Search Documents

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948

By R. H. Edsal, G. Horvay

The transient one-dimensional heat-conduction equation is solved for two semi-infinite media, at different initial temperatures, brought into (poor) thermal contact. It is shown that the two interface temperatures gradually approach the well-known, instantaneously assumed, common interface temperature of the case of zero contact resistance. The present analysis, with slight modifications, may be used in fair approximation also for the class of problems involving a change of phase. One particular application of the boundary value problem solved in this paper concerns the determination of the temerature distribution in metal castings and molds.P This problem has been treated extensively by analytical methods (see e.g., the literature listed in Refs. 1 to 4) by electrical analogs (see e.g., Refs. 11 to 14) and also by experimental methods (see the literature listed in Refs. 4, 5), but prior to the work of Pellini and Ruddle the experimental results were rather unreliable. Immediate motivation for the work described in this paper was to better understand the results of Pellini,' which are typified by the curves of Fig. 1. Pellini cast 20-in. high, 7-in. sq steel ingots into cast-iron molds of various thicknesses. He measured the temperatures at mid-height, at a number of stations in the casting and the mold, and obtained the cooling curves shown in Fig. 1. The most conspicuous thing about Fig. 1 is the large temperature discontinuity at the interface between casting and mold, due presumably to the shrinking away of the casting from the wall and the attendant creation of an airgap, as the casting cools. Such a contact resistance slows down the anticipated freezing rate; an analytical prediction of this is of much interest in foundry practice. The determination of the effect of contact resistance in the presence of a change of phase will be dealt with, by an approximate method, in a separate paper.' In the present paper the much simpler problem is considered in which there is contact resistance but no change of phase. This problem frequently arises in the analysis of aircraft structures.+ It can initial temperature, and may be regarded as semi-infinite. We suppose the thermal properties in the two media to be time, temperature, and space independent; there are no sources or sinks within the media. In Fig. 2(a) we illustrate, schematically, the case of no contact resistance. The semi-infinite media "0" and "2:' initially at temperatures 8 (- m) and 8(+ -), respectively, are brought into contact at time t =0. A common interface temperature 8,i = is instantaneously established, and thereafter remains constant. Temperature curves are drawn for three instants of time. When there is contact resistance between the two media, the temperature equalization occurs as sketched in Fig. 2(b). Fig. 2(c) illustrates a temperature curve, using the dimension-less notation Barber-Weiner-Boley6 have stated the equations [23a, b] given below, which govern the heat transfer in the two media, and solved them for a rather complicated special case. In their example both media "O" and "2" are finite, are insulated at their far ends, and there is steady heat input into medium 2. In Eq. [27] we give the general solution of the most important special case, where the two media are semi-infinite and there are no sources or sinks. In this case the results may be stated in simple closed form. In Fig. 3, to be discussed in the next section, we illustrate the variation of the interface temperature when steel at 2760" is brought into contact with iron at 100". This example, if we disregard the effect of the heat of fusion, is comparable to Pellini's experimental results, Fig. 1. (Unfortunately, however, experimental determination of the interface temperatures was difficult to carry out, and hence Fig. 1 is not very accurate near the interface.) In Figs. 4 and 5 of the following section, we similarly compare Pellini's sandcasting tests with analytical results for the case where steel at 2760" is brought into contact with sand at 100". It will be pointed out that, insofar as the interface temperatures are concerned, heat of fusion has a minor effect, and so the present approximation, with small modifications, may be

