Search Documents

By Per Larsson

The Chapin Mine, on the Menominee range, Lake Superior, was first opened in 1880 and has since then produced 1 1/2 million tons of soft blue hematite, containing about 63 per cent. of iron and 0.07 per cent. of phosphorus. Up to the present time, the ore has been mined from three separate lenticular deposits, which conform with the Huronian strata of the district, striking N. 75' W., dipping from 70' to 80' N., and pitching about 30' W. The largest of these ore-bodies has a horizontal length of 2500 feet, and a maximum width of 130 feet in the middle, from which it gradually narrows to the pointed ends. Its dimensions have not changed materially as greater depth has been attained. Figs. 1 and 2 show the geology and the mine-workings on the main deposit.. As this main deposit pitches away from the eastern part of the property, it is replaced by another lens, containing ore of the same quality. When first opened on the 1st level, this lens was 150 feet long and up to 50 feet wide, while now on the 6th level it shows a length of 550 feet, and a maximum width of 100 feet. It is separated from the extreme east end of the main deposit by about 30 feet of clay-slates It pinches out gradually between the slates to the west, and stops abruptly against the jasper to the east. Farther east in this belt of jasper occurs the third ore-lens which has a pretty regular length of 100 feet and averages, from the 1st to the 5th level, 20 feet in width. A cross-section of the ore-formation shows, on the north or hanging side of the ore, about 200 feet of clay-slates, and farther north a heavy belt of magnesian limestone. The slates and the dolomite are generally separated near the surface by a conglomerate of broken dolomite and soft slates. The foot-wall rock is also a clay-slate, containing a higher percentage of iron and less magnesia than the hanging-slate. Farther south occur alternate beds of slates and lean ore or jasper.

Jan 1, 1888

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.' This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By George A. Roberts, Robert F. Mehl

When austenite first forms from aggregates of cementite and ferrite, it is not homogeneous.' This inhomogeneity, consisting of both undissolved carbide and carbon concentration gradients, has a profound effect upon the characteristics of the austenite-pearlite reaction. The rate of formation of pearlite is increased by the presence of inhomogeneities2,3 and because of this (when the inhomogeneity is sufficiently pronounced) the hardenability of the steel is reduced.4,5 In addition to this kinetic effect, inhomogeneities will cause the direct formation of spheroidite from austenite at temperatures just below the Ael.6-11 The present report attempts quantitatively to evaluate the effect of inhomogeneity upon the rate of the austenite-pearlite reaction, presents a method of determining the austenitizing cycle necessary to obtain "practical homogenization," and considers the effect of inhomogeneity on hardenability. Effect of Inhomogeneities on Reactions Near Ae1 Few quantitative data are available representing the effect of undissolved carbide or of carbon concentration gradients upon the rate of the austenite-pearlite reaction. In procuring such data it is necessary to separate the effect of undissolved carbide from that of grain size, and this is not an easy task. The solution of carbide is always accompanied by an increase in the grain size, both effects contributing to the retardation of the reaction rate. It has been possible to make this separation and to obtain data that are independent of the grain size by the use of steels that differ only with respect to their tendency toward grain-coarsening. Steels C and D in Table I are such steels. These steels have been studied previously ;l,2,12 they differ only with respect to deoxidation practice; C was deoxidized with silicon while D, teemed from a portion of the same heat, was deoxidized with additional auantities of aluminum in the mold. C therefore is what is normally termed a "coarse-grained steel" and D is a, "fine-grained steel." These steels can be compared at the same grain size by heating c to a low temperature and heating D to an elevated temperature, producing a structure of austenite plus residual carbide in the former while forming homogeneous austenite in the latter; in such

