Search Documents

By S. C. Sun, John A. L. Campbell

Objective of the ittvestigation was to determine the electrokinetic differences, if ally, of anthracite lithotypes and thus establish the feasibility of making a coqlstituent separation by froth flotation or other surface-dependent processes. The elec-trokinetic properties were determined by streaming potential methods. In addition, chemical and physical analyses of the lithotypes were made to establish nonsubjec-tive parameters for their diflerentiation. Electrokinetic results indicate a difference in the characteristics of the lithotypes. The isoelectric points of 4 anthracites and 12 lithotypes were obtained. It was suggested that the relative flotation rates of the lithotypes were pH dependent and that the maximum flotation rate of anthracite occurs in an acidic circuit. Although there has been an increased interest in the electrokinetic properties of coal,' research on the subject is still in an early stage of development."' To the authors' knowledge, no electrokinetic studies have been made on coal lithotypes, particularly anthracite litho-types. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods. It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface-dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published.? The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results; however, the result? are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation. Experimental Procedure Prior to discussing the experimental work per se, it would be of value to establish an understanding of anthracite lithology. Anthracite Lithology: Coal seams display two different modes of variation, rank and type. A coal's position in the continuous series ranging from peats through anthracites determines its rank. The rank of the material under consideration is anthracite. The different bands of coal which constitute a coal seam are distinctly contrasted in regard to physical properties and chemical composition. These megascopic bands are the coal types and are termed lithotypes., A megascopic examination of 11 anthracites revealed three distinct, homogeneous, lithotypes. The classic description of bituminous coal lithotypes as proposed by Stope" was found to be quite adequate for recognizing the three lithotypes in anthracite, namely vitrain, durain, and fusain. The term vitrain describes the brilliant constituent of coal; durain describes dull coal; and fusain is the term applied to fossil charcoal. The anthracites studied were generally found to contain 60-80% vitrain, 10-30% durain, and 1-10% fusain. A complete description of the physical characteristics and chemical composition of the studied lithotypes can be found in a previous publication.' Sample Preparation: Nine of the anthracites used in the investigation were from Pennsylvania, one was from Russia, and one from Wales. Table 1 shows the various designations and sources of the employed anthracites. The letter V, D, or F added to the whole coal designation indicates respectively the vitrain, durain or fusain lithotype of that coal. The samples were carefully collected to avoid contamination. To insure against oxidation, the samples were obtained as fresh as possible and stored under nitrogen or water. Generally a representative sample of the seam and samples containing high concentrations of one or another of the petrographic constituents were secured for each coal. Pure lithotypes were prepared by manual separation and selection. The pure lithotypes and representative samples were ground to —35 mesh and screened to 35 x 48 mesh. The 35 x 48-mesh fraction was then passed over a magnet to remove iron contamination, washed with doubly

Jan 1, 1971

AS I told you in the chapter on salts, saltpeter is a mixture composed of many substances extracted with fire- and water from arid and manurial soils, from that growth which exudes from new walls or from that loosened soil that is found in tombs or uninhabited caves where the rain cannot enter. It is my belief that it is engendered in these soils from an airy moisture that is drunk in and absorbed by the earthy dryness. Considering its effects, I do not know how to decide and say exactly what the nature of saltpeter is. The learned and very wise physicians find it salty and with a subtle sharpness both in taste and in their medical experiments. Considering its strong biting qualities, they decide to say that it is of a hot and dry nature; on the other hand when they see that it is engendered from the air and that when touched by fire it becomes inflammable and vaporous, and rises with a fearful impetus when mixed in powder for military guns, it manifestly shows itself to be of a hot and moist airy nature. And then when they see that it is shining and transparent with whiteness and is fusible in every fire in a manner corresponding to a thing of a watery nature, and since it. is heavy, it seems that it can be said to be watery in nature. To this is added the experience of touch and of the great cooling action which it has on water in summertime when wine is to be cooled, and since it crushes and breaks with but little pressure, it might be thought to be earthy in nature; especially when it is seen to change into a hard, white stone when burned with an equal amount of sulphur. Thus it seems that every one of the elemental qualities is predominant in it. Now the ancients called this, or a similar thing, nitrum. [150] Pliny, in Book XXXI of his Natural History, has said that it was a thing not much different from salt, that doctors do not seem to have yet known its nature, that it is found in various places, and that the best is found in Macedonia. But among the moderns and especially in our regions, it is not known today what it is that Pliny and other writers refer -to, since according to the aforesaid Pliny and other ancient writers it is a natural mineral. Some say that in place of, the natural kind the artificial will serve for the same medicinal purposes, since it has the same nature and is perhaps more powerful.

Jan 1, 1942

By O. H. Banes

The electrolytic zinc plant of the American Zinc Company located at Sauget, Illinois started operations in April 1941. The plant had a designed capacity of 45(T) per day. The original flow sheet was quite simple, incorporating the low density process. Through the years the capacity of the plant has been increased to the current design of 214(T) cathodes per day. This paper describes the current operation along with typical metallurgical data.