Jan 1, 1961

By Yang Tsang Woo

I will endeavor to describe the methods of silver-mining and smelting employed by the natives in Mongolia. Modern methods have been applied there, but with little success; and, since they are familiar to most members of the Institute, I will simply mention that the failure was due to the high price of coke used in smelting the ore in modern furnaces, and to the unsuitable mill-machinery employed for concentrating the galena, which is finely distributed in the ore. The Jehol silver-mines are situated about 45 miles NE. of Jehol, the capital of Mongolia. They embrace two mines, 5 miles apart,—the Ku Shan Tze mine and the Yen Tung Shan mine. They were first worked by natives 50 years ago, about the time when mining was so flourishing in other parts of the world,—for instance, in California and Australia. The upper part of the vein is galena mixed with iron-stone, and is 2 to 4 ft. thick. At lower levels the vein is composed of silver-lead ore running between quartz-porphyry walls. Limestone, talc and black shale, colored by graphite, are found in other parts of the mine. Crystalline limestone is found 1 mile NE. of Ku Shan Tze. Granite is encountered in the Yen Tung Shan mine. Mining.—The native method of working the mines is most primitive. The same method may have been employed a thousand years ago. A small inclined shaft, 4 ft. by 4 ft., is sunk in the vein-stuff where the appearances are most favorable. Another shaft is sunk 20 or 30 yds. away, for ventilation. The shaft follows the vein in a zigzag fashion in whatever direction the vein appears to be richest. Timber is used only in soft ground. Where the ground is hard, the roof is cut into an arch-form. In some places, instead of using ladders, steps are cut in the rock, just wide enough to hold one foot. The deepest native workings are 400 ft. below the

Jan 1, 1903

I HAVE previously shown you in the Fifth Book the process of making guns and gun carriages, together with other preparations and methods of moving them. If I now failed to show you more about them, it would be as if I had pointed out only the useless shadow of a thing, for I did not show the kinds and arrangement of their supplies or how the effects for which they are made are achieved. For these reasons I now wish to tell you, in addition to what I have already said, how saltpeter is made and the methods of refining it well; what it is and how without it guns and many effects of violent and artificial fires would have been discovered in vain. After this, I also wish to tell you the methods of compounding the powders for large and small guns, and finally how these are loaded and discharged. I also wish to tell you how mines are made, and fire tubes, [149v] fire pots, squibs, fireballs, rockets, shells, grapeshot, and other similar devices for shooting fire in order to bum ships, supplies, bridges, and ramparts, or, in offense, for firing on batteries. I also wish to teach you to make certain bronze balls for shooting, which carry fire and break in many pieces when they hit. For surely, besides being terrifying to the sight, they would be harmful to armies lined up in battle when they are fighting. Likewise, I wish, to enlighten you as to how artificial fires are made that last long and are difficult to extinguish. Since these are fine and useful things in wars, every captain and soldier should give them consideration and know how to use them when necessary. You will be pleased to have this information if for no other reason than that you can teach it to those who take delight in celebrating holidays with festivities and with fires.

