles; chlorite-vermicalite, which is low for refractories and possibly beneficial in lightweight aggregate. In Pennsylvania, clay and shale materials constitute one of the state's major economic mineral resources. To date, the testing program indicates considerable development potential in brick, tile, and lightweight aggregate industries and perhaps a future potential for aluminum from shales that exceed 20% AID..

Jan 1, 1972

By H. R. Hose

Total crude fluorspar reserves in western Europe, containing more than 35 pct CaF*, are estimated at 12 million metric tons, while reserves in the USSR and Soviet sphere may exceed 5 million metric tons. The bulk of these reserves are concentrated in the USSR, Spain, United Kingdom, Western Germany, and Italy. Since published estimates of the tonnages of individual mines and explored deposits are not available for most countries in Europe, the estimates given in Table I for individual countries are necessarily approximate, as they have been compiled from various sources and modified and combined according to the author's judgment. The majority of fluorspar deposits in Europe belong to the late Paleozoic metallogenetic epochs and have been found within or along the borders of the Hercynian massifs. Deposits in the Central and Esterel massifs of France, those of Western and Eastern Germany, Sardinia, the Catalonian coastal range and the Sierra de 10s Santos in Spain, and those of Devonshire and Cornwall belong to the Hercynian metallogenetic epochs. The deposits in southern Norway and Sweden belong to the middle Paleozoic or later, those of northern England to the late Paleozoic or later, those of northern Spain and Greece to the late Mesozoic, and those of northern and probably central Italy and Switzerland to the early Tertiary. Fluorspar occurs typically in veins, lenses, and stringers, but also in bedded replacement deposits and pockets, and may be colorless to white, yellow, green, pink, brown, blue, or purple to almost black. Except for the colorless variety, the only kind which can be used for the optical industry, the color of the fluorspar does not affect its ultimate use,

Jan 4, 1955

By William E. Bruce

This paper is intended to provide an improved understanding of natural draft (natural ventilating pressure) and the effect of natural draft on underground mine ventilation circuits. Attention is focused on measurement of natural draft pressures during ventilation surveys in mechanically ventilated mines and on different methods for modeling natural draft using the measured data. A number of examples are presented which utilize data collected during absolute air pressure surveys made by personnel of the Ventilation Division of the Mine Safety and Health Administration's Safety and Health Technology Center, Denver, Colorado. Examples are used to illustrate how the data from absolute air pressure surveys may be interpreted to determine whether natural draft pressure is present and what its magnitude is. In addition, two different methods are described for mathematically estimating the magnitude of the natural draft pressure. Comparisons are made of results obtained using the different methods. Different procedures are described for modeling natural draft using the MSHA-modified Penn State computer program. Use of the routines is described and illustrated relative to drafts that aid or oppose the mechanical ventilation system. Tabulations of results facilitate comparison of outcomes obtained using the different modeling procedures.

Jan 1, 1982

By D. P. Morton

SINCE 1023, which closed the speculative era in the bituminous coal fields of the United States, there have been wide annual fluctuations in the national production of bituminous coal. These changes in annual output have been variously attributed to: (I) increased competition from petroleum products, natural gas and hydroelectric power; (2) lower unit consumption of coal; and (3) fluctuations in the general business level. The purpose of this paper is to measure, from a practical standpoint, the net effect upon the annual trend of bituminous coal production, and to give those who are interested a basis for estimating in advance the probable output of bituminous coal. It can readily be shown that changes in the level of general business affect the national production of bituminous coal more than does any other factor. Therefore it is necessary to use some standard measure of the relative business level for purposes of comparison. The Federal Reserve Board Index of Industrial Production offers the basis for such a measure.' This Index, a weighted composite of 81 different series, rests upon the averages of the years 1935 to 1939 as loo, and is presented graphically in Fig. I. Even a cursory examination of the chart will indicate a definite uptrend for industrial production over a period of years. This uptrend is due to at least two factors: (I) an actual increase in national population, and (2) a probable increase in the per capita consumption of goods. This means that there is no such thing as a fixed Normal, rather Normal is a variable, tending to increase from year to year. In order to measure the amount of annual increase in normal, the Index of Industrial Production must be studied in relation to its major components, Durable Goods and Nondurable Goods. Durable Goods are those made from the lasting materials such as iron, steel, other metals, lumber, stone, cement, clay, glass. Nondurable Goods are those for early consumption, such as foods, textiles, tobacco, chemicals, paper, gasoline, and goods made of leather and rubber. The purchase of Durable Goods may be postponed, but Nondurable Goods must be purchased currently unless the standard of living is lowered. The Federal Reserve Indexes of durable and nondurable goods are shown graphically, 1920 to 1939, on Fig. 2 (pp. 764-765 of ref. I). It is apparent that fluctuations in the production of nondurable goods are not nearly so wide as in the production of durable goods, and that the curve of Industrial Production (Fig. I) would fall between the two curves on Fig. 2. It would, however, seem logical that both curves should follow the same long-term trend, or that over a period of two to three decades the relative proportion of durable and nondurable goods, in periods of normal production, should he the same. It is neces-

