Search Documents

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By F. P. Nichols, F. A. Renninger

At one time, mineral aggregates were considered physically and chemically inert substances whose junction was that of an inex-pensive, easily obtainable source of bulk. This philosophy applied regardless of the use to which the aggregate was put. Research approaches dealing only with such gross physical properties as hardness, toughness, impact resistance, etc., dominated the early growth years of the industry and influenced specifications to a large extent. The accelerated pace of highway construction, which began toward the end of the depression years, focused attention on the need for extensive aggregate research. The realization in the early 1940's that aggregates interacted chemically as well as physically with their environment provided the stimulus necessary to translate the drab, systematic aggregate technology of the early 20th century into the changing, dynamic, challenging field it is today. Current research problems are discussed in detail. These efforts being pursued by contract research organizations, universities, governmental agencies, and industry transcend many fields. The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Almost 2 billion tons of mineral aggregates are quarried or mined, processed, and sold yearly in the United States alone.= The largest uses to which this vast tonnage is subjected are as ingredients of portland-cement concrete, bituminous concrete, and dense-graded aggregate-base course mixtures in the highway and building construction fields, two industries closely related to the expenditure of public funds. It is for these uses, partially in justification for the expenditures of vast sums of public funds, that mineral aggregate research truly finds its emphasis. The research efforts expended relative to the highway and building construction uses to which mineral aggregates are subjected are those of primary concern to the industry. These efforts, while of direct consequence to the industry due to the volume market represented, are of interest as well to public agencies, universities, and contract research firms. All actively conduct research, exchange information, and make contributions to the overall knowledge relative to aggregate usage and limitations. The research efforts of the mineral aggregate industry is the subject to be discussed throughout this paper. It covers all aspects of highway and building design, construction, and technology. The effects of research pertaining to quarrying and mining methods, blasting and processing techniques, storage and handling facilities, and equipment employment and development have left their mark on the crushed stone and sand and gravel industries. Such specialized efforts have resulted in dramatically increased production rates which in turn have served to keep costs, and hence prices, down. Despite the many inflationary pressures over the years, the cost of a ton of aggregate today is little more than it was 25 or 30 years ago. Mention is made of these efforts simply to emphasize the diversity of research in the mineral aggregate field. The remainder of this paper focuses on the complexity of what might be termed "product knowledge" research.

