Search Documents

By Caudle B. H., Cooper H. E. Jr., O. K. Kimbler

The results of studies of areal sweepout behavior in nine-spot injection patterns are presented in this paper. The ratio of the production rates of the two types of producing wells in a nine-spot pattern is considered in its effect on breakthrough. A model study was used to develop a method to predict the production histories of both side and corner wells and to develop the production history of the pattern or the field. INTRODUCTION The importance of areal sweepout behavior in injection operations has been recognized for a number of years. We now know that the fraction of a reservoir which will be reached by an injected fluid is a function of the geometric arrangement of the production and injection wells and of the mobility ratio of the fluids. Of these two, the mobility ratio (which is a measure of the relative ease with which the oil and the injected fluid can move through the reservoir) appears to have the greatest effect on recovery. The effect of mobility ratio on production history has been reported for most of the dispersed injection patterns (i. e., five-spot, staggered and straight-line drives).4-6 ere has been very little published on the nine-spot injection pattern. This may be because the two types of producing wells in the nine-spot pattern can—and sometimes should —be produced at different rates. This adds a second variable (the fist being mobility ratio) to be covered in a study of the nine-spot flooding network. Muskat1 has reported the sweep pattern efficiency at breakthrough for a mobility ratio of one at various ratios of producing rates for the two types of wells. For these conditions he found maximum oil production at breakthrough to occur when the corner well (the producing well farthest from the injection well) is produced 10.7 times as fast as the side well. Other investigatorsa2,3 have studied a few of the many possible operating conditions possible with this injection pattern. This paper presents the results of studies which are strictly applicable to a nine-spot injection pattern surrounded by other nine-spots in a homogeneous reservoir and which has no flowable gas present (no oil bank is formed). Although the full ranges of the variables mentioned above have not been covered, the results reported here should allow reasonable estimates of field operations to be made. EXPERIMENTAL The well spacing geometry of the nine-spot pattern is shown in Fig. 1. Here we see that each injection well is surrounded by eight production wells arranged in a square. Four of these producing wells are located at the corners of the square; the other four are in the midpoints of the four sides. These two types of producing wells are called "comer wells" and "side wells" respectively. It is the ratio of the producing rates of these two types of wells that affects the breakthrough recovery, as calculated by Muskat.' This ratio is defined as the total producing rate of a corner well divided by the total producing rate of a side well. The model used in this study represented one-eighth of a nine-spot pattern, as shown in Fig. 1. It contained the equivalent of one-fourth of a side well, one-eighth of a comer well, and one-eighth of an injection well. Because of these proportions, the actual producing rate ratios in the model were one-half of the ratios of producing rates as

Jan 1, 1965

By R. Fawley, M. A. Quader, R. A. Dodd

Stacking fault energies and annealing twin frequencies have been measured for austenitic stainless steels having a) constant 20 wt pct Cr and varying nickel contents, and b) constant 20 wt pct Ni and varying chromium contents. The effect of nitrogen has also been studied and, to a lesser extent, so has the effect of carbon. All measured stacking fault energies plot linearly against the corresponding annealing twin frequencies, suggesting that, for constant prior deformation and grain size, twinning frequency can be used to estimate stacking fault energy. Compositions low in nickel possess the lowest fault energy, while the maximum fault energy within the investigated composition range occurs mound 20 pct Cr-20 pct Ni. Nitrogen has practically no effect on stacking fault energy when increased from 0.005 to 0.05 wt pct, although Planar dislocation glide is associated with higher nitrogen contents; this may be a short-range order effect. Carbon may raise the stacking fault energy a little, and causes pronounced dislocation tangling in deformed alloys. The basically different dislocation structures promoted by nitrogen and carbon, respectively, are not associated with large variations in stacking fault energy, and the reason for the difference remains unknown. INTEREST in the dislocation configurations developed in plastically deformed alloys arises principally from a desire for an understanding of mechanisms of plastic deformation and fracture. Comparatively little basic work has been concerned with austenitic stainless steels, although considerable interest has developed in the fundamental aspects of deformation of these alloys since the suggestion that those compositions deforming essentially by planar glide are particularly prone to transgranular stress corrosion cracking.' Certain facts are well-established. An 18 Cr-8 Ni steel (type 304) has a low stacking fault energy which is increased by higher nickel contents, and the structure of these steels when moderately plastically deformed changes concomitantly from planar to less planar to distinctly tangled dislocation configurations. These changes are thought to relate to changes in stacking fault energy, and considerable effort has been expended in measuring stacking fault energies of austenitic stainless steels through the determination of node curvatures2"4 even though the method has limitations due to formula approximations,5 an upper limit of measurement of 50 erg cm-2 at the most,5 and the necessity of an extremely meticulous experimental technique. Therefore, it is not surprising that only qualitative agreement between different investigators is generally to be found.'-' At high energies where node radius measurements are inappropriate, some use has been made of annealing twin frequencies to estimate relative stacking fault energies, although a recent critical evaluation of the method suggests that it should be used cautionsly with due regard to effects of grain size and prior deformation.6 Finally, there is a question as to whether the structures of some deformed steels are due to ordering effects. In particular, the role of nitrogen in promoting planar dislocation motion has been suggested to be due to ordering,' but similar suggestions have been made for steels having low interstitial contents.4 EXPERIMENTAL Small ingots of austenitic stainless steels (-50 g) were prepared from components exceeding 99.99 pct purity, the nickel and chromium being Johnson Matthey "Specpure" metals. Carbon was added as pure graphite, and nitrogen as CrN. The components were accurately weighed, and it was assumed that the final composition was the same as the nominal composition