Jan 1, 1970

By J. Nutting, D. H. Kirkwood

The oxidation of lead sulfide in air between 200° and 350°C has been investigated by electron diffraction from thick sulfide films and from galena surfnces. It has been demonstrated that sulfate is the stable reaction product up to 570°C. Sulfate is HAGIHARA has investigated' single crystals of galena roasted in air by the reflection electron-diffraction technique, which owing to the very limited penetration of the beam into the crystal gives information of the nature of the surface only. He has shown that up to 280°C the first oxidation product is lead sulfate, followed by lead mono-oxysulfate (PbO . PbS04). At longer times and higher temperatures more complex patterns appeared which could not be analyzed. All of these patterns were of streaks or spots arising from crystals oriented on the galena surface, and it is probable that these crystals are lead compounds whose structures have not been determined, such as the other oxysulfates (2Pb0 • PbS04 and 4Pb0 . PbS04) or a number of oxides. Certain lead sulfide films, formed chemically, give ring patterns in transmission electron diffraction2 because they are polycrystalline, and should also give ring patterns of the products after oxidation. It was thought that a diffraction study would reveal the sequence of phases produced in the reactions at different temperatures, since X-ray powder patterns are available for many lead compounds. PREPARATION OF FILMS The films were prepared by passing H2S over a saturated solution of lead nitrate in water. Once a silvery film had formed on the solution surface, no further thickening was apparent. The films were transferred by a gauze to a bath of distilled water for washing and pieces of film were caught on small discs on which they were dried. The discs were formed initially on galena up to temperatures of 300°C, followed by oxide and oxysulfates in turn at longer times. The appearance of- these phases is believed to result from an inadequate rate of supply of sulfur to the top surface 01. the crystal. standard Siemens mounts, made of platinum alloy, and had seven 20-p apertures drilled through them. The parts of the film which had dried onto the disc surface were light blue in color, which is the interference color of a film about 600A in thickness. A strong pattern of lead sulfide was obtained in transmission electron diffraction through the apertures but slight broadening indicated a crystallite size of around 200A. Tilting a sulfide film in the beam produced arcing of the rings, increasing the intensities of the (Ill), (3111, and (222) rings and reducing (200) and (220). This arises from preferred orientation in the film, a [loo] direction of the crystallites being normal to the plane of the film. These specimens were oxidized in an oven maintained at the required temperature. The reported times include that taken to heat the film to the reaction temperature. STABLE PHASES FORMED IN OXIDATION The conditions in which various oxidation products of lead sulfide are stable have been considered by the authors in a previous paper.3 It was shown that in a normal atmosphere, taken as containing lo-' atm of SOs, lead sulfate would be stable up lo about 570°C. This was confirmed by oxidizing thin films of sulfide for several days, and the analysis of the transmission-diffraction pattern is given in Table 1. The fit with the patt$rn from X-rays is good, except for the missing 3.62A ring. Some disagreement in intensities of reflections given by X-rays and electrons is to be expected. Up to 570°C a spotty pattern of sulfate was still obtained, indicating grain growth, but above this temperature the film disintegrated. Probably this is associated with the decomposition to PbO . PbS04. It needs to be emphasized that the atmosphere

Jan 1, 1965

By K. Verghese, R. W. Rousseau, R. P. Gardner

A radioactive tracer method and a size-discretized, mass balance model are formulated and demonstrated in a feasibility experiment for the determination of crystal growth rates in MSMPR crystallizers. The system studied is aqueous KN03 with K-42 as the radioactive tracer. The results indicate that the method should prove to be very valuable for this application, particularly when systems exhibiting size-dependent growth rates are of interest. An indicated refinement to the tracer method is the simultaneous use of an additional tracer in the liquid to determine the amount of radioactivity from the liquid that is adsorbed on the samples of filtered crystals.

Jan 1, 1980

THE 145th* meeting of the American Institute of Mining and Metallurgical Engineers was held in New York, Feb 17-21, 1936 On the fifth day, Feb 21, an Institute party journeyed to Schenectady, N Y, and made there a tour of inspection of the "House of Magic" of the General Electric Co The meeting proper (Feb 17-20) consisted of the annual business meeting, 43 technical sessions at which 214 papers were presented, two regular sessions of the Board of Directors, two conferences of Section and Division Chairmen, the second of which was attended by the Board of Directors, a late afternoon session for Student Associates and members of Affiliated Student Societies and Student Chapters, which was addressed by President Buehler, Dr George Otis Smith and others, two formal lectures, luncheon Monday, Tuesday and Wednesday for members and guests, four group dinners and ten group luncheons, nineteen committee meetings, the annual reception and dinner-dance, an informal dance, a dinner-smoker and the anual meeting of the Woman's Auxiliary The attendance record for the past three annual meetings follows (figures are in the order 1936-1935-1934) total registration, 1658¬1609-1534, dinner dance, 666-577-543, dinner-smoker, 528-490-425, informal dance, 218-279-295, women's registration, 184-179-160, excursion, 183 (1936), luncheons, 1135-1132-1034 The Mineral Industry Education Division met at the Engineering Woman's Club Sunday afternoon and evening, Feb 16, with 55 present Three problems of current interest were discussed accrediting of engineering schools by the Engineers' Council for Professional Development, the question of what metallurgical engineers shall be taught, and the need for more attention to the industrial minerals in the curricula of mining schools A buffet supper was served In the evening the meeting became a joint session with the Industrial Minerals Division A second session of the Division was held on Wednesday afternoon, Feb 19, in the Engineering Societies Building The Sunday meeting was the only Annual Meeting technical session held outside the building