Jan 1, 1971

By J. R. Szedon, T. L. Chu, G. A. Gruber

Amorphous adherent filnzs of silicon dioxide have been deposited on silicon substrates by the oxidation of silane at temperatures ranging from 650 to 1050C. Various diluents (argon, nitrogen, hydrogen) were used to suppress the formation of SiO2 in the gas phase. Deposition rates of the oxide were determined over the temperature range in question as functions of' re-actant flow rates. Etch rate studies were used for a cursory comparison of structural properties of deposited and thermally grown oxides. From electrical evaluation of metal-insulator-silicon capacitors it was determined that the interface charge density of deposited films is similar go that of dry-oxygen-grown films in the 850° to 1050 C temperature range. Deposited films exhibit several ionic instability effects which differ in detail from those reported for thermal oxides. Stable passivating films of silicon nitride over deposited oxides appear to be practical for use in silicon planar device fabrication. Such films can be prepared under temperature conditions which have less effect on substrate impurity distributions than in the case of grown oxides. AMORPHOUS silicon dioxide (silica) is compatible with silicon in electrical properties and is the most widely used dielectric in silicon devices at present. Silica films can be prepared by the oxidation of silicon or deposited on silicon or other substrate surfaces by chemical reactions or vacuum techniques. The ability of thermally grown silicon dioxide films to passivate silicon surfaces forms one of the practical bases of the planar device technology. Properly produced and treated films of grown SiO 2 can have low densities of interface charge (-1 X 10" charges per sq cm) and can be stable as regards fast migrating ionic sgecies. 1 To maintain these properties, even with an otherwise hermetically sealed ambient, the Sia layers must be at least l000 A thick. Such thicknesses require oxidation in dry oxygen for periods of 7.8 hr at 900°C or 2 hr at 1000°C. Although oxidation in steam or wet oxygen can reduce these times to 17 and 5 min, the resulting oxides must be annealed to produce acceptable levels of interface charge., Oxidation or annealing involving moderate to high temperatures for extended periods of time can be undesirable. Under some conditions, there can be changes in the distribution of impurities within the underlying substrate. A chemical deposition technique using gaseous am-bients is particularly attractive and flexible for preparing oxide films. With a wide range of deposition rates available, films can be produced under condi- tions of time and temperature less detrimental to impurity distributions in the silicon than in the case of thermal oxidation. The pyrolysis of alkoxysilanes, the hydrolysis of silicon halides, and various modifications of these reactions are most commonly used for the deposition of silica films.3 Silica films obtained in this manner are likely to be contaminated by the by-products of the reaction, organic impurities, or hydrogen halides. The use of the oxidation of silane for the deposition process has been reported recently.4 The deposition of silica films on single-crystal silicon substrates by the oxidation of silane in a gas flow system has been studied in this work. The deposition variables studied were the crystallographic orientation of the substrate surface, the substrate temperature, and the nature of the diluent gas. The electrical charge behavior of Si-SiO2-A1 structures prepared under various conditions was investigated by capacitance-voltage (C-V) measurements of metal-insulator-semiconductor (MIS) capacitors. The experimental approaches and results are discussed in this paper. 1) DEPOSITION OF SILICA FILMS The overall reaction for the oxidation of silane is: The equilibrium constants of this reaction in the temperature range 500° to 1500°K, calculated from the JANAF thermochemical data,= are shown in Fig. 1. In addition to the large equilibrium constants, the oxidation of silane is also kinetically feasible at room temperature and above. However, the strong reactivity of silane toward oxygen tends to promote the nucleation of silica in the gas phase through homogeneous reactions, and the deposition of this silica on the substrate would yield nonadherent material. The formation of silica in the gas phase can be reduced by using low partial pressures of the reactants. Argon, hydrogen, and nitrogen were used as diluents in this work. 1.1) Experimental. The deposition of silica films by the oxidation of silane was carried out in a gas flow system using an apparatus shown schematically in Fig. 2. Appropriate flow meters and valves were used to control the flow of various reactants, i.e., argon, hydrogen, nitrogen, oxygen, and silane. Semiconductor-grade silane, argon of 99.999 pct minimum purity, oxygen of 99.95 pct minimum purity, and nitrogen of 99.997 pct minimum purity, all purchased from the Matheson Co., were used without further purification. In several instances, a silicon nitride film was deposited over the silica film. This was achieved by the nitridation of silane with ammonia using anhydrous ammonia of better than 99.99 pct purity supplied by the Matheson CO.' The reactant mixture of the desired composition was passed through a Millipore filter into a horizontal water-cooled fused silica tube of 55 mm

Jan 1, 1969

By H. J. Levinstein, H. J. Guggenheim, C. D. Capio

An optical incestigation of the phase transformations in RbFeF, has been conducted. Details of the ferromagwetic phase transition and the metamagnetic state are disczrssed. The three-dimensional magnetic domain structure existing in bulk crystals of RbFeF3 is described, as well as the effect of the magnitude and direction of the applied magnetic field on the domain struclure. The strong magnetoelastic interaction in RbFeF, is demonstrated. The results of the direct observation of the role of dislocation subboundaries and slip bands as nucleation sites and as pinning sites for magnetic domain walls are reported. THE perovskite compound RbFeF, has recently been shown to exhibit three magnetic states.''' Above 102°K it is paramagnetic, between 102" and 87°K it is antiferromagnetic. and below 87°K it is ferromagnetic (i.e., exhibiting remanence) with a modification of the magnetization occurring at 40°K. The changes in magnetic structure at 102o, 87°. and 40°K are accompanied by shear transformations to successively lower crystal symmetry classes.3 At 102°K a second-order phase transformation to a tetragonal crystal structure occurs. The c/o ratio increases with decreasing temperature to a value of 1.0034 at 87°K where the crystal undergoes another shear transformation to an ortho-rhombic crystal structure. The magnetic modification at 40 K is also accompanied by a shear transformation to a lower crystal symmetry. RbFeF3 is unique in that in the ferromagnetic state it is transparent in the bulk to visible light, has a low saturation magnetization, a large magnetic rotation. and has good optical properties.' All these features make it an ideal material for the investigation of magnetic domain structures in bulk crystals. In addition a dislocation etch has been developed which reveals the point of emergence of dislocations with the (100) surfaces of RbFeF3,5 making it possible to determine the dislocation arrays in the material. As a result domain wall dislocation interactions can be observed in the bulk crystal. In this paper we report on 1) the crystallography of the phase transformations in RbFeF3. 2) the domain configurations as a function of magnetic field and crystal orientation. 3) the interaction of dislocations and magnetic domain walls in RbFeF,. EXPERIMENTAL PROCEDURE Since the temperature range of interest is below room temperature the dewar shown in Fig. 1 was employed. It was designed to fit on the stage of a Leitz panphot metallograph, and permitted examination of the sample at a magnification up to 150 times. The dewar consists of a double-walled glass cylinder bent into an L shape. The space between the walls is evacuated. The viewing wirldows were made of four optically flat quartz discs aligned parallel to each other and sealed to the sides of the concentric cylinders. The specimens were mounted in a holder attached to a flexible plastic shaft. Various holder designs were employed depending upon the type of observations to be made. For studies of the phase transformation between the antiferromagnetic and ferromagnetic state the holder shown in Fig. 2(d) was employed. This holder permitted accurate temperature control at 82" to 88°K by balancing the heat input from the carbon resistance heater against the heat loss to a heat sink immersed in liquid N2. Magnetic field studies were conducted by employing the holders shown in Figs. 2(a) and (b). The holder shown in Fig. 2(n) has a solenoid imbedded in it. such that the magnetic field direction is in the same direction as the incident light. The magnetic field provided by the holder in Fig. 2(b) is perpendicular to the incident light direction. The holder in Fig. 2(r) was employed when observations of the specimen were desired while an elastic bending stress was applied to the sample. The stress was applied to the sample by pulling a wire from outside of the dewar. The wire was attached to a lever pivoted on the holder. which caused the knife edge of the lever to push against the sample. The crystal growth and the sample preparation were described previously.' PHASE TRANSFORMATIONS The first phase transformation in this system is from the cubic perovskite structure to n tetragonal