Jan 1, 1941

By R. C. Wilmoth, R. D. Hill, R. B. Scott

A cost breakdown is given for reclamation and mine drainage abatement conducted by the Federal Water Quality Administration's demonstration project near Elkins, W. Va. Costs for construction of control measures have been developed and include backfilling strip mines, sealing subsidence areas, reconstructing stream channels, and installing mine seals to prevent the entrance of water and air.

Jan 1, 1973

By J. E. Lamar, J. S. Machin

INSULATING materials include a wide variety of nonmetallic mineral products such as exfoliated vermiculite, expanded gypsum, 85 pct magnesia, diatomite, asbestos, perlite, cellular glass, pumice, silica aerogel, expanded aggregates and mineral wool. Except mineral wool, most of these products, or the materials from which they are manufactured, are described in other chapters of this book. PROPERTIES OF INSULATING MATERIALS The insulating properties of the materials considered in this chapter result in general from entrapping extremely small pockets of air in such a manner that heat is not transferred by convection. The minimum heat conductivities of such insulating materials are slightly greater therefore than the conductivity of still air. In addition, conductivity varies with the overall density of the material, the temperature range in which the measurements are made, and the form into which the material is fabricated. However, the numerical value of heat conductivity should not be the sole criterion of an insulating material; for a particular application it may be advantageous to use a material of somewhat higher conductivity in order to secure other desirable engineering properties. This is especially true with certain materials that are used because of their refractoriness. Comparative insulating values of some commonly used insulating materials are shown in Table 1. In comparing the values presented in this table it should be borne in mind that heat conductivity varies with the mean temperature, with the overall density, and with the amount of moisture present. With fibrous or granular materials it varies with fiber or grain size and with the amount and kind of binder, if any is used. Under some circumstances it may vary with the arrangement of

Jan 1, 1949

History of Reverberatory Smelting in Montana, 1879-1933. By FREDERICK LAIST (Trans, vol 106 31,800 words ) The development of the art of reverbera¬tory smelting from 1879, when smelting first started in Butte, up to the present time is described. The paper traces the development of the reverberatory furnace, as regards both constructing and operating, from the initial 10-ton furnaces to the present-day 600-ton furnaces and the changes in operating practice which accom¬panied the gradual enlargement of the furnaces and the reasons therefor are described and explained The results obtained from an investigation (made in the course of the Carson litigation) into the various methods of charging reverberatory furnaces are given These investigations proved that the method of charging a reverberatory had very little to do with its performance It was also found, at the same time, that the depth and extent of the bath maintained in the furnace had very little to do with its performance Numerous operating results are included and the article is illustrated Development of Copper Converting at Butte and Anaconda. BY WILLIAM KELLY AND FREDERICK LAIST (Trans , vol 106 4400 words.) This paper is based on recollections of one of the authors, W M Kelly, who has been identified with the development of smelting and converting at Butte and Anaconda since early times The article starts with a description of the circumstances surrounding the first intro¬duction of copper converting at the Parrot Works in Butte under the Manhes patents It briefly recounts the difficulties which were encountered and the steps taken to overcome them Among these were the absence of means for punching tuyeres in the original converter This difficulty was overcome crudely by drilling holes in the windbox opposite the tuyeres, said holes being closed by wooden plugs Later these plugs were replaced by steel slides and still later by the Dibblie ball valve, which has remained standard ever since The development of the converter from both struc¬tural and operating standpoints is traced from the early beginning to the present day Developments in Lead and Copper Converting at Tooele. BY B L SACKETT (Trans, vol 106. 3900 words) This paper shows the development at this Utah lead and copper smelter from separate converting of the two kinds of matte produced to a more efficient and economical treatment of the combined mattes This was accompanied by the use of relatively large amounts of silicious ore in the converting of lead matte as well as copper matte, which greatly improved the quality of converter slag produced, both from the standpoint of its copper content and its desirability for

