Search Documents

By Haim Chiswik

IN recent years considerable attention has been devoted to the devel-opment of new commercial uses for silver, chiefly because of lowered prices and large stocks of the metal. This has led to increased interest in the phase diagrams of silver alloys. The silver-lead diagram is reported' to be of the simple eutectic type, but no measurements of the solubility of lead in silver have been made. The solubility of silver in lead has been estimated2 from diffusion experiments and resistance measurements to vary with temperature from 0.09 to 0.18 atomic per cent (0.05 to 0.10 weight per cent). Silver-rich silver-lead alloys have recently been recommended as high-strength bearing metals.3 The silver-bismuth diagram is similar.' The solubility of bismuth in silver has been estimated to be about 5.5 weight per cent on the basis of X-ray work.4 Matthiessen5 found a solubility of silver in bismuth from 0.25 to 0.50 per cent by conductivity measurements. Silver and thallium form the same type of diagram,1 with no data on their mutual miscibilities. We have studied the first two of these diagrams by X-ray methods, verifying their main features and determining the solubilities of lead and bismuth in silver at several temperatures. We also determined the solubility of thallium in silver at one temperature. The solubilities of silver in lead and in bismuth were found to be too low to be detectable.

Jan 1, 1940

By John J. Borkert, Carl E. Gerity

In situ mining offers a new and proven method of exploiting sedimentary uranium deposits. The feasibility and economic evaluation of exploiting a uranium reserve by either open pit or underground mining should also include a similar study for in situ mining. This report compares the economics of mining several hypothetical uranium deposits at various depths, grades and reserve sizes by open pit and in situ mining. The evaluation process evolved establishing, where possible, common geological and logistical parameters to both methods of mining. The various assumptions that are unique to either open pit or in situ mining were also drafted, where possible, as equal and common functions to be used in each economic evaluation of the reserve models. After the various parameters were defined, they were programmed to an economic analysis of the various hypothetical uranium deposits by the selected mining method. From the vast array of cost evaluations, total capital and operating cost per pound U308 produced, DCF-ROI, and total net profits before State and Federal taxes were selected as the most meaningful results to compare. From the various geologic parameters used, it was determined that the economic viability of a mining venture is most sensitive to a depth-grade thickness ratio. The three selected evaluation products were plotted against the various depth-grade thickness ratios of the hypothetical uranium deposits. The results of the economic cost analyses show in situ mining generally to be a better method to maximize total net profits and to maximize return on investment.

Jan 1, 1979

Article IX of the Bylaws constitutes the basic instructions to the Nominating Committee The first duty of the Nominating Committee is to select a candidate for Director and President-elect It is desirable that the successive Presidents from year to year be men of differing professional interests so selected that over a period of years each major group in the Institute will be represented in the Presidency a number of times bearing some reasonable relationship to the numerical strength of that group in the Institute In Section 2 of Article IX it is stated that "a sufficient number of Directors be selected on the basis of geographical districts so that each district will have at least one representative" These districts, as now established, are shown in the accompanying map There are ten districts including the New York metropolitan district Each of these districts is entitled to one Director, except the metropolitan district which is entitled to six Each year each district, the term of whose officially recommended Director expires, shall suggest a candidate and if desired an alternate candidate to the Nominating Committee to fill the vacancy If a candidate and an alternate are suggested they should preferably have different Divisional or Branch affiliations The Chairmen of the Sections In the district shall constitute a committee to select the candidate or candidates The Sections shall rotate the chairmanship, as shown in the Appendix to this instruction It is desirable that in filling a quota vacancy in any district, the selection be made from the name or names suggested by the district

Jan 1, 1952

By W. Spencer Hutchinson

THE purpose of this account is to introduce to other engineers and geologists who use photography a means of interpreting topographic and geologic structure with the stereoscope. Anyone who finds this of sufficient interest to read it at all must cut out the pictures shown and have a good look at them through the stereoscope; there is no other way to appreciate what is meant. Most of us have been disappointed by the flatness of mountain pictures and by the lack of perspective in photographs taken to illustrate topographic and geo- logic features. The use of the stereoscopic principle was suggested by the work of the photographic division of the Air service during the war. Photographs of the battle line, taken from air planes, were mounted for stereoscopic study, with most remarkable development of topography, penetration of camouflage and, by the matching of pictures with a time interval between, sure revelation of new work by the enemy. Thus, two views taken from a plane flying at 10,000 ft., both of the same terrain but from different points, are mounted in proper relation and put into the stereoscope. If the distance between the two positions of the camera was 200 ft., the observer then sees the topographic and military features as though his eyes were 200ft. instead of 235 in. apart.. The result is startling in its revelation of features that are flat and unintelligible when viewed by the unaided eye or in a single photograph. The technic of the work, as developed during the war, was quite complex and