Jan 1, 1943

By D. D. Pollock

Many constitution diagrams do not indicate the limits oJ solid solubility of the silver-rich solid solutions below 200°C. Thermoelectric measurements were employed to determine this limit in the nieighborhood of room temperature. The appearance of a second phase causes a discontinuity to occur in the tkevtrroelectric power as a function of cornposition at constant temperature and pressure. This discontinuity was employed to determine the limits of the silver-rich terzinal solid solutions of the Ag-A l, Ag-As, Ag- Bi, Ag--Ge, Ag-In, Ag-Pb, Ag-Sb, and Ag-Sn systenls at 30°C. CONSIDERABLE work has been done on the constitution of binary alloys of silver. The available data have been compiled by Hansen1 and Elliott.2 However, many of the binary diagrams do not show the limits of solid solubility of the silver-rich solutions below about 200° C. This work was undertaken in an attempt to extend these limits to the neighborhood of room temperature . PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pct (by weight) of impurities. The materials were weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony alloys were melted in A1203 crucibles, under a boric anhydride cover, and were poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles; they were also covered with boric anhydride and poured into split graphite finger molds. The $-in.-diam ingots were heated to 750°C and were forged and hot-rolled down to 0.1 by 0.1 in. The wires were pickled in a 25 pct HNO3-75 pct H2O solution to remove any oxygen-rich surfaces. The wires were then annealed at 550°C for 2 hr in a dissociated ammonia atmosphere. They were then furnace-cooled for 20 hr to room temperature in this atmosphere. The wires were cold-drawn to 0.0808 in. diam. The finished wires were again annealed at 550°C in the same manner as in the first anneal. Thermoelectric Power. The thermoelectric power of a single specimen of each alloy was determined against pure silver which contained a maximum impurity content of 0.014 pct by weight. The wire specimens were straightened and then cleaned with ethyl alcohol. They were then reannealed in the same way as the finished wires to assure that any residual stress would be at a minimum level. Previous work has shown that the presence of small amounts of stress has the effect of decreasing the thermoelectric power. The alloy specimen was soldered to the pure silver wire to form the measuring junction. A standard set of copper leads was then soldered to the reference junctions of the thermocouple. These junctions were maintained in separate dewar flasks which contained finely shaved melting ice during the test. The thermal electromotive forces of the thermocouples were measured at four temperatures between 15° and 45°C. A known source of electromotive force was balanced against the output of the thermocouple until a null balance was reached. The data were then expressed in terms of the thermoelectric power at 30°C. The results were then converted to absolute thermoelectric power, s303.3 These data have an average error of less than ±0.2 pct. RESULTS AND DISCUSSION All of the experimental data are given in Table 11. Since the electromotive forces of the binary alloys of silver were determined against the pure silver from which they were made, the resultant thermoelectric powers are only a function of the intentionally added binary elements at the constant test temperatures. This provides a direct measure of the effects of the alloying elements. The absolute thermoelectric power of an alloy of silver is given4 by:

Jan 1, 1968

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By E. C. Harder

CERTAIN typical characteristics of bauxites, ores of aluminum permit their classification into a number of categories, each of which has special features that enable grouping within it deposits from widely scattered bauxite fields. There may be local variations in conditions that have introduced differences of lesser importance between similar deposits in different fields, resulting perhaps from the influence of factors other than those that have produced the distinguishing features of each of the different groups, but in general the similarity between the deposits in each group is sufficiently striking to make the grouping indicated of interest. Several factors and conditions enter into the decomposition process that results in the development of bauxites and laterites and affects their character. The principal conditions favoring optimum bauxitization are: (1) pres- ence of rocks with easily soluble minerals yielding residues rich in alumina; (2) effective rock porosity, enabling easy access and free circulation of water; (3) normal to abundant rainfall alternating with dry periods; (4) vegetation, including bacteria, advantageously distributed; (5) available sources of appropriate solution and precipitation agencies; (6) a tropical or at least a warm climate; (7) low to moderate topographic relief, allowing free movement of the water table but a minimum of erosion; and (8) long quiet periods in earth history. Assuming that all of these factors are operating to a greater or less degree, it seems that the one that affects most the physical character of the resulting bauxite or laterite deposits is the chemical and mineralogical composition of the rocks that by their decay yield the bauxite deposits. This factor is used in the classification followed in this paper. In the process of weathering of ordinary silicate and carbonate rocks of the earth's crust, whether of igneous or sedimentary origin, it is the minerals of the alkalies that yield most readily to attack. The alkaline earth compounds also offer no great resistance, particularly the carbonates. Thus, among the rock-forming elements, those producing the most insoluble compounds are aluminum, iron, and silicon, together with certain ones of less importance, such as titanium, manganese, and phosphorus. In normal weathering processes such as prevail in temperate regions, the common minerals of rock decay are