Jan 1, 1969

By George P. Chapman

Mica is a platy mineral occurring in a variety of complex hydrous aluminosilicate forms with differing chemical composition and physical properties. Principal minerals in the mica group include: Muscovite-potassium mica (colorless or pale green/ ruby) Phlogopite-magnesium mica (dark brown or amber) Biotite-magnesium-iron mica (black or dark green) Lepidolite-lithium mica (lilac) Selected properties are given in Table 1. Muscovite is most important commercially with phlogopite of lesser use. The laminated structure of mica enables it to be split into very thin films which are transparent and tough as well as having outstanding dielectric and insulating properties. Commercially, mica is used in a number of forms (Chowdbury, 1941; Rajgarhia, 1951; Skow, 1962). Sheet mica consists of flat sheets mined from naturally occurring books of mica, free from defects and capable of being punched or stamped into required shapes. Sheet mica is separately classified into blocks, films, or splittings according to thickness. Built-up mica, or micanite, is made by arranging overlapping splittings in layers , cemented with a binder and pressed together at high temperature. Reconstituted mica, or mica paper, is made by depositing fine flakes of high-quality scrap mica in a continuous film impregnated with binder. Scrap and flake mica are normally unsuitable in quality or size for making sheet mica. Originally the term scrap mica referred to the waste byproduct of mining and fabricating sheet mica, and distinct uses were developed for this material. Subsequently it became economically feasible to mine lower quality mica for these uses, and the term flake mica was introduced. Although the two terms are still used somewhat synonymously, it is considered better, at least in the United States, to use the term flake mica in referring to mica mined for uses other than as sheet mica; and to restrict the term scrap mica to mica mined for or with sheet mica, but which will not meet the specifications. Synthetic mica, such as fluorophlogopite, is produced by slow crystallization of a melted blend of pure raw materials. Mineralogy In the true sense the term mica does not relate to, a particular mineral, but to a group or family of minerals of similar chemical composition and to some extent similar physical properties. These minerals are predominantly potassium aluminum silicates with varying amounts of magnesium, iron, and lithium. The precise formulas and isomorphic relationships of the various group members have been studied, but general agreement has not been reached (Grimshaw, 1971; Hurlbut, 1952; Skow, 1962). The general formula describing the chemical composition of micas is [X2Y4-6Z8020(OH, F)4, where X is mainly K, Na, or Ca; Y is mainly Al, Mg, or Fe; Z is mainly Si or Al (Deer, et al., 1962).] These minerals have an internal structure of the layered lattice type where the silicon atoms are in the center of a tetrahedral grouping of oxygen atoms. The groups are linked together in a single plane by three oxygen atoms that lie within the common plane. Each of these oxygen atoms is shared by two tetrahedra. These linked tetrahedral groups, when continually extended, produce a hexagonal network within the plane. This internal structure of the mica has been used to explain the ex-