Jan 1, 1942

By M. W. Burkart, B. Lustman

Uranium-base alloys exposed to high temperature water fail either by uniform oxidation or by sudden cracking and disintegration of the metal. The disintegration results from the oxidation of a second phase which is precipitated during the corrosion process. The precipitate has been identified as a metastable hydride of uranium. URANIUM-BASE alloys consisting of the body-centered-cubic ? phase are susceptible to two different modes of corrosion failure when exposed to high temperature water. In the first process, a smooth oxide film is formed on the metal surface which continually flakes off during exposure and results in a uniform weight loss of the specimen. The oxide is present as a thin, adherent layer whose thickness remains approximately constant. As the metal oxidizes during corrosion, a nonadherent layer is built up on this film and continually sloughs off. Coincident with the uniform corrosion just mentioned, another process occurs which eventually leads to failure of the metal by cracking and general disintegration. The failure takes place during a relatively short time compared to the total exposure. To distinguish this type of failure from the uniform corrosion, the cracking or disintegration of the metal will be referred to as discontinuous failure. For the ? phase uranium alloys it is discontinuous failure rather than uniform corrosion that limits the useful corrosion life of the alloy. This paper will be concerned primarily with the mechanism of discontinuous failure. Physical Changes During Corrosion—The alloys used in this investigation were ? phase uranium alloys containing 7 to 12 wt pet Mo or Cb. The preparation of the alloys, the method of corrosion testing, and the actual corrosion results are presented in another paper.' The ? quenching treatment consists of annealing the alloy for 24 hr at 900°C in a sealed Vycor glass tube filled with helium and then water quenching to room temperature without breaking the tube. The corrosion behavior typical of a ? phase uranium alloy is shown in Fig. 1. This specimen was a U-12 wt pet Mo alloy tested in pressurized, degassed water at 650°F. The corrosion rate was practically constant at 0.28 mg per sq cm per hr or increased slightly until about 15 to 20 days of exposure, when the onset of discontinuous failure occurred in this particular sample, and the specimen soon began to crack and disintegrate. The simultaneous increase in the observed corrosion rate is a result of the increased area of exposure due to cracking of the specimen. The microstructure of a specimen that failed by cracking is shown in Fig. 2. The presence of a plate-like precipitate can readily be seen. Metallographic examination of corrosion specimens reveals that the onset of discontinuous failure is always preceded by the formation of a plate-like second phase in the ? uranium matrix. Hydrogen analyses of specimens periodically withdrawn from corrosion test reveal that the hydrogen content of the alloy increases on exposure to the high temperature water, as shown in Fig. 3. The hydrogen is available as a corrosion product resulting from the formation of UO2 by the reaction of the alloy with water. Specimens analyzed just prior to discontinuous failure contained as much as 1200 ppm H, whereas the plate-like phase appears to precipitate out at a hydrogen concentration of between 10 and 25 ppm. The observed increase in hydrogen content prior to and during the formation of the plate-like precipitate suggests that this constituent may be a hydride of uranium. Additional evidence linking the identity of this phase to a hydride is that it can be removed by vacuum annealing at temperatures of 100°C and above. Decomposition products of the ? phase would certainly not dissolve at such temperatures, nor could other likely products of corrosion, such as oxides, be dissipated at any of the test temperatures. The precipitation and growth of the second phase during corrosion is accompanied by an increase in hardness of the specimen. The hardness increase results from the dispersion of the harder precipitated

Jan 1, 1959

By J. W. Richards

There are two essentially different 'types of case-hardening processes; that using a dry mixture in which the object to be case-hardened is packed and kept for the necessary time at the necessary temperature, and the "liquid" proccss, employing a bath of fused salts into which the object is immersed and which by immediate contact case-hardens the surface of the article. The Shimer process belongs to the second class, and was a war emergency invention. Of the liquid melts used as baths, the most effective and most frequently used are melted potassium cyanide and melted sodium cyanide. These may be used either pure or mixed with salts that reduce the melting point and the percentage of .cyanide present. The use of these baths since 1914 has met many commercial difficulties because of the high price and frequent commercial scarcity of the cyanide salts; at present sodium cyanide has practically entirely displaced potassium cyanide. Another trouble is the danger to the workmen handling the cyanide salts, which are extremely poisonous, and the annoying and poisonous vapors or gases given off in the workshop, unless an effective system of hoods and ventilation is provided, so as to prevent the gases from the baths mixing with the air of the room. Porter W. Shimer, of Easton, Pa., has invented a substitute1 for the bath of melted cyanides which case-hardens with equal or greater facility and effectiveness, gives off no poisonous vapors, and costs for chemicals materially less than the cyanide costs in the previously used baths. The process has been in use over a year in a large American works and the following statement embodies the results of practical experience in the use and operation of the process. The Shimer liquid or melted bath consists of a mixture of easily fusible salts that do not possess case-hardening properties, into which is immersed fresh calcium eyanamid, which imparts to the bath case-hardening properties. The composition of the non-case-hardening salts appears rather immaterial. Good results have been obtained by using a mixture of sodium chloride, calcium chloride, and barium chloride in equal proportions by weight; also a mixture of one part sodium chloride