Jan 1, 1952

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By C. W. Vaupell

The Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resurgence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barccnite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available. Introduction The Huitzuco mercury mines are of interest because of the unusual occurrence of ore in extinct geyser vents and the presence of several rare mercury minerals. Some of the deposits have typical characteristics of the telethermal zone and there is a gradation towards typical epithermal mineralization in depth. Halse,1 Villarel1o,2 Mactear3 and Merri114 have described the geology and the early operations in the district, and Bar-cena5 and Mallet6 have described the rare mercury minerals, livingstonite and barcenite, found at Huitzuco. Location The village of Huitzuco lies in the north central part of the State of (Guerrero, Mexico, 27 km. (16.7 miles) east of Iguala, which is the largest and most important town in the area. Iguala is served by the Mexican National Railways and also by the Mexico City-Acapulco highway. The highway is surfaced from Mexico City to Iguala, a distance of 200 km. (124 miles) by road, and there is a fairly good, level, dirt road from Iguala to Huitzuco. The elevation above sea level is about 1000 m. (3280 ft.). The climate is warm and very dry except during the rainy season, from June to

Jan 1, 1941

By F. W. Jessen, N. Lamont

The effect of an existing fracture or joint plane, which may exist in a rock, on the extension of a hydraulically induced fracture through the rock has been investigated in the laboratory. By use of a series of models made from various outcrop rocks, the width and orientation of existing fractures do not alter the extension or direction of the hydraulic fracture. The results, which conform quite well with the Grifith theory of failure, are illustrated by a series of photographs of the various models. INTRODUCTION The process of hydraulic fracturing has been widely used in the oil industry since its introduction in 1948 and has made possible the production of many reservoirs which would have been uneconomical prior to this process. Numerous studies of the mechanics of the process2-h nd of the effects of oriented fractures on recovery'.' have appeared in the literature. The increased recoveries led to attempts to predict the orientation of hydraulic fractures at the wellbore and to the development of methods to control this orientation. Field tests have been devised"." which indicate the validity of theoretical predictions of fracture orientation at the borehole. The direction of extension of hydraulic fractures from the borehole has not received much attention since most studies have predicted, at least implicitly, that a fracture will continue in the same plane unless a change of state of stress in the rock occurs. Since such predictions are based on the assumption of rock homogeneity, the effects of rock heterogeneities are left unknown. Most sedimentary rocks are composed of layers which reflect the changing depositional conditions of geological time. In addition, the more competent rocks frequently are fractured and jointed as the result of structural deformations or tectonic movements. Evidence of such joint systems exists in many surface outcrops, and it can be assumed that similar systems occur in many subsurface rocks, although the individual joints may be rather tightly closed due to overburden forces. This paper investigates the effect that an existing fracture in a rock would have on the direction or orientation of an extending or advancing hydraulic fracture when it intersects the existing fracture. The study was conducted on small rock models under triaxial stress conditions. The results indicate that an existing fracture will have little effect on the hydraulic fracture. THE MODEL STUDY The rock model represents an elemental portion of the earth containing an existing fracture which is located at some distance from a borehole from which hydraulic fracture is being extended. A generalized view of a model is presented in Fig. 1. The models were constructed from cement blocks and natural rocks. The various materials tested and some of the physical properties are listed in Table 1. The rocks were cut into rectangular blocks with dimensions of 11/2 X3Y2 X4 to 8 in. An initial slot was cut into the end face of each block along the longitudinal axis normal to the top face. The slot was filled with plastic aluminum along its outer edge to a depth of 1/16 in. A hole of 3/8-in. diameter was drilled into the sealed slot at the center of the end face to serve as an entry port for the fracturing fluid. Existing fractures of various types were simulated in the models. A "hairline" fracture with essentially zero width was created by cutting the model into two parts with a diamond saw and replacing the two parts together along the cut. A finite-width fracture was created by placing a layer of sand grains between the two faces of the cut just described (see Fig. 12). A large open fracture (similar, perhaps, to a vug) was created by cutting the model in two parts and removing a portion of the downstream block to a depth of % in. See Fig. 13. For a fourth