Jan 1, 1983

By C. W. Carpenter, P. T. Bail, J. E. Bobek

This paper presents the results of model studies made to demonstrate the validity of applying the "basic" waterflooding scaling relationships of Rapoport1 to water-wet reservoirs composed of communicating strata of different permeability. Results demonstrate that these relationships can be validly applied, and also show the combined effect of variables on recovery. This demonstration was needed to confirm that the sizable effects of communicating strata on waterflood behavior, observed in model studies, were actually representative of field behavior. INTRODUCTION Rapoport1 Collins2 and others have presented scaling laws for modeling water-oil displacements. The validity of these laws has been experimentally demonstrated for homogeneous systems only. Recently, however, several investigators have presented the results of multilayer model studies made to determine the effects of viscous, capillary and gravitational forces on oil recovery in systems composed of communicating layers of different permeability. Dyes and Braun,3 using miscible displacements to simulate water flooding, showed that vertical communication adversely affects recovery at unfavorable viscosity ratios in the absence of capillarity. Ogandzhanyants and Egorova, 4 Gaucher and Lindley,5 and Richardson and Perkins6 modeled water-oil displacements in layered systems using immiscible fluids with capillary forces present. These investigators found more efficient behavior than in the miscible system of Dyes and Braun. However, since the scaling laws had not been verified for heterogeneous systems prior to or during these tests, it was necessary to assume that the results were representative of field behavior. This report presents the results of model studies made at Jersey Production Research Co. to find out if the waterflooding scaling relationships are valid when applied to water-oil displacements in heterogeneous reservoirs with vertical communication. Data obtained in the study show the combined effects of viscous, capillary and gravitational forces on oil-recovery behavior. The studies were performed in strongly water-wet systems where strong imbibition forces were present. For systems of different wettability, the effects of capillary imbibition would be somewhat different than those presented. APPROACH The scaling laws studied were those developed by Rapoport1 and designated by him as "basic" scaling laws. These relationships require that the model be scaled to the geometry of the prototype, and that the model and prototype be operated at the same viscosity ratio and have identical relative permeability curves, contact angles and boundary conditions. It is also necessary that the groups** be identical in the two systems, although any of the parameters making up the groups may be different. Finally, the capillary pressure of one system must be directly proportional to that of the second. Studies were conducted in two four-layer models, representing quadrants of five-spots, which were geometrically similar and which had the same glass-bead packing. The fluids used assured the same wettability in both models. Thus, the contact angles and relative permeabilities of comparative sand layers in the two models were identical and the capillary pressures were directly proportional. However, one model had a characteristic length three times that of the other. To make the scaling groups equal and to check the scaling laws, it was necessary to adjust the rate, water-viscosity level, interfacial tension and water-oil density difference to compensate for the difference in model sizes.

By A. S. Appleton, M. B. Bever

The stored and expended energies of an Au-Ag alloy deformed in torsion were investigated as functions of strain, strain rate, and temperature. At room temperature, the stored energy, measured by tin solution calorimetry, increased linearly up to an intermediate strain, above which it was nearly constant; at 78 °K the relation was linear up to fracture. Approximate values of the energy stored at 4 OK indicate a rapid increase below 78 OK. The energy stored by specimens deformed successively at 4o and 78oK changed slowly with increasing second strain from the curve for energy stored at 4 OK (measured after annealing at 78oK) to that for deformation at 78°K. The ratios of the stored to the expended energy at room temperature and 78 oK were unusually large. The additional amount of energy stored at the lower temperature is attributed mainly to an increase in the number and energy of dislocations. The stored energy as a function of strain rate at 4oK (measured after annealing at 78oK) increased to a sharp maximum over a narrow range of strain rates, whereas the expended energy changed only slightly. These effects are explained by the generation of point defects resulting from the enforced nonconservative movement of jogs in fast moving screw dislocations. The effect of straining successively at two strain rates at 4oK was also investigated. Stress-strain curves for 4o, 78oK, and room temperature and the results of micro examination of specimens deformed at these temperatures are also reported. THIS investigation is a continuation of a research program primarily concerned with the effects of variables on the energy relations involved in the deformation of metals. The variables investigated in earlier work have included strain, strain rate, temperature of deformation (room temperature and 78oK), and the type of deformation process. Most of this work has been carried out with Au-Ag alloys. In the investigation reported here, the deformation process was torsion, which had not been used previously in the program. The stored and expended energies involved in the deformation process were measured as functions of strain, strain rate and the temperature of deformation in the range 4" to 373" K. The microhardness and microstructure of deformed specimens were also investigated. The relation between stored energy and strain differs for different deformation processes.1,2 In general, the stored energy increases with strain and may attain a nearly constant value at large strains. This value and the rate at which it is reached, however, depend on the process of deformation. This dependence has been attributed, at least in part, to differences in the effective strain rate and rise in temperature of the specimen during deformation. The effects of the temperature of deformation on both the stored energy and the energy expended in the working process have been the subject of only a few investigations.3-6 Values of these quantities at low temperatures are of special interest as they yield information on point defects which, for many metals, is not obtainable at higher temperatures. The effect of the strain rate on the stored and expended energies has received little attention The strain rate has usually been measured only in relative terms, and hence the interpretation of its effect on the stored energy has been mainly comparative.