Jan 1, 1937

By Fred H. Poettmann

An equation has been derived for use in calculating the sandface pressure of flowing gas wells in which the variation of the compressibility factor of the gas with pressure is taken into consideration. This variation due to compressibility has been put into both graphical and tabular form. Comparison of calculated results with field measured results were made on 20 dry gas wells from a given field and 11 distillate wells from different fields. The agreement between calculated and observed results is good. In addition to their use in the calculation of sandface pressures of flowing wells, the factors can be used in the direct calculation of the static bottom hole pressure of gas wells, the capacity of gas transmission lines, and in the calculation of the theoretical isothermal horsepower necessary to compress a natural gas. Examples demonstrating the use of various equations are given. INTRODUCTION Many of the equations used to calculate the sandface pressures of flowing gas wells from well head data do not take into consideration rigorously the deviation of the natural gas from ideal gas behavior. For low pressure wells this error is not serious. For high pressure wells flowing at high rates this error call be serious. Sandface pressures are used to determine the producing capacity of gas wells as shown in the U. S. Bureau of Mines' Monograph 7.' An equation has been derived for use in calculating the sandface pressure of flowing gas wells in which the variation of compressibility of the gas with pressure is taken into consideration. This variation due to compressibility has been put into both graphical and tabular form. In addition to their use in the calculation of sandface pressures, these "factors" can also be used to give a direct solution in the calculation of the static bottom hole pressure of gas wells, the calculation of the capacity of gas transmission lines, and the calculation of the isothermal horsepower necessary to compress a gas. CALCULATION OF SANDFACE PRESSURE OF FLOWING GAS WELLS The starting point in the derivation of any specific flow equation is an energy balance on the fluid flowing between any two points in the system. This energy balance based on one pound of flowing fluid is expressed by the well known general flow equation: jp~- vdP+ Ah + -— + wt + r. = o . . (i) P, 2 g. where V = specific volume of flowing fluid in cu ft/lb P = pressure in Ib per sq ft ah = difference in height above datum plane in, ft ------ = kinetic energy change of one lb of flowing fluid, v equals velocity in ft/sec and g. = 32.174 Ws = Work done by fluid while in flow (similar to shaft work in driving a turbine) W, = Znergy losses due to the irreversibilities of the flowing fluid This equation contains no limiting assumptions and can be made the basis of any fluid flow relationship by limitations or substitutions. The energy units are usually expressed in term* of foot-pounds of energy per pound of mass. Considering the vertical flow of gas through tubing or annu-lus, the external work W, done by the gas is zero. Let us also assume that the value of the kinetic energy function is small and can be neglected. Equation (1) is reduced to: /P: VdP + Ah+Wt = 0 .......(2) Pi The energy loszes PI can be expressed in terms of the well known Fanning equatinn: 4/Lf: rf = —— ............(3) 2g,D where L = the integrated average velocity in ft/sec of vertical flow in a uniform flow string -~h = L v = the integrated average velocity in ft/sec / = dimensionless correlating function