By C. G. Brehm

The anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal measures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof support and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches. The Lower, or Southern field, is made up of basins of great depth, some being 4000 ft. deep, and its measures are mostly on very steep pitches. In certain sections this Southern field is being mined at an elevation of 1300 ft. below sea level, on a pitch ranging from 50' to practically vertical, and because of the tremendous pressure and the inherent gas in the seams, outbursts of coal frequently occur at the face, locally known as "bumps." These outbursts are accompanied by a rumbling noise, after which gas is usually found. This condition makes mining a difficult and extremely hazardous undertaking, and unusual skill is required on the part of the miner to drive and maintain openings necessary to the production of coal. Miners working in such seams on the heavy pitch must carry face batteries (Fig. 1) to afford proper protection while working at the face, because of the outbursts and free running coal. To drive haulageways or gangways in this field it is

Jan 1, 1940

By C. G. Brehm

The anthracite-producing region is in the northeastern section of Pennsylvania, and has an area of approximately 484 square miles. It is divided geographically into three separate fields, known as the Northern, Middle and Southern. The Northern field, with Wilkes-Barre approximately at its center, is a basin about 60 miles long and almost 6 miles wide at its greatest distance across. Generally speaking, it may be said that the coal measures in this field lie horizontally, or on slight pitches, and consist of from 11 to 19 veins of coal, varying in thickness from several inches to several feet. The intervening strata between veins may be composed of slate, clay, rock or shale, or a combination of several, and are sometimes very thin. This condition often causes a treacherous roof, therefore roof support and the attending hazard of mining are problems of concern. The Middle field is made up of a number of small basins of not very great depth, and the measures, which are in like number to those of the Northern field, are varying inclinations running from nearly flat to steep pitches. The Lower, or Southern field, is made up of basins of great depth, some being 4000 ft. deep, and its measures are mostly on very steep pitches. In certain sections this Southern field is being mined at an elevation of 1300 ft. below sea level, on a pitch ranging from 50' to practically vertical, and because of the tremendous pressure and the inherent gas in the seams, outbursts of coal frequently occur at the face, locally known as "bumps." These outbursts are accompanied by a rumbling noise, after which gas is usually found. This condition makes mining a difficult and extremely hazardous undertaking, and unusual skill is required on the part of the miner to drive and maintain openings necessary to the production of coal. Miners working in such seams on the heavy pitch must carry face batteries (Fig. 1) to afford proper protection while working at the face, because of the outbursts and free running coal. To drive haulageways or gangways in this field it is

Jan 1, 1940

By Walter Stephen

MODERN developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constitu-ents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive opera-tion, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be oper-ated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6 ½ by 12 ½ -ft. Marcy rod mill ground from 625 to 820 tons. of ore per day to approxi-mately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier.. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1938

By N. M. Parikh, T. J. Koppenaal

The strengthening mechanism of fiber-reinforced silver has been investigated as a function of fiber density and fiber material. Stress-strain curves were determined in the range 2 x 10-6 to 2 x 10-3 plastic styain and slip lines were examined. The yield strength at 0.2 pct permanent strain is markedly dependent upon fiber density but the stress necessary to initiate plastic deformation is independent of fiber density. The strengthening mechanism of the fibers is shown to be malogous to grain boundary strengthening in poly crystalline metals. The variation in strengthening with different types of fibers is also noted and discussed. In recent years, considerable progress has been made in the understanding of the mechanical properties of two-phase systems, particularly in the classical dispersed-phase alloys where the separation between the dispersed phases is 0.01-0.1µ. However, little work has been done on fiber-reinforced metals where the dispersed-phase separation is considerably larger than this. Parikh1 investigated the mechanical properties of many fiber-reinforced metals and found that two general relationships are always observed, as follows: 1) A fibrous network incorporated into a second weaker metal strengthens the latter, and the amount of strengthening increases with fiber concentration. 2) At a corrstant fiber concentration, the amount of strengthening in a given matrix can vary considerably, depending upon the type of fiber employed. The object of the present investigation was to examine the fuiidamental factors controlling these two observations. procedure: Fig. 1 shows the initial step in the fabrication of the specimens. The sieve is shaken so that the fibers fall into a mold with the longitudinal axes of most fibers in the X-Z plane. The fibers are then compressed to a predetermined density, thus forming a "felt", and the necessary amount of matrix metal is added to the top of the felt. The mold is heated, in vacuum or hydrogen, to above the melting point of the matrix metal; the molten metal flows into the felt, and the entire assembly is cooled. This produces a "composite" that is essentially free of voids. A number of composites were prepared in this manner using 1/4-in. kinked lengths of mild steel