Jan 1, 1963

By H. D. Yoo, M. R. Tek, D. L. Katz

The behavior of gas-storage reservoirs subject to water drive is investigated through analog simulation on an electronic differential analyzer. The simulation technique developed on an LM-10 computer permits the prediction of reservoir volume or pressure resulting from the movement of water in the surrounding aquifer. The method developed on the analog computer consists of setting up an appropriate transfer-function circuit and feeding the arbitrary time-varying boundary conditions as an input signal. The input may be specified as gas reservoir pressure, pore volume or the water flux. Several cases studied include an isolated gas reservoir on a limited aquifer, interference among three reservoirs adjacent to a common aquifer and the growth of gas-storage volume on an aquifer. It is concluded that the method developed on an electronic differential analyzer provides an excellent technique to simulate and investigate the behavior of gas reservoirs subject to water drive. The agreement between the reservoir performance as predicted from the simulation technique and as measured from actual field data is found to be better than the range usually encountered in predicting water-drive behavior. INTRODUCTION It is generally known that some gas-storage reservoirs are located on top of blanket sands of large extent, saturated with brine called aquifers. Because the volume of the body of water associated with aquifers is usually very large and water is compressible, the cyclic pressure variations encountered in normal storage service inevitably cause unsteady, compressible flow conditions in the adjacent aquifers. The solution to radial diffusivity equation for a limited aquifer for constant terminal conditions has been know111 since the early 1930's. The solution for the constant terminal conditions for an infinite aquifer was puhlished in 1949.2 The proldem of handling the unsteady flow of water through a porous medium with time-varying boundary conditions has been studied by many investigators through the use of graphical,3 digital4 computing techniques or on an R-C type of electrical analog called a reservoir analyzer.5 The digital computer performs a series of arithmetic calculations to superimpose the solutions of constant terminal conditions, while the R-C type of analyzer permits the simulation of the continuous medium by means of "lumped-cell" electrical resistance and capacitance elements based on finite-difference approximations. The graphical method is based on the convolution integral solution of the partial differential equalion. The purpose of the present study was to simulate the behavior of an aquifer on a general-purpose, electronic differential analyzer to obtain the influx of water or the change in pressure at the reservoir continuous1r and quickly. The use of the electronic differential analyzer was based on well known solutions for the constant terminal conditions already available in the literature.2,6-8 THEORETICAL DEVELOPMENT MODEL. The gas reservoir (R) is described in relation to an aquifer in Fig. 1. The permeability and porosity of an aquifer sand, the viscosity of the brine, and the compressibility of the brine and the formation are assumed to be constant. It further is assumed that the blanket sand is not thick enough to give appreciable vertical pressure distribution. The model in consideration is circular with radial geometry. The aquifer radius can be of limited or infinite extent. The gas-water interface is assumed to be fully segregated, and the displacement of the gas by

By G. F. Sager, B. J. Nelson

Magnesium alloy forgings offer higher and more uniform mechanical properties than heat treated magnesium alloy castings and are used principally for light weight parts that may be stressed in fatigue or subject to impact loads, or where space limitations do not permit the use of the necessarily bulkier magnesium alloy castings. Compositions and Properties of Magnesium Forging Alloys The nominal compositions and properties of the principal commercial magnesium forging alloys are given in Table 1. The two that are most commonly used are AMC58S and AM65S. The former has the highest strength and is, therefore, employed for heavy duty applications. However, the forging of this alloy and of AMC57S ordinarily requires the use of slow speed hydraulic presses. The forging alloy AM65S combines good, although somewhat lower, mechanical properties with excellent forging characteristics. This alloy can be forged on hammers, upsetters, rolls, and mechanical presses, as well as on hydraulic presses. These characteristics make it particularly useful for many applications. Manganese Segregation in AM65S The alloy AM65S contains 5 pct tin, 3 1/2 pct aluminum, and a small amount of manganese, the manganese being added to insure satisfactory resistance to corrosion. Some manganese segregation was occasionally encountered in this alloy. In many applications, such segregation is of no particular consequence, but when forgings are acid dipped prior to the application of various chemical coatings, the segregated particles of manganese constituent may stand in relief. The resultant surface roughening may impair appearance and is undesirable in forgings employed in the textile industry, where very smooth surfaces are essential to avoid the catching and breaking of fine threads. An effort was therefore made to determine the cause of manganese segregation in this alloy and find a method for its elimination. Radiographic examination of a series of cast ingot sections and extruded samples of the AM65S type having manganese contents ranging from zero to about 0.7 pct revealed no appreciable manganese segregation when the manganese was less than about 0.4 pct. A small amount was observed with a manganese content of 0.46 pct and considerable with manganese contents of 0.6 pct or higher. Attempts to eliminate the manganese segregation by variations in the melting and casting conditions were unsuccessful and it soon became apparent that the trouble was attributable to the fact that the manganese contents that caused segregation were in excess of the amounts that would remain in solution at temperatures encountered in the melting and/or casting operations prior to the complete solidification of the ingots. A knowledge of the amounts of manganese that would be soluble in molten alloys of the AM65S type at various temperatures was obviously desirable. The liquid solubilities of manganese in binary Mg-Mn alloys and in Mg-Al-Mn and Mg-Zn-Mn alloys have been determined by Tiner and others,* but no data on the solubility of manganese in molten magnesium alloys containing tin and aluminum are given in the literature. For this reason, an investigation to determine the solubility of manganese in a magnesium alloy containing 5 pct tin and 3.5 pct aluminum (AM65S type) was undertaken.