Jan 1, 1951

By Fred H. Poettmann

An equation has been derived for use in calculating the sandface pressure of flowing gas wells in which the variation of the compressibility factor of the gas with pressure is taken into consideration. This variation due to compressibility has been put into both graphical and tabular form. Comparison of calculated results with field measured results were made on 20 dry gas wells from a given field and 11 distillate wells from different fields. The agreement between calculated and observed results is good. In addition to their use in the calculation of sandface pressures of flowing wells, the factors can be used in the direct calculation of the static bottom hole pressure of gas wells, the capacity of gas transmission lines, and in the calculation of the theoretical isothermal horsepower necessary to compress a natural gas. Examples demonstrating the use of various equations are given. INTRODUCTION Many of the equations used to calculate the sandface pressures of flowing gas wells from well head data do not take into consideration rigorously the deviation of the natural gas from ideal gas behavior. For low pressure wells this error is not serious. For high pressure wells flowing at high rates this error call be serious. Sandface pressures are used to determine the producing capacity of gas wells as shown in the U. S. Bureau of Mines' Monograph 7.' An equation has been derived for use in calculating the sandface pressure of flowing gas wells in which the variation of compressibility of the gas with pressure is taken into consideration. This variation due to compressibility has been put into both graphical and tabular form. In addition to their use in the calculation of sandface pressures, these "factors" can also be used to give a direct solution in the calculation of the static bottom hole pressure of gas wells, the calculation of the capacity of gas transmission lines, and the calculation of the isothermal horsepower necessary to compress a gas. CALCULATION OF SANDFACE PRESSURE OF FLOWING GAS WELLS The starting point in the derivation of any specific flow equation is an energy balance on the fluid flowing between any two points in the system. This energy balance based on one pound of flowing fluid is expressed by the well known general flow equation: jp~- vdP+ Ah + -— + wt + r. = o . . (i) P, 2 g. where V = specific volume of flowing fluid in cu ft/lb P = pressure in Ib per sq ft ah = difference in height above datum plane in, ft ------ = kinetic energy change of one lb of flowing fluid, v equals velocity in ft/sec and g. = 32.174 Ws = Work done by fluid while in flow (similar to shaft work in driving a turbine) W, = Znergy losses due to the irreversibilities of the flowing fluid This equation contains no limiting assumptions and can be made the basis of any fluid flow relationship by limitations or substitutions. The energy units are usually expressed in term* of foot-pounds of energy per pound of mass. Considering the vertical flow of gas through tubing or annu-lus, the external work W, done by the gas is zero. Let us also assume that the value of the kinetic energy function is small and can be neglected. Equation (1) is reduced to: /P: VdP + Ah+Wt = 0 .......(2) Pi The energy loszes PI can be expressed in terms of the well known Fanning equatinn: 4/Lf: rf = —— ............(3) 2g,D where L = the integrated average velocity in ft/sec of vertical flow in a uniform flow string -~h = L v = the integrated average velocity in ft/sec / = dimensionless correlating function

Jan 1, 1951

By J. W. Stewart

That our American civilization will have extensive postwar problems in such fields as economics, unemployment, and social adjustment is now well understood by all readers of the press and listeners to the radio. But precious little is heard from these sources regarding the impact of the war on education, though education is one of the fields where the effect of the war is going to be felt most-for youth is fighting the war. Unquestionably, serious educational problems will ;rise in the postwar period, challenging the best efforts of our educators. Most acute will be the problems at the college level of education, for it is this age group that will have had its educational process most thoroughly disrupted. The return of these students to our college and university campuses wiI1 bring about a new set of conditions which we might as well try to foresee and begin to prepare for now. To begin with, the average returning college student who has had his education interrupted by war service will certainly be more mature in both years and mental outlook, and possibly married. As a result he will want to finish his college education as quickly as possible. His natural action will be to shop around among the various schools of the country to see where he can get the most credit for work he has done or thinks he has done. It is just possible that what might impolitely be termed "dark - market" schools may arise to cater to his needs. These schools will not think of them- selves in this light, of course, but will be conscious only of a keen sympathy for the veteran student and an urgent desire to help him solve his pressing problems. A considerable number of American colleges are going to be pretty well impoverished before this present war is ended and unless some professional organization takes it upon itself to place this possible situation under supervision and regulation, we may well suffer a serious setback to the

Jan 1, 1944

By Ronald C. Koo

THE effect of grain size on the mechanical properties of the bcc metals has been a subject of intensive theoretical and experimental study.'-l5 Quantitative relationships have been established experimentally between yield stress and grain size and between the ductile-brittle transition temperature and grain size in a number of metals.6"15 Much significance has therefore been attached theoretically to the grain size dependence. In all these experiments, different grain sizes were always achieved by annealing specimens at various temperatures. The implicit assumption was that any change in the dislocation substructure or in the distribution of impurities which might occur simultaneously with the production of various grain sizes had only a negligible effect on the mechanical properties. The validity of this assumption, however, is questionable. transformation in iron-nickel alloys is actually an extraneous phenomenon due to inadvertent compositional changes in the martensite if the heating rate is not sufficiently rapid. This complication can be avoided by up-quenching for the reversal treatment,5 and then the stabilization does not appear. Clearly, the lattice imperfections and strengthening produced by the reverse transformation are not responsible for the marked stabilization which has been observed by other investigators in these alloys. Data will be presented in this note to show that, at least in recrystallized tungsten of commercial purity, the difference in the ductile-brittle transition temperature of specimens annealed at various temperatures is more a result of a variation in the distribution of impurities rather than of the difference in grain size produced by the anneal. Ductile-brittle transition temperatures in tension were determined on powder-metallurgy tungsten specimens recrystallized at various temperatures. Tensile specimens having a gage length of 1.50 in. and gage diam of 0.18 in. were recrystallized at 1450°, 2000°, 2350°, 2550°, 2750°, or 2800" for 30 min in a vacuum furnace at a pressure of 1 x 10"5 mm of Hg and then tested at a constant extension rate of 8 x 10 per sec in an argon atmosphere from 100" to 800". Typical quantitative analyses of impurities are given in the Table. These results show that, within the precision of the analyses, see Table, annealing did not result in any detectable change in the impurity contents of the specimens, nor was there any detectable difference in purity between specimens having large differences in grain size annealed at the same temperatures . The results of the tensile tests yielded three distinct ductile-brittle transition curves approximately 225' apart. As shown in Fig. 1, data of specimens annealed at 1450°C and those of specimens annealed at 2000°C (O) fell on Curve A. Data of specimens annealed at 2350" and 2550°C fell on Curve B, and those of specimens annealed at 2750" and 2800°C fell on Curve C. The decrease in ductility with increase in annealing temperature became so pronounced that one third of the specimens annealed at 2750" and two thirds of the specimens