Jan 1, 1970

By E. S. Wheeler

THE rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the latter weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. FIG. 1.-A GROUP OF MONEL METAL AND NICKEL CASTINGS. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant. equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success.

Jan 1, 1930

By Hugh H. Waesche

High quality quartz crystals weighing more than 50 grams are required in several important industrial applications.30,31 Primarily, they are the basic raw material for precision, electronic, frequency control components; this includes oscillators and filters in both radio and telephone services. Quartz crystals are also necessary for optical lenses and prisms in special applications requiring high ultraviolet light-transmission as in spectrographs. Quartz wedges are regular components for petrographic microscopes. The application of crystalline quartz as a transducer* in ultrasonic devices has increased in recent years despite strong competition from barium titanate and magnetostrictive [f] devices. Some quartz is fabricated into delay lines for radar. Man has valued quartz for fabrication of art objects since the dawn of history. The art forms were and are painstakingly carved and polished to form intricate figurines, bowls, statuettes, and the well-known crystal balls. The largest known ball, made of perfect quartz from Burma, is now in the National Museum in Washington. It is 12 7/8 in. in diameter and weighs 106 lb 12 oz. Clear, pure quartz chips and small crystals not meeting the electronic-grade dimensional requirements are known by the Brazilian term lasca. They are used to produce fused quartz having wide application in laboratory equipment, as special glasses, for torsion suspension in scientific instruments, and as a source material for growing large artificial quartz crystals 18,35 Electronic applications far exceed all other uses in importance so any discussion of high-quality quartz crystals must be concerned almost exclusively with those functions. Historical Background Because of their ubiquitous character and natural beauty, quartz crystals have long been of interest and known to man. They have been found among early Egyptian and Chinese art forms and the Sumerians are believed to have fashioned seals, beads, and other jewelry from quartz crystals, perhaps 5,000 years ago. Also, American Indians made arrow heads and fashioned some simple objects of different kinds. The origin of the name quartz, although of Greek derivation, is uncertain. The Greeks appropriately applied their word for frozen water or ice, krustallos, to quartz. The present-day, large-scale practical applications of quartz crystals began in 1880-1881 when Pierre and Jacques Curie reported discovery of the "piezoelectric" effect. They found this effect first in Rochelle salt, a common product of grape-wine refineries, while studying crystal symmetry. Piezoelectricity is that property found in certain crystals, including quartz, whereby electrical charges of equal and opposite sign appear on opposite parts of the crystals when they are stressed. If equal and opposite forces are applied to two opposing prism edges of a single untwinned quartz crystal a positive electrical charge will appear on one edge and a negative charge on the other. The amount of the charges will be directly proportional to the force applied. This property seems to be intimately related to pyroelectricity