Jan 1, 1920

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel's paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel's attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,', y uranium, and perhaps zirconim.' The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors' reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato's value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,'' and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener's predictions.28 We have no quarrel with Hagel's placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963

By E. J. Ripling

A NY mechanism proposed to explain hydrogen embrittlement in titanium and its alloys must, of course, be consistent with the experimental data that characterize this embrittlement. Unfortunately, however, the mechanical behavior of hydrogen-bearing titanium, at least a-ß titanium, has not been unequivocally defined. Lenning, Craighead, and Jaffee have clearly shown that hydrogen cmbrittles a-titanium by elevating its transition temperature, probably as the result of the formation of titanium hydrides. Therefore, in these alloys, hydrogen acts like at least one other interstitial contaminant, namely, nitrogen.&apos; On the other hand, ß-titanium has been shown by these same investigators to tolerate very large amounts of hydrogen without suffering severe mechanical damage.2 Mixing these two phases, however, to form the most important class of commercial alloys, the a-ß alloys, again results in severe hydrogen embrittlement, although the mechanism by which the embrittlement is produced is not of the same type as that which causes brittleness in a alloys. Ductility damage due to hydrogen increases as the strain rate is reduced in a-ß alloys, while embrittlement in a alloys increases as the strain rate is increased, since the latter is a transition temperature behavior. Steel, like the a-ß alloys, becomes more hydrogen sensitive at slow strain rates, suggesting that the mechanism producing the embrittlement in these two metals is similar. Brown and Baldwin&apos; described the hydrogen-produced ductility depression in steel as a function of testing temperature and strain rate by defining the slope of the two surfaces that produced the depression in a three dimensional chart, Fig. 1. One of these surfaces was given by the equations (de/de)4 > 0 (de/dT) < 0 [1] while the other was defined by the pair of equations Surfaces of the type given by Eq. 1 are suggested in two ways. One is an embrittlement mechanism wherein the diffusion rate of hydrogen is competitive with the rate at which the material is being deformed, as suggested by the planar pressure theory of Zapffe and his co-workers.&apos; The other is the diffusion controlled extension of Orowan&apos;s theory on delayed fracture in glass by Petch and Stables.&apos;&apos; Surfaces of the type given by Eq. 2 are also compatible with a mechanism of pressure build up in voids, according to de Kazinczy,&apos; since the solubility of hydrogen in the metal increases with testing temperature so that as the temperature is raised, the pressure in the voids is reduced. Kotfila and Erbin recently presented some data on the dependence of ductility on testing temperature and strain rate for the a-ß 3 pet Mn complex alloy at four different hydrogen levels.H Although data were presented for only three testing temperatures at three different strain rates, their results indicated that surfaces of the types defined in Eqs. 1 and 2 are produced in the alloy when the hydrogen level is sufficiently high—200 and 300 ppm—Fig. 2. Jaffee and his co-workers presented data on a number of different a-ß alloys which indicated the existence of surfaces of the type described by Eq. 2, but the ductility recovery at low temperatures as given by Eq. 1 was not found." In an attempt to aid in crystallizing this description of the ductility dependence of hydrogen-bearing a-ß alloys, tests were conducted by the author on a-ß titanium 140A with three different hydrogen contents. The tensile properties of two as-received rods and one vacuum annealed rod* were obtained over a range of testing temperatures and strain rates as shown in Figs. 3 and 4. Hydrogen analyses were made by the Battelle Memorial Institute on four pieces of the rod whose properties are shown as solid circles in Fig. 4. The hydrogen content of these pieces, taken at widely spaced intervals within the rod, were 280, 270, 289, and 270 ppm, indicating that the hydrogen content within a single as-received rod was quite uniform. One of the broken test pieces whose properties are shown in Fig. 3 as solid circles was also analyzed, and found to have a hydrogen content of 310 ppm. The analyses obtained on two of the vacuum annealed specimens were 92 and 170 ppm.