Jan 1, 1950

Discussion of the paper of DORSET A. LYON and ROBERT M. KEENEY, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin. No. 92, August, 1914, pp. 1791 to 1800. LAWRENCE ADDICKS, Chrome, N. J.-I read this paper for the first time this afternoon, and it is really worthy of a much more careful reply than I can make with such a short time to consider it, but I just want to say that I differ with Dr. Lyon in his premises and conception of what happens in a refining furnace. He cites steel as an instance where the production of special grades justifies the high cost of power in an electric furnace, and goes on to say the same will be true in the case of copper, for the reason that you will get a better quality of product. I don't think you will get a higher grade of copper,. or a better conductivity, as I will explain in a moment. The cost of fuel in the Eastern plants is somewhere between 30c. and 40c. per ton of copper refined, and, if my memory serves me correctly, in an open-hearth steel furnace it is something like $1.25, so it is evident that steel could be handled to better advantage than copper on the basis of fuel. Now, taking the Great Falls plant to compare with is not quite fair, because that plant operates under peculiar conditions. The furnaces are relatively small; the coal is very bad and is very high in sulphur. No one would think of using a coal with 3.6 per cent. sulphur were anything better available. Due to these conditions, the amount of slag is inordinate, it being quoted as 3.5 per cent., and it is necessary to use lime, as there is a tendency to have troubles from arsenic owing to the very high current density used. I think he has taken about as hard a case as he could pick out. Now as to the conductivity of copper, my own idea about the reason that melted copper does not give as high a conductivity as pieces drawn directly from a cathode, or native copper, is that in the latter case the impurities are present as a mechanical mixture, while after melting they are chemically combined with the copper, which is a very different condition. Further, it is necessary to take the sample from a relatively smooth and consequently pure part of the cathode, as otherwise it would not draw. The same with the mass of copper; you pick out a good solid part of the copper, which is not representative. In fact, the refiners have all found they could not take fair samples of cathodes for a chemical analysis. It is always customary to use wire-bar copper -for the purpose of sampling, and the impurities are several times as great as shown by samples taken from .the cathodes. I think if we examine all of the examples he has given of cases where copper is higher in conductivity, it will fit with that explanation. For example, the Elmore process is a direct electrolytic deposit. Incidentally, at the present time there are a number of ex-

Jan 12, 1914

By E. A. Holbrook

AT the meeting of the Committee on Engineering A Education of the Institute at the New York meeting last February, it was brought out that the number of men graduating in mining engineering from our colleges at the present time is not sufficient to meet the ordinary needs of the mineral industries. Following the meeting, Samuel S. Wyer, consulting engineer of the Fuel-Power Transportation Educational Foundation of Columbus, Ohio, prepared a pamphlet called "Mining Engineering's Appeal to High School Seniors." Under the auspices of this Foundation the pamphlet is being sent to every high school in the United States. The pamphlet does not in any way paint glowing word pictures of the profession; rather it is a statement of the importance of mining engineering in our present-day civilization, together with the requirements in young men who are looking forward to an engineering career.

Jan 1, 1930

By Arthur Dwight

WE NOT have to go so very far back, when measured in actual years, to what may be considered the beginning of the industrial era of the great West, the discovery of gold in California in 1848, just 74 years ago. By a strange coincidence, this event occurred within a few days of the signing of the treaty with Mexico which ceded California to the United States. Needless to describe the mighty wave of humanity that hurled itself toward the setting sun in response to that call. The single thought in every one's mind was gold. The gold as they found it in placers or ledges could be so easily worked, and the product was so readily transportable, and available immediately as money, that practically no attention was paid to deposits of the base metals, in the treatment of which cheap transportation was a paramount con-sideration; consequently little progress was made in anything but gold mining until after the Civil War. The next great step was accomplished when East and West were united by the successful construction of the Union Pacific Railroad from Omaha across the great plains and through the Rockies to meet the rails of the Central Pacific coming eastward across the Sierras. The industrial history of our great West really dates from the day when those two hands of steel were joined, on the shores of the Great Salt Lake at Prom-ontory Point,. May 10, 1869. That seems a long time ago when we think of the enormous changes that have been wrought since that day, and when we regard the rich empire that has sprung up in that western land. Into the new empire thus made accessible, by this first thread of steam transportation, flocked a new brood of adventurous spirits from the older communities of the East. This way walked Fate; and as she, went, flung far the line of destiny, That bound an untracked continent to brotherhood from sea to sea; That long gray trail of dream and hope, marked mile by mile with graves that keep On every barren hill and slope some stout heart lost in dreamless sleep. Patience and faith and fortitude were willed to it and justified; Stern, homely virtues, plain and rude, eternal as the sky and wide. Nor ever sea-king dared the sea in sterner mood than these who went Strong armed to wrest from Mystery their birthright, half a continent.