Jan 1, 1921

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

Continuing tantalum alloy development studies have been concerned with a more detailed investigation of promising binary, ternary, and more complex tantalum alloys containing Groups IV-A, V-A, VI -A. VII-A, and VII-A metal additions. A primary objective of these studies was to improve the elevated temperature strength of tantalum with minimum degradation of fabricability and low-temperature ductility by alloying. Several alloys were found to exhibit hot tensile strengths in the excess of 25, 15, and 10 ksi at 2700°, 3000°, and 3500°F, respectively, combined with excellent cryogenic toughness and ductility. Particularly outstanding in this respect are alloys in the system Ta-Mo-W. Ternary parameter curves describing hot-strength, low-temperature ductility, recrystallization temperature, weld ductility, and fabricability are presented for the Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W systems. At present, only four metals qualify for large scale structural applications at temperatures above about 1800°F. These are tungsten, tantalum, molybdenum, and columbium. Research and development work on these refractory metals has progressed to the point where efforts are now primarily directed toward the improvement of high- and low-temperature mechanical properties through alloying. High melting point combined with excellent low-temperature ductility, fabricability, toughness, weldability, and high solubility and tolerance for both substitutional and interstitial solutes are important attributes of tantalum. Conversely, its high density and relative scarcity compared with other refractory metals are the major deterrents to the use of tantalum. Early studies in the Battelle alloy development program established base line data on the mechanical and metallurgical properties of high-purity tantalum.' These studies were extended to include a preliminary investigation of the effects of various alloying elements on the established base properties.2,3 Recent studies involved a more detailed investigation of promising binary alloys containing Cb, Hf, Mo, Os, Re, Ru, and W, and ternary Ta-Cb-V, Ta-Hf-W, Ta-Mo-Hf, Ta-Mo-V, Ta-Mo-W, and Ta-V-W alloys. Results of major importance obtained are given in this article. EXPERIMENTAL PROCEDURES Electron-beam-melted tantalum (Wah Chang) and high-purity alloying elements were consolidated as 150-g ingots by multiple nonconsumable arc melting under a partial atmosphere of helium. Homogeneity of the button ingots was checked radiographically. Alloy buttons measured about 1-1/2 to 1-3/4 in. in diam by about 0.35 and 0.50 in. thick. Nominal alloy compositions were checked on each alloy button by weighing after arc melting. In most instances, weight losses were within 3 pct of the total weight charged. Subsequent chemical analyses on a number of selected alloys showed interstitial contents to range as shown below: Range of Interstitial Content, ppm 0 C N H 25-75 50-100 10-50 1-5 Metallic alloying additions were found to agree well with nominal compositions based on weight change data. Fabrication directly from the cast button to sheet was conducted at low (75° to 900°F), intermediate (1800° to 2000°F), or high (3000°F) temperatures, depending upon alloy content and hardness. Evacuated stainless steel or molybdenum packs were used for fabrication at intermediate and high temperatures, respectively. The temperature required to complete recrystal-lization in one hour was determined by hardness measurements and metallographic observations (longitudinal test sections) after vacuum annealing at 180°F intervals in the range 2010° to 2910°F. All mechanical property evaluations were conducted on recrystallized sheet, nominally 0.04 in. thick. Weldability of the various alloys was screened using manual TIG welding techniques. Bend ductility (bend axis perpendicular to weld axis) was the criterion used for evaluation. Tensile specimens employed 0.200 by 1 in. gage lengths, and bend test specimens measured about 1 by 1/4 in. Low-temperature tensile tests were conducted using a crosshead speed of 0.02 in. per min up to the point of yielding, and 0.05 in. per min to fracture. High-temperature tensile tests were conducted in vacuum using a crosshead speed of 0.01 in. per min

Jan 1, 1963

By C. W. Allen, B. D. Cullity

The proportional limit of iron crystals in torsion is governed by the resolved shear stress in the most highly stressed slip systems, averaged around the specimen circumference, and does not obey a critical resolved shear stress law. Crystals of most orientations exhibit a stage of easy plastic deformation, akin to easy glide in tensile or shear specimens. Transient deformation, similar to that which occurs in single crystals of other materials, is also observed. THE torsional deformation of single crystals of magnesium (hcp) and aluminum (fcc) has been described recently by Choi et al.,&apos; especially with respect to the criterion for the orientation dependence of the onset of plastic flow in these materials. The purpose of this paper is to present results of torsion tests of iron single crystals and thus to extend this yield criterion to a bcc metal. In addition to considering the variation of proportional limit with crystal orientation, this paper also briefly treats work hardening, transient deformation, and the mechanism of plastic flow in iron. The effects of the method of surface polishing and the chemical purity of the iron have been investigated. STRESS DISTRIBUTION It is convenient to express the stress at any point of a cylindrical crystal stressed in torsion in terms of t0, which is the shear stress acting at the surface on a plane normal to the axis of the cylinder and in a direction tangential to the cylinder. This stress is given by To = 2T/pr3 [1] where T is the applied torque and r the specimen radius. The shear stress t, resolved in any chosen slip system is given in terms of 7, by1 Ts/TO = sin 0, cos d sin (0, -) + cos , sin d sin d - ) [2] where 0 and d are the angles between the specimen axis and the slip plane normal and slip direction, respectively; h is the angular circumferential position on the specimen at which t, is being determined, measured from an arbitrary reference plane which includes the axis;o and d are the angular coordinates of the projections of the slip plane normal and slip direction on a transverse section with respect to this same reference plane. Slip in iron occurs in a <1ll> direction on the {ll0}, (1121, and (123) planes, which together comprise 48 slip systems. A complete evaluation of the stress distribution in an iron crystal stressed in torsion would therefore require a calculation of Ts/T0 as a function of for 48 different slip systems. Fortunately Gough,&apos;who studied the behavior of iron crystals in alternating torsion, was able to simplify this problem considerably. He showed that it was sufficient to consider a kind of average slip plane for each slip direction, namely the mathematical plane of maximum resolved shear stress containing the slip direction considered. This simplifying approximation is possible because, for each slip direction, the active slip plane or planes lie very near this mathematical plane of maximum shear stress. Vogel and rick&apos; have critically reviewed the early work of Taylor and Elam,13 Taylor,14 and Fahrenhorst and schmid8 from which the identification of the above crystallographic planes as slip planes in the bcc lattice largely stems. While their criticism is clearly justified, their own results do little to clarify the issue. The role of cross slip (screw dislocations changing glide planes) is evidently so important in this case, as Read3 has suggested, that methods for deducing slip systems from observations of gross slip traces are inadequate, such traces commonly arising from complex dislocation motion. Thus the treatment given here involving the plane of maximum resolved shear stress seems a logical simplification especially in view of Gough&apos;s2 study of a iron. There is, however, an assumption built into the subsequent treatment the comparative validity of which is difficult to assess, namely, that slip in all slip systems in iron may be characterized by a common critical resolved shear stress. The shear stress 7, resolved in a slip direction defined by d andd, and on the plane of maximum shear stress containing this direction, is found by first maximizing 7s/70 with respect to either Oo or 4,. The slip plane coordinates are then eliminated by using the relation between 0, ,o and d, d, namely,

Jan 1, 1963

By E. E. Underwood, L. L. Marsh

Aluminum single crystals, alloyed with 0.042 atomic pet Cu and 0.11 and 1.1 atomic pct Mg, were subjected to constant stress creep tests, tensile tests, and hot hardness measurements within a temperature range of 300° to 866OK. Calculations based on Dorn&apos;s temperature-compensated time parameter, 6, gave a value of DH, = 27,000 cal per mol for the activation energy of early creep in aluminum single crystals. Correlations have been obtained for aluminum alloy single crystals with the parameter E for solid solution strengthening, as well as with the parameter F for solid solution hardening, by using a valence of three for aluminum. Limited measurements on tensile specimens show that the slip band density tends to decrease with increasing temperature and with decreasing solute concentration. INCREASING interest is being shown in the mechanisms of plastic deformation in single crystals during tensile and creep testing. The complexity of deformational processes in polycrystalline materials has led to a search for simpler experimental conditions. Numerous creep and tensile investigations have been conducted with pure, metallic single crystals. To a lesser degree, the effects of alloying elements on the tensile properties of single crystals have been determined. However: the literature dealing with the effects of alloying additions in single crystals under creep conditions is vanishingly small. This paper represents an attempt to narrow this gap in the knowledge of the subject. Previous investigations of creep behavior at the Battelle Memorial Institute1-1 have been of great value in the analysis of the present single crystal data. It is equally desirable, however, to ascertain the extent of correspondence between the behavior of single crystal and polycrystalline materials. For this purpose, correlations, similar to those developed for polycrystalline aluminum alloys by Dorn and co-workers, have been made with the single crystal data. The results from this study have tended to confirm and extend those correlations to the case of alloyed single crystals. Materials and Procedures Three dilute binary aluminum alloys were prepared for this investigation from 99.99 + wt pct Al, 99.8 wt pct Mg, and 99.92 wt pct (electrolytic) Cu. The nominal compositions of the alloys were 0.042 atomic pct Cu, and 0.11 and 1.1 atomic pet Mg. Precautions were taken to avoid contamination of the stock during melting and casting of the alloys. After a heat treatment of 8 hr at 925°F the alloys were extruded, then machined into) threaded tensile specimens with a 3 in. reduced section and a 0.505 in. diam. Spectrographic examination showed less than 47 ppm metallic impurities in each alloy. The single crystals were grown by the strain-anneal method, with a critical strain of about 11/4 pet giving the optimum results. In general, 3 in. crystals were obtained with the Al-Cu alloy, but smaller crystals in the magnesium alloys necessitated the use of 2 in. and 1 in. gage lengths with the low and high magnesium alloy specimens, respectively. After an electrolytic polish, the orientation of that portion of the specimen containing the largest single crystal was determined from Laue back-reflection photographs. Tensile tests were conducted at a constant load rate of about 2 lb per min. Creep runs were made in a constant temperature room, under constant stress at the higher creep temperatures, and constant load at the lower temperatures. The eloneation was measured to within ±5 microin. by a specially designed capacitance extensometer. The ex-tensometer arms were attached to the 3 in. specimens at the shoulders of the test piece or, where the crystals were smaller than 3 in., by knife-edge grips.

Jan 1, 1957

By I. M. Bernstein

The steady-state creep behaviov of zirconium and zivcaloy-2 was examined in the temperature vatlge 520° to 620°C A1 low stresses the creep rates were cimracterized by a linear stress dependence; at highev stresses the stress dependence was much more pronounced. Temnperature-cycling tests yielded values for the aclivation enevgy for creep. Various tlzeories were examined in the ligltt of- the experimental re-sults and it mas concluded that the low-stress creep behavior is the result of the stress-direcled diffusion of vacancies along gain boundaries. It has been observed,"&apos; usually under conditions of high temperature and low stress, that creep deformation can occur for which the steady-state creep rate is linearly dependent on the applied stress. For magnesium and certain magnesium alloys, Harris and ones&apos; and ones&apos; have argued that this type of creep occurs by mass transfer as a result of the stress-induced generation and migration of vacancies, along a gradient defined by the stress direction. Jones&apos; demonstrated that the rate-controlling diffusion path is sensitive to grain size and temperature, and that by suitable control of these variables creep could occur by vacancy diffusion either predominately along grain boundaries or through the lattice. Recently, Jones3 suggested from an examination of limited high-stress data for zircaloy-2, composition in Table I, that significant diffusion creep could occur at low stresses, at least between 375" and 500°C, controlled by grain boundary vacancy diffusion. This process could have an important implication in assessing the role of zirconium alloys as a structural or cladding material in certain classes of nuclear reactors, since it predicts creep deformation far in excess of any estimates based on extrapolating slip creep data from higher stress levels. If the diffusion creep process occurs it should be possible to describe the total steady-state creep rate of zirconium and its alloys as the sum of two terms, Eq. [I]; the first term relates to a slip creep process important at high stresses and which is manifested by a much more pronounced dependence of creep rate on stress4 than diffusion creep and the second to a process controlled by mass transfer,5&apos;6 dominant at low stresses: where A and BI are parameters which can depend on structure, Ql and Q2 are the activation energies for the particular creep process occurring, and n describes the sensitivity of the creep rate on stress. It is the purpose of this paper to present some direct experimental evidence in support of this view. It is recognized that other analytical approaches have been proposed to explain data of this kind and these will also be discussed. 1) EXPERIMENTAL PROCEDURE Flat creep specimens (gage length 1 by 0.25 by 0.02 in. approx) were prepared from cold-rolled, argon-remelted, crystal bar zirconium and cold-rolled commercial-grade zircaloy-2, the analyses of which are given in Table I. The specimens were annealed at a pressure of < 10-5 Torr at temperatures from 625" to 675°C for 2 hr and slow-cooled. This treatment produced stable grains of average size (defined here by the average linear intercept) of for zirconium and -4xin. (-10 p) for zircaloy-2. The specimens were tested in a dead load tensile creep rig. The stress was maintained constant by adjusting the applied load after approximately each 1 pct of strain. The specimen temperature was controlled to better than +1°C. This system had a small thermal lag, so that rapid temperature changes were possible. To minimize corrosion, the specimens were tested in high-purity (99.95 pct) argon, further dried,

Jan 1, 1968

By W. R. Kanne, P. R. Strutt, R. A. Dodd

A study has been made of the creep behavior of ß-NiAl of stoichiometric composition in the temperature range 475" to 775°C. Single crystal tensile specimens were deformed under a constant applied load. From slip line studies and tensile axis rotations it was concluded that the crystals deformed by pencil-glide on (100) and (110) planes with a (100) slip direction. Electron microscope thin-film studies showed evidence for profuse cross-slip, and the dislocation Burgers vector was determined to be (100). There was no tendency for the dislocations to lie in definite slip planes, although a strong alignment of segments of edge dislocations was frequently seen. The activation energy for creep in the temperature range 475" and 775°C was judged to be much lower than that for creep at temperatures above 775°C. It is possible that the rate-controlling process is the thermally activated cross-slip of screw dislocations. In recent years considerable interest has developed in the possible use of high-melting-point intermediate phases for high-temperature applications necessitating good creep resistance. Ordered alloys such as Ni3A1, modified by alloying additions, have received particular attention, culminating in the recent development by Pratt and Whitney of single crystal turbine blades.&apos; The intermediate phase NiAl has considerable theoretical interest from a creep standpoint because not only is it ordered up to the melting point (-1650°C at stoichiometry) but it contains a high concentration of structural vacancies on the aluminum-rich side of stoichiometry. These vacancies are known to exert a strengthening effect under some conditions,&apos; but in addition they might be expected to affect high-temperature creep rates through dislocation climb. The present paper deals with the slip line and dislocation structures developed during creep of stoichiometric NiAl between 475" and 775C, and with possible attendant creep mechanisms. MATERIALS AND TEST TECHNIQUES NiAl ingots of stoichiometric composition were prepared by induction melting 99.996 pct A1 and 99.98 pct Ni (kindly provided by the Kaiser Aluminum Co. and the International Nickel Co., respectively) in 100 cc pure alumina crucibles in a helium atmosphere. No chemical melting flux was used in order to avoid con- tamination of the alloy. Each ingot was slowly direc-tionally solidified to avoid porosity and to produce very large grains up to 2 in. in length. In this way, ingots were obtained which were suitable for sectioning into single crystal creep specimens. Chemical analysis indicated that all alloys were within the range 49.6 0.3 at. pct Ni. For the present investigation, identical rectangular single crystal blanks were cut vertically from one particularly large crystal in an ingot using a series of three diamond cut-off wheels with appropriate spacers. Thus, all sliced crystals had the same orientation with the tensile axis parallel to the long side of the rectangle; the initial orientation of the tensile axis is shown as S, in Fig. 1. The blanks were homogenized at 1250 to 1300°C for 48 hr and subsequently cooled slowly to room temperature. A gage length of rectangular cross section and about 0.75 in. in length was prepared on each specimen using an electrolytic lathe and a dilute nitric/phosphoric acid electrolyte. The gage length cross section was 0.250 0.0005 in. by 0.040 ± 0.0005 in. Holes to accommodate tensile grips were electrolytically machined using a rotating acid jet. After creep testing, this same technique was used to cut discs for transmission electron microscopy. Thus, all shaping was done electrolytically, the only exception being that (122) sections were spark-machined from some speci-

Jan 1, 1970

By C. P. Sandberg

C. P. Sandberg, London, Eng. 1 think we should all be grateful to the Pennsylvania Railroad Company, and to their chemist, Dr. Dudley, for spending so much time and money in order to solve an important question; nor are me less indebted to the public spirit which leads them to impart tlie experience thus gained. In Europe nothing similar has hitherto been done, either by a company or by any private individual. In England the great railway companies employ their engineers in other ways, and do not keep a chemist or specialist to study rails; bat even if they did they would probably not publish the results. The chief professional engineers are so occupied with their private practice of railroad construction generally, that they cannot be expected to devote their time and energies to so special a question. The German Railway Union has, in my opinion, missed the real object of its elaborate researches by falling into the error of specifying costly, impracticable tests for rails—tests at the same time which do not infallibly expose the impurities that may be in the rails under examination. There has, therefore, been nothing done on this side of the Atlantic in the way of exhaustive study to determine the best composition for steel rails. America should consequently have full credit for the enlightened example which she has set. I wish, however, to make a few remarks on Dr. Dudley&apos;s second paper,—& paper which follows very much upan the same lines of argument as the first red three years ago, upon which I have previously touched in my pabr on the same subject read at the meeting in August last. If Dr. Dudley had discovered a new metal he could hardly, I think, have taken wore pains to prove that he was correct in his first formula for the best chemical colnposition of steel rails. But I hare seen so much done in the way of proof by experiment that I am inclined to think that almost anything can be proved by experiments and by satnples. If Dr. Dudley would only give up his formula, which would not suit any country—not even America—

Jan 1, 1881

By R. L. Pober, L. Kaufman, E. V. Clougherty

Composite structure of hafnium, zirconium, and titanium diboride with additions of metals and/or compound phases were prepared by reactive high-pressure hot pvessing and evaluated in air and in mixtures of oxygen and helium at temperatures up to 2400°K and at linear flow rates of 0.1 to 0.2 ft per sec stp. Oxidation characteristics, principally depth of conversion of diboride to dioxide, were determined by a gas analysis method and by postoxidation metallo-graphic analyses. The best oxidation resistance was observed for hafnium diboride-silicon carbide composite which exhibited a 6-mil conversion to dioxide for a 1-hv oxidation in air at 2200°K compared to a 20-mil recession for hafnium diboride with no additive. Analogous improvements in oxidation resistance were observed for the addition of silicon carbide to zirconium. EARLIER investigationof the oxidation behavior of the diborides of the transition elements of Groups IVA and VA in flowing gas mixtures have produced a ranking of these compounds according to which HfB2 is the most oxidation-resistant followed in turn by ZrB2 > TiB2 > TaBz > NbB2. Other ~tudies~-~ have examined the physical, thermal, and thermodynamic properties of these diborides to provide a sound basis for the more detailed and specialized investigations which are required to generate the information needed to assess the usefulness of such materials in high-temperature oxidizing environments. Recent oxidation studies7 have examined the effect of variations of metal and boron content on the oxidation characteristics of zirconium and hafnium diboride in flowing gas mixtures including air and helium plus oxygen. Results obtained in the latter investigation confirmed the superior oxidation resistance of HfB2 over ZrB2. Moreover, metal-rich compositions of hafnium diboride showed improved oxidation resistance over boron-rich compositions at temperatures up to 2000°K; at higher temperatures the differences are not distinguishable. In particular HfBI.7 exhibited a diboride to dioxide conversion depth of 4 mils in 1 hr at 2000°K; HfB2. 2 exhibited a conversion depth of 16 mils for the same exposure.~ Specimens for the study of metal and boron stoichiometry on the oxidation characteristics of HfB2 and ZrB2 were prepared by high-pressure hot pressing, a specialized type of fabrication which produced dense crack-free bodies of the desired compositions with no significant impurity introductions. The purpose of the present investigation was to explore the possibility of further improving the oxidation resistance of the metal-rich ZrB, and HfB2. The plan to accomplish this objective was based in the formulation of several diboride compositions containing other compounds and phases which are generally known to have good oxidation resistance in one or more types of test environment. Ideally, such additives would also enhance or at least not diminish other boride property values principally mechanical strength and those parameters related to thermal stress resistance. The additions selected for HfBz included zirconium, aluminum, and (Ta + TaB2) designed to produce ternary metal diborides, hafnium to form a discrete HfB phase, chromium to provide a metal skeletal phase, (Hf + Si) to form a discrete hafnium silicide phase, and Sic to provide a discrete second phase. Additions to ZrB2 included A1 + B designed to produce a ternary metal diboride, Zr + Si to form a discrete zirconium silicide phase, and Sic to provide a discrete second phase. All the specimens were prepared by high-pressure hot pressing which was used to advantage to fabricate billets of the variety of compositions desired and suitable for oxidation testing. The present investigation also included the evaluation of high-pressure hot-pressed TiB2and TiB2-20 vol pct Sic, conventionally hot-pressed Boride 2,&apos; and KT silicon carbide. Boride

Jan 1, 1969

By R. C. Mahon

The Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. Surface Water Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1946

By Arthur McKee

As HEAT is the controlling factor in all smelting operations, it will be .most helpful to make a new set of calculations on the basis of a .unit of fuel burned at the tuyeres to carbon monoxide. This ties together the only two factors in this operation that seem to be constant with respect to each other-the fuel at the tuyere and the air or its oxygen content. If our usual smelting operations, using natural air heated to reasonably obtainable temperatures, furnish sufficient heat above this critical temperature for the purpose, it is doubtful whether additions of oxygen will be of marked benefit. A unit of fuel will not produce a single heat unit more if burned with pure oxygen than if burned with natural air and less heat will be available per unit of fuel by the amount of heat that is carried in by the preheated nitrogen in the natural air of the blast. This is more readily apparent if considered in connection with a heat balance sheet per unit of fuel at the tuyere. The heat available in the stack, as shown by the committee&apos;s report, is less by reason of the lower fuel consumption per unit of output assumed in this calculation. The balance sheet for enriched air shows a shortage of the amount of heat usually carried in with the blast; also a lack in the hearth of sufficient heat to melt the 18 per cent. additional metal and slag and in the shaft to the extent of the shaft heat required to heat the 18 per cent. additional stock to the melting point. These heat deficiencies are provided for by the largely increased conversion of carbon monoxide into carbon dioxide, which is assumed, as shown by the following figures: Calculation for natural air: Carbon dioxide 18.4 per cent. (after having eliminated the carbon dioxide from limestone) and 20.8 per cent. of carbon monoxide. Calculation for oxygen-enriched air: Carbon dioxide 28.4 per -cent. and carbon monoxide 23.2 per cent. (no carbon dioxide from stone as lime is charged instead).

Jan 11, 1924

By Everett Carpenter

THE average daily production of crude oil-in Kansas a1 the beginning of the year was about 71,000 1 bbl. and, at its close, 82,000 bbl.-an increase of 11,000 bbl. per day. The total production for the state during the year was about 28,250,000 bbl., or an average of practically 77,500 bbl. per day for the year. This increase in the production was the result of the discovery of several new pools of high-grade oil. COWLEY AND SUMNER COUNTIES One of the principal factors in bringing the production of the. state back to its former level was the newly discovered pools in western Cowley County. During December, 1923, the Waite Phillips Co. completed its Johnson No. 1 in Sec. 20, T. 33 S., R. 3 E., which opened up the Rainbow pool about 12 miles southwest of Winfield. In this pool, the production comes from the Burbank sand, locally called the "Rainbow," found at a depth of 3200 ft. The sand varies in thickness from 25 to 40 ft. in the seventeen wells completed during the year, and the initial productions ranged from 300 to 3000 bbl. per day of 40° Be. oil. The Rainbow pool is purely a wildcat discovery, for no. rocks suitable for the use of the geologist are present. To determine the geologic conditions, the larger companies core-drilled the Rainbow area immediately after the discovery. The Marland Refining, Co., drilling on the Graham farm in Sec. 9, T. 33, R. 3, failed to find the Burbank sand and continued to the Siliceous lime, often erroneously called the Wilcox, at 3505 ft., where a well with an initial production of 900 bbl. of 40 Be. oil was obtained. In the development following this discovery, 4 additional wells were completed, 3 of which encountered pay sand at 2500 ft., the initial productions each being about 200 barrels. Judging by the sands already proved and the area indicated as probably oil bearing by the development to date, these pools have a very promising outlook for the future. It is not unlikely that a field second only to El Dorado may have been opened.

Jan 3, 1925

By L. M. Yokum

Tremendous strides have been made in front end loaders in the last 15 years. Fifteen years ago a 21/4-cu-yd front end loader was the largest standard machine you could purchase. Today there are two commercially available 15-yd front end loaders and many 10-yd loaders. The estimated total worldwide market for all front end loaders over 1 cu yd has increased to over 30,000 units yearly. The trend for front end loaders, in general, and for the mining market, in particular, is to larger and larger loaders. Today there are 18 and 24-cu-yd front end loaders in prototype form. It is not inconceivable that within another 15 years there will be front end loaders in the 50-cu-yd class with design features quite different from today&apos;s. These larger loaders are being designed at the demand of the mining industry, and the design criteria are being directed at this market area. The costs of these larger loaders may be greater per unit of capacity, but it is the intent of the various manufacturers that they will be more reliable, be easier to service, give greater availability, live longer, and cost less to maintain, than previous loaders. It is also the intent of the manufacturers to compete directly with the large mining shovel as the front end loaders become appropriately larger and more reliable. There has been some trend in this direction in the past with smaller shovels and loaders. In Table 1 are data for U.S. production of front end loaders (5 to 6-cu-yd class and 10-cu-yd class) and U.S. production of cable-operated, crawler-mounted power shovels, draglines, and cranes (11/z to 5-cu-yd class) for the years 1965 and 1970 (Source: Bureau of Census, U.S. Department of Commerce). Many believe that the decline in shovel production, in particular, is due at least in part to the acceptance of the front end loader as a primary production tool. However, the foregoing comparison is for a smaller shovel class than for front end loaders. It has generally been a rule of thumb that a front end loader is competitive on a cost and production basis with a shovel when it is approximately twice as large as the shovel. This same relationship may not hold true with the larger 10 to 15-cu-yd electric shovels, but at some point, direct competition will probably occur. Current Trends There are many trends today that are significant. One major usage trend in large front end loaders involves load and carry operations. This application is defined as "performing the functions of loading, hauling and dumping with one machine over distances within its economical limits." Many people are using front end loaders to transport material as well as load it. It is estimated that nearly half of all 10-cu-yd front end loaders sold in 1970 went into primary load and carry work. Many times, significant savings result from using the load and carry system, instead of small truck and shovel operations, for distances in excess of 1000 ft. Strip mining in coal utilizes great numbers of front end loaders in this manner. In-pit crushing of limestone is developing on an ever-increasing level, especially in Europe, and this stimulates interest in load and carry operations. In Table 2 is a cost example for 10-cu-yd front end loader in a limestone quarry. More than likely, load and carry use will continue to increase over the next few years. While some types of mining do not lend themselves to load and carry in the pit, such areas as surge piles are applicable and should be studied. In the area of machine operating cost reduction, there

Jan 1, 1974

By Kendall E. Born

Production of crude oil in Tennessee during 1937 was slightly over 37,000 bbl., an 85 per cent increase over the preceding year and the highest since 1928. Closer cooperation between the operators and the State Division of Geology has resulted in more accurate data than have been possible for the past few years. Such cooperation is most desirable, especially in this state, which has no law requiring the filling of drilling permits, logs, and production figures. The increased production for the year has resulted from discoveries of four small pools in the shallow district of Clay and near-by counties. The most promising of these began production late in 1937 and consequently has had little effect on the 1937 total. These discoveries, along with renewed activities in some of the older areas, have increased the production for Clay and adjoining counties from less than 5000 bbl. during 1936 to over 21,000 bbl. in 1937. The Mississippi lime production in Scott and Morgan Counties declined from 16,335 bbl. in 1936 to 14,644 bbl. during 1937. While the decline curve on this production has been gradual, some of the wells are over 20 years old, and it becomes necessary to look for other favorable structures in this general region if increased production is to be obtained or past production maintained. The only natural gas marketed off the lease in Tennessee during 1937 was in Morgan County, where a small amount was furnished for the town of Sunbright and its immediate vicinity. The gas occurs with the oil in the Boone Camp field and small amounts were put on the line from the near-by Coon Hollow and Seabolt pools. Development There were 59 wells spudded in during 1937, of which 18 were drilling or only temporarily shut down on Dec. 31, 1937. Of the 41 completions, 17 produced oil, 5 were gas wells of undetermined quantity, and 19 were dry or near-dry holes. The flush production on the new wells totaled about 1300 bbl. per day. The more important wildcats are listed in

Jan 1, 1938

By A. T. Miesch, L. B. Riley

An error occurred in the preparation of Fig. 3, p. 249, of Basic Statistical Measures Used in Geo-chemical Investigations of Colorado Plateau Uranium Deposits. This figure shows the relation of the arithmetic mean: geometric mean ratio to the geometric deviation. Curves for the cases where n, the number of samples, is 100, 10, and 5 are too high with respect to the ordinate. The error is negligible at low geometric deviations, but becomes increasingly greater wi,th higher values of geometric deviation. Arithmetric mean values in Table I1 are not effected by the errors in Fig. 3. The authors will endeavor to supply copies of the revised curves on request; write to: A. T. Miesch, Geologist, Branch of Radioactive Materials, U.S. Geological Survey, Bldg. 25, Federal Center, Denver 25, Colo.

Jan 1, 1962

By Schrade F. Radtke

The future of lead and zinc, as with any material, will relate directly to their capability to remain competitive; that is, to demonstrate cost-performance ratios that are superior to those of competing materials. These cost-performance ratios are not static; therefore, it is necessary to develop improvements in products or processes to maintain present markets or to penetrate other markets. Perhaps the surest way to achieve these goals, if they can be achieved at all, is through research. The world lead and zinc producing industry established ILZRO as its cooperative research function to carry on both fundamental and applied research and development efforts aimed at the stated objectives. Current research efforts in the fields of die casting, galvanizing, finishing, chemicals, architectural applications, ceramics, and batteries are reviewed and potential impact assessed, some projections are given of possible new areas of research. Environmental research and its impact on future uses of lead and zinc are also discussed.

Jan 1, 1977

By Lawrence Henderson

TO increase tonnage in the early days of coal mining it was necessary only to hire more men. The job now is to increase the tons per man, but other troubles arise because this has been accomplished. With the introduction of continuous miners, newer and faster loading machines, and faster belt conveyors the safety engineer has been faced with new difficulties. Use of larger equipment created roof control problems, which were thoroughly studied by the safety engineers of various companies. With the assistance of the U. S. Bureau of Mines, safety engineers in Alabama conducted roof bolting experiments wherever they appeared to be applicable. Accident records before and after the method was adopted showed results more than justifying the efforts and funds expended. The larger mining companies responded enthusiastically to the program because roof bolting not only prevented accidents but also increased production efficiency, in many cases rep- resenting the margin between profit and loss. In Alabama today there are miles of roof supported by bolts.

Jan 8, 1957

By John Sherbourne

Much valuable scientific research has been performed in recent years on the subject of phase behavior of hydrocarbons. ? 1-11 Engineers employed in petroleum production are interesting themselves in this work as well as in methods of applying the fundamental data available to the solution of their various problems. Recently a number of papers have been published in which applica-tions of phase behavior have been made to specific cases pertaining to critical phenomena.)12-16 Little effort, however, has been made in the literature to show the relation between changes occurring in the critical region and the more common phase behavior, therefore it is believed that a presentation of the fundamentals of phase behavior with reference to hydrocarbons is timely. Study of phase behavior is not new. In the metallurgical field, knowledge of heterogeneous equilibria has advanced tremendously, particularly with reference to solid-solid and solid-liquid behavior. Much is known about vapor-liquid equilibria too, but few engineers are familiar with this subject. ?

Jan 1, 1940