Jan 1, 1957

By Y. C. Liu

THE existence of mechanical twins in bcc metals has long been known. With recent intensive interest in the mechanism of twin formation and its role in plasticity and crack initiation, a study of the general Characteristics of twin intersection appears pertinent. The scope of the present note will be limited to the crystallography of the twin intersections of (112) twins, without consideration of its mechanism, movement of atoms, crystal structure, or the strain energy involved at such an intersection. The twinning elements of (112) twins are considered to be K1 = {112}, n1 = (111) and K2 = {112}, n2 = (111) with a twin shear of 0.707. The crystallographic features of twin intersections have been worked out in detail by Cahn.1 The present work applies the general principles postulated by Cahn to the intersections of (112) twins. The basic conditions for the twin intersection are: 1) The trace of crossing (A) and the secondary (C) twins in the planes of the crossed twin (B) must be parallel. 2) The direction (n1) and magnitude (s) of shear must be identical in the crossing and secondary twins. Also the sense of shear must be the same. These two conditions have to be fulfilled in order to maintain geometrical continuity at the twin interfaces. Fig. 1 shows the perspective representation of how these two conditions are fulfilled at the intersection. This type of intersection will be named Type-I. It is the purpose of this note to point out the existence of another type of intersection, Type-II, as shown in Fig. 2. In this type of intersection, the crossing twin A remains straight and the crossed twin B has been bent. The two conditions laid down by Cahn must also be met. This leads to the following corollary conditions: 1) The interface between twins B and C must be parallel to the twin habit of crossing twin A. 2) n1c must be parallel to n1A. 3) The twin shear (s) of twin C must be exactly equal to and in the same sense as that of crossing twin A. Thus, in order for the Type-II intersection to take place, the twining elements of secondary twin C must fulfill the above three conditions with respect to crossing twin A. Let K1 of crossed twin B be (112). All indices of the matrix can therefore be converted into new in-

Jan 1, 1963

By William P. Mason

FoR reasons unnecessary to enter into here, I was called upon to contradict the statement that " closed metallic vessels, partly filled with water and heated, do not become shattered by violent explosion, but simply rupture by over-pressure;" and the following experimental results were obtained in support of my position : A piece of drawn brass tubing (telescope-tubing) 1 1/2 inches in diameter and 15 inches long was closed at both ends by screwing on heavy caps of bronze. Before closing the second end the vessel was half filled with river water, the cap was then screwed on, and the closed vessel was supported upon two iron anvils, and heated in the interval between the supports by a large Bunsen lamp. The resulting explosion (which was doe to over-pressure only and not to any more occult cause) was exceedingly violent. No small damage was done to the room in which the experiment was undertaken; and the noise was like that of a cannon. Those of the pieces which could be recovered are shown in Fig. 1. Upon examining the wreck, it was noticed that one of the heavy bronze end-caps had preserved its circular section and still contained that portion of the barrel of the tube which had been screwed into it, while the other end-cap contained no portion of the tube, and was moreover sprung into a shape more or less elliptical, as if from excessive lateral strain. It was also observed that the large pieces of the shattered boiler predominated towards the end which had been closed by the un-sprung end-cap. The reasonable explanation, in view of the facts, was, that over-pressure had caused the boiler to yield through the screw-threads at A B, Fig. 2, and the righthand end-cap had blown off, thus leaving the boiler half filled with water, greatly super-heated for the new (atmospheric) pressure to which it was suddenly reduced; that this water had consequently sprung instantly into steam with dynamite effect, shattering the tube and springing the remaining end-cap. The large pieces would be expected at the open end of the boiler, as at that point the "tamping "would have been that of the atmosphere only. This explanation assumes a rupture to have been caused by gradually increased pres-