Jan 1, 1963

By J. F. Keefe, C. J. Bier, O&apos

This study was carried out with copper because it represents the simplest form of sintering, in that but one metal is involved and all reactions occur in the solid state. The present work will cover three variables affecting the sintering process; namely, briquetting pressure, sintering temperature and time in hot zone. Although strength and dimensional changes were observed, this is primarily a metal-lographic study of the sintering process in copper. The term "sintering" should be understood to mean the process by which the metal powder particles of the compact become united into one body. Material Used The copper powder used was made from reduced copper oxide, and is typical of a grade used for the mass production of parts formed of metal powders. The screen analysis of the powder was as follows: Per Cent Per Cent BY BY Particle Size "Weight Particle Size "Weight Mesh Microns /80.... 0.00 43/32.... 17.49 80/I00..... 32/20......16.68 100/140.... 0.34 20/10.... 23.14 140/200___ 15.25 10/5..... 4.64 200/230....... 5.00 5/0...... 0.75 230/325.... 16.70 — 325....62. 69 The minus 325-mesh analysis was made by using a Roller Air Analyzer.1,2 The apparent density is here defined as the weight per cubic centimeter of the loose, unpacked powder as measured with the Hall flowmeter. The value for the powder used was 2.57 grams per cubic centimeter.

Jan 1, 1945

By G. Carman Ridland

In conjunction with a geological investigation of the silver-bearing veins at Contact Lake, Northwest Territories, Canada, a survey was made with a Geiger-Miiller counter of the gamma-ray emissions from the rocks in the vicinity of the mine workings. Discontinuous pitchblende veins have been encountered occasionally in the silver-bearing fissures, and the geophysical survey was undertaken with the hope that abnormally high gamma-ray intensities, if detected, might lead to larger and more continuous pitchblende discoveries. Before the instrument was used at Contact Lake, preliminary tests were made, first with laboratory specimens at Princeton University, and later over known pitchblende deposits at the Eldorado property, LaBine Point, N.W.T. The Geiger-Müller counter, as adapted for field use, is described; the technique of transporting and operating the instrument is outlined; and the general precautions to be observed are discussed. The results obtained at Great Bear Lake show that the instrument is capable of detecting not only a pitchblende ore shoot in a shear zone, but also the mildly radioactive "host rock" at a considerable distance from the ore body. Hence, use of the Geiger-Müller counter is urged, not just for the detailed search for an ore body in a shear zone, but for the detection of possible radioactive "host rocks" in large-scale reconnaissance surveys of unexplored regions made by prospectors and members of federal geological survey parties. Location.—Along the rocky eastern shores of Great Bear Lake, in the Northwest Territories of Canada, lies one of the world's great radium-producing areas. The Eldorado mine, owned and operated by the Eldorado Gold Mines, Ltd., is at LaBine Point; while the Contact Lake mine, operated by Bear Exploration and Radium, Ltd. (B.E.A.R.), lies 9 miles to the southeast of LaBine Point and 2 miles south of Echo Bay, an indentation in the eastern shore line of Great Bear Lake. Geology.—The Eldorado company obtains its radium by the mining of the mineral pitchblende, which is found associated with a complex variety of metallic and nonmetallic minerals1 in quartz-carbonate veins occurring in metamorphosed pre-Cambrian sediment aries. Most of the pitchblende is intimately associated with a brown quartz and belongs to an early hydrothermal stage of mineralization during which safflorite-rammelsbergite and minor cobalt-nickel minerals were also deposited. Some pitchblende occurs with a group of minerals belonging to a later stage of mineralization in which the gangue is mainly dolomite and sometimes ferruginous rhodochrosite. Associated with this group are native silver and lead-zinc-copper sulphide minerals. The Contact Lake property owes its existence to the mining of rich, native silver ore shoots, which are