Jan 1, 1935

By R. Moldenke

Unlike the furnaces employed in the reduction of ores to mattes and metals, the foundry-cupola has only melting to do. This looks simple enough; and its development has progressed through centuries by cut-and-try methods; but there is still much to be learned concerning the causes which underlie the production of defective castings, even from first-rate materials. There are other differences between the smelter and the cupola. The former is usually, the latter rarely, run continuously. In the smelter there is some chance for experiment, since rich slags can be treated again; while in the cupola the metal must be good for casting from the first tap to the drop of the bottom ; otherwise, heavy damage will result. In the smelter, the object sought is the production of metal or matte with a minimum loss in the slag; whereas, in the foundry, a variety of castings of different compositions must often be run from the same heat, one after the other. Experience with the cupola has shown that the melting should take place, throughout the heat, in one zone, the zone of maximum temperature, which is clearly marked on the cupola-lining by the severe cutting action of the slag and iron oxide. The design and operation of the cupola must conform to this condition. This conformity having been secured, other considerations resolve themselves into those details of construction which will involve least trouble and cost of repairs. The very high temperatures required to melt iron and steel in the cupola, leaving the metal sufficiently superheated for casting, render the use of water-jackets inadvisable. It is always possible to patch up the lining at the melting-zone between daily heats; and the rest of the lining is seldom affected enough by abrasion and chemical action to require replacement oftener than once in nine months. The cupola is practically a shell of steel, lined with the proper refractory material, and provided with a sct of tuyeres for the admission of air to burn the fuel and melt the metallic

Jan 1, 1913

By M. W. Hayward

THE object of this paper is to record and tabulate the data and field observations obtained by the writers and their associates during 10 years of intensive study of lead-zinc deposits in the Cretaceous limestone areas in Northern Mexico, particularly in mines owned by the Cia. Minera de Peñoles, S. A. At the El Paso meeting of the Institute in October, 1930, J. G. Barry made the suggestion that a committee be appointed to correlate the ideas and theories which have been put forth by the numerous engineers and geologists who, during recent years, have made a study of the ore deposits in the area under consideration. The first step in a work of this nature would be to record all of the observed facts, and these facts would have to be accepted by those who attempted to formulate a theory of ore deposition. It is with this idea in mind that the writers have described as accurately as possible the actual, observed facts pertaining to the occurrence of the lead-zinc ores in dolomites or dolomitic horizons. By most writers the term "dolomite," is loosely used to designate magnesium-bearing limestones, regardless of the percentage of MgO present. Since no, true dolomites exist in the areas to be described, we shall also loosely use the terms dolomite or dolomitic limestone to designate those beds having a magnesia content of 5 per cent MgO or more. For a number of years the writers have been impressed with the fact that in areas where dolomite beds occur a large percentage of the lead ore is found in these beds, in spite of the fact that such beds may be overlain or underlain by pure limestone, which one would assume to be just as favorable for replacement as the dolomite, if not more 'so on account of its being more soluble in acid solutions than the dolomite. It is true that in some limestone areas, such as the Erupcion-Ahumada districts, Chihuahua, and Providencia, Zacatecas, where no dolomite beds have been found, large tonnages of lead ores have been mined. We venture to predict, however, that had there been dolomitic beds in these areas, the

Jan 1, 1931

By C. W. Crispell

The four nomograms presented in this article were designed to simplify and make more rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic sca1e. † For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Power foR CompREssion It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Fig. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: S X 144 PVn [(P')n-1/sn -1 (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, -in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 1, 1918