Jan 1, 1962

By Frank R. Hunter

INTRODUCTION Scope of Work Tins paper represents the results of an investigation of the presence, amounts, and degree of concentration of heavy minerals found in the pulp of the phosphate flotation plant at Peace Valley, Fla., which is operated by the International Minerals and Chemical Corporation of Chicago. In this paper, heavy minerals are those, excepting collophane, that sink in acetylene tetrabromide with a specific gravity of 2.95. Percentages of heavy minerals at several points of the flowsheet and the species of minerals have been determined. Some information as to the screen size of the minerals has been acquired. Previous Work All previous published reports or investigations of the deposits of heavy minerals in Florida have been limited to present beach sands. The mining operations conducted by the Humphreys Gold Corp. about seven miles east of Jacksonville along an ancient shore line have been described in trade journals, but descriptions of the minerals have been lacking. Commercial grades of ilmenite, zircon, and rutile are produced on a large scale. Papers have been published on heavy minerals found on the Florida beaches.I-6 Location "International's" Peace Valley flotation plant is in south-central Polk County, Fla. about eight miles south of Bartow and along the Atlantic Coast Line Railroad. The mine surrounds the plant and includes about 1500 acres of the phosphatic lands in this area. GEOLOGY General Setting All of the rock underlying the area is almost horizontal. The oldest bed exposed is part of the Hawthorn phosphatic limestone of Miocene age. This outcrops in the stream bed of the Peace River about one mile east of the plant. Elsewhere the Hawthorn is covered except where it has been exposed by mining operations. The Bone Valley formation of Pliocene age, which is the phosphatic stratum extensively mined in this area, unconformably overlies the Hawthorn. Resting unconformably upon the Bone Valley formation are Pleistocene (?) terrace deposits of unconsolidated quartz sand which comprise the overburden of the phosphate ore. Stratigraphy Hawthorn formation: "Bedrock" of the pebble phosphate deposits is a cream to white colored, sandy, dense limestone containing varying amounts of small grains and nodules of collophane. The upper surface of the formation is undulating and irregular showing evidence of former

Jan 1, 1947

By Eugene Guccione

Evidence that the United States is gradually converting to the metric system of measurement can be perceived today even by housewives in a supermarket. The question is no longer whether but when the country will have completed the conversion. To the extent that any bickering about metrication still exists, the debate now centers on such issues as finding agreement on details of implementation, and whether federal legislation should speed up the metric-conversion process or allow it to proceed along its present evolutionary and voluntary course. Apparently, the voluntary or "make-haste-slowly" approach is gaining widespread support. According to The Research Institute of America, Inc., if and when federal legislation is enacted it will likely include the following national ground rules: (1) A National Metric Conversion Board will develop and submit to the President and Congress a comprehensive plan to achieve a coordinated, minimum-cost changeover. (2) The change- over will be completed 8 to 10 years after the board's plan goes into effect, and by that time the US will be predominantly, though not exclusively, metric. (3) Costs will "lie where they fall"; subsidies, special tax concessions, and antitrust exemptions will not be authorized by the legislation. (4) The changeover will be voluntary because of the recognition that while some firms can "go metric" in a matter of weeks, others may require 15 years or more, and a few might never convert. (5) In determining whether or not to convert, on an individual company basis, adherence will be to the "rule of reason-that is, ". . . do not convert unless the engineering, economic, or other benefits outweigh any metric-related disadvantages. No one is talking about rip- ping up our railroad tracks or rewiring our homes just to conform to the practice of metric nations in Europe." (6) Government is to be part of the solution, not part of the problem; in effect, says The Research Institute of America, the leverage of federal procurement will not be exerted to force-feed the metric changeover but will be coordinated with the sector-by-sector conversion of the economy.*