Jan 4, 1922

By N. E. Brown, F. L. Versnyder

THE apparent dependency of the electrical characteristics of hexagonal crystalline selenium on microstructure has aroused much interest in microscopical studies of selenium. Microscopic observations on the crystallization of selenium have been made by Escoffery and Halperin,' P. H. Keck,' and other investigators. It is the purpose of this paper to discuss the microstructural changes observed on polished cross-sections of single layers of selenium after various heat treatments. Observations were also made on crystallization of the free-surface layer of these deposits. In general, all of the transformations studied were either transformations of the vitreous selenium to hexagonal selenium or micro-structural transformation of the hexagonal selenium itself. Procedure The selenium used in this work was obtained from the American Smelting and Refining Co. and was approximately 99.96 pct pure. An intentional impurity of 1 part per 2,000 of bromine was added to the material prior to evaporation. A thickness of approximately 0.002 in. of this selenium was vapor deposited on an aluminum base plate. The maximum plate temperature during the vacuum vapor deposition was 140°C. Mounting of the cross-sectional specimens for metallographic study could not be done in plastic mounting media, as is customary, since temperatures in excess of 50°C would cause unwanted transformations. Consequently, a simple clamp-type device was used to mount the specimens for preparation. All grinding operations were then done carefully by hand in order that the specimen not become heated during this operation. Wet polishing was done on the conventional metallographic polishing laps, using successively finer grinding powders. An extremely careful polish is necessary, since observation and micrography of the specimens are done in the unetched condition under polarized light. The two observations of crystallization made on the free surface of vitreous selenium deposits (Figs. 4 and 5) were made on surfaces which were perpendicular to the cross-sections studied. These free-surface layers were examined directly, i.e., no pre- vious metallographic preparation, as obtained from the vacuum vapor deposition. Microscopic Observations A study was made of polished cross-sections of the vitreous selenium as-deposited. It was noted that in all cases there was columnar crystallization adjacent to the base plate, which appeared to occur during the vacuum deposition process. This observation has also been made by Keck? It also was observed that vagrant spherulitic crystallization occurred in the vitreous selenium. The term "vagrant" is used, since these spherulitic grains appear to crystallize at random throughout the vitreous selenium during the vacuum deposition process. Columnar crystallization at the A1-Se interface and a typical spherulite observed in a polished cross-section of "as-deposited" vitreous selenium may be seen in Fig. 1. Cross-sectional samples of vitreous selenium studied after heat treating individual samples for 20 min in 10" steps from 80" to 220°C revealed that crystallization—in this case, columnar crystal growth —proceeds from the aluminum base plate to the surface of the specimen (Fig. 2). Crystallization was microscopically observed to be complete after the 130°C heat treatment. Visual examination of the free surface of the specimen after the 130 °C heat treatment revealed the readily recognizable grey appearance of the completely crystallized selenium, in corroboration of the microstructural observations. No microstructural transformations then appeared to take place between 130" and 190°C. At 190°C the beginning of recrystallization appeared and proceeded until the columnar grain structure had been completely transformed to equiaxed grains between 210" and 220°C (Fig. 3). Naturally, the grain size of the recrystallized grains at the lower temperatures (190" to 210°C) was smaller than is illustrated in Fig. 3. In addition, polished cross-sections of deposits heat treated at 140°C for 10 min to cause complete crystallization and, subsequently, heat treated in 10" steps from 80" to 220°C for 20 min were studied. As expected, no microstructural transformations took place until the beginning of recrystallization was observed at 190°C. A comparison with the previously studied specimens revealed that recrystallization proceeded almost identically in the two experiments although in the first case the deposits were vitreous prior to the series of heat treatments and in the second case they had been crystallized by a previous heat treatment. By heat treating for longer times (180 min) at lower temperatures, the