By R. S. Shoemaker, F. W. McQuiston

SOUTH AFRICAN MILLING PRACTICE All modern South African gold plants operate primarily on the principle of exposing the gold particles in the ore by fine grinding and then cyaniding the total pulp. Although there are minor variations and occasional depart- ures from established practices among the fifty gold mines in South Africa, the normal plant operations proceed as follows. After removal of waste rock by hand sorting (15Y0 on average) the ore is crushed in cone crushers to minus 1/2 inch and then ground to approximately 75% minus 200 mesh by milling with either rod, ball or pebble mills as primary units and pebble mills for the secondary grind. Classification in both circuits is almost invariably conducted with 20" cyclones of 30" or larger diameter. Gravity concentration in the milling circuit followed by barrel amalgamation of the concentrates is practiced in 70Y0 of the plants, particularly where the ore grade is high. A slightly better overall recovery is obtained than with direct cyanidation, but additional handling is involved. Johnson cylinder s , plane tables or belt concentrators, all lined with suitable types of molded rubber riffles, are used for this purpose. At all mines, cyanidation is the main process, usually conducted by continuous treatment in Pachuca tanks and pulp separation with rotary drum filters. Cyanide solutions contain about 0.0 1570 NaCN and require a protective alkalinity of 0.02070 CaO. Precipitation of the gold from cyanide solution is exclusively by zinc dust and lead nitrate using the Merrill-Crowe system in conjunction with Stellar pressure filters. The zinc precipitate is smelted, generally after a preliminary concentration by sulfuric acid, in electric furnaces, mostly submerged arc types, with a silica and borax flux, yield- ing a bullion of 8870 gold, 9% silver, and 370 base metals. The gold content of the ore varies between 0.20 and 1.0 oz Troy per short ton and extraction efficiency ranges from 9570 to 9870. In general, 4070 of the gold output is recovered by amalgamation and 6070 by cyanidation; but in some cases, it is entirely by cyanidation. Flotation has not been adopted for gold extraction as it has not proved as efficient as cyanidation. It is, however, often applied to ores containing higher than 1% sulfur for the recovery of pyrite for sulfuric acid production. On the eastern side of the Witwaters rand Basin, "run-of -mine milling” was introduced in 1960 and in three of the four mills in this area both sorting and crushing have been eliminated. The ore received from the shafts is conveyed to storage silos and then fed by Williamson automatic feed controllers to pebble mills ranging from 12 to 14 feet diameter, and 16 to 20 feet long. The pebble mills operate in closed circuit with 42 inch cyclones and the slime produced is thickened and cyanided in the conventional manner. No selective

Jan 1, 1975

By R. S. Shrode

By now most readers of this column are aware that it no longer has a regular editor. Tom Murphy, who did the job so well, has had to bow out because of his duties in Australia---duties that keep him from the luxuries of such things as typists and typewriters for rather extended periods of time. We will miss his regular contributions but hope and expect to hear from him as a guest columnist from time to time. Finding an editor to function on a regular basis turns out to be no simple task. This does not mean that there may not be candidates around who would secretly enjoy having their arm twisted into a "yes" position, but at the moment none has been found. Anyway, at the Salt Lake City business meeting it was agreed that we should try to spread the load around. To that end, the Regional Vice Chairmen were specifically singled out as one potential source of contributions. These fellows should have an opportunity for a hearing during their term in office. The existing organizational set-up of the IndMD Division may be a little unfair to this group of officers. The limited responsibility outlined in our Manual of Official Duties and Responsibilities does not offer them much chance for self-expression. Probably the by-laws were written so as to have a geographic representation of membership in case it should be needed at some time. But that is another subject. The point is that now these regional officers have an opportunity to speak out on topics of their own choosing through this column. Some have already done just that. There are also other potential contributors to the column. One is the Secretary, who twice a year uses the column for distributing the minutes of our business meeting to the members. Another is the outgoing Division Chairman. In Salt Lake City, it was decided that this officer should be challenged to contribute something each year as a means of reviewing events of the past year or explaining what should have happened but didn't. I am, therefore, trying to accept that challenge.

Jan 1, 1970

By L. C. Uren

THE resistance to flow of mixtures of gas and oil in passing up through the flow tubing of oil wells operated by gas-lift or by natural flow is a factor in oil-recovery technic that has received but little attention. Yet accurate design of a tubing installation for a particular set of conditions, where operation is by either of 'these methods, is impossible without quantitative data on the pressure loss suffered by the oil-gas mixture in its passage through the well tubing to the surface. Because of lack of such information, petroleum production technologists have been compelled to approach this problem by "cut-and-try" methods, which, doubtless in many cases, has resulted in the installation and use of tubing too large or too small for most efficient utilization of the expansive force of the gas used in lifting the oil. Impressed with the necessity for information of this character, the authors have conducted a series of tests with large-scale apparatus in the petroleum engineering laboratories of the University of California, designed to be productive of data that would afford a means of attacking the problem of flow-tubing design on a more scientific basis.