Jan 12, 1975

By A. S. Eve

IN the spring of 1930, the question was raised as to the possibility of estimating the depth to which the pyrrhotite-nickel deposit at the Falconbridge mine extended in the earth. This body is 7500 ft. long, it dips at 80° to the north, and it is fairly straight with slight sinuosities. Dr. F. W. Lee suggested that it might be possible to solve the problem by measuring the vertical magnetic intensity, with a good magnetometer, both near the surface of the earth and also at a level a 'few feet higher in the air. The writer regarded this suggestion with some scepticism, but it was decided to put the scheme to a prac¬ tical test. In July, 1930, Dr. Lee, Dr. Keys and I ' the writer, with Mr. Joyce and Mr. Belloc as assist¬ ants, made a firm, light wooden platform (Fig. 1) E measuring 4 by 4 ft. on the top, which was 10 ft. above ground. This platform could be moved easily a few yards by four men, and carried across I country in a wagon or by motor truck. Some iron nails were used in its construction, but we were not able to detect their influence on the - Askania magnetometer. Nevertheless, in future work, the use of iron should be completely avoided. Readings were taken along a traverse at right L angles to the orebody, at several stations, both on FIG. 1.-VERTICAL the ground and on the platform. The excess read- ASKANIA MAGNETOM¬ ETER ings, over the dike, as compared with those about 10 ETER ON A FT. HIGH. PLATFORM 800 ft. away, are shown in Table 1. The largest reading, 6.8, is open to suspicion and should be rejected. The depth of the top of the orebody is known by electrical survey, and by actual drilling, to be about 112 to 123 ft., and the covering is sandy glacial drift. Similar readings were taken over a long straight magnetic diabase dike. These also are shown in Table 1. The magnetic vertical intensity is consistently less at the higher level, which is l0 ft. above the lower level.

Jan 1, 1931

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By Walter M. Stephen

Modern developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted and covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6½ by 12½-ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1939

By B. C. Craft

Development and exploratory work in Mississippi during 1934 was rather active, resulting in the expansion of the proven area and the drilling of a number of important wildcat wells. Mississippi showed a decrease in drilling operations during 1934. There were 36 completions from 18 counties during this period compared with 58 completions from 22 counties during 1933. There was a considerable decrease in activity in the Jackson gas field in Hinds and Rankin counties with only 9 completions, resulting in 8 gas wells and 1 dry hole compared with 17 gas wells, 2 oil wells and 7 dry holes during 1933. Leasing and geophysical work was reported from several sections of Mississippi last year. Extensive exploration and drilling were carried on in Lamar, Hancock, Pearl River, Greene and Stone counties and on the flanks of the Jackson anticline. Exploration will be continued in these areas during 1935. Four important wildcats were completed during 1934, all of which were reported as being structurally high, but without having important shows of oil or gas. These tests were: Hix and Germany's, J. J. Newman Lumber Co. No. 1, sec. 21-4N.-15W., Lamar County, abandoned at 3520 it. in the Wilcox; United Gas Public Service Company's Davis No. 1, sec. 30-1N.-5W., Greene County, abandoned at 7439 ft.; Gulf Refining Company's May L. Williams No. 1, sec. 33-5S.-17W., Pearl River County, abandoned at 4800 ft.; and Clarke County Oil Company's S. B. Kirkland No. 1, sec. 10-2 N.-16E., abandoned at 4002 ft. in the Eutaw. Another interesting wildcat was Gulf Refining Company's Dantzler Lumber Co. No. 6, sec. 22-4S.-llW., Stone County, abandoned at 7700 ft. (according to reports below the Selma chalk). A total of 114 of the 132 gas wells completed in the Jackson gas field are still producing and have a combined open-flow capacity of 4,145,-696,000 cu. ft. Four of the abandoned gas producers were never connected to the lines. The open-flow capacity of three wells in the Amory field is approximately 1,000,000 cu. ft. Producing against a line pressure of 50 lb., the demand during December greatly exceeded the capacity.