Jan 1, 1946

By G. Carman Ridland

In conjunction with a geological investigation of the silver-bearing veins at Contact Lake, Northwest Territories, Canada, a survey was made with a Geiger-Miiller counter of the gamma-ray emissions from the rocks in the vicinity of the mine workings. Discontinuous pitchblende veins have been encountered occasionally in the silver-bearing fissures, and the geophysical survey was undertaken with the hope that abnormally high gamma-ray intensities, if detected, might lead to larger and more continuous pitchblende discoveries. Before the instrument was used at Contact Lake, preliminary tests were made, first with laboratory specimens at Princeton University, and later over known pitchblende deposits at the Eldorado property, LaBine Point, N.W.T. The Geiger-Müller counter, as adapted for field use, is described; the technique of transporting and operating the instrument is outlined; and the general precautions to be observed are discussed. The results obtained at Great Bear Lake show that the instrument is capable of detecting not only a pitchblende ore shoot in a shear zone, but also the mildly radioactive "host rock" at a considerable distance from the ore body. Hence, use of the Geiger-Müller counter is urged, not just for the detailed search for an ore body in a shear zone, but for the detection of possible radioactive "host rocks" in large-scale reconnaissance surveys of unexplored regions made by prospectors and members of federal geological survey parties. Location.—Along the rocky eastern shores of Great Bear Lake, in the Northwest Territories of Canada, lies one of the world's great radium-producing areas. The Eldorado mine, owned and operated by the Eldorado Gold Mines, Ltd., is at LaBine Point; while the Contact Lake mine, operated by Bear Exploration and Radium, Ltd. (B.E.A.R.), lies 9 miles to the southeast of LaBine Point and 2 miles south of Echo Bay, an indentation in the eastern shore line of Great Bear Lake. Geology.—The Eldorado company obtains its radium by the mining of the mineral pitchblende, which is found associated with a complex variety of metallic and nonmetallic minerals1 in quartz-carbonate veins occurring in metamorphosed pre-Cambrian sediment aries. Most of the pitchblende is intimately associated with a brown quartz and belongs to an early hydrothermal stage of mineralization during which safflorite-rammelsbergite and minor cobalt-nickel minerals were also deposited. Some pitchblende occurs with a group of minerals belonging to a later stage of mineralization in which the gangue is mainly dolomite and sometimes ferruginous rhodochrosite. Associated with this group are native silver and lead-zinc-copper sulphide minerals. The Contact Lake property owes its existence to the mining of rich, native silver ore shoots, which are

Jan 1, 1946

By William P. Blake

Copper Basin in Yavapai county, Arizona Territory, about twenty miles southwest of Prescott, is well named. It is a depressed area, and a region of cupriferous impregnation.* The geologic conditions are simple. The foundation rock is a coarse-grained granite and gneiss, in which soda feldspar predominates. There are also dykes of porphyritic rock, and a large quartz vein containing pyrites. Superimposed on this crystalline foundation, we find heavy beds of mechanically formed rocks, conglomerates, breccias, and sandstones, in horizontal layers cropping along the bed of a creek, and apparently the remnants of a much more extended formation, now denuded and largely carried away by gradual atmospheric erosion. The heavy beds of conglomerate are in many places much broken and tilted up, even standing on edge in large blocks, as if they had been lifted by some great convulsion; but the cause is much more simple, being merely the removal by gradual disintegration and erosion of the softened and decayed granitic rock below. The materials of these sedimentary beds are chiefly fragments of granite, gneiss, and plutonic rocks loosely mingled. They are the chief repositories of the copper-ore, which forms the cementing substance. This copper-ore is the blue and the green carbonate, azurite and malachite, and the ore is so generally spread through the mass of the beds that the blue and the green croppings can be seen at a great distance, particularly after or during a shower of rain, when the colors are extremely brilliant and beautiful. The copper carbonate is not only a matrix and a cementing material for the fragments of rock, but it invests and covers these fragments so that only malachite and azurite are visible. The beds are from three to ten feet or more in thickness, and, although seemingly solid carbonate of copper, rarely contain over 12 or 15 per cent. of that metal. Some portions of the conglomerates are much more highly charged with copper than others, and in places the beds are almost without copper. If a lump of the coarse sandstone