Jan 1, 1893

By Hewitt Wilson

CHALK is soft, pulverulent limestone formed from calcareous remains of microscopic organisms. Whiting is the powder made by the fine- grinding of limestone. Although European chalk dominated the early American market and is still shipped to the eastern and western seaboards, the domestic producer, by new technical processing, improved equipment, and proper selection and mixing of raw materials has shown that the United States can be independent of foreign sources. DISTRIBUTION European Chalk-Outcrops of Cretaceous chalk are found in the area roughly bounded by Antrim, Ireland, on the east, East Prussia on the west, Sweden and Scotland on the north, and Nice, France, on the south. Commercial chalk is mined from the chalk cliffs between Dover and Hull, England; from deposits near Mons, in the Departments of Pas de Calais and Nord in northern France; and from similar de- posits in Denmark and Belgium. United States-Some grade of limestone is found in every state of the Union, but true chalk of Cretaceous age is limited to three large areas in the central and southern states. Niobrara (Cretaceous) chalk outcrops are found as a narrow band encircling the Black Hills in South Dakota, Wyoming, and Nebraska, and in much larger exposures in southeastern South Dakota, eastern Nebraska, and western Kansas. A third chalk belt extends from west central Arkansas into Oklahoma and connects with the Austin beds, which almost cross Texas. In the southeastern states, the Selma chalk extends from western Tennessee south through northern Mississippi and turns east across central Alabama. Most of the domestic chalks are discolored with iron oxide or carbon. Some marls can be included with chalks of commercial possibilities. Some of the soft, cream-colored limestones of northern Florida, Georgia,

Jan 1, 1949

By J. P. Dovel

HAVING been requested to prepare a paper referring especially to my patents as applied to blast furnaces, I shall confine my discussion to those improvements and inventions pertaining directly to the blast furnace itself, omitting a number of patents pertaining to blast furnace operations. I spent the early part of my life in the construction of blast furnaces, from rivet-heating to drafting and designing, much of the work relating to repairs and rebuilding. Later, as I became more interested in maintenance and operation of a group of blast furnaces, one fact especially made a lasting impression on me, namely that a very expensive piece of equipment was very short lived, and the expense of replacement, relining, etc., in many instances consumed most of the profits made while in actual operation. As far back as 1910, I began to lay plans to build with a view to permanency and not merely for a blast, the common expression at that time, which really meant only one or two years in southern practice. Since we did not then blow so hard most failures occurred in the bosh and hearth. The failure of either generally meant a complete new lining, as the inwall did not look good enough to last another blast. At that time we were using two types of hearth, one of heavy steel plate protected by well and sprays on the outside, and .one of heavy. cast iron, made in sections and bound together with wrought-iron bands. The former type proved dangerous, for if the iron should come through, as it frequently did, it would cut away the steel plate, quickly turning large quantities of molten iron into the water, causing a severe explosion and costly repairs. The cast-iron type gave trouble also by the iron finding its way through the joints between the sections, which was&apos; not so serious; since the iron would not cut away the heavy cast-iron sections very quickly, and generally caused only small damage, and repairs-were easily made. Both types have been improved; the former by the introduction of cast-iron -water-cooled plates, placed on the, inside of the steel, jacket. This has proved to be very good construction, but has no real claim to permanency: As the cast-iron plates cannot be replaced from the outside, therefore the operator must assume that some time, at no late date, he must replace them from the inside, which will mean a blowing out of the furnace. The heavy cast-iron hearth has been improved by making the