Jan 1, 1956

By M. J. Coolbaugh

Mining potash at depths of 3000 ft or more beneath thick water-bearing sediments in Saskatchewan presented a unique challenge to the North American mining industry. Potash is known to flow under pressure, but the knowledge of its flow characteristics at great depths was inadequate for safe design of mine workings and for assured protection from water above the salt formations. At the 3000-ft. depth of the Canadian mines, the potash is stressed beyond its elastic limit, and therefore mining design must deal primarily with its behavior as a plastic material. Recognizing that careful study would be required in order to assure safety and stability of mine workings in deep potash, IMC initiated an extensive rock mechanics investigation of structural properties of potash and salt under high-stress conditions. This presentation consists of a brief review of the development of some methods of testing potash in the laboratory and in the field; some of the rock mechanics concepts and principles derived; and their application to potash mine design. The mining of potash more than 3000 ft beneath the water-bearing sediments in Saskatchewan presented the unique challenge of designing stable mine workings and assuring protection from overhead water in a material that was believed to flow plastically, but whose behavior as a plastic material was not sufficiently known. Under the stress conditions ordinarily encountered in mining, most rocks behave as elastic materials; that is, they compress slightly under pressure, and rebound when the pressure is released. Salt and potash, however, are different. Even under the relatively low pressures encountered at shallow depths, these materials become slightly plastic and yield to stress by flowing.* The plastic properties become more pronounced at greater depth and pressure, and the question arises as to whether or not the plastic flow will be rapid enough and exert enough pressure to destroy underground structures or interrupt the mining process. It was found, however, that not only was there an insufficiency of information about the behavior of potash and salt, but conventional methods of testing these materials, such as determining the modulus of elasticity, Poisson's ratio, and uniaxial compressive strength, were inapplicable because of the high stress conditions prevailing at the 3000-ft depth. Potash under high pressure, for example, has practically no modulus of elasticity, its stress-strain relationship varies with time, and its compressive strength depends upon the degree of confinement. Elasticity and Stress/Strain Relationship: Fig. 1 shows a standard stress/strain chart for potash as made by the Department of Mines in Canada. Typically, when stress is applied to a hard-rock specimen, the specimen contracts, then expands to its original shape when the stress is withdrawn. This chart illustrates, however, that potash under stress yields to the stress by flowing, and does not expand when the stress is withdrawn. When the applied stress was held constant for 30 min, beginning at points A and C, the strain continued to increase and the potash flowed to points B and D, respectively. Points B, D, F, and H show that the potash did not return to its original shape when the stress was released. Thus it can be observed that potash has practically no elasticity and that the amount of strain depends upon the length of time that the stress is applied. Compressive Strength: The conventional method of determining the compressive strength of hard material is to find the maximum pressure that long slender specimens of the material can withstand without failing. As illustrated in Fig. 2,* line B, a standard 2-in. cube of potash subjected to a conventional type of uniaxial compressive test will exhibit a strength of about 5000 psi. However, the compressive strength exhibited can be made to change by changing the conditions under which the test is made. For example, if teflon plates lubricated with graphite are inserted between the press and the specimen, thus minimizing end constraint, the compressive strength is only about 2500 psi, shown in line A. If a specimen is cut in half, changing the width-to-height ratio to 2 : 1 instead of 1:1, and then tested without lubri-

Jan 1, 1968

NEW MEMBERS The following list comprises the names of those persons who became members during the period Aug. 10. 1918, to Sept. 10, 1918. BATCHELOR,. HARRY D., Laboratory Director, National Carbon Co., Inc., Cleveland, Ohio. BROWNING, C. P., Gen'I Supt., Britannia Min. & Smelt. Co., Ltd., Britannia Beach, B. C., Canada. COMSTOCK, GEORGE F., Met., Chg. of Physical Test Laboratory, Titanium Alloy Mfg. Co., Niagara Falls, N. Y. CONCKLIN, BERT M Chief Engr., Arthur lron Mill. Co., Hibbing, Minn. COWAN, W. A., Asst. Chief Chem., National Lead Co., 129 York St., Brooklyn, N. Y. DAVIDSON, PHILIP Met., Scovill Mfg. Co., Waterbury, Conn. DAVIS, Louis L., Mgr. & Treas., Commonwealth Min. Co., 911 Foster Bldg., Denver, Colo. DAY, P. W Chem. Engr., Western Cartridge Co., 207 E. 12th St., Alton, Ill. DECKER, HAROLD DEBIT, Co. A, 27th Engineers, A. P. 0. 714, A. E. F., Care Postmaster, N. Y.

Jan 10, 1918

NEW MEMBERS The following list comprises the names of those persons Who became members during the period July 10, 1918, to Aug. 10, 1918. ARCHER, EUGENE G., assayer and Chem., Granby Cons. Min. Smelt. & Power Co.,Anyox, B. C., Canada. BAKER, ROBERT C Mech. Engr. and Draftsman, Moctezuma Copper Co., Nacozari, Son., Mexico. BARNES, EDWARD A Supt., Fort Wayne Works, General Electric Co., Fort Wayne, Ind. BARNHART, EDWIN Engr. of Tests, Bethlehem Steel Co., Sparrow's Point, Md. BENSLEY, MAURICE D Pres. and Mgr., Frontier Brass Foundry, Inc., Niagara Falls, N. Y. BRADLEY, JOHN C Met., The American Brass Co., Waterbury, Conn. BRAGG, C. T Works Mgr., Michigan Smelt. & Refin. Co., Detroit, Mich. BRYMER, GEORGE W Min. Engr., 922 Union National Bank Bldg., Scranton, Pa. CHIVVIS, NORMAN Met. Engr., More-Jones Brass & Metal Co., 3144 North Broadway, St. Louis, Mo. CRAWFORD, R. D Prof. of Mineralogy & Petrology, Univ. of Colorado, Boulder, Colo.