Jan 1, 1889

By Arthur F. Taggart

ENGINEERING education today is like a crazy quilt of somber wools and gaudy shoddy, chain-stitched on an academic assembly line, and sold at ever mounting prices to inexperienced youths for lifetime use. Each engineering school offers a half-dozen or so patterns with essentially the same skimpy wool content. Sales appeal is in the color of the shoddy, denoted by the hopeful adjectives chemical, civil and the like. This article is argument for an all wool product made by slow, careful handwork. Bluntly it proposes a thorough four-year undergraduate drill in fundamental science and general engineering empirics, leavened by continuing study of the third of the engineer's troubles: Man. It is not contended that existing methods of engineering education have failed to start men on the path to successful engineering practice (too many of you have started that way); rather, social conditions and the bounds of knowledge have changed tremendously, and corresponding alterations in the pattern of engineering education are overdue. We'll Teach the Specifics The first part of this contention is illustrated by excerpts from a letter received recently from an officer of one of the largest corporations: "We are interested in employing two or three outstanding young engineers to be placed on a special training program to develop them as design and construction engineers.... "We propose to put these men on a four-month indoctrination and orientation course after which they would be given job-training assignments for a period that will vary from about six months to about a year and a half depending upon the aptitudes, abilities and intelligence of the candidates.... "I am not too fussy about what kind of engineers the men might be insofar as academic courses are concerned. They could be.. . in almost any engineering classification.... We can furnish the additional training beyond the academic fundamentals. "The starting rate for these jobs would be $326 per month...." This letter is not unique; rather it is representative of a practice that has become common. It is industry's enforced response to the general refusal by young graduates to submit to union domination in order to gain operating experience at the labor level. The message to engineering schoolteachers is plain: You teach the fundamentals; we'll teach our practice and pay the graduate to learn it. The letter means to the student that time spent in school studying the specific practices of particular industries is waste compounded. The school can't give the equivalent of what industry teaches, wherefore industry will still demand apprenticeship. The student must pay for the specific instruction at school instead of being paid to take it later. And time-consuming specifics crowd out drill in basic scientific and technical subjects as well as liberal arts.

Jan 1, 1952

By J. D. Davis, A. C. Fieldner

The older coal chemist had a much simpler conception of coal than we have today. To him coal was a mineral composed essentially of carbon, hydrogen, oxygen, nitrogen, sulfur, ash, and water, in various proportions. His studies on the constitution of coal were directed along the conventional lines of proximate and ultimate chemical analyses and making deductions from these data without any real appreciation of the fact that coal is a conglomerate of various chemical compounds, including many of the most complex structures known to organic chemistry. The view of the modern coal chemist is well expressed by Franz Fischer,' who says that while proximate and ultimate analyses are important both from the scientific and technical point of view, they tell the chemist no more concerning the number and kinds of chemical compounds that constitute coal than the reader would learn of the contents of a book if told that the printed contents consisted of 15 per cent. of the letter "e," 5 per cent. of the letter "n," 1 per cent. of the letter"g," 4 per cent. of the letter "b," etc. As the reader must have the grouping of letters into words and words into sentences, so the chemist must have the grouping of atoms into molecules and the proportion of each molecular compound in the coal aggregate before he acquires an adequate knowledge of the constitution of coal. Modern investigators2 are laying the foundation of a new chemistry of coal based on the biochemistry of plants and the chemical changes involved in processes of fermentation and decay. As

Jan 1, 1925

By Thomas T. Read

Readjustment of the industrial world to a peace basis after more than 4 years of war will involve many fundamental and far-reaching changes that cannot as yet be clearly foreseen or definitely provided for. Such problems may be subdivided, in the vocabulary of war, into those involving material and those centering about personnel. Of the two, the latter group is the more difficult and obscure, as the factors involved are less clearly understood and the methods to be followed are not yet tested and standardized. When it is said that the market is weak, stocks large, and demand light, every business man understands clearly what is meant and what course he should adopt to adjust himself, so far as possible, to such conditions. But when it is said that the rapid spread of Bolshevism in Europe is a danger to industrial organization in this country, it is difficult to have any assured sense that all that the statement may mean is clearly understood or that the means to be followed to meet such a situation are definitely known. Since Bolshevism is primarily a mental phenomenon and since the rupture it brings about in industrial organization should be prevented, if possible, it is my purpose to restrict this discussion of the activities of the Committee on Industrial Organization to some of its mental aspects, as the chairmen of the sub-committees, from their special knowledge of their own fields, can best set forth recent progress in the lines with which they are especially concerned. The first requisites of success in industrial organization, as in the biological organism of which it is the social counterpart, are unity of purpose and coordinated activity. Typical good and bad examples of this' are the relative parts that the United States and Russia have played in the great war. These two factors are primarily mental, and it is not difficult to view the mental aspects of all problems of industrial organization as the most important ones. Unless we can attain unity of purpose and coordinated activity in industry, the provision of comfortable homes at reasonable rent, the assurance of steady work at good wages, the elimination of industrial accidents, and provision against want in old age or in case of disability will have brought us no nearer to our real goal.