Jan 1, 1935

By Werner Schwartz, Wolfgang Haase

Lead sulfide concentrates, which may include other lead concentrates, are sintered on an up-draught sintering machine without the addition of any diluting agents or fluxes. Subsequently they are melted in an oil- or gas-fired rotary furnace. The sintering and melting processes are based upon the following roast-reaction: PbS + 2 PbO = 3 Pb + SO, PbS + PbSO, =2 Pb + 2 SO, For obtaining a lead bullion free from sulfur, the sintering process is carried out in such a way that the sinter product contains a small amount of excess oxygen above that to react with the sulfides. At the end of the melting process, when the reactions are finished, the remaining small amount of oxide residues is reduced with coal to which a certain percentage of soda ash (about 1 pct of the lead bullion) is added. For the lead smelting process described neither coke nor fluxes—except soda ash—are required. This process is being utilized by a European smelter successfully and with a high lead recovery. The consumption figures for the smelting of 100 tons per day of lead concentrates are indicated. The lead content of the lead concentrates from modern ore dressing plants ranges from 65 pct to above 80 pct. In most lead smelters of the world these concentrates are smelted in a blast furnace. For blast-furnace smelting the concentrates have to be desulfurized and agglomerated by sintering. A requirement for the perfect operation of a down-draught sintering machine and of a blast furnace is a maximum lead content in the feed of 40 to 45 pct. For this reason, some lead concentrates have to be diluted by adding return slags, limestone, and possibly iron oxide and sand. As an example, 100 tons of lead concentrate with 72 pct Pb would contain 13.5 tons of gangue (including the zinc). To produce a perfect sinter with 42 pct Pb it would be necessary to add 70 tons of flux and return slag, more than five times the original weight of the gangue, to the sinter mix and blast-furnace charge. A correspondingly large amount of coke would be required in order that all of these materials reach the heat of formation and the melting temperatures of the slag (1200" to 1400°C) inside the blast furnace. The roast-reaction process presents a possibility for lead recovery without dilution of the concentrates. In this process the concentrate mixed with coal is placed upon a Newnam-hearth and air is blown through nozzles into the heated mix. AS a result metalllic lead and a relatively great amount of so-called .'Grey Slag" with a lead content of 25 to 35 pct are formed. The slag is sintered to eliminate sulfur and, after addition of the requisite fluxes, treatt:d in a blast furnace. Owing to the poor recovery of lead from the hearths and to the unavoidable heavy hand-work plus the risk of poisoning this process is utilized in very few 112ad smelters today. Since in mxny countries of the world coke is expensive and difficult to obtain, it appeared feasible to use the principle of the roast-reaction by modern sintering and melting methods with recovery of the lead in electric, or oil, gas, or coal-fired furnaces. Two processes are utilized on an industrial scale: A) Lead smelting in the electric furnace of the Bolidens Gruv A/B in Sweden, as described by S. J. Walldcn, N. E. Lindvall, K.G. Gorling, and S. Lundquist. B) The self-fluxing lead smelting of Lurgi Gesell-schaft fiir Chemie und Huttenwesen m.b. H., Frankfurt a M, Germany, which is described in this paper. In the Boliden process referred to above the sinter mix is pelletized by enveloping return fines with layers of flue dust, limestone powder, and dried galena concentrate. The roasting and agglomeration are carried out on a down-draught machine, and a slight excess of sulfur is left in the sinter product. During the smelting in the electric furnance the roast-reactions occur and a slag poor in lead and a sulfur bearing lead are formed. This latter is subsequently oxidized in a converter to obtain lead bullion and dross. The Lurgi-process achieves the maximum possible extent of the roasting reaction on the sintering machine. The wet flotation concentrates are blended with return fines (lead content 70 to 80 pet), any existing flue dusts and lead slimes—but without the

Jan 1, 1962