Jan 1, 1960

By Spencer S. Shannon

The lanthanide elements from lanthanum (atomic number 57) to lutetium (71) plus yttrium (39) are called the rare-earth elements; scandium (21) is chemically similar to yttrium and the lanthanides, but differs in occurrence. The rare-earth metals were divided into three categories by the chemist, Berzelius, in the early 1800s; however, modern usage defines only two groups. The cerium group is named after the most abundant -element and comprises lanthanum (57), cerium (58), praseodymium (59), neodymium (60), promethium (61), samarium (62), europium (63), and gadolinium (64). Traces of natural promethium were discovered in apatite in Finland (Erametsa, 1965). The yttrium group, also named after its most abundant representative, comprises terbium (65), dysprosium (66), holmium (67), erbium (68), thulium (69), ytterbium (70), and lutetium (71). Yttrium most closely resembles holmium in chemical properties, and occurs most commonly with the heavy lanthanides. The rare-earth minerals may be divided into cerium-group, yttrium-group, or mixed-group classes. A number of rare-earth minerals contain thorium and uranium, but these are variable in content and are not essential to the composition of the minerals. In monazite, a mineral that is a principal source of rare earths, the worldwide average content of thorium oxide is 7.2 % ; however, varieties of monazite contain as little as 0.001% and as much as 31.5% thoria. Monazite is the chief ore of thorium and, until recently, thorium has been the main product; the rare-earth metals were in fact byproducts. However, because of the great demand for rare-earth metals by the petroleum refining and the iron and steel industries since the early 1970s, the roles have been reversed so that thorium is now the byproduct. Uses A 9 to 1 mixture of yttrium and thorium oxides is used for high-intensity incandescent lamps and for high-temperature-resistant windows and lenses. Yttrium oxysulfide and orthovanadate, doped with europium oxide, are used in color television tube phosphors. Yttrium, as well as cerium, praseodymium, and samarium, is alloyed with cobalt to form strong permanent magnets. It hardens magnesium alloys and retards the oxidation of iron-chromium alloys. Yttrium-iron garnets are used for transmitting low microwave frequencies. Yttrium-aluminum garnets are used as host crystals for lasers and as artificial gems. Yttria also forms strong, stable, high-temperature refractories. Gadolinium-gallium garnets are used in substrate wafers on which bubble-memory films are deposited. Rare-earth chlorides, particularly of lanthanum, neodymium, and praseodymium, are used as catalysts for petroleum cracking. Mischmetal is used for lighter flints and to improve the ductility and impact strength of iron and steel alloys. Mischmetal also reduces the fatigue resistance of magnesium and aluminum alloys. Rare-earth oxides are used for polishing glasses and lenses. Individual or specific combinations of high-purity oxides are used as additives in glass to maintain or change its color, dispersion, or refractive index. High-purity oxide combinations are also used to color tile and to opacify porcelain enamel. Rare-earth fluorides and oxides are used in carbon-arc electrodes to provide incandescent white light. Lanthanum or gadolinium oxysulfide phosphors, activated with terbium, are used as x-ray screen intensifiers. Hydrogen can be stored by sorption on lanthanum-nickel alloys (Anon., 1979). Thorium232 is bombarded with slow neutrons in breeder reactors to create fissionable thorium233 for nuclear fuel cells. The 330-MW, high-temperature gas-cooled reactor at Fort St.

Jan 1, 1983

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By D. N. Dietz

A method for determining average reservoir pressure is presented, which is simpler to apply than that devised by Matthews. Brons and Hazebroek. For bounded reservoirs, identical results are obtained if stabilized-flow conditions prevail. The present method yields inferior results in the transient state. The method can, with a slight modification, also be used for water-drive reservoirs. INTRODUCTION In the method proposed by Matthews, Brons and Haze-broek' for determining average reservoir pressure in a multi-well reservoir, the cumulative production (the production time of each well) enters twice: once when the buildup is plotted against In (t + t)/At to arrive at p*, and a second time when the correction, p*-p is determined with one of the several formulas for differently shaped drainage areas. Once a steady state has been attained, however, the previous production history should be immaterial. The same pressure distribution could have been arrived at after different cumulative productions of the individual wells. In principle, therefore, it should be possible to determine average pressures without referring to cumulative productions. In the following paragraphs an expression is presented for the difference between the pressure in a producing well and the average pressure of its drainage area. Then the build-up time needed to overcome this difference is indicated. CASE OF A CIRCULAR DRAINAGE AREA AND A CENTRAL WELL PRESSURE DISTRIBUTION BEFORE SHUT-IN The general differential equation of radial flow (see Muskat, Eq. 10.2) may be written In the steady state, the rate of production of the well is equal to the rate of expansion of the fluid contained in the the drainage area; thus