Jan 1, 1928

By ED. E. Furman, R. H. Atkinson

HITHERTO the practical creep testing of precious metals has received little or no attention. The only previous creep tests of precious metals have been made with wires under conditions such as to yield much more rapid rates of creep than in engineering tests.&apos;, &apos; Up to the present time the value of creep bars of adequate size, in the absence of real need for engineering data, has deterred investigators. However, the increasing use of platinum at high temperatures has demonstrated the need for reliable creep data for the guidance of engineers, especially those engaged in designing certain specialized chemical plant equipment. In order to supply this need, creep tests were conducted at 1382°F (750°C) on 0.290 in. diam specimens of platinum, 90 pct Pt, 10 pct Rh and palladium. The platinum was high purity, nominally 99.95 pct Pt. The 90 pct Pt, 10 pct Rh was of the same high quality as is used for making gauzes for the catalytic oxidation of ammonia. The palladium was also of high purity; two batches of palladium bars were tested, one deoxidized with calcium boride and the other with aluminum. Spectrographic examination of the palladium confirmed its good quality; the only significant impurities apart from the residual deoxidizers were traces of silicon and lead. Procedure The creep bars, which were furnished by Baker and Co. to our specification, were 6 ¾ in. in overall length with a 4½ in. (4 in. gage length) reduced section 0.290 in. in diam and had the ends threaded (?-NC16). It may be of interest that the bars were valued at up to $600 each. The specimens were supplied in a 50 pct cold-worked condition to facilitate attachment of the creep extensometer, which was of the push rod type. Because of the softness of the platinum and palladium, the extensometer rings were secured to the test section by means of circular knife edges instead of the usual pointed set screws. The extensometer rods extended through the bottom of the furnace and readings were taken with a 0.0001 in. "Last Word" dial gage fastened to the rods for the duration of the test. The bars were directly loaded by hanging weights from the lower specimen grip. All tests were conducted at 1382°F ± 2°F, and an effort was made to maintain the temperature gradient over the test section within 2°F. The ends of the furnace tube were packed with asbestos wool, which allowed a very slow circulation of air through the tube. Annealing was accomplished in the creep furnace before the load was applied. The platinum and palladium specimens were annealed at the test tem- perature for about 17 and 24 hr respectively; in the case of the rhodioplatinum it was found expedient to anneal for 1 hr at 1922°F (1050°C). Pilot samples cut from the same stock as the bars were used to check annealing procedures. Pertinent measurements of grain size and hardness were recorded. Results and Discussion The creep data obtained are given in Table I and the creep curves are plotted in Figs. 1, 2, and 3. Two platinum specimens, tested under a stress of 250 psi, had almost identical creep rates at 2000 hr, namely 0.000008 and 0.000009 pct per hr. A third platinum specimen, stressed at 400 psi, had a creep rate at 2000 hr of 0.000026 pct per hr; the reason for a rather sharp decrease in creep rate during the period from 1200 to 1600 hr is unknown. As it was thought that 90 pct Pt, 10 pct Rh would have a lower creep rate than platinum, the first sample was tested at 400 psi; however, the creep rate was approximately 50 pct greater. Microex-amination revealed that differences in grain size might be responsible for the unexpected result, as annealing at 1382°F developed an average grain diameter of 0.0021 in. in the rhodioplatinum specimen compared with 0.004 in. in the platinum bar. Annealing the alloy for 1 hr at 1922°F (1050°C) increased the average grain diameter to 0.0032 in. and materially improved the creep resistance, making it much better than platinum. A second specimen annealed at 1922°F (1050°C) and tested under a stress of 550 psi had a creep rate of 0.000022 pct per hr at 2000 hr, which was still substantially lower than that shown by the specimen annealed at 1382°F (750°C) and stressed at only 400 psi. In contrast to the creep behavior of the platinum and rhodioplatinum specimens, the palladium bars, whether deoxidized with calcium boride or aluminum, were characterized by high first stages of creep. However, after about 1200 hr of test, the creep