Jan 9, 1918

NEW, MEMBERS The following list comprises the names of those persons who became members during the period July 10, 1916; to July 31, 1916: BOYD, ROBERT RUSSELL Supt:,-Arizona -Commercial Min Co., Globe, .Ariz. BRADLEY, HENRY FRANKLIN, Chem, American Smelt & Ref. Co. Murray,:Utah: BROWN, THOMAS ELLIS, JR..:'. L .:.::..55 Hill, St;; Morristown, N. J. CARY, WEBSTER P., Expert Operator,-General Engineering. Co:, Salt Lake City, Utah. CLARK, ALONZO WEBSTER 3223_ Scottwood Ave., Toledo, Ohio. CORP, CLIFFORD Old Dominion Copper Min. & Smelt. 60., Globe, Ariz. CROMBIE, W. RANSOM, Min. Engr Detroit Copper Min. Co., Morenci, Ariz. DELANEY, EUGENE A., Chief Engr., Berwind-White. Coal Mining -Co., Windber, Pa ELBELT, WILLIAM HENRY, Dept. Foreman., Chino Copper Co., Hurley, N. Mex. FOSTER, L. JULIO, Mgr., Minas i Fundicion ; ?La Junta," San Bernardo, Chile, South America. GASKILL, JAMES PHILLIPS, Genl. Mgr.,.Ajo Cons. Copper Co., Ajo, Ariz., via Gila, Ariz. .

Jan 9, 1916

By V. Lessels, W. A. Hamilton

White Pine Copper Co. is a wholly owned subsidiary of the Copper Range Co. The property of White Pine is about 5 miles south of Lake Superior in Carp Lake Township, Ontonagon County, Mich. The new town of White Pine, adjacent to the company plant, is 18 miles south and west of the town of Ontonagon, and about 55 miles north and east of Ironwood, Mich. A diamond drilling program begun in 1937 to develop the orebody was carried on until 1950. During this period a test shaft, known as the Schacht shaft, was sunk on the orebody and approximately 8000 ft of development drift were driven. In an effort to solve the ore beneficiation problems, considerable metallurgical test work was done on ore extracted through the mine development. This work was conducted in a small pilot plant located in the mill of the Copper Range Co. at Freda, Mich.

May 1, 1956

By R. Costantini

A. Brebner (Chairman, Dept. of Civil Engineering, Queen's University, Kingston, Ont., Canada) — Under the heading of friction losses, the author, in Eq. 10, gives the relationship

Jan 1, 1962

By Ralph M. Barnett, Albert K. Smith

During the last few years, a great deal of interest has been aroused in the use of more refined blasting techniques. It has been the effort of many mining companies to reduce powder cost, obtain better rock breakage, reduce drilling costs and provide safer working places. With the advent of new types of powder and such techniques as cushion blasting, line blasting, smoothwall or soundwall blasting, and presplitting or preshearing, these goals are approaching reality. Smoothwall blasting and presplitting have re- ceived much attention at the Climax Molybdenum Co., Climax, Colo., mine because of the large cost factor involved. An experimental program was begun in 1961, and during 1964 to the present has been used in many working areas. Some spectacular results have been achieved by the operating personnel in hard ground, but the most beneficial results have been in areas where the ground has been soft and highly fractured.

Jan 7, 1965

By Theodore Marvin

USE of airplanes to facilitate mining and petroleum operations has definitely left the "doubting Thomas" stage. As a matter of fact, front pages no longer record the novelty of this efficient arm of the mineral industry. We are now down to the facts basis. The recent aviation issue of Engineering and Mining Journal added - to our fund of knowledge on applications which the A.I.M.E. Aviation Committee is extensively adding to through its world-wide compilation of specific data. Another indication of the advance of flying in our. industries is the addition of regular aviation specialists to the staffs of various mining and petroleum companies, who function in the organization the same as do the metal

Jan 1, 1936

By John M. Hird

Control of artesian ground water has played an important role in the development of Texas Gulf Sulphur's phosphate mining venture in eastern North Carolina. To facilitate dry mining methods, 60 million gpd of fresh water is pumped through wells from a limestone aquifer underlying the uniform flat-lying ore section. Hydrologic information revealed from pumping tests has been used in successfully developing a depressurizing system. Computer assistance is used to plan well patterns. High volume pumping has lowered water levels in water wells over a large area in the Coastal Plain without detrimental effects on water quality in the aquifer. Cooperative effort between mining firms will be required to control the ground water as new mines are developed in the district. An intricate observation -well system is monitored regularly over the wide area of pumping effect to ensure that gradient reversals have not caused salt water encroachment.

Jan 1, 1972