Jan 1, 1966

By A. B. Parsons

NOT every organization on reaching the relatively ripe age of three score and fifteen can say with truth that its purpose and objects remain precisely the same as prescribed by its founding fathers. Of course, constancy of purpose may be something else than unalloyed virtue. It could merely reflect slavish worship of tradition, intellectual stagnation, or sheer inertia. On the other hand, it could establish the fact that the founders were men possessed of broad outlook, of prophetic vision, and of an acute sense of direction. In addition to charting the course with precision, the founders of the A.I.M.E. surely showed a flair for expressing clearly in a few words what others might say obscurely in many words. To quote verbatim from the "call" for the meeting, in 1871, the proposed organization was to have: "two great objectives: "First, the more economical production of the useful minerals and metals. "Second, the greater safety and welfare of those employed in these industries." This text underwent some refining on several subsequent occasions but today the ultimate product, as set forth in the Constitution reads: "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means." The original call was dated "Wilkes-Barre, Pa., April, 1871," and was signed by Eckley B. Coxe, of Jeddo, and by R. P. Rothwell and Martin Coryell, both of Wilkes-Barre, each of the three subscribing himself as "mining engineer." The authors proceeded to explain briefly just how it was proposed to achieve these objectives: "In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed, as the free interchange of experience among those actually engaged in these industries; and this object has been accomplished mainly through the medium of `Institutes,' `Associations,' or `Societies,' composed of those engaged in these occupations, and by the periodical publication of `essays' or `papers' communicated to such societies by their members. "It must be evident to all practical men that the interchange of the varied experience

Jan 1, 1947

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

AMONG the features that make Inspiration of outstanding A interest, particularly to the engineer, is the fact that at various times it has used, as a major method of production, three more or less distinct methods of mining and three distinct methods of treating its ores. The following chronology is of interest : Major Mining Methods: 1915-194 7 Underground block-caving, exclusively 1948-1952 Underground block-caving and opencut mining 1953-1954 Underground block-caving, opencut mining, and "glory-hole caved-block transfer" mining 1955 on Opencut mining and "glory-hole caved-block transfer" mining. Major Ore Treatment Methods: 1915-1925 Flotation concentration exclusively 1926-1930 Flotation concentration and ferric sulphate leaching 1931-1955 Ferric sulphate leaching (the so-called "Dual Process" was used for eleven months in 1937 when demand for copper was phenomenal; and the "leach-float" process was used for 24 months in 1942-44 as an expedient to help meet war demands for copper). 1956 on "Dual Process" combining a sulphuric acid leach followed by fine grinding and flotation of the residue from the leaching vats.

Jan 1, 1957

By S. T. Yuster

An analysis has been made of the factors responsible for tilted fluid contacts in petroleum reservoirs. The factors are static and dynamic with the former being controlled by those variables responsible for the capillary rise of fluids, and the latter include rate of formation tilt and hydraulic circulation. The explanation that rate of formation tilt may be responsible for tilted contacts appears untenable. The role of some of these factors in the migration, fractionation. accumulation and possibly the prospecting for oil is indicated. INTRODUCTION While it is generally considered that the segregation of gas, oil, and water in a petroleum reservoir results in approximately horizontal planes separating these phases. there are factor; which modify this simplified picture to a very great extent. Some of these factors are static. and the departure of the fluid interfaces from horizontal may represent a static equlibriun. Some of these factors may be dynamic and the interface positions may be non-equilibrium and represent a steady .state condition. Of course combinations of these two situations may also exist. The reasons most commonly given for this behavior are hydraulic circulation of fluids, change in character of the formation, and a rate of tilt of the formations more rapid than the rate at which the fluids may re-establish an equilibrium. Russell's Principles of Petroleum Geology' contains an extensive discussion of tilted fluid interfaces and their importance in the migration and accumulation of petroleum. Russell cites examples of tilted water tables at Lance Creek, Wyo.; Rock River, Wyo.: Cut Bank. Mont.; Cushing, Okla.: and Graham; Okla. Also given was the Wasson Field of West Texas which has saucer shaped oil-water and gas-oil interfaces with the saucer being deeper in the case of the oil-water contact. The Bradford Field in Pennsylvania has a tilted water table. San Ardo. Coalinga None and some other California field.; have tilled contacts. A recent paper by King Hubbert discuses the effect of hydraulic circulation of the water underlying the oil in a given stratun and it- implications in the accumulation of and drilling for the oil. The foregoing would indicate that tilted fluid interfaces are not uncommon and that it would be of importance to underbtand the forces which are responsible. Further. it would be of interest to examine certain idealized models of situations which may cause tilting with the thought in mind of deriving relatinnships between the important variables. These relationships may only hold exactly for the model* assumed but the results may apply semi-quantitatively to actual formations and at least indicate trends. The discussion will be divided into the effect of static factors and the effect of dynamic factors. STATIC FACTORS It has already been mentioned that one reason given for tilted contacts is a variation in formation properties. Specifically this is a change in the pore size of the formation capilaries. If the internal surface of the reservoir is preferetially wet by water, capillarity will cause the water 10 rise to a greater extent above the free water table in a small capillary than in a large one. Consequently the water-oil contact will be higher in the lower permeability sands than in the higher permeability sand.;. The free water table may be defined as the position the oil-water interface would take if capillarity were absent. Since the phenomenon is the capillary rise of water in an oil environment, a derivation of this shold give a relationship between the variables. Fig. 1 is an idealized model of the situation with a uniform bore circular capillary ubstitttting for the tortuous non.circular formation pore. The upward force.; on the column of water will be equated to the forces downward to give the equilibrium situation. forces upward = force downward where r is the radius of the capillary in ceritimetera. a is the interfacial ten4on oil-water in dynes per centimeter, 0 is the

Jan 1, 1953

By Carl Gatlin, S. Srini-Vasan

It is shown thar k k ratios cornputed on the as.sutnption that the average sandstone reservoir has a pore-size distribution characrerized by a linear 1/P saturatioN plo are in good agreewient with correspotlding k,,/k,, ratios obfairzed by Wahl, Mul-/ins and Elfrink by correlatiotz of field measurements. Methods of calculating relative permeability data have recently been reviewed and extended.' It was shown that for sandstone reservoirs where ' is approximately a linear function of effective saturation (as suggested first by Corey') it is possible to express relative permeabilities in very simple terms. For systems wetted by connate water and producing oil and gas (gas saturation growing at the expense of oil) the expression for the The accuracy of Eq. I has been frequently confirmed in our laboratories; because of its simplicity we make routine use of it in the analytical solution of proble~ns in reservoir engineering. Nevertheless, comparisons of the k,,,/k,, ratios yielded by Eq. 1 with appropriate reservoir data have been few. The publica- tion by Wahl, Mullins and ElfrinkV of an empirical equation for k,,/k,, ratios is thus of interest since this equation is specificalljl stated to be Vased on the correlation of field measurements made on sandstone reservoirs. Not surprisingly these authors found that it was necessary to

By D. A. Summers, C. J. Haas, G. B. Clark, J. W. Brown

While significant advances have been made in excavation of rock, largely in improvements in drilling, blasting, loading, and haulage, conventional operations have been improved until little feasible increase in efficiency or rate of advance appears possible. Tunnel-boring machines have been developed which will excavate at rapid rates in soft to medium- hard rock. Hypervelocity impact is being intensively investigated as a possible means of cutting and breaking rock, as well as lasers, electric current, explosive drilling, high frequency vibration, etc. The current development and use of high-velocity small-diameter water jets, metallic jets, and projectiles of various materials involve ultra-high-pressure phenomena of fundamental interest. Rock disintegration by water jets has been investigated in the USSR for over a decade. Large-diameter jets of low velocity are used to mine coal, and high-velocity capillary jets will cut and break rocks under laboratory conditions. Velocity ranges for breaking and cutting are dependent upon rock and jet properties, and pulsed jets break some rocks more easily than continuous jets. Spectacular laboratory results have been reported for breakage of unconfined blocks of some types of rocks. Compressors, pressure multipliers, gas explosion chambers, and water cannons have been used to generate jets. Jet properties, such as continuity, unit pressure, total pressure, and stability have been measured. Results agree with theory, although the latter has been established only for relatively low-velocity flow. Diameter, speed of traversing, and frequency of pulsed jets affect rock response. Investigations in Britain have only recently begun consideration of harder rocks and higher velocities, although water jet cores have been found to be more continuous at lower velocities than previously believed. Lower limits of jet velocity for rock cutting were established for the rocks investigated.

Jan 1, 1970

By D. L. Albright, G. A. Colligan

An investigation has been conducted to determine the nature of the crystallographic substructure of nickel and a 1.0 wt pct Ag-Ni alloy which had been undercooled 105°C prior to solidification. A rotating back-reflection X-ray technique and modified Weissmann diffractometer were used to orient single-crystal sections from these poly-crystalline ingots and to determine the substruc-tural features of these single crystals, The sub-grain size in the pure nickel ingot is 0.5 mm diam while the silver-doped nickel subgrain size is only 0.1 mm diam. The misorientation between adjacent subgrains is approximately 1 deg of arc in both ingots, and the spread of orientation of sub-grains about the mean orientation of the crystal is 5 deg of arc in both ingots. The addition of silver results in a stable impurity substructure which is preserved during isothermal solidification and subsequent cooling to room temperature. In the absence of silver the initial impurity substructure is destroyed by dislocation interactions which produce a secondary substructure which grows to a size five times larger than the initial substructure. THE process of undercooling a metal entails cooling of the molten sample below the equilibrium freezing point without the occurrence of solidification, i.e., by exercising proper constraint over the experimental variables contributing to nucleation in the melt. The current work of walker1 and Colligan Metal reports undercooling large continuous samples of nickel by imposing appropriate restrictions upon the parameters of solidification. The silver-nickel equilibrium diagram3 reveals the presence of a monotectic reaction at 1435°C. At this temperature the maximum solid solubility of silver in nickel is approximately 3 wt pct, but this solubility decreases with decreasing temperature and the solute is rejected as a silver-rich liquid phase at temperatures below 1435°C. Thus, the 1.0 wt pct solute should be held in solution during undercooling and solidification and subsequently precipitate as a silver-rich liquid phase at grain and subgrain boundaries following solidification during cooling below 1435. This assumes no solute segregation sufficient to cause the monotectic reaction. One would expect this second phase to inhibit grain and subgrain growth by retarding dislocation motion after solidification is complete. The effectiveness of silver addition in growth retardation of high-angle grain boundaries has been demonstrated by Colligan and suprenantS4 The principal [l00] dendrite growth directions in a 2 wt pct Ag-Ni alloy undercooled 53 all radiated from the nucleation site. A similar pure nickel ingot undercooled 59°C exhibited a random orientation of [l00] dendrite directions with respect to the nucleation site. Since undoped nickel ingots do not retain any evidence of the casting or solidification texture and silver-doped ingots do retain this texture, it is reasonable to assume that considerable grain growth has taken place in the pure nickel. These particular experiments were performed in order to reveal the differences, if any, in the features of the crystallographic substructure of undoped undercooled nickel and silver-doped undercooled nickel. 1) EXPERIMENTAL PROCEDURE Data are reported on selected specimens from two massive (approximately 260 g) undercooled ingots of nickel. One ingot consisted of electrolytic nickel and the other of this same material with 1.0 wt pct addition of high-purity silver. Powder patterns were taken of both the as-received and as-solidified materials; in all cases the reflections recorded were attributable to the individual elements nickel and/or silver. Fig. 1 is a. schematic diagram of the apparatus employed for the undercooling experiments. The equipment consists in part of a fused silica crucible for containing the charge. A fused silica tube encloses the system, which is covered by a brass cap to permit partial sealing of the inert atmosphere. This cap contains a hole through which a Pt-Pt 13 pct Rh thermocouple is inserted for temperature measurement. The charge is inductively heated under a purified argon atmosphere.

Jan 1, 1963

By G. S. Cole, G. F. Bolling

Fluid flow strongly influences ingl structure and the columnar -to-equaaxed transition. Artificial flow patterns siwzilar to the nuturul ones act to induce this transition, while dampening forces act to suppress this transition. It is shown here how simple mechanical forces can be applied to a systerrz in order to induce or slipPvess relative fluid flow and the change both the structure transition and the exact structures obtained. The example used is the effect of slow rotations and oscillations 012 a cooling- ingot (of laboratory scale). The details of rotution and oscillation for various cooling rates, lenlperal~ire gradients, and sizes of ingot are related to other solidzfication variables. THE grain structure of a casting can be changed by altering the fluid motion during solidification. Just how important these changes are depends directly upon the degree to which the fluid motion can be controlled. An early step in understanding the nature and influences of fluid motion was taken by studying natural thermal convection; when a static mechanical device was used to suppress natural flow the result was opposite to that obtained when an electromagnetic device was used to augnlent flow in a pattern similar to the natural one. ''2 Suppression allowed more columnar growth to occur, but "augmented natural convection" brought about an earlier columnar-to-equiaxed transition (CET). Since the solidification of a free ingot must have characteristics somewhere between those displayed during suppression and augmentation, we know that natural convection must influence the CET. Further, since heat transfer in the liquid is always some time-dependent combination of convection and conduction, it can easily be guessed that the temperature gradient in the liquid is the vital factor affecting the CET.1,2 It is obvious that the structure arising from the unadulterated solidification of an ingot, without external influence, is rarely if ever the best possible one. Although the pattern of the natural fluid flow may be considered efficient, the magnitude of the flow and the heat transfer decrease freely from the outset. For a

Jan 1, 1968

By J. Chipman, N. J. Grant, R. Rocca

Desulphurization of liquid iron by reducing slags of the electric-furnace type was studied from 65 heats. Variations were made in basicity over a wide range and in FeO up to about 5 pct for their effects on desulphurization. The role of FeO in desulphurization from the blast furnace, to the electric furnace, to the oxidizing conditions of the open hearth is shown to fit a relatively simple pattern of behavior. THE mechanism which controls the desulphurization of molten iron by basic slags has been the object of several investigations. In particular, equilibrium determinations have been made both in the field of basic open-hearth slags, which have a high iron-oxide concentration, and in the field of blast-furnace slags which have a very low iron-oxide concentration. In both cases the desulphurization ratio has been found to increase with increasing basicity of the slags; however, the mechanism of desulphurization differs in the two cases. In basic open-hearth slags desulphurization occurs mainly as a partition of iron sulphide:&apos; FeS * (FeS) and the desulphurization ratio is approximately independent of iron-oxide concentration in the slag. In blast-furnace slags the concentration of iron oxide is very low as a result of the highly reducing conditions in which they are formed. The controlling reaction for desulphurization is then:2,3 FeS + (CaO) <=* (CaS) + (FeO) The slags of the reducing stage in the electric furnace have an iron-oxide concentration which is intermediate between blast-furnace and open-hearth slags. The study of the mechanism of desulphurization for these slags has been the object of this investigation. The importance of low (FeO) in the slag for desulphurization was first verified by Bardenheuer and Geller,& who found that high desulphurization ratios were obtained in highly reduced slags. It was recognized" hat iron oxide in the slag becomes a controlling factor in desulphurization only at FeO concentrations approximately under 5 pct. A recent investigation conducted by Buehl,7 upon the suggestion of one of the authors, confirmed this opinion from the results obtained from a heat conducted in a small arc furnace. In the present investigation, slags of very high basicity, such as often are encountered in the basic electric furnace, could not be studied, but equilibrium data have been obtained for slags in a wide basicity range. The iron-oxide concentration in these slags ranged from 0.08 to 15 pct and was controlled by the addition of silicon to the metal. Other constituents of the slags were mainly CaO, MgO, SiO2, A120,, and CaF,. The experimental technique was essentially the same as that of previous investigations.1 8-lo In an open magnesia-lined induction furnace, 65 lb of Armco ingot iron was melted. An atmosphere of hydrogen was maintained over the melt for 1 hr to bring the carbon content down to approximately 0.010 pct maximum. The bath then was exposed to air for 25 min to remove hydrogen. The electrodes were put in place, and the furnace was operated from this point on in an atmosphere of nitrogen. A synthetic slag was added to which additions of silicon and iron sulphide were made. A rate study conducted at the beginning of this investigation had

Jan 1, 1952

By W. E. Foreman, James A. Redding

INTRODUCTION Screening is a mechanical process that separates particles by size. Modern coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modern preparation plants is done for the following reasons: 1 ) Removal of fine coal before a size reduction step. 2) Size separation of the coal into a coarse and fine fraction for sized products or processing in coarse and fine coal circuits. 3) Recovery of heavy media from heavy media coal cleaning circuits. 4) Dewatering. 5) Rock and trash removal by handpicking on a screen. Fig. 8-1 is a generalized flowsheet of a plant showing the use of screens in the coal preparation process. Table 8-1 shows the vibrating screen equipment utilized in Fig. 8-1

Jan 1, 1979