Jan 1, 1919

By H. E. Rorschach

Activity in Oklahoma oil fields made 1937 one of the best years since 1926. During the year, 3454 wells were completed, an increase of about 25 per cent over the year 1936. Purchasers reports filed with the Corporation Commission of the State of Oklahoma showed a total of 221,842,-788 bbl. of oil purchased from leases in 1937, an increase of about 10 per cent over 1936. The assembly of a complete table of all of the oil fields in Oklahoma has not yet been achieved. Many of the early records of operators and pipe-line companies are incomplete. Table 1 includes all of the new fields, and this year there has been added work done covering pools discovered in previous years, so that most of the important fields in the state of Oklahoma are included therein. The outstanding development of the year was the discovery of the producing horizon classified as the Wilcox in western Payne County by the Mid-Continent Petroleum Corporation on a unitized block in sec. 18, Tp. 18 N., R. 2 E. This block is operated hy the Mid-Continent and owned in conjunction with the Carter Oil Co., Transwestern Oil Co. and Sinclair-Prairie Oil Co. Another important development of the year was the extension of the deep zone in the old Fox-Milroy area of Carter and Stephens Counties. Some of the other discoveries made during the year 1937 are South Cromwell, discovered by Sinclair-Prairie Oil Co.; Cromwell extension of the Fitts pool in Pontotoc County; discovery of the Langston area in Logan County; discovery of the Sporn area in Lincoln County by Skelly Oil Co. and the discovery of the North Wellston area in Lincoln County by Standard Oil & Gas Co. Table 2 shows the new oil areas discovered in Oklahoma during the year 1937 and areas that were discovered in 1936 but developed in 1937. Fox-Milroy Area.—Three wells were completed to the deep producing zone during the year. One of the wells completed in the early part of the year uas the Carter Oil Company's No. 1 Harley in sec. 24, Tp. 2 S., R. 4 W., 3 1/2 miles northwest of the original discovery well, the Ruth

Jan 1, 1938

By T. Sterry Hunt

I HAVE in a previous communication called the attention of the Institute to the geognostical relations of the crystalline iron ores belonging to the Eozoic rocks of North America, at which time I noticed (1) those associated with the gneisses of the Laurentian series, (2) those of the crystalline schists of the Huronian, as seen in Northern Michigan and in many localities along the Appalachians ; (3) those of Southeastern Missouri associated with petrosilex porphyries and schistose rocks, and presumed to be nearly of the same age with those of the Huronian schists; and (4) the highly titaniferous ores of the Norian or Labradorian series from Essex County, N. Y., and from various parts of Canada. It may here be remarked that, although the presence of titanium is most marked in the Norian ores, this objectionable element is sometimes found in the schistose ores of the Huronian, and to a lesser extent in certain Laurentian magnetites. The ores of each of these geological divisions have their individual peculiarities, which serve to distinguish them to such a degree that the magnetites and specular ores of the Laurentian are as dissimilar to those of the Huronian as are the crystalline silicated rocks of the two series. As it happens that these mineralogical dissimilarities correspond to differences in composition and in adaptability to different processes of manufacture, which, in the present condition of the iron industry, are objects of special consideration to metallurgists, it will be seen that these geognostical distinctions become of great practical importance. During the past year I was desired by the Geological Commissioners of Pennsylvania to devote a few weeks to certain geological studies in the eastern part of the State, in the course of which I was enabled to make, with regard to its crystalline iron ores, some observations to which I desire to call the attention of the Institute. I may mention, in passing, that the great South Mountain belt, from the Schuylkill to the Delaware, is composed of Laurentian rocks, in which are found the characteristic ores of the series like those of the Highlands of New Jersey and New York, and of the Adiron-

Jan 1, 1876

By John Lovejoy

As the Seminole area, Seminole and Pottawatomie Counties, Okla., appears to be the chief danger zone of overproduction in the United States, it may be of interest to review the production records of the various pools which make up this area; also to dis-cuss the future prospects of these pools, together with the structurally "high" points which may develop into new pools. It is also of interest to appraise the effect of the curtailment program in this general area, which was agreed to in principle by the various Seminole op-erators at a meeting held on May 23 at the offices of W. C. Teagle in New York. There are four large pools in the greater Seminole area. They are, in the order of their importance Seminole City, Bowlegs, Earlsboro, and Searight pools. A glance at the accompanying general map of the area will show their relative situation. The detail maps show the extent and area of these prolific spots. Seminole production comes from the Wilcox sand of Ordovician age, found at a depth of 3900 to 4300 feet. Semninole City Pool:-This pool was discovered in Wilcox sand in July, 1926. By Jan., 1927, there were 123 wells completed, making 146,000 bbl. per day. The field reached its peak of 253,000 bbl. per day the last week of Feb., 1927, with 211 completions and a per well average of 1200 bbl. On July 4 there were 304 wells completed, producing 102,000 bbl., with a per well aver-age of 336 bbl. per day. This pool will cover an area of approximately 3500 acres. It has produced approxi-mately 38,000,000 bbl. to. July 1. Estimates of total ultimate production are around 55,000,000 bbl. or somewhat better than 15,000 bbl. per acre. Some of the individual leases have already yielded 30,000 and 40,000 bbl. to the acre. Bowlegs Pool:-This pool shows 175 drilling wells and 131 completions making 180,000 bbl. per day, with an average per well production of 1380 bbl. It appears that this pool will develop into nearly as large an area as Seminole City. The wells, however, do not give up

Jan 8, 1927