Jan 1, 1952

By Glenn S. Wyman

CHUQUICAMATA, located in northern Chile in the Province of Antofagasta, is on the western slope of the Andes at an elevation of 9500 ft. Because of its position on the eastern edge of the Atacama Desert, the climate is extremely arid with practically no precipitation, either rain or snow. All primary blasting in the open-pit mine at Chuquicamata is done by the churn drill, blasthole method. Since 1915; when the first tonnages of importance were removed from the open pit, there have been many changes in the blasting practice, but no clear-cut rules of method and procedure have been devised for application to the mine as a whole. One general fact stands out: both the ore and waste rock at Chuquicamata are difficult to break satisfactorily for the most efficient operation of power shovels. Numerous experiments have been made in an effort to improve the breakage and thereby increase the shovel efficiency. Holes of different diameter have been drilled, the length of toe and spacing of holes have been varied, and several types of explosives have been used. Early blasting was done by the tunnel method. The banks were high, generally 30 m, requiring the use of large charges of black powder, detonated by electric blasting caps: Large tonnages were broken at comparatively low cost, but the method left such a large proportion of oversize material for secondary blasting that satisfactory shovel operation was practically impossible: Railroad-type steam and electric shovels then in service proved unequal to the task of efficiently handling the large proportion of oversize material produced. The clean-up of high banks proved to be dangerous and expensive as large quantities of explosive were consumed in dressing these banks, and from time to time the shovels were damaged by rock slides. As early as 1923 the high benches were divided, and a standard height of 12 m was selected for the development of new benches. The recently acquired Bucyrus-Erie 550-B shovel, with its greater radius of operation compared to the Bucyrus-Erie 320-B formerly used for bench development, allowed the bench height to be increased to 16 m. Churn drill, blasthole shooting proved to be successful, and tunnel blasts were limited to certain locations where development existed or natural ground conditions made the method more attractive than the use of churn-drill holes. Liquid oxygen explosive and black powder were used along with dynamite of various grades in blasthole loading up to early 1937. Liquid oxygen and black powder were discontinued because they were more difficult to handle due to their sensitivity to fire or sparks in the extremely dry climate. At present ammonium nitrate dynamite is favored because of its superior handling qualities and its adaptability to the dry condition found in 90 pct of the mine. In wet holes, which are found only in the lowest bench of the pit and account for the remaining 10 pct of the ground to be broken, Nitramon in 8x24-in. cans, or ammonium nitrate dynamite packed in 8x24-in. paper cartridges, is being used. This latter explosive, which is protected by a special antiwetting agent that makes the cartridges resistant to water for about 24 hr, currently is considered the best available for the work and is preferred over Nitramon. Early churn drill hole shots detonated&apos; by electric blasting caps, one in each hole, gave trouble because of misfires caused by the improper balance of resistance in the electrical circuits. Primarily, it was of vital importance to effect an absolute balance of resistance in these circuits, the undertaking and completion of which invariably caused delays in the shooting schedule. Misfires resulting from the improper balance of electrical circuits, or from any other cause, were extremely hazardous, since holes had to be unloaded or fired by the insertion of another detonator. The advent of cordeau, later followed by primacord, corrected this particular difficulty and therefore reduced the possibility of missed holes. After much experimentation, the blasting practice evolved into single row, multihole shots, with the holes spaced 4.5 to 5 m center to center in a row 7.5 to 8 m back from the toe. Such shots were fired from either end .by electric blasting caps attached to the main trunk lines of cordeau or primacord. The detonating speed of cordeau or primacord gave the practical effect of firing all holes instantaneously. Double row and multirow blasts, fired instantaneously with cordeau or primacord, proved to be unsatisfactory in the type of rock found at Chuquica-

Jan 1, 1952

By Alfred F. Brainerd

A few months since, Prof. Lawrence C. Johnson, of the U. 8. Survey, discovered in Mississippi large deposits of carbonate iron-ore, geologically located in the Claiborne formation of the Tertiary Epoch. These deposits are not pockets, but continuous layers or beds extending for miles, and can be located with certainty where they have not been removed by erosion. Upon examination, recently made by G. W. West, Birmingham, Ala., the largest deposits and highest grades of ore were found near Enterprise, Lauderdale county, and in Clark county, Miss. These beds measure from 10 to 18 feet in thickness, are superimposed upon a " burr rock," associated with green sand, and dip 30 feet to the mile southeast, at an altitude of 350 feet above sea-level, can be

Jan 1, 1888