Jan 1, 1929

By L. O. Bieber, L. H. Martin

DIFFERENT MELTS OF THE same type of nickel and high-nickel alloys, while having almost identical mechanical properties at room temperature, may have widely varying hot malleability. Either the upper limit or burning temperature may vary or a variation in malleability may occur within the temperature limits normally encountered during hot working. Melts which have reduced hot malleability of the latter type, are said to have a "hot short" range. Examination of melting records and chemical analysis of these heats fails in most cases to show the reasons for these variations. In May, 1930, an investigation was started to determine if a quick and accurate method of hot-malleability testing could be developed which would predict the ability of the metal to withstand hot forging and hot rolling by standard mill practices. The results obtained were so satisfactory that from that time on, all melts of nickel and high-nickel alloys produced in the International Nickel Company's Huntington, W. Va. Works have been tested when hot malleabilty was an important factor. To date, over 63,000 commercial melts of Monelt † nickel, Inconel† and other high-nickel alloys have been tested and the test data compared with processing results. As the result of experience gained in over sixteen years, two standard methods of hot malleability testing have been adopted.

Jan 1, 1948

By H. A. Kortmann, K. Koch, B. M. Grover, O. P. Burghardt

Addition of lime, especially when treating a hematite feed, sometimes results in swelling and a severe loss in strength during reduction in the temperature range 900° to 1100°C and in grain disintegration in the temperature range 400° to 600°C in a weakly reducing atmosphere. Swelling and/or grain disintegration of pellets is often the reason for trouble in blast furnace operation, resulting in a decrease in the rate of smelting. Following a brief description of the test procedures employed (measurements of swelling, pressure-reduction-softening and grain disintegration), some results are given which were arrived at when testing pellets from industrial plants. Results of systematic tests are presented, where the effect of the quantity and quality of the gangue upon the behavior during reduction of pellets is illustrated. Varying amounts of quartz and limestone were added to a high-grade hematite ore and, then, pellets produced in a pot grate. The relationships of the behavior of the fired pellets during reduction are presented, among others, in the ternary system CaO-FeOn-SiOP. Finally, an attempt is made to explain the reasons for swelling, loss in strength, and grain disintegration.

Jan 1, 1974

By George S. Evans

Certain American operators bclieve that desulphurizing in the ladle offers a means of increasing blast-furnace and open-hearth yields with the possibility of improvements in quality of the steel. In fact, several producers have experimented with practically all of the known desulphurizing agents, including both standard grades of the alkalies and special preparations that have been offered from time to time during the past several years. Some of these are regularly being used today in large-scale commercial operations, with good results. Also, it is the practice to treat off-sulphur casts in the blast-furnace ladle at a number of plants. It is not known, however, that anyone in the steel industry (American) has ever adequately equipped a plant for desulphurizing blast-furnace metal in an efficient manner as regular operating practice. The purpose of this paper is to illustrate the importance of correct equipment and proper handling for obtaining uniform and efficient results. As will be shown, at the temperature of molten iron the alkalies are instantly neutralized by any free slag present, dissipating their desulphurizing value. Entrained silicates are rapidly washed out of the metal bath by the highly basic soda slags and will be satisfied ahead of desulphurizing reactions with FeS. More or less of the reagent will always be used up through reactions with the refractory lining. Desulphuriza-tion will be limited to the action of the free alkali then remaining in the slag. Causes for the erratic results generally found with desulphurizing tests in blast-furnace transfer ladles would include, among other things, variations in the quantity of furnace slag coming down with the metal, and differences in the percentage of kish and entrained silicates in the different casts. As the alkalies instantly unite with any free slags or silicates present, these, with any kish coming off, both dilute the reagent and reduce the surface contact between the slag and metal, thereby retarding the desulphurizing reactions.

Jan 1, 1938

By George S. Evans

Certain American operators bclieve that desulphurizing in the ladle offers a means of increasing blast-furnace and open-hearth yields with the possibility of improvements in quality of the steel. In fact, several producers have experimented with practically all of the known desulphurizing agents, including both standard grades of the alkalies and special preparations that have been offered from time to time during the past several years. Some of these are regularly being used today in large-scale commercial operations, with good results. Also, it is the practice to treat off-sulphur casts in the blast-furnace ladle at a number of plants. It is not known, however, that anyone in the steel industry (American) has ever adequately equipped a plant for desulphurizing blast-furnace metal in an efficient manner as regular operating practice. The purpose of this paper is to illustrate the importance of correct equipment and proper handling for obtaining uniform and efficient results. As will be shown, at the temperature of molten iron the alkalies are instantly neutralized by any free slag present, dissipating their desulphurizing value. Entrained silicates are rapidly washed out of the metal bath by the highly basic soda slags and will be satisfied ahead of desulphurizing reactions with FeS. More or less of the reagent will always be used up through reactions with the refractory lining. Desulphuriza-tion will be limited to the action of the free alkali then remaining in the slag. Causes for the erratic results generally found with desulphurizing tests in blast-furnace transfer ladles would include, among other things, variations in the quantity of furnace slag coming down with the metal, and differences in the percentage of kish and entrained silicates in the different casts. As the alkalies instantly unite with any free slags or silicates present, these, with any kish coming off, both dilute the reagent and reduce the surface contact between the slag and metal, thereby retarding the desulphurizing reactions.

Jan 1, 1938

By Richard A. Arterburn

For many years hydrocyclones, commonly referred to as cyclones, have been extensively utilized in the classification of particles in comminution circuits. The practical range of classification for cyclones is 40 microns to 400 microns, with some remote applications as fine as 5 microns or as coarse as 1000 microns. Cyclones are used in both primary and secondary grinding circuits as well as regrind circuits. The information given in this chapter is intended to provide a method, at least for estimating purposes, of selecting the proper number and size of cyclones and to determine the proper level of operating variables. Generally, it is recommended that cyclone suppliers be consulted for sizing confirmation. Sow cyclone suppliers employ digital computers to aid in the sizing and selection of cyclones. CYCLONE DESCRIPTION AND BASIC OPERATION Figure 1 shows a cutaway view of a typical cyclone. During operation, the feed slurry enters the cyclone under pressure through the feed pipe into the top of the cylindrical feed chamber. This tangential entrance is accomplished by two types of design, as shown in Figure 2. Since the majority of research has been done with the involuted type, the graphs and relationships shown may not be strictly applicable to other designs. As the feed enters the chamber, a rotation of the slurry inside of the cyclone begins, causing centrifugal forces to accelerate the movement of the particles towards the outer wall. The particles migrate downward in a spiral pattern through the cylindrical section and into the conical section. At this point the smaller mass particles migrate toward the center and spiral upward and out through the vortex finder, discharging through the overflow pipe. This product, which contains the finer particles and the majority of the water, is termed the overflow and should be discharged at or near atmospheric pressure. The higher mss particles remain in a downward spiral path along the walls of the conical section and gradually exit through the apex orifice. This product is termed the underflow and also should be discharged at or near atmospheric pressure.

Jan 1, 1982

By E. L. Bruce

GOLD occurs ill many mineral deposits in the rocks of the Canadian Shield. It is present in the ores of many base metals and a considerable quantity is recovered as a by-product from the production of copper at Noranda, of nickel and copper at Sudbury and of copper and zinc at Flinflon. But the greater part of the gold production of Canada is from deposits in which gold is the only metal of value. No gold is obtained from placer deposits within the borders of the Canadian Shield. A brief review of the geological relations of some of the gold deposits of the Canadian Shield will be presented in an attempt to explain certain associations. Only those which are being worked for their gold content will be considered and descriptions will be confined to representative types of deposits, chiefly those of major importance; a few others, differing in certain features from those of the older and larger mines, will be included in order to illustrate the general conditions in which gold occurs in these ancient rocks. Brief summaries will be given of the geological relations of the Beattie and Siscoe mines of northern Quebec, of the mines of the Porcupine and Kirkland Lake areas of northeastern Ontario and of the Howey, Central Patricia and Little Long Lac mines of northwestern Ontario. Genetic relations to igneous rocks of granitic composition, outcropping in the vicinity, have been assumed for many of these deposits. Undoubtedly the ore minerals have been derived from igneous sources and, for some occurrences, there is evidence suggestive of genetic relationship between the ore bodies and neighbouring intrusive rocks. During the past few years, however, many investigators have expressed doubt of the genetic relationship of certain ore bodies to igneous masses near which they occur. As will be seen from references in the following descriptions the importance of the structural conditions in localizing deposition has been realized. This is pointed out for Canadian pre-Cambrian gold deposits by E. T. Dougherty, who also refers to the

Jan 1, 1937