Search Documents

By O. D. Gonzalez, R. A. Oriani

A thermo-osmosis technique has been used to measure the heat of transport, Q* , of hydrogen and of deuterium dissolved in a iron and in nickel, and of hydrogen in Feo.6Nio.4 in the tempevature range 400° to 600°C. For all these systems, Q* is negative and has a large temperature coefficient; an isotope effect can be established for the solutes only in nickel. The magnitude of Q* is considerably larger than the activation energy, E , for migration in the case of these isotopes in a iron, so that all variants of the Wirtz model must be rejected. The phenomenological definition of Q* is developed to show that Q* is related to the mechanisms by which the activation energy is dissipated back into the lattice, and that Q*/E is a function of the ratios of the mean free paths of electrons and of phonons to the distance of jump of the diffusing atom. A correlation is shown to exist between the sign of Q* in thermal diffusion and that of the effective charge in electro migration, and may be understood as due to the large ratio of the mean free path of electrons to that of phonons. THE study of nonisothermal diffusion in the solid state is of interest because certain aspects of the mechanism of diffusion are made manifest which remain concealed though still present in the isothermal case. The thermodynamics of irreversible processes characterizes nonisothermal diffusion, known as thermal diffusion or as the Ludwig-Soret effect, by a quantity, Q*, called the heat of transport, which essentially measures the sign and the magnitude of the steady-state concentration gradient produced by the imposed temperature gradient. The problem then is to understand the quantity Q* at the atomistic level. There does not exist a theory for the atomistic interpretation of the heat of transport. There are, however, two classes of simple models which seem to afford some physical insight into Q*. Wirtz's model1, z and its subsequent generalizations partition the activation energy, E, for the migration of the atom spatially about the region of the migrating atom, so that Q* is the difference between the portion of the activation energy centered about the original site of the jumping atom and that portion about the arrival site. Clearly, the magnitude of Q* cannot on this model be larger than the activation energy for migration. The model of Oriani3 also considers the spatial distribution of E not only before but also after the atomic jump, and Q* is related to the variation of the spatial distribution of E that is produced by the jump. The simplest kind of system with which to compare the consequences of these ideas is the interstitial solid solution, since one may easily choose a temperature at which only the interstitial component moves, the solvent lattice serving as a completely satisfactory frame of reference. Thus, one avoids complications arising when both species in a binary system move. In addition, one avoids the necessity of knowing the energy for the formation of a vacancy, something which is needed for the analysis of thermal-diffusion data on metals which diffuse by the vacancy-exchange mechanism. However, the number of well-measured interstitial systems is extremely small, and, in particular, there are almost no data in the published literature for the temperature dependence of the heat of transport. If one works with solutes which are gases in the pure state at ordinary temperatures, one may use the technique of thermo-osmosis4 which permits thermal diffusion to be measured over a small temperature difference so that the temperature dependence of Q* can be more easily determined. The choice of dissolved hydrogen in iron and nickel was based on these considerations as well as on the desire to look for an isotope effect associated with localized

Jan 1, 1965

By P. E. Arnold, G. S. Ansell

RELAXATION in metals has been studied in detail by many workers in recent years.1-5 These studies have shown that there is an energy-loss peak observed in a metal placed in mechanical resonance at low frequencies which may be correlated with various metallurgical processes. These experiments have been largely used to study single-phase materials. In order to study the effect of a finely dispersed second phase in a metal matrix upon this phenomenon, the relaxation behavior of an aluminum-aluminum oxide SAP-Type alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions was investigated by the use of internal-friction measurements. The alloys studied, designated MD 2100, consist of a matrix of commercial-purity aluminum containing a finely dispersed second phase of aluminum oxide. The aluminum oxide is present in this alloy in the form of fine platelets approximately 130A units thick and several microns on edge. The mean free path betwen dispersed platelets is approximately 0.5 p. The grain size of this alloy is extremely stable at temperatures as high as the melting temperature of the aluminum matrix. In the as-extruded condition the grain diameter is several microns, while in the recrystallized condition it is several millimeters in diameter. The damping characteristics of the alloy samples were determined using a torsional-pendulum device. The internal-friction constant was determined for this alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions over the temperature range from 343" to 923°K at frequencies of 0.9, 1.3, and 1.8 cycles per sec. An internal-friction peak was observed in testing the fine-grained alloys which was not observed for the coarse-grained alloys. This peak, which might be associated with a type of grain-boundary relaxation, was observed at each of the three different test frequencies for the fine-grained sample. The temperature at which the relaxation peak occurred for each of the three different frequencies is shown in Table I. From these data an activation energy of relaxation for each pair of frequencies was determined by comparing the temperature shift of the relaxation peak with frequency between each of the test frequencies, assuming that an Arrhenius-type rate equation is applicable. The activation energy of relaxation determined from these data is also shown in Table I. The mean value of the activation energy was about 6 kcal per mole. The activation energy for the relaxation process determined in this investigation indicates that the relaxation associated with the grain boundaries in this aluminum-aluminum oxide SAP-Type alloy is quite a different process than grain boundary relaxation in single-phase aluminum alloys. In these latter alloys, the activation energy for relaxation has been found to be the activation energy for self-diffusion, approximately 36 kcal per mole1,2 Where the activation energy is the same as the activation energy for self diffusion, it has been proposed that the relaxation phenomena is dependent upon vacancy formation and motion. It is apparent therefore, that, in this aluminum-aluminum oxide SAP-Type alloy, the relaxation must be due to another type of atom transport. It has been shown previously in studies of the high-temperature, low-stress, steady-state creep behavior of as-extruded aluminum SAP-Type alloys, that the activation energy for steady-state creep is one that may be characterized by the nucleation of dislocations from the grain boundaries. It is proposed that the relaxation behavior observed here is due to a similar effect. In this case, the internal-friction peak is a resonance behavior due to the time-dependent nucleation of dislocations from grain boundaries in the sample. A process of this type would have an activation energy which is undoubtedly stress-dependent and of the form Q = Q, + (dQ/du)u

Jan 1, 1962

By D. de Fontaine

A convolution procedure is described for obtaining an analytical expression for the composition profiles of solute concentration:; in binary solid solutions. The free energy of solutions containing such compositional inhomogeneities can then be evaluated and the stability of spherically symmetric clusters (G.P. zones, for short) us a function of their radii and central compositions can be studied accordingly. Two characteristic zone radii are defined: the minimum radius (RM) corresponding to the smallest zone for which growth is energetically favored over dissolution, and the critical radius RK) corresponding to zones associated with the minimum work of formation. The values of RM and RK coincide at the two classical limits of nucleation and growth and spinodal decomposition. As the spinodal is approached, however, RM and RK diverge increasingly and it is proposed that the initial] decomposition morphology is governed more closely by the minimum, rather than by the critical radius since the former possesses no singularity within the m eta stable phase boundary. Reversion is briefly discussed in the light of the foregoing and it is shown that a set of reversion temperatures located between the coherent miscibility gap and the coherent spinodal must correspond to a given distribution of low temperature zones. SINCE the early works of Guinier1 and preston,2 the kinetics and morphology of GP zones have been studied extensively, see Ref. 3, for example, for a recent review. Nevertheless, a completely satisfying theoretical treatment of the decomposition of meta-stable or unstable binary solid solutions is still lacking due to the almost unsurmountable mathematical difficulties that one encounters in attempting to solve the pertinent diffusion equation which, in principle, describes the whole process. This equation, first derived by Cahn for the initial stages of spinodal decomposition,4 is a nonlinear partial differential equation of the fourth order in anisotropic space, a general analytical solution of which is completely out of the question. From this equation, some prediction can be made, however, concerning the later stages of spinodal decomposition5 and a recent numerical solution6 of the equation in the case of one- and two-dimensional composition modulations of a solid solution inside the spinodal has led to the following considerations: the sinusoidal morphology7 is to be expected only for solutions of average composition c, located near the center of the coherent miscibility gap.8 For solutions with co closer to the spinodal decomposition, depleted shell zones9 should constitute the first recognizable decomposition product, later evolving to iso- lated, enriched preprecipitates in a uniformly depleted matrix as this must, in all cases, constitute the final metastable morphology, barring, of course, loss of coherency and change in crystal structure. In agreement with the qualitative description of Bonfiglioli and Guinier,l0 it thus appears that the various models discussed by previous authors are, in fact, idealized successive stages of the general decomposition process. Unfortunately, corresponding calculations for a solid solution outside the spinodal are not yet available because of two additional difficulties: it is essential that the diffusion equation be solved in three-dimensional space, and furthermore, one must include in the equation an appropriate "source term" describing the statistics of the creation of composition fluctuations required to trigger the nucleation events. At present, a general treatment of this problem does not appear to be tractable. Nevertheless, by using a modelistic approach, i.e., by selecting a priori certain composition variation profiles and by evaluating their associated free energies, one can draw certain conclusions relative to the stability of these isolated composition modulations or "zones", both outside and inside the spinodal. This is the object of the present investigation. THEORY We shall now describe a standard four-parameter spherically symmetric GP zone, evaluate its free energy according to the Cahn and Hilliard11 formula (Eq. [5], below), and plot the corresponding energy surfaces as a function of zone amplitude and radius as

Jan 1, 1970

By Donald Jaffe, Michael B. Bever

The solidification of Al-Zn alloys (2 to 70 pct Zn was investigated at different rates of solidification. The resulting structures were studied; the amounts of nonequilibrium eutectic were measured and compared with the amounts calculated on the assumption of no diffusion in the solid. The compositions of the cored primary constituent were investigated by quantitative autoradiography after activation of the zinc by neutron irradiation. These compositions were also determined from microhardness values. IN a recent investigation of the soltdification of aluminum-rich AI-Cu alloys,' the amounts of non-equilibrium eutectic were measured and compared with the amounts calculated on the assumption of no diffusion in the solid. The compositions of the cored primary constituent were investigated by quantitative autoradiography. The work reported here extends the investigation of nonequilibrium solidification to the Al-Zn system in the range from 2 to 70 pct Zn. In addition to autoradiography, microhard-ness values were used to determine compositions on a micro scale. Solidification Experiments The alloys contained approximately 2. 6, 12, 20, 30, 50, and 70 wt pct Zn and the balance aluminum. According to published diagrams the eutectic reaction occurs at 382°C between the eutectic liquid (95 pct Zn), a (82.8 pet Zn), and $ 498.9 pct Zn). Solid-state reactions at lower temperatures (due to the miscibility gap between 350" and 275"C, the eutectoid at 275'C, and the precipitation from supcrsaturated a) did not affect this investigation. Even if they occurred to any appreciable extent, they did not alter the evidence pertaining to the solidification structures. The alloys had to be of high purity to avoid radioact~ve contamination during activation. The aluminum analyzed 0.015 pct Si, 0.009 pct Fe, less than 0.004 pct Cu, and less than 0.006 pct Mg with traces of sodium and titanium; the zinc was reported to be at least 99.99 pct pure with traces of iron and magnesium. The alloys were prepared under argon in an induction-heated, bottom-pouring furnace, and poured into a coated steel mold, which could be preheated to temperatures up to 700°C in order to control the rate of solidification. The pouring temperatures ranged from about 40" above the liquidus for 2 pct Zn alloys to about 130°C above the liquidus for 70 pct Zn alloys. As soon as the melt entered the mold, the readings of a thermocouple placed % in. above the bottom of the mold were recorded by a recording potentiometer. Cooling at the rate induced by the initial temperature of the mold was continued to a temperature 100°C below the liquidus; the mold with its contents was then quenched in icy brine. Quenching from a fixed interval below the liquidus was used to provide a standardized procedure, since the solidus and liquidus temperatures and the interval between them vary greatly over the composition range investigated. The temperatures from which the samples were quenched were below the equilibrium solidus, but under nonequilibrium conditions some liquid was still present. This residual liquid solidified during the quench. The samples measured 314 in. diam and 11, in. height. Drillings for chemical analysis were taken

Jan 1, 1957

T. A. Rickard, Denver, Colorado: The observations made by the author concerning the treatment of gold-bearing ores, deal with the subject only briefly and in a general way; but, coming from an authority, they invite comment. In stating the fact that a " finely-divided condition " is a necessary characteristic of ores containing free gold, the author must be refer ring to those mining districts only with which he himself is ac quainted. The statement would not be true of certain gold-mining regions in America and Australia. The ores of some Californian mines and the mill-stuff treated at certain of the mills of Clunes and Ballarat in Australia, and of Otago in New Zealand, contain the gold in a free but in a coarse state. Moreover, "reduction to fine sand and flour" is not required by certain ores, even though the gold be in a finely-divided condition. In such cases the gold becomes de tached from the quartz before the gangue has been pulverized into particles as small as those in which the gold occurs. The dry-crushing of free-milling gold-ores is onknown in the new mining regions of the world. It is not clear whether the author has in mind any European district in which such a process is in actual use. If he has, a description of the method and the results obtained would be very valuable. Dry-crushing is, other things being equal, twice as slow and twice as expensive as wet-crushing. In the case of free-milling gold-quartz it serves no purpose, since such ore does not carry sulphides which contain any large percentage of value, and which, by being slimed, may carry away part of that value. The dry-crushing of a free-milling gold-quartz would be considered an absurdity by an American metallurgist. If the ore contain "free gold only," why submit it to a further treatment, such as concentration, after its passage over the amalga mating-plate ? What does the author propose to concentrate ? Again, why anticipate the treatment of tailings by the McArthur Forrest, or some other process ? The satisfaction felt by a mill-man in saving gold by a subsequent treatment of the tailings from his mill appears to me to be like that of the man who shoots at a rabbit,

Jan 1, 1894

By B. Post, D. Moskowitz, F. W. Glaser

Lattice parameters of various hafnium compounds, two borides, a carbide and a nitride were determined. Some physical properties were measured and comparisons with the properties of the corre-sponing zirconium compounds were drawn. A LTHOUGH borides of transition metals have A been extensively investigated in recent years, there are few references in the literature to borides of hafnium. This is not surprising, in view of the extreme scarcity and great cost of the purified metal. Becker' reported the existence of a boride, carbide, and nitride of hafnium; he listed the formulas as HfB, HfC, and HfN. However, in his work no mention was made of chemical analyses of the reaction products. In this paper results of a study of various hafnium compounds, including borides, carbides, and nitrides, are reported. It was expected, of course, that these compounds would closely resemble their zirconium analogues, which have previously been extensively investigated. Three borides of zirconium are known: ZrB,² ZrB,² and ZrB212.4 In addition, one carbide, ZrC,5 and one nitride, ZrN,5 have been reported. It should be noted that ZrB and ZrB12 are stable phases only in relatively high-temperature regions, unlike ZrB2, which is stable from room temperature to its melting point." It was felt that hafnium would yield corresponding borides, carbides, and nitrides with similar stability ranges. Experimental Procedures and Results A quantity of hafnium metal that was better than 97 pct pure, with zirconium as its major impurity, was furnished by the Argonne National Laboratories. The boron powder used was approximately 96.5 pct pure. In general, the procedure involved mixing the metal and boron powders in the desired proportions, and subsequently hot pressing them. The resulting specimens were analyzed chemically and phases present were identified by X-ray diffraction methods. A Philips Norelco Geiger counter spectrometer was used for identification of components and for measurement of lattice constants. Filtered copper radiation was used for all X-ray work. Electrical resistivity and density measurements were carried out at room temperature. The stable diboride, HfB2, will be described first. Stoichiometric quantities of boron and metal were heated to approximately 2000°C during hot pressing. The reaction product was shown by X-ray diffraction methods to be isomorphous with ZrB2 (space group Dlgh; P6/mm). Values of lattice constants of HfB2 compared with those of ZrB2 are shown in Table I. The calculated density of HfB2 is 11.2 g per cc, compared with a measured (pycnometric) value of 10.5 g per cc. HfB2 specimens prepared under a wide variety of conditions (including variations in initial Hf-B ratios) showed only insignificant variations in lattice constants, indicating a very narrow range of homogeneity. Like ZrB2,7 HfB2 is an excellent electrical conductor. The resistivity at room temperature of hot-pressed samples, approximately 85 pct dense, is 12 microhm-cm. This compares favorably with the electrical resistivity of 10 mi-

Jan 1, 1954

By R. W. Heckel, R. A. Tanzilli

Treatment of the finite, diffusion-controlled, two-phase, moving-interface homogenization problem has been carried out by numerical methods for a wide range of input parameters. Solutions have been obtained for planar, cylindrical, and spherical diffusion geometries. The effects of parameters such as the interdiffusion coefficients (concentration-independent) of- both phases, the concentrations (time-independent) of each phase at the interlace, mean composition, initial size of the dissolving- phase, and initial composition of- the two phases are considered. The results are displayed to show both the position of the interjace and the degree of homogenization (expressed in terms of concentration at the matrix phase symmetry boundary) as a function of diffusion time. Typical exaw~ples to which the results may be applied are discussed. A limited number of exact, closed-form solutions to the multiphase, diffusion-controlled, moving-interface problem exists in the literature, e.g., Refs. 1 to 7. The exact, closed-form solutions generally consider the outermost phases to be infinite in extent and also assume an interfacial velocity function. It is through use of such boundary conditions that closed-form solutions are readily obtained. An extensive literature also exists on numerical solutions to the mathematically analogous solidification problem, e.g., Refs. 8 to 12. In addition, a numerical solution involving mass transfer with spherical interfaces and infinite boundaries has recently been carried out.13 A practically important class of diffusion problems exists, however, in which the boundaries of each phase away from the interface are finite. For example the finite boundary condition arises when one sets up a model for analyzing the homogenization behavior of two-component powder compacts in two-phase systems or for studying the solution behavior of precipitates. Although exact, closed-form solutions have as yet not been found to this class of problems, solutions are possible using numerical methods. The purpose of this paper is twofold: 1) to describe a numerical method for treating the two-phase, diffusion-controlled, moving-interface problem involving finite boundaries with planar, cylindrical, and spherical interfaces; 2) to present the results of a parametric study which identifies the role played by each variable appearing in the analytical model. R. A. TANZlLLI,Student MemberAIME,onleaveofabsence from the General Electric Co., Re-entry Systems Department and A. W. HECKEL, Member AIME, are Graduate Student in Materials Engineering, and Professor, Department of Metallurgical Engineering, respectively, Drexel Institute of Technology, Philadelphia, Pa. Manuscript submitted May 6. 1968. IMD MATHEMATICAL MODEL The three geometries analyzed are shown in Fig. 1. For each configuration a symmetry element is shown, across whose boundaries the mass transfer is zero. Mean composition, C, and the characteristic solute-rich phase half-thickness (or radius), 1/2, are the independent variables while the characteristic symmetry element half-thickness, L/2 (measured from solute-rich phase center to the matrix phase plane of zero mass transfer), is a dependent variable. The symmetry element for a planar interface accurately represents a real diffusion situation involving the stacking of symmetry elements of constant size. Because cylindrical and spherical symmetry elements of constant size cannot be stacked to fill space, the meaning of the dimension, L/2, for these situations may be considered in terms of the following approximations: and where NA is the number of parallel cylindrical elements per unit area on a surface normal to the cylinder axes and Nv is the number of spherical elements per unit volume. The model consists of a solute-rich phase matrix phase composite of limited mutual solubility. The concentrations at the interface are assumed constant with time; no assumption of local equilibrium at the interface is necessary except for the case where the

Jan 1, 1969

By M. J. Hordon

Measurements of the 103 yield stress of ordered and disordered poly crystalline Cu ,Au were related to the ordered antiphase domain size determined by resistivity measurements. For undeformed material, a yield stress maximum wa obtained at a critical domain diameter of about 40A. Plastic deformation resulted in a marked increase in the yield stress and electrical resistivity of the ordered alloy compared to the disordered, the strain hardening rate increasing regularly with initial antiphase domain size. Order hardening was accompanied by a sharp reduction in size of the initially large domains. It has been observed that the yield stress of ordered and partially ordered Cu3Au alloy varies sensitively with antiphase domain size aid degree of order.ly2 In addition, ordering of the lattice leads to a marked increase in the strain hardening rate (order hardening) as compared to the rate for the disordered alloy. In the present investigation, changes in the electrical resistivity and yield stress of ordered polycrystalline Cudu with varying initial domain diameters were measured after tensile plastic deformation in order to examine the effect of cold work on the antiphase domain size. EXPERIMENTAL PROCEDURE Au-Cu alloy of 99.99 pct purity analyzing 50.85 wt pct Au-balance copper was obtained from the Handy-Harmon Co., N. Y., in the form of 0.061 in. diam drawn wire. Wire specimens 3 in. in length were given the following annealing treatment in nitrogen: 500" for 72 hr, 820" for 15 hr, and 450" for 5 hr, followed by a water quench. The annealing sequence resulted in a completely disordered structure with a grain size of about 0.2 mm. The disordered specimens were then reannealed at 360' in nitrogen for periods varying from 10 min to 150 hr followed by quenching to produce ordered structures with varying domain sizes. The degree of ordering and variation of domain size was followed by electrical resistivity measurements made at room temperature using a low resistance precision Kelvin double bridge apparatus. The specimen resistance was determined over a length of 4.0 cm between two brass knife-edge contacts while the specimen was immersed in an oil bath to minimize temperature variations. In addition, the current flow in the circuit was minimized by a current pulse technique in balancing the bridge in order to avoid heating the specimen. Using a sensitive galvanometer to detect the bridge null, the accuracy of the resistance measurement Wire specimens were plastically strained in tension with an Instron tensile unit at strain rates in the range 5 x 10"5 sec-' to 2 x 10"4 sec-'. Stress and extension data were fed into the Instron chart drive amplifier to obtain the actual stress-elongation curve from which the yield stress at 10"3 strain was determined. The maximum resolution of the apparatus was approximately 50 psi stress and 3 x 104 strain. At various plastic strain levels, deformation was interrupted and the electrical resistivity determined after removing the stress. RESULTS AND DISCUSSION 1) Yield Strength of Ordered Cudu. In order to determine the effect of the ordered antiphase domains on the initial yield stress, specimens were prepared with varying domain sizes ranging from zero for 5 completely disordered structure to about lo5A for a completely ordered structure by suitable annealing treatment. Domain sizes were estimated by comparing room temperature electrical resistivity data with the original data of Jones and sykes3 as modified by rdle.' In agreement with previous work, the resistivity varied sensitively with domain diameter and degree of order, decreasing from approximately 11.6 x l0- ohm-cm for the disordered structure to about 5.9 x l0- ohm-cm for ordered domains above 10"3 cm in diameter. Fig. 1 shows the change of the 103 yield stress with ordered domain size. It is evident that the maximum

Jan 1, 1963

By P. M. Kelly, E. P. Butler

The stability of a 70/30 Mn-Cu alloy aged to peak damping has been investigated using electron microscopy, X-ray diffraction, and torsional pendulum measurements. Storage at room temperature or at 100" C causes a reduction in damping capacity. This is shown to be due to the formation of subdomains which "lock" the main domain structure and so hinder their movement. After storage the damping capacity can be restored by a retransformation treatment, which generates structures identical to those found in newly aged specimens. Plastic deformation by rolling also causes a decrease in damping capacity. In this case the damping capacity can only be restored by retransformation if the amount of deformation is less than about 5 pct. THE general metallography and structure of these high damping capacity alloys has been discussed in Part I of this work.1 Part II deals with some of the variables that affect the damping capacity. In particular, the stability of the damping capacity of a 70/30 alloy aged for 2 hr at 425° C and quenched has been investigated. The temperature sensitivity of the damping capacity of a 70/30 alloy aged for 2 hr at 450° C has been reported by Birchon.2 The damping capacity begins to decrease with increasing temperature, and is very low above the M, temperature of 125°C. The cubic — tetragonal transformation is completely reversible and there is no apparent thermal hysteresis associated with the change in damping capacity. Another important effect was first reported by Dean and his coworkers.3 They noticed a decrease in the damping capacity with time for specimens of a quenched tetragonal alloy. More recently workers at the Admiralty Materials Laboratory 4 have studied the stability of an aged 70/30 alloy. They found that the damping capacity decreased to half its original value after about 1000 hr at room temperature. EXPERIMENTAL The techniques used for electron microscopy and X-ray diffraction have been described in Part I. The damping capacity was measured by means of a torsional pendulum, using rectangular specimens, 3 by 0.3 mm with a 6 cm gage length. The specific damping capacity, S.D.C., was calculated as a percent amplitude decay in free vibrations over 10 cycles, starting at an amplitude which corresponded to a 700 psi surface shear stress. Because of the stress dependence of the damping,' the values obtained were about a third those reported for a 5000 psi surface shear stress.' RESULTS a) Effect of Aging Temperature. The effect of aging temperature on the damping capacity is shown in Fig. 1. The damping capacity reaches a peak of 12 pct after aging at 400° to 425°C) then begins to decrease as the volume fraction of a Mn increases. At higher aging temperatures the structure becomes cubic again with a low damping capacity. b) Stability of the Aged Structure. The damping capacity of the aged alloy decreases with time at room temperature. This process could be accelerated by storing at 100°C, when about 100 hr were required for the damping to fall to half its original value. The results of room temperature and 100°C storage, for times up to 1000 hr, are shown in Fig. 2. The damping capacity starts to decrease after about 24 hr at 18° C and 1 to 2 hr at 100°C. It was found, however, that the damping could be almost completely restored by retransformation. The specimens were held at a temperature above the M, for a short time, 250° C for 5 min, and then quenched. The values of damping capacity for specimens that were aged, stored, and then retransformed are shown by the full points in Fig. 2. X-ray measurements of the c/a ratio and hardness readings on the specimens did

Jan 1, 1969

By A. Vignes, J. P. Sabatier

A study of ternary diffusion at 1315°C in the Fe-Co-Ni system covering the entire ternary phase diagram has been carried out. Experimental values of the four interdiffusion coefficients DFeNico,DFeCoCo, DFeCoNi were computed at 33 points of the ternary diagram. The limiting values of these coefficients on the three sides of the ternary diizgram have also been determined. This set of data is presented as a contour map on the ternary isotherm for each of the four coefficients. Assuming that the Fe-Co-Ni system can be considered as ideal, the phenomenological coefficients Lk ij (with k = Fe) have been computed and the Onsager reciprocal relutions verified. It is shown that, in the Fe-Co-Ni system, the diffusion process can also be described by only two interdiffusion coefficients DFeFe and DCoNiFe, the second cross diffusion coefficient DCoFeNi being equal to zero and the second direct difusion coefficient being given by The values of the cross interdiffusion coefficients and of the Onsager coefficients are explained in terms of atomic mobilities of the three components with the help of a kinetic calculation due to Lane and Kirkaldy.8 It is shown that all the results are explained if the tracer difusion coefficients of the three components are such that DFe > DNi ~ DCo in complete agreement with experimental data on the three binary systems. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. In binary diffusion, there is just one independent composition variable and only one coefficient Dij is needed to describe the interdiffusion process. In ternary diffusion, we must allow for cross interaction between two independent species, and four interdiffusion coefficients are necessary to describe the transport process. Kirkaldy et al.1,2 have determined interdiffusion coefficients in the systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy4 have reported intrinsic diffusion coefficients for the r phase at 1300°C of Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.3 Interdiffusion coefficients were measured at three different compositions at 850°C in the single phase copper-rich corner of the Cu-Zn-Mn system by Dayananda and race.5 Zie-bold and Ogilvie6 have determined interdiffusion coefficients in the single-phase field of the Cu-Ag-Au system at 725°C. Preliminary results on diffusion at 1136°C in the system Fe-Co-Ni have been reported.7 In this study, data are reported on a more complete determination of interdiffusion coefficients in the Fe-Co-Ni system in the entire ternary at 1315°C. There is complete solid solubility with the fcc structures at 1315ºC, and this system can be considered as nearly ideal. This approximation allows the computation of the Onsager phenomenological coefficients. These values can then be used to test a kinetic calculation of the Onsager L coefficients in ternary substitutional solid solutions due to Lane and Kirkaldy.8

Jan 1, 1970

By W. C. Hagel, J. H. Westbrook

THERE has been a recent revival of interest in the intermetallic compound AgMg as an experimental material for study of the physical and chemical properties of simple ordered structures. Studies of mechanical behaviors,1-4 diffusion,5,6 and thermo-dynamic properties7'8 have been reported. In several of these studies, heat treatments have been carried out in argon-filled silica capsules at temperatures as high as 750°C with no apparent adverse effects. The present authors were, therefore, startled to discover in the course of some yet unpublished work, that gross melting of near-stoichio-metric AgMg compositions occurred in such samples more than 100 deg below their melting point of about 800°C. This note is to report a brief series of experiments carried out to establish the reason for this behavior. Gross errors in sample composition and failure of furnace temperature controls were quickly eliminated as causes of melting. The first tangible lead came from chemical analysis of an AgMg sample which had melted during treatment at 750°C. A silicon content of 3.3 wt pct was found. Since satisfactory analyses had been obtained on the original as-cast ingot, contamination by diffusion and/or reaction with the fused silica capsule seemed a distinct possibility. A perplexing fact, however, was the apparently capricious incidence of the effect. Not only was it previously unknown, even in the experience of the present authors; but, in the early part of the present study, melting sometimes occurred and sometimes not with specimens treated under constant conditions. Indeed, one sample successfully survived a 750°C heat treatment and yet melted completely during the course of a subsequent anneal in an identical capsule at a lower temperature. To obtain evidence that silicon contamination could lower the melting point to the extent observed, the following experiment was performed. A series of ternary alloys was made up with a stoichiometric AgMg base and containing 0.1, 0.2, 0.4, 1, 2, and 4 wt pct Si. Melting was done in MgO crucibles under a cover of argon gas. After holding 10 to 20 min in the temperature range 850° to 900°C, the alloys were allowed to solidify in the crucible and the temperature during cooling automatically recorded with a Pt/Pt-10 Rh thermocouple. Results from the cooling curves are shown in Fig. 1. Checks within 2 to 5C° were obtained upon repeated melting, cooling, and freezing. The whole series of cooling curves as well as metallographic examination of the melted alloys established that the AgMg rich portion of the AgMg-Si quasibinary is an eutectic-type system. The melting point of AgMg is lowered from approximately 820°C in the pure stoichiometric binary9 to about 710°C in the saturated intermetallic phase. Since second phase was observed in all samples on cooling to room temperature, the solid solubility of AgMg for silicon evidently falls rapidly with decreasing temperature as indicated schematically by the dashed solvus in Fig. 1. It is thus established that a silicon content

Jan 1, 1963

By R. M. Brick, J. T. Richards

Tests have been conducted to determine the mechanical properties of several beryllium copper alloys down to liquid air temperatures. The materials investigated include beryllium copper, beryl-lium-cobalt-copper, and beryllium-zinc-copper in the wrought and cast conditions. As a means of evaluation, the influence of cold work and age hardening treatment upon subzero behavior has been observed. The effects of temperature upon both elastic and plastic deformation are also considered. THE low temperature mechanical properties of beryllium copper are of current interest in view of the increasing number of subzero applications. At extremely low temperatures, beryllium copper components are employed in temperature control and gas liquefaction equipment. At more moderate temperatures, such as those encountered in arctic regions, these alloys find use in a wide range of civilian and military applications. Although several previous subzero investigations have included beryllium copper,'-' none have been complete with respect to test temperatures or materials employed. As indicated in Table I, the alloy: used by Colbeck and MacGillivray,1 Walle,2 and Kostenets' were nonstandard and were not representative of present commercial practice. In addition, Kostenets4 did not test age hardened specimens, while the temperature in the other investigations", "-' were not carried below —100°F. These tests, however, indicate that beryllium copper offers interesting possibilities in subzero atmospheres, since the increase in strength with decreasing temperature is not accompanied by a reduction in ductility or impact resistance. As a means of checking and extending this earlier work at subzero temperatures, an investigation was undertaken at the University of Pennsylvania. In addition to testing the standard 2 pct beryllium copper, other alloys were also considered in wrought and cast forms. Charpy impact and tension tests were included with particular emphasis on the elastic characteristics, since beryllium copper is frequently selected for its spring qualities. Nominal test temperatures were +80°, —75", —200°, and —300°F. Test Materials Wrought beryllium copper, beryllium-cobalt-copper, and beryllium-zinc-copper specimens were machined from 0.560 in. diameter rod. These alloys were tested in the solution treated, cold drawn, or age hardened conditions. In the case of solution treated beryllium copper, some specimens were aged (3 hr at 600°F) for maximum hardness and others were overaged (1 1/2 hr at 750°F) to determine the effect of heat treatment. The compositions and average room temperature properties of these wrought alloys are presented in Table 11. The casting alloy versions of beryllium copper and beryllium-cobalt-copper were prepared as sand-cast cylinders, roughly 3/4 in. diameter x 6 in. long. Test specimens were machined from these cylinders. Conditions tested included as cast as well as solution treated and age hardened. Table 111 lists compositional and room temperature property data for the cast alloys. Test Methods Tension tests were conducted on specimens having a 0.25 in. diameter reduced section over a 1 in. gage length. To insure axiality, specimens were loaded by means of hardened chains. The yield strength at 0.2 pct offset was obtained from autographically recorded stress-strain curves resulting from a spe-

Jan 1, 1955

By W. C. Ellis, E. S. Greiner

Metallic titanium has been prepared in small quantities since the beginning of the century. Hunter1 reported in 1910 that he obtained a malleable product of 99.9 pct purity by the reduction of the tetrachloride by sodium in a closed container. Later Van Arke12 and Fast prepared small quantities of malleable titanium by thermal decomposition of titanium iodide. Another method for producing malleable titanium from tetrachloride was reported by Kr0ll4 who used magnesium as the reducing agent. More recently Dean, Long, Wartman, and Anderson5 working at the U.S. Bureau of Mines have reported the preparation of the metal on a pilot plant scale by the reduction of titanium tetrachloride by magnesium in an atmosphere of helium. Their product, which is malleable, was used in the present investigation. Early in 1948 after the work of this paper was completed Campbell, Jaffee, Blocher, Gurland, and Gonser6 described the strength and working characteristics of pure titanium which was prepared by the iodide method on a scale producing 300 to 600 g per run, in the form of 0.3- to 0.4-in. diam rods. Their product is characterized by low hardness and large capacity for cold work which they attribute to a high degree of purity with respect to oxygen, nitrogen, and carbon. Titanium has a melting point of about 1725 C," it may be classed as a light metal since the specific gravity is 4.5 g per cc-I. The crystal structure is close-packed hexagonal from room temperature to 885°C. Above this temperature the structure is reported7 as body-centered cubic. The change in crystal structure has been associated with discontinuities in specific heat,8 electric resistanceg and theimoelec-tric force10 at temperatures near 890°C. It is reportedll that annealed titanium has a tensile strength of 78,700 psi which can be increased by cold-work to 123,000 psi. In the present investigation, the lattice constants at room temperature, the thermal expansivity between 30 and 800°C, as well as the electrical resistivity and thermoelectric force against platinum between — zoo and I000 C have been determined. Materials For the measurements, two series of specimens were prepared from titanium furnished by the U. S. Bureau of Mines. The first was made from an annealed sintered compact, 0.38 in. thick. Sections of the compact were cold-swaged with intermediate anneals in vacuum to the sizes used. Sizes over 0.25-in. diam were annealed at I000°C and smaller sizes at 800°C. Specimens originating from the sintered compact are designated in this paper as A. The second series of specimens was made from a rod of titanium, 0.19 in. in diam, which was cold-swaged with the necessary intermediate anneals to the required sizes. This series of specimens is designated B. The impurities in the specimens of titanium, determined by chemical analysis, are given in Table 1. Oxygen and nitrogen which Were not determined by analysis, are probably present although in small quantities in view of the ductility of the material.

Jan 1, 1949

By W. C. Ellis, E. S. Greiner

METALLIC titanium has been prepared in small quantities since the beginning of the century. Hunter1 reported in 1910 that he obtained a malleable product of 99.9 pct purity by the reduction of the tetrachloride by sodium in a closed container. Later Van Arkel2 and Fast3 prepared small quantities of malleable titanium by thermal decomposition of titanium iodide. Another method for producing malleable titanium from tetrachloride was reported by Kroll4 who used magnesium as the reducing agent. More recently Dean, Long, Wartman, and Anderson5 working at the U.S. Bureau of Mines have reported the preparation of the metal on a pilot plant scale by the reduction of titanium tetrachloride by magnesium in an atmosphere of helium. Their product, which is malleable, was used in the present investigation. Early in 1948 after the work of this paper: was completed Campbell, Jaffee, Blocher, Gurland, and Gonser6 described the strength and working characteristics of pure titanium which was prepared by the iodide method on a scale producing 300 to 600 g per run, in the form of 0.3- to 0.4-in. diam rods. Their product is characterized by low hardness and large capacity for cold work which they attribute to a high degree of purity with respect to oxygen, nitrogen, and carbon. Titanium has a melting point of about 1725°C5 it may be classed as a light metal since the specific gravity is 4.5 g per cc-1. The crystal structure is close-packed hexagonal from room temperature t0 885°C. Above this temperature the structure is reported7 as body-centered cubic. The change in crystal structure has been associated with discontinuities in specific heat8 electric resistance9 and thermoelectric force10 at temperatures near 890°C. It is reported11 that annealed titanium has a tensile strength 0f 78,700 psi which can be increased by cold-work to 123,000 psi. In the present investigation, the lattice constants at room temperature, the thermal expansivity between 30 and 800°C, as well as the electrical resistivity and thermoelectric force against platinum between - 200 and 1000°C have been determined. MATERIALS For the measurements, two series of specimens were prepared from titanium furnished by the U. S. Bureau of Mines. The first was lade from an annealed sintered compact, 0.38 in. thick. Sections of the compact were cold-swaged with intermediate anneals in vacuum to the sizes used. Sizes over 0.25-in. diam were annealed at 1000°C and smaller sizes at 800°C. Specimens originating from the sintered compact are designated in this paper as A. The second series of specimens was lade from a rod of titanium, 0.19 in. in dial, which was cold-swaged with the necessary intermediate anneals to the required sizes. This series of specimens is designated B. The impurities in the specimens of titanium, determined by chemical analysis, are given in Table I. Oxygen and nitrogen which were not determined by analysis, are probably present although in small quantities in view of the ductility of the material.

Jan 1, 1948

By E. T. Turkdogan

This is a compilation and a critical review of the data on the Fe-Ca-0 ternary system. Using the results on the reductiorz-equilibria, an oxygen potential diagram is drawn for the greater part of the system. A number of univariant systems and invariant points, not determined experimentally, are evaluated by making use of the theorem on univariant curves intersecting at an invariant point. The formation of solid solutions and ternary compounds and the crystal structures of some of the phases in the composition-diagram are given for a feu! temperatures. DURING the past thirty years there has been a continued interest in the study of the Fe-Ca-0 system. A detailed literature survey made by white1 in 1943 indicated that further work was required to clarify the phase relationships; in fact, the work carried out in the subsequent years, reviewed by Burdese2 in 1954, made a valuable contribution to a better understanding of this subject. Most of the data were obtained by the step-wise reduction of mixtures of iron oxides and calcium ferrites. However, there is some uncertainty about the phase relationships in this system, arising mainly from insufficient use of thermodynamic concepts in the construction of phase diagrams. In this paper an attempt is made to establish the invariant points from the available data. OXYGEN POTENTIAL DIAGRAM Schenck and coworkers3,4 were the early investigators who studied part of this system by the step- wise reduction method and suggested the formation of two ternary compounds, CaO.FeO.Fe2O3 and 2Ca0.5Fe0.2Fez03, the latter being referred to as point X. They also deduced from their results that the phases Y (8.74Ca0.32.5Fe0.8.74Fe2O3 and Z (2.02CaO-97.98FeO) were formed near the w?stite corner of the system. Martin and voge15 postulated the existence of the compounds CaO.9FeO and 4Ca0.3Fe3O4; the former is very close to the composition of point Z and the latter to that of CaO.FeO-Fe2O3. The most valuable contribution to the presen knowledge on this system was made by Cirilli and Burdese6-8 who showed by X-ray and chemical anal yses that there were two ternary compounds, CaO-Fe0.Fe2O3 and CaO.3FeO-FezO3; the former is the same as that suggested by Schenck et al. and the latter is close to their point X. The results of Cirilli and Burdese show that the phases Y and Z postulated by Schenk et al. are solid solutions of calcium oxide in w?stite. In most of the above-mentioned reduction-equilibria measurements carbon monoxide-carbon dioxide mixtures were used and in a few cases hydrogen-water vapor mixtures were employed. Using the

Jan 1, 1962

By A. W. H. Morris, E. A. Steigerwald

The jatzgue beizazriov oj Mietal matrix co))zpos~tes in tension -lensiom loading has been imestigated as a junction of Dolume fraclion veinfovcelnent using the model systems of a silver matrix reinforced with contlnuous or dzscontztinuous aligned tungsten jilamenls and continuous aligned steel filamenls. Appreciable impvocetnents in fatigue strength were obseved in all syslems inzvesLigated, the degree of sl renglhenng-increasing with increasing volume fraclion of reinforcement. The mode of fatigue failure was found to be a function of colutrre jp-actiotz and was also noted to be controlled by the relative fatigue and strength characlerislics of the matrix and reinforcemenl. THE advantages to be gained by suitably incorporating high-strength filaments or whiskers into metallic matrices are well-recognized.' To date emphasis has been placed on the experimental determination of tensile strengths and elastic moduli of metal matrix composites measured parallel to unidirectionally aligned filaments. Several attempts have been made to relate experimentally measured tensile properties to theoretical values calculated from the properties of the components on the basis of the relatively simple "rule of mixtures" analysis. However, relatively few data have been reported in the literature on the fatigue behavior and mechanism of fatigue failure of metal matrix composites. In a study of fatigue crack propagation in aluminum plus steel wires and aluminum plus tungsten wires, Forsyth et a1.2 found that the incorporation of small numbers of filaments suitably dispersed were capable of substantially reducing the rate of fatigue crack propagation. For this purpose, the strength of the filaments appeared to be more important than the aspect ratio and the authors reported that parallel filaments were not the most favorable orientation for increased strength. In a basic study of the fiber reinforcement of metals, Williams and 0'brien3 report preliminary results which indicate a considerable improvement in fatigue strength in reversed bending fatigue of a steel wire-reinforced aluminum alloy composite. In a study of the influence of interfacial bonding on fatigue behavior, Baker4 has also reported improved fatigue properties in stainless steel-reinforced aluminum composites. In contrast, Ham and place5 report that, although tensile properties are improved greatly by filament reinforcement, the reinforcement of copper with continuous, brittle tungsten wires up to 23 vol pct was comparatively ineffective against fatigue. The authors attribute the poor fatigue properties of the composite to fatigue hardening of the matrix at the tips of cracks which can build up stress concentrations sufficiently large to fracture proximate filaments. Baker and cratchley6 failed to find marked improvements in the reversed-bending fatigue properties of silica-reinforced aluminum. The study was complicated by the complex behavior in a composite during the compres-sive half-cycles imposed in this type of loading. This was manifested in the failure of the composites by de-lamination, a contributing factor being the presence of aluminum oxide at the matrix-filament interface. Prior to the general acceptance of filament-rein-

Jan 1, 1968

By N. A. Tiner

A study was made of the effects of temperature, type of loading, and electric polarization on the fracturing behavior of copper and zinc coated with mercury. Copper showed an em-brittlement only in cyclic loading, whereas zinc showed an em-brittlenzent in both static and cyclic loading. The embrittle-ment of zinc in static loading was prevented by sub-zero cooling to a temperatzcre of about -70°F. The emhrittlement of both metals was sliglztly reduced by cathodic polarization of mercury. The basic processes involved in fracturing were discussed in the light of these observations. When a solid metal is in contact with certain liquid metals possessing high wetting characteristics, a weakening effect is produced, and the solid metal fractures in brittle manner at a relatively low stress. This lowering of the fracture stress generally is considered different from the stress cracking caused by a corrosive liquid environment and is attributed to the lowering of the solid-liquid interface tension at the grain boundaries.1-4 The purpose of this paper is to describe a number of observations on the special features of fracturing of copper and zinc coated with a liquid mercury film, and to analyze the basic processes involved in fracturing in the light of these observations. EXPERIMENTAL OBSERVATIONS I) Effect of Type of Loading—The evidence appears to indicate that in static loading, metals usually fracture by the initiation of microcracks in the interior preferentially at the grain boundaries or at the intersection of slip bands.' In cyclic loading, cracks develop on the surface within the active slip zones, and gradually propagate with increasing num- ber of cycles.6'7 Because of this difference in the manner of initiation of cracks, a series of bare and mercury coated copper and zinc specimens was subjected to static and cyclic loading, and their fracturing behavior was examined. The specimens were machined to 0.25 in. in diam and 1 in. in length from a high-purity commercial bar stock, and annealed at an appropriate temperature. Mercury was applied to the surface of the specimens by rubbing with cotton wool soaked in a saturated solution of HgCl2 or by etching with a dilute solution of HC1 and rubbing with purified mercury and by washing in water. The static tension load-extension curves were obtained by means of a Riele Screw Power Universal Testing Machine. The room-temperature load-extension curves for copper and zinc are shown in Fig. 1. The deformation behavior of copper, as judged from the general configuration of the load-extension curve, was not affected by mercury coating. The maximum load to fracture and the elongation at the maximum load were practically the same for both specimens. The mercury coated copper, however, showed somewhat less localized necking and had smaller reduction of area than the uncoated metal. The behavior of mercury coated zinc was radically different from the behavior of uncoated metal. The load-extension curves were the same at the

Jan 1, 1962

By R. F. Decker, J. R. Mihalisin

Phase transformations in a series of relatively pure nickel-titanium-aluminum binary and ternary alloys were studied. The purpose was to clarify age-hardening mechanisms, especially in predominantly titanium-hardened compositions. The micro-structures, as determined on a tirne-temperature-transformation basis by light and electron microscopy and X-ray diffraction, were correlated with room temperature and hot hardnesses. The stability of the ? phase under nonequilibrium conditions was shown to be important in this system. MANY of the alloys designed for service in the temperature range of 1200oF (649°C) to 1800°F (980°C) are austenitic iron-.nickel base alloys hardened by titanium and aluminum. The control of high-temperature properties of these alloys has been advanced by the knowledge of microstructures provided by the equilibrium diagrams of Taylor and Floyd1 and Taylor.2, 3 However, there have been notable instances in the predominantly titanium-hardened alloys where the correlation of properties with microstructure and the equilibrium diagrams has been unsuccessful. Mihalisin and carrol14 have noted in electron microscope studies of commercial alloys of this type that a fee phase precipitates and transforms to 71 (hep Ni3Ti) in stress-rupture tests. Bieber5 found that this fee phase remained in nickel-chromium-titanium alloys even when aluminum was excluded. Age hardening in iron-nickel base alloys has been attributed to 71 by Craver, Aggen, and Dyrkacz,6 ? (fee phase based on Ni3Al) by Beattie and Hagel7 and both phases by Lena,8 Yet, on the basis of the nickel-titanium-aluminum equilibrium diagram of Taylor and Floyd shown in Fig. 1, it has been difficult to understand the presence of ? in low aluminum alloys. Furthermore, the characteristic coarse dispersion of 71 has not been commensurate with the marked aging response. Also there have been anomalous grain boundary transformations in the iron-nickel base alloys which have markedly reduced notched stress rupture properties.9 These have been related to boron content and residual cold work. Recently, Golubtsova and Mashkovich,10 Buckle and Manene11 and Bogaryatskii and Tyapkin12 have noted a transition fee Ni3Ti in titanium-hardened nickel-base alloys. It was apparent from the latter studies that a transition phase was important in the nickel-titanium-aluminum system. The purpose of this study was to identify this phase, measure its transformation characteristics and kinetics, and attempt to correlate these findings with age hardening. It was believed that time-temperature-transformation studies, because of their adaptability to transition phases, would be of most value for this investigation. Accordingly, this method of study was undertaken on relatively pure nickel-titanium-aluminum alloys with controlled variations in boron content and residual cold work. EXPERIMENTAL PROCEDURES Compositions were selected from the nickel-titanium-aluminum isothermal section of Taylor and Floyd.' These compositions are plotted in Fig. 1 and were selected to obtain equal aging potential of approximately 15 pet by volume of the equilibrium precipitate. The materials were vacuum melted from

Jan 1, 1961

By R. W. Smashey, B. J. Piearcey

The structure, composition, and morphology of the carbide phases present in the nickel-base superalloy, Mar-M200, hare been determined and three carbide phases observed. The MC carbide is a solidification product, and the M23 Co and M6C carbides are both prod~icts of solid-state precipitation. The identity of each phase usas determined by both X-ray and electron-diffraction techn~ques. Compositions of all three carbides were studied using the electron beam micro-probe analyzer and by unalyszs of electrolytically extracted residues. Optical and electron microscopy were employed in order that the time/temperature -dependent behavior of the carbides might be observed. Supplementary studies were completed on thin foils and oriented single crystals to determine the mor-phology and orientation relationship of each phase with that of the matrix. MAR-M~OO* is a high-temperature, creep-resistant superalloy designed for use in the as-cast condition. The "as-cast" microstructure consists of a solid-solution matrix, referred to as gamma (y), which contains a general, coherent precipitate of the inter-metallic Ni3(A1,Ti) referred to as gamma prime (?). As a result of dendritic segregation during solidification, a degenerate, spherulitic ? -?' eutectic constituent is present at the grain boundaries and the in-terdendritic regions, which is nucleated by the y on the dendrite tips. A primary carbide phase, a solidification product, is also present at the grain boundaries and in the interdendritic areas, and an additional carbide appears at the grain boundaries as a fine discontinuous precipitate. The alloy is particularly susceptible to heat treatment. For example, the mechanical properties of the columnar grained mater- ial are substantially improved by solution heat treatment, followed by an intermediate temperature age. Metallographic examination of heat-treated material reveals, however, that exposure to elevated temperatures has a marked effect on the microstructure of the alloy; in particular, it is observed that precipitation of considerable amounts of various carbide phases occur. The following investigation was carried out to determine the morphology, composition, and behavior of the carbides in Mar-Ma00 as an aid to the determination of their effect on the mechanical properties and stability of the alloy. THE PRIMARY MC CARBIDE The MC carbide phase appears in the interdendritic interstices and the grain boundaries. In directionally solidified Mar-M200 the carbide appears as very small particles in the chilled region, Fig. l(a), whereas in material less affected by the chill, it becomes larger and develops a dendritic morphology, Fig. 1(b). Step polishing of metallographic specimens from this region shows that in directionally solidified material the individual carbide dendrites are connected in a dendritic network within the metallic interdendritic interstices, whereas in material from the chilled region and in conventional Mar-M200 they are discontinuous, isolated dendrites. No orientation relationship exists between the primary carbide and the matrix.

Jan 1, 1968

By David B. Burrows, Rlkl Kobayashi, Norman L. Carr

The viscosity of hydrocarbon mixtures, whether in the gas or liquid phase, is a function of pressure, temperature, and phase composition. This paper presents methods for the prediction of the viscosity of the gas or less dense fluid phase over the practical range of pressure, temperature, and phase compositions encountered in surface and subsurface petroleum production operations. The correlation necessary to predict the effect of pressure on viscosities is presented in Part I. Serious discrepancies in high pressure gas viscosity data in the literature are discussed. The application of the correlation to predict absolute viscosities is discussed in Part 11. Auxiliary correlations are presented to enable calculations of viscosities from a knowledge of the pressure, temperature, and gravity of the gas phase. INTRODUCTION A knowledge of the viscosity of hydrocarbon fluids is needed to study the dynamical or flow behavior of these mixtures through pipes, porous media, or more generally wherever transport of momentum occurs in fluid motion. Since flow is predominantly in the laminar region in petroleum reservoirs, the influence of fluid viscosity on this flow is especially important. As early as 1894, Onnes1 and Onnes and de Haas' noted that the viscosities of homologs under corresponding states could be correlated. The theorem of corresponding states has been further developed and applied to the viscosity of pure, nonpolar gases under pressure by Comings, Mayland, and Egly.3 It was demonstrated that the viscosity ratio could be expressed rather closely as a function of reduced pressures and temperatures, 1.e.: µ/µ1 = f( TR2 PR) ........(1) temperature, absolute units where: TR =------------------------------ ------ critical temperature. absolute units _pressure, absolute units critical pressure, absolute units µ = viscosity of gas at reduced temperature TR and reduced pressure PR µ1 =. viscosity of gas at atmospheric pressure and at temperature TR Serious discrepancies in the viscosity of pure hydrocarbon gases at high pressures have been called to Our attention by Comings, and and Egly. They made a careful analysis of the following methods commonly used to measure gas viscosities: 1. Oscillating disc viscometer4,5 2. Rolling ball viscometer6,7 3. Capillary tube viscometer12 On the basis of their analysis of the problem and their experimental data on the viscosities of methane, ethylene, carbon dioxide, and propane, they preferentially selected data obtained by the capillary tube viscometer to develop their viscosity correlation. Since then a need has existed to verify the experimental technique of Comings, Mayland, and Egly for the determination of viscosities at high pressure; to extend the data to mixtures of hydrocarbons; and to extend the range of their correlation to include higher pressures. Using the correlation procedure of Comings, May-land, and Egly, the prediction of gas viscosities is resolved into the correlation of the effect of pressure, temperature, and composition on the viscosity of hydrocarbons and their mixtures and the prediction of viscosities of mixtures of hydrocarbons and other natural gas components at one atmosphere pressure.

Jan 1, 1955