Search Documents

By Oliver Bowles

WHILE vast quantities of limestone and dolomite. are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone' for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

Jan 1, 1928

By Worthen Bradley, R. G. Hall

THIS paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer to the Bradley Mining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a rotary kiln at the same end-that is, of course, the upper end. This is as opposed to "counter-current firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. EARLY REFERENCES The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,1 its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver . . . is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and flies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake County, California. The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank. Reed and Sulphur Bank ranked respectively fifth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: Sometimes there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of . . . the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away. as its richness and value were not

Jan 1, 1945

By Edwin C. Eckel

The title of this study may fairly lead to misunderstanding unless its basal viewpoint is explained at the start. There is of course no chance of misunderstanding the term strategic minerals-for some years past it has been rather generally used to cover those mineral supplies, important for war use, which do not occur in adequate amount on the territory of the Power under consideration. Even here, however, I might add a note of warning. It is commonly understood that the list of strategic minerals will vary, according to what country we are considering; but it is rarely understood, even in Staff studies, that it varies equally according to the particular adversary we happen to be considering. In the present study I have stated the definition in the broadest possible terms, and have at this stage purposely avoided limiting it to any one country or war situation, with the express purpose of being free to bring out certain implications which are commonly, if not always, overlooked. The more important opportunity for misunderstanding is, of course, that my views on the phenomena war and peace do not coincide with those currently fashionable, particularly in advanced intellectual circles. For we must face the fact that for a decade past the natural reaction from war conditions has shattered the public mentality so completely that our public discussions of such questions have very little relation to fact; they are excursions into ideal rather than Realpolitik. And as such they serve merely to prevent public discussion or accept-

Jan 1, 1932

By Roshan B. Bhappu, George M. Potter

The chemistry involved in the recovery of gold and silver from natural resources through hydrometallurgical and pyrometallurgical processes is reviewed. Process metallurgy for the cyanidation, activated carbon adsorption, carbon stripping, and electrowinning of gold and silver is discussed. The application of zinc sodium sulfide use for silver recovery from cyanide solutions is covered. Electrooxidation, other oxidation methods and roasting processes for problem ores and concentrates containing organic carbon and impurities such as arsenic, antimony, and tellurides are summarized. The smelting of cathodes, precipitates, and other products, and the various wet and furnace steps in separating dore metal are also reviewed.

Jan 1, 1981

By C. W. Hall

Owin to its isolation and comparatively small tonnage, the Yoquivo district is not widely known; though financially important andgeologically, quite interesting. San Francisco de Yoquivo, the center of the mining district, is in the western part of the state of Chihuahua, Mexico; about 35 miles west of San Juanito, on the Kansas City, Mexico & Orient R. R. The town can be reached from the railroad by a good trail over a rugged country. The elevation of Yoquivo is 6500 ft., and peaks surrounding the town are 2000 ft. higher. The mining towns of Concheño and Ocampo are 25 miles northwest, and Uruachic is 20 miles southwest. The climate, temperate and healthful, is almost ideal. The rainy season begins in July and ends the latter part of September. There is usually, though not always, some precipitation in all months except April, May, and June. The mountains are covered with pine and scrub oak. Water, wood and lumber are plentiful for all ordinary purposes, and hydroelectric power is available for about six months of the year, when wood for steam power is utilized as an expedient. The district has been worked recurrently for over 60 years. The Yoquivo province lies on the steep western slope of the Tara-humara division of the Sierra Madre range of mountains. The province is traversed by many deep canyons, most of which flow west. The town is situated on the San Francisco arroyo, which makes a confluence with the Huevachic stream 236 m. southwest; the Huevachic in turn joins the Candemeña river farther down and these two drain the western flank of the Tarahumara mountains and form the headwaters of the Mayo river. The claims of the Yocluivo Development Co., which is the only organization in the district with a record of any considerable production, lie within an area roughly l½ m. square. Thc area extends from the San Francisco arroyo north, and from the Dolores arroyo west, and is confined to the andesite formation. General Geology The terrane about Yoquivo is composed of a series of Tertiary eruptives that consist of numerous phases of andesite and rhyolite, and

Jan 1, 1927

By L. E. Schiffman

This paper describes the operation of two kerosine flotation plants in Alabama for cleaning -10 mesh bituminous coal. One plant treats washer sludge, the other raw coal. Data on capacity efficiency and capital and operating costs is given. Methods for increasing cell capacity are discussed.

Jan 10, 1950

By M. J. Spendlove, H. W. St. Clair

The problem frequently arises, particularly in refining metals or smelting scrap metals, of separating metals in the metallie state. Many metals may be separated by taking advantage of their difference in vapor pressure. Such separations can be made at atmospheric pressure, but the separations are much more selective and can be carried out at considerably lower temperatures if the distillation is done at pressures of a few millimeters or less in an evacuated enclosure. Until recently, this has not been considered feasible as a metallurgical operation, but the recent improvemcnts that have been made in vacuum technology have broadened the applicability of vacuum processes and have prompted re-examination of low-pressurc distillation of metals as a practicable process. The distillation of zinc from lead is one separation that has already been reduced to practice.l This paper is the first of a series of studies being made on separation of nonferrous metals by distillation at low pressures. Although these experiments were confined to the separation of zinc from aluminum, the significance of the results is by no means confined to these two metals. The purpose has been to investigate a metallurgical technique rather than merely to devise a means of separating specific metals. The experimental work on distillation of zinc from zine-aluminum alloys at reduced pressure grew out of earlier work on distillation at atmospheric pressure.2 The earlier work indicated that it would not be practicable to decrease the zinc in the alloy much below 10 pct owing to the high temperature required. Therefore attention was turned to distillation ah low pressures, at which lower temperatures are required. After preliminary tests were made in a small, evacuated tube furnace, a larger furnace having a capacity of 100 to 150 Ib of metal per charge was constructed. Distillation tests were first made on pure zinc and then on aluminum-zinc alloys of various composition. Particular attention was given to the limit to which zinc could be reduced in the residual metal. Data were also taken on the rate of evaporation, and heat balances were made for both the crucible and the condenser. Distillation Furnace The vacuum-distillation unit is illustrated schematically in Fig 1. The major components are the induction furnace, the condenser, the vacuum system, and the power-conversion unit. Power is supplied to the induction furnace from a 50-kw 3000-cycle motor-driven alternator. The pressure in the furnace is reduced by a vacuum pump having a nominal pumping speed of 10 liters per sec. When in operation, the metal vapors travel upward from the furnace to the water-cooled condenser where they are collected in amounts of 50 to 100 lb. The condenser is removed with aid of an electric hoist. When the system is under vacuum, the condenser is made self-sealing by a rubber gasket between the smooth-faced, water-cooled flanges at the top of the furnace and the bottom of the condenser. The pressure of the atmosphere is more than sufficient to insure sealing. At the conclusion of an experiment, the residual metal can be removed from the furnace by removing the condenser and tilting the furnace with the electric hoist. The metal was cast into the molds carried on a mold truck. A photograph of the furnace and auxiliary equipment is shown in Fig 2. The details of the vacuum furnace are illustrated in Fig 3. The furnace proper is made vacuum-tight with rubber gaskets placed at each end of a fused quartz cylinder. A clamping plate at the bottom and a ring at the top are made to squeeze the rubber between the metal and the end of the quartz tube. A large graphite crucible placed inside the quartz cylinder is thermally insulated and physically supported by refractory insulating bricks. A thermocouple in a quartz protection tube is located at the bottom of the crucible: the leads pass through a rubber seal in the bottom plate. The supporting structure for the furnace is an angle iron frame with transite board sides. The condenser is made in the form of a water jacketed cylinder with an opening to the vacuum line at the top. The bottom has a projecting skirt inside the machined flange to provide additional cooling for the rubber gasket. Condenser sleeves are made in the form of two semicylindrical pieces of sheet metal that fit snugly inside the cooling jacket. The split sleeve facilitates removal of the condensate. Measurement of Temperatare and Pressure The metal temperature was measured by a platinum-platinilm rhodium thermocouple inserted in a well extending up into the bottom of the graphite crucible. During rapid evaporation there is a wide difference in temperature between the surface and the main body of metal in the crucible because of the large amount of heat that must be conducted to the surface to supply the heat of evaporation. The heat of

Jan 1, 1950

By Eugene A. Stephenson

Critical analyses of the work expended in producing oil by the utilization of gas energy have appeared in the publications of Shaw,' Pierce and LewisI2 and Herold,3 authors who have ably discussed the factors which must be taken into consideration in comparing energy consumed per barrel in various wells which are flowed by means of gas-lift. However, two distinct phases of oil production are concerned with the ratio of gas energy consumed to oil produced. One of these phases is the gas-lift, which utilizes the differential gas pressures for the purpose of flowing oil, whether these pressures be natural reservoir pressures or be induced by artificial compression of gas or air. The other phase has to do with prorating oil production in pools which are operated either as units, or are subject to such restrictions as those imposed at Oklahoma City by the Corporation Commission, or by similar controlling groups in other fields. An abundance of literature is available relative to the problems of flowing wells by gas-lift, but the first suggestion that the energy of the gas within the oil and gas pool might serve as a basis for proration, appeared in the timely article by Mc Williams.4 Much of the dissatisfaction with proration in certain fields arises because some operators feel that besides the hazard to the wells which accompanies the test, the method of allocating production on the basis of the " potential" gage is inequitable and gives some operators a distinct advantage over others.5 The most severe penalty may be exacted from the most progressive operators or those who attempt to produce their oil with a minimum quantity of reservoir gas. If no difficulties ever developed in drilling, shutting off water, or in well completion, it might

Jan 1, 1931

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

By J. R. Hoffert

ON Oct. 27, 1941, the Sanitary Water Board of the Commonwealth of Pennsylvania called a meeting of the representatives of the coal operators in the Schuylkill River Basin, and frankly suggested to the operators that they "clean up their house" before someone else came in and did it for them; that they should not emulate the railroads with their "public be damned" policy and its fateful results. It had been four years since the passage of the antipollution law of 1937, a law which exempted silt from collieries until such time as a practical method existed for the removal of their water polluting properties. It had been fifteen long years since Sisler, Frazer and Ashmead concluded that 900 million tons of culm and silt had been deposited in Pennsylvania's streams in the process of preparing five and a half billion tons of anthracite for the world's consumers. Fine coal was being "mined" in the streams by "washeries" and river dredges downstream from the collieries, and silt banks no longer held back the endless black stream entering the Schuylkill at the rate of 350,000 tons per month. The coal operators were apparently working on the outmoded assumption that each ton of fine coal prepared displaced a ton of larger sized, more profitable coal. The meeting between the Sanitary Water Board and the coal operators signaled the beginning of the end of Pennsylvania's pollution problems. As a result a committee was formed at that meeting by the operators to find out what conditions were at each colliery. The Bureau assisted in the indication of methods of measurement and sampling and in the development of forms for reporting the needed data. One large producer had its chief engineer supervise the gathering of the information concerning the quantity of waste waters, the amount and sieve analyses of the waste solids, and the existing means for retaining

Jan 3, 1950

By D. H. Yardley

GEOCHEMICAL investigation of trace elements in surface materials was begun near Ely, Minn., in 1953 along the basal contact of Duluth gabbro with Giants Range granite (Fig. 1). This article presents data on the distribution of copper and nickel in till and in stream sediments in the area and proposes an explanation for the types of distribution found. The Duluth gabbro, one of the world's largest basic intrusives, intrudes rocks which range in age from Keewatin to middle Keweenawan. Within the test area the gabbro is in contact with granite except for short sections where it is in contact with remnants of iron formation. Sulfide mineralization occurs within the gabbro, near and parallel to the basal contact for a distance of several miles. Schwartz and Davidson1 have described the geologic setting of the mineralization.

Jan 7, 1958

By Donald F. Irwin

Amid the violent economic changes of recent years that have affected Canadian gold-mining operations so deeply, the discovery and early developments of Kirkland Lake might easily be overlooked. There was more than one "false dawn" for the district before developments finally established the fact of a superb mineralized zone extending through the present operating properties. Never far from the railway, Kirkland Lake has had the benefit of direct rail service for many years. The pioneer discovery on which the first mill and cyanide plant was erected was the "Tough-Oakes," this property being on what is now the eastern end of the producing area; some time later, the "Lake Shore" was discovered at the present center of the district, and a small plant was built upon it also. Both of these early treatment plants were of pre-war design. Progress in gold metallurgy has caused a gradual change in cyanide practice since the early days at Kirkland Lake, which may be observed in the various plants now operating there. From the beginning, it was recognized that Kirkland Lake ores were more responsive to cyanidation than to alternative recovery methods, and that their mineralization contained gold in very finely divided form. Although sulfides and tellurides are present, the quantity is small, being in the order of 1 or 2 per cent by weight, so that gravity concentration is undesirable, since gold is not confined to the sulfides. Some complication is offered by the presence of tellurides, which have caused lengthy controversy over their importance in recovery methods, but which are now generally regarded as less harmful in the light of increasingly high recoveries being obtained. Nevertheless, finely divided gold intimately associated with sulfides in the presence of tellurides; and occurring in the hard Kirkland Lake porphyry ore, substantially free from natural slime-forming constituents, indicates fine grinding. This has been the universal practice although the degree of grinding has varied a little among the different mills and is considerably finer now than formerly. The natural condition as outlined caused the establishment of fine grinding at an early stage in the development of Kirkland Lake, during the period of valuation of gold at, $20.67 per ounce. With the arrival

Jan 1, 1935

By James B. Graham, Earle E. Smith

The value of all minerals produced in the United States for the years 1930 to 1932 averaged $3,460,000,000 annually, according to Bureau of Mines reports. Of this amount, approximately $1,280,000,000 represents nonmetallic substances, such as petroleum, gas, sulfur and salt produced as fluids. Thus, about.37 per cent of the country's mineral wealth is procured through wells drilled in the earth, which require casing to keep them open throughout their life. Deep well drilling has increased greatly in the last few years. Several strings of casing have been set deeper than 9000 ft.—one, a string of 7?-in. O.D. casing, 10,301 ft. long, run in a well drilled by the Gulf Production Co. in West Texas, holds the record up to this time. These are longer strings than were contemplated when the American Petroleum Institute Specifications were adopted 10 years ago, therefore it is necessary to consider whether the present joint standards are adequate for such strings, or for even longer strings that may be called for in the future. Petroleum engineers are asking: Is there a possibility that stronger joints can be designed without going to stronger and more costly steels than offered in present specifications? Without sacrificing too greatly the tensile properties of the joint, can its design be changed to allow more clearance in the open hole below the next larger string of casing, and thus avoid costly underreaming? What can manufacturers offer for drilling through heaving shale? Fundamentals of the Problem During the last few years considerable study has been given to casing joints and their limitations, and since attention must be given to this subject by those who will be required to drill deeper holes, it is timely to review the fundamentals of the problem. These will be recognized generally as the following: 1. No threaded joint can be stronger than the area of metal under the root of the first perfect thread, and this area must be large enough

Jan 1, 1935

By S. N. Dixon

Sampling and assaying procedures were developed to obtain unbiased and reasonably accurate Au grade estimates in drill samples fm a coarse gold deposit. Gold grade comparisons were made by assaying 3 (1 assay ton) splits from each drill interval, then processing the entire reject thru a pilot plant for a blocked out zone. The result comparing the assay splits to the pilot plant results gave a ratio of 1 to 1.07. Another technique was developed to detect drill samples which has a coarse gold content by monitoring the varience. Testwork could be done on a 1 kg sample to improve the accuracy of the grade estimation if the variance was high for a drill interval.

Jan 1, 1984

By J. D. Braun, C. W. Powell

Diffusion between gold and indium at two temperatures below the melting point of indium (155.4oC) was investigated. The major, component of the diffusion zone was determined to be AuIn2; the other, intermediate phases in the system occur in much narrower layers In order of decreasing layer width these are: Au9In4, AuIn, Au4In. Inter diffusion coefficients of the four intermediate phases and the terminal solid solutions lie in the range of 2.4 x 10-l3 to 1.8 x 10-11 sq cm per sec. WHEN two metals which do not form a continuous series of solid solutions interdiffuse, each phase in equilibrium at the diffusion temperature should appear as a separate layer in the diffusion zone. In the Au-In system, diffusion plays a significant part in many commercial applications, particularly where indium alloys are used as solders for electrical contacts with very fine gold wire, for estab- lishing electrical contact to thin metallic films, and for mounting metal-coated piezoelectric crystals. A knowledge of the number, extent, and type of phases which form at diffusion temperatures below the melting point of indium, 155.4oC,1 and the diffusion constants for the system would be useful for these practical applications. Of more basic significance, additional information on polyphase diffusion in a system not previously investigated would be gained. The phase relationships in the Au-In system were determined primarily by Kubaschewski and Weibke1 and are based on thermal, microscopic, and X-ray analysis, Fig. 1. There are five intermediate phases in the system having approximate compositions corresponding to the formulas: Au4ln (ß)—80.0 at. pet Au; Au3In (?)— 75.0 at. pet Au; Au9In4 (d)—69.2 at. pet Au; AuIn—50.0 at. pet Au; AuIn2—33.3 at. pet Au. Solid solubility of indium in gold at 700°C is reported as 12.64 at. pet and at 406°C as 10.36 at. pet. No solid solubility of gold in indium is reported.

Jan 1, 1964

By L. R. Page, J. J. Norton

EFFECTIVE methods for determining grade and reserves of pegmatites in advance of mining have been developed in recent years. When intensive work began on the economic geology of pegmatites during the early years of World War 11, it was widely believed that grade and reserves could be estimated only in a most general way. The literature indicated that not all pegmatite deposits are unpredictable, but statements emphasizing unpredictability and irregularity seem to have been more widely accepted. Many standard references reflect the prevailing opinion that minerals: are unsystematic in their occurrence in pegmatites. Pegmatites have been described as "notorious for their irregular structure," and minerals within pegmatites as "irregularly distributed." "irregularly disseminated," of "erratic occurrence," "proverbially erratic in distribution," "characterized by extreme irregularity in ... size and distribution of the essential minerals, and variety and proportion of the accessory minerals," and "spotty.'"" Over many years, however, geologic techniques have been applied with increasing success to economic analysis of pegmatites. Investigations, chiefly since 1939, have shown that mineral distribution and structure of pegmatites are largely systematic and that detailed geologic study can be used to predict the size and shape of mineral deposits in pegmatites. Because the writers are most familiar with the pegmatites of the Black Hills, S. D., examples cited are from that area." Pegmatites mined in other dis- * All examples are described more cornpletely elsewhere.: tricts are similar to those in the Black Hills," and the techniques described here have been applied by geologists and engineers working in other districts. In actual practice few pegmatite mine operators attempt to make accurate estimates of grade and reserves in advance of mining. Many deposits are too small for mining except on a very small scale; few pegmatite mines have more than ten employes. Hence there is little systematic preparation for mining, and the capital outlay may be so small that only a general knowledge of reserves is necessary. Technical personnel are rarely employed by pegmatite mine operators to make such estimates. In the future, however, as capital outlay becomes larger, estimates of grade and reserves will have to be more accurate. Geologic Aspects of Determining Grade and Reserves Estimating grade and reserves requires that the type of pegmatite, the size and shape, and the internal structure be determined by detailed geologic mapping and careful mineralogic study. The wide variations in the texture and distribution of minerals within many pegmatite deposits make a thorough geologic study of this kind necessary before it is possible to decide what sampling methods should be used to determine mineral content or grade. Types of Pegmatites: The first step in economic appraisal of a pegmatite is to determine the min-eralogical and structural type. In general, pegmatites may be classified into two groups: 1) those in which component minerals are more or less evenly distributed throughout the entire body and show relatively minor variations in texture, and 2) those in which component minerals have been segregated into units with recognizable differences in texture, mineralogy. or both. Johnston" has classified these types of pegmatites as homogeneous and heterogeneous, respectively. Cameron et al.10 have used the terms ~inzoned and zoned for similar types. The difference between the homogeneous and heterogeneous types is of great commercial importance. Homogeneous pegmatites can seldom be mined where the products are concentrated by the hand methods now commonly used, but they have been mined in a few places where a milling process has

Jan 1, 1957

By F. V. Lenel, G. S. Ansell, J. A. Dromsky

The growth of aluminum oxide particles in a nickel matrix was studied eve?. the temperature vange of 2140° to 2470°F. The instability of the dispersed alumina was shown to be independent of the crystal structure of the alumina. The activation energy for the growth of the dispersed alumina was found to be 84.7 1 2.0 kcal. The particle radius increased as a function of time. These results indicate that the growth is not diffusion controlled. It is believed that the rate controlling mechanism is the dissolution of the aluminum and oxygen atoms into the nickel lattice. THE strength properties of alloys which consist of a finely dispersed second phase in a metallic matrix depend upon the spacing between the second phase particles. It is therefore desirable to achieve very fine dispersions in these alloys. Furthermore, to retain the properties these very fine dispersions must be stable during fabrication and service of the alloys. The best known of the dispersion strengthened materials, the SAP type alloys, which consist of a dispersion of aluminurn oxide in aluminum, have exceptionally good stability up to the melting point of aluminum. There is evidence, however, that other dispersion strengthened alloys, even those consisting of refractory oxides in a metal matrix, may be less stable. This investigation is concerned with the stability of Ni-Al2O3 alloys in the temperature range in which these alloys are usually fabricated. The mechanical properties of Ni-Al2O3 alloys at elevated temperatures have been previously investigated by Crelnens and rant,' and Gregory and Goetzel.2 The behavior of these alloys in stress rupture tests appears to indicate that at temperatures below 1800°F they are highly stable. There is some doubt, however, as to their stability at the higher temperatures used during the conventional fabrication. Cremens and Grant, in preparing their test alloys, cousolidated, by powder metallurgical techniques, nickel powders as fine as 0.13 µ diam and alumina powders as fine as 0.018 µ. Metallo- graphic examination of the alloys following fabrication revealed that none had interparticle spacings of less than 2 µ. Considering the size of the original component powder particles, it is likely that the dispersions coarsened during fabrication. Gregory and Goetzel, in their studies of extruded alloys of 80 pct Ni—-20 pct Cr matrixes with nonmetallic dispersion, observed a definite coarsening of the alumina dispersions in alloys sintered at 2280°F as cantrasted to those sintered at 2000oF. Similar observations on the spheroidization and growth of thoria particles finely dispersed in a nickel matrix were made by D. K. Worn and S. F. Marton.3 As a result of such coarsening, much of the effort expended in the preparation of very fine powder mixtures would be lost. The mechanical properties of the alloys which had experienced coarsening would be expected to be poorer than if the original dispersions had been retained. EXPERIMENTAL PROCEDURE Ni-Al2O3 alloys were produced from powder prepared by a coprecipitation technique. Aluminum hydroxide and nickel hydroxide were coprecipitated from chloride solutions of the metals. The mixed hydroxides were calcined to form metal oxides and the nickel oxide in the mixture was selectively reduced to nickel by treating it in hydrogen. Specimens were compacted from the resultant powder which consisted of a fine, uniform mixture of aluminum oxide and nickel particles. The compacts were sintered by resistance hot pressing4, a densification technique which requires exposure times of the order of only a second or less at elevated temperatures. A conventional sintering process was not used, since the temperature required for densification would have to be in the region in which the stability of the dispersion was to be studied. A series of hot pressed specimens were treated in hydrogen at temperatures from 2140o to 2470°F (1171o to 1355oC, for times up to 120 hr. Changes in the microstructures were studied by electron microscopy using the two-stage preshadowed carbon replica method.5 In performing a lineal analysis on a series of micrographs from each specimen it was found more convenient to determine the mean free path between alumina particles rather than particle radii as the parameter of growth. Although these quantities are directly proportional for only spherical particles, the alumina particles in these alloys

Jan 1, 1962

By E. N. Silverman

Mixtures of' MnS, ZFeO-SiO,, ZMnO.SiO, FeO, and MnO were prepared synthetically and used to study the planes ZFeO. Si0,-ZMnO.SiO,-MnS, FeO-MnO-MnS, and Fe0-MnO.Si0,-MnS in the quaternary system. Because the oxides and silicates studied flux MnS, inclusions in this system are partly liquid during rolling. Also, oxygen can modify subsurface inclusions through the reaction MnS + FeO—FeS + MnO during the soaking of ingots and the reheating of blooms and billets. NONMETALLIC inclusions in steel have long been a subject of study and conjecture because the properties of many steels are known to be affected by the the kind and amount of inclusions present. In free-machining steels, the type of inclusion present has a direct bearing on their machinability; in other steels, cleanliness is important and metallurgists direct their efforts at reducing the amount of non-metallic inclusions. Thus, the accumulation of knowledge about the formation and behavior of inclusions during all stages of steelmaking and processing should aid in improving the quality of steels and decreasing the production costs resulting from rejections. Previous studies of inclusions have contributed greatly to our understanding. The investigators have generally examined inclusions in finished steel. Boulger, Moorehead, and Garvey1 found that in Bessemer steels, low silicon contents results in globular sulfide inclusions with attendant high machin- ability ratings. Van vlack2 also found that low silicon contents favor inclusion morphology that contributes to high machinability ratings. Boquist and Stoll* found that silicon content affected sulfide inclusions and machinability of blooms, billets and bars more than did the finishing temperature in the range between 1775° and 2075°F. Carney and Rudolphy3 studied the distribution of sulfur, manganese, silicon, and carbon in a commercial ingot of resulfur-ized steel and found that silicon was concentrated near the bottom. This helped to explain why bottom cuts had poorer machinability. Klinger and Koch4 developed techniques for extracting inclusions from steel, and the technique devised by Gurry, Chris-takos, and stricker5 for extracting carbides can also be adapted to the study of inclusions. A different approach to the study of inclusions in steel consists of synthesizing the constituents that form inclusions and determining the phase eauilibria in the system that contains the constituents. The resulting phase diagrams can then be used to determine the effect of the various constituents upon each other. In this way, it becomes possible to under-

Jan 1, 1962

By B. M. Larsen, T. E. Brower

In an earlier paper1 we discussed a simple, rapid method of taking samples of liquid steel and analyzing them for oxygen, which, though possibly not absolutely accurate (as is likewise true of all other methods), certainly yields results that are satisfactorily consistent. Accordingly, samples from hundreds of heats ill different shops were analyzed for oxygen, with results sufficient in number to be handled statistically and permit estimation of some general trends. Measurements were made in acid as well as in basic open hearths, throughout the refining period, to learn how stirring, blocking, adding ore or lime or sand, affects the oxygen content of the bath; we also followed the changes brought about by tapping, teeming, and deoxidizing. Some of these results, discussed in an earlier paper,2 bring out the dominant role of the carbon-oxygen reaction in regulating degree of oxidation both of metal and of slag, also the marked variability of concentration of dissolved oxygen [0] in excess of that which would be in equilibrium with carbon and with carbon monoxide at a partial pressure of one atmosphere. As a logical beginning on this complex problem, we take up in the present paper the variability of this excess oxygen, A[O], when other factors are as constant as they ever are in open-hearth operation; namely, toward the end of the refining period, when the bath may be regarded as in the comparatively steady state it approaches in absence of disturbing factors. This condition was chosen because by that time the significant reactions, except carbon oxidation, between slag and metal have come to substantial equilibrium; this facilitates interpretation of the complex situation and thus perinits more definite conclusions to be drawn. This excess concentration of oxygen, A[O], in the metal is needed, of course, to make the steelmaking process go at a reasonable rate; alternatively it may be regarded as a measure of the virtual pressure increment above one atmosphere, or of the degree of supersaturation, of carbon monoxide in the metal. According to our measurements, the excess concentration A[0] in liquid steel varies from about 0.009 to 0,035 per cent oxygen by weight. It is quite sensitive to change of conditions, being altered temporarily by operations such as stirring with green poles, additions of ore, lime, or sand; but as the disturbance works itself out, it resumes a level within the intermediate range characteristic of the steady state. The conditions most common in average furnace practice are covered by the following: i[O] Usual Per Cent Oxygen by Conditions Weight 1. Vigorous lime boil........... o.oog-0.01s 2. Steady state................ o.or;-0.025 3. Working of ore.............. o.023-0.035 Thus when the bath can be regarded as in a reasonably steady state—that is, when it is boiling normally, is at proper temperature with a well-shaped slag, and has been free from disturbing effects during the preceding half hour—A[0] returns from

Jan